VMware ESXi 4.1 and Areca controller

Similar Questions

• VMware ESXi 5.5 and HP ML310e gen8 v2 lose the license and the password after restart

  I've updated my HP Proliant server with the latest drivers and I have the BIOS version is here: VMware Compatibility Guide: search system

  but after I entered my license in vSphere and adding a virtual machine to the host, where I am restart I lose the license, the password to connect to the host (his game empty) and all virtual machines (I have to add them manually and fix the network, because it is also reset to the default setting).

  Any ideas why is this happing? I'm doing something wrong?

  Other info: I have 2 hard drives put in a logical drive (Raid 1) and VmWare log does not work without saying anything...

  Hello

  is it a stand alone esx host? If yes try asking another key on the wmare site

  hp custom image you used to install the esxi?  If not download the latest version of the hp site or vmware and perform a new installation or level and keep the data store.

  also update the firmware of the hp for the later levels site

• VMware ESXi WARNING - battery on the controller workload 0...

  Hello world

  I get this warning frequently daily some of my ESXi server that runs on Dell Power Edge 2950 - III:

  Status: Warning (yellow)

  Alarm: State of the sensor changed hardware host

  Duration: 2010-10-24 22:30:55

  Sensor "on controller 0 battery charge...". "equal attention.

  Sensor 'State of health Rollup VMware' equal attention

  is there something wrong with my server ESXi?

  Thank you.

  As written it is a normal feature of the PERC controller which has a cycle of learning for the battery.

  On vsphere 4.0 this task generate a lot of alarms, but after I upgraded to 4.1 I got the alarms only during the learning cycle.

  André

• VMWare Esxi 4.0 and 5.0 even environment

  Hi guys,.

  I have a client where they use 4.0 and 5.0 in a mix environment. And im trying to convince them to update everything to 5.0.

  Are there problems in terms of compatibility and features that they cannot use, if they are in different versions?

  Hello

  I myself use a mixed environment. If it works if you follow a few rules

  Some limitations are:

  ESXi 4 servers cannot access 5 VMFS LUNS.

  Virtual machines with version 8 of material can not turn on on the ESXi 4 servers.

  Storage DRS works only with ESXi 5 hosts.

  There is probably more limitations.

  Concerning

• Best practices for Exchange 2003 with VMWare ESXi 3.5 and iSCSI SAN

  Hello guys,.

  Here's the Q? We have 1 physical Exchange 2003, the HOST of 4 and 1 iSCSI SAN with LUN 3, 1 for data, 1 for VMWare and 1 for SQL, if we're going to virtualize it, I don't know where to put data Exchage and newspapers. I do not think that that is a good practice to put together the data but I do not have another SAN. So, what can I do?

  Thank you.

  We have 813 mailbox.

  I agree with cainics, start an average size and go from there.  I know it's a production mail server and you can not exactly 'play' with the settings because this requires time, but if you do the VM too big, you would have nothing left for other virtual machines.

  I would go 2 vCPU and at least 4 GB of RAM, maybe 8GB.  There must be parameters for the Exchange mailbox 813 and X users # to implement your environments in order to get an idea of the amount of RAM that will be... 4GB seems minimal to me, but 8 GB would probably be better like that.

• Version numbers of VMware ESXi, ESX, (confusion)

  Hello

  I have a case of support for Adaptec about the inability to manage my RAID array (on a map of Adaptec RAID 3405 controller) go in VMware ESXi 3.5. That's what they told me 'Nucleus OSin fact currently VMWARE ESX - i is not supported. Sorry, I should have mentioned this in my previous answer, I was not aware that there is a difference in the standard implementation of VMWARE ESX 3.5'.»

  Is there a VMware ESX 3.5 as a VMware ESXi 3.5 aswell? What is the difference? I thought VMware ESX ended with version 3.0, replaced by VMware ESXi 3.5 and later versions?

  If I look at the operating systems supported for the Adaptec RAID 3405 controller I find "VMware ESX Server 3.5"...

  ESXi and replace DO NOT ESX.  The reason why I gave you the comparison is because you can see what each call to savings.

  ESXi, is short, ESX less the service console.  Both are Virtualization platforms.

• Is VMWare ESXi 5.5 free?

  
  I installed VMWare ESXi 5.5 and vSphere cleint test lab and what I see is a 60 day trial, how can I get a free version?

  As mentioned André you missed the stand-alone host licenses section.

  If you are too confusing, here are the steps

  To allow a standalone ESXi 5.x (vSphere Hypervisor):

  1. Connect to the ESXi host with vSphere Client.
  2. Click the Configuration tab.
  3. Click licensed features in software.
  4. Click change in the appearance under the license tab.
  5. Select assign a new license key at this host.
  6. Press enter and enter the license key.
  7. Click OK.

• MS ISA/TMG on a security platform VMware ESXi?

  Hello

  I started last year virtualize our servers to VMware ESXi 4.1 and all running perfect.

  The only server that I've not virtualized was Microsoft Forefront threat Management Gateway 2010 (TMG server).

  But Friday our server collapsed, and I have no choice but to restore a backup of TMG on an ESXi server.

  Who then got connected to the internet to work as a gateway/firewall in 1 hour approximately, that this has been done.

  But I've always had this idea that he not great security wise to put a firewall/gateway server on an ESXi host with direct connection to the internet.

  Ofcouse the NETWORK card is attached to only this guest (TMG server),

  But my concern is really ok? or is there no direct safety problem to have my ESXi directly connected to the ISP?

  If there is no problem of security, it will be easy to simply continue to use this host and toll-free addictional on hardware.

  Best regards

  Thomas Nissen

  Thank you for your e-mail. I am on the emergency leave, cannot access my email. If your query is urgent please email [email protected]<>[email protected]>.

• 3.5 VMware esxi

  I have a dell poweredge 2600, I have vmware esxi 3.5 and it has 5 hard drives in raid format

  When I install vmware it shows only 10 gig hard dirve, it must indicate the total amount of 250 concerts

  can someone help me understand why he's not seen the other drives?

  Thanks a lot for your help in advance

  you will need to make your smaller RAID sets, as the limit is 2 TB minus 512 b

  http://www.VMware.com/PDF/vSphere4/R41/vsp_41_config_max.PDF

• HP Proliant Gen8 DL380e not charge controller B320i with VMWare ESXi 5.0 U3

  Hello community.
  
  Iam trying to install VMWare ESXi 5.0 U3 on a HP Proliant DL380e Gen8 server that has a B320i controller, I'm using support custom installation of HP, but yet when I select target the device doesn't show anything, I tried to raid 1+ 0 and raid 5, but I get No result.
  
  Ce is ISO which I download.
  

  https://my.VMware.com/Web/VMware/details?downloadGroup=HP-ESXi-5.0.0-U3-OCT2013 & ProductID = 229

  
  try Added to ISO customize the controller driver, but the ISO tells me that that driver already exists.
  

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=MTX_0a122ebcbbac4c469ca9acd1ae

  
  In le BIOS J’ai activated the next option.
  

  http://h20564.www2.HP.com/hpsc/doc/public/imageServlet?docid=emr_na-c03907472-1/c03871500.jpg

  You can try the custom HP VMWare 5.5 ISO instead? Or do you need a reason 5.0 any?

  I'm running a Gen8 DL380e with 5.5 Update 1 without problems. 5.5 Update 2 has some problems about the new version of the hpvsa driver that gives massive drops in virtual machines to run.

  You have a BBU (battery backup) installed?

  It is also for the execution of the last PSP (Proliant ServicePack) to get the latest firmware and the BIOS before installing.

• Best practices in VMWare ESXi 3.5 installation and deployment of VMDK u3?

  Hi all

  I'm about to implement virtualization on my business technology

  I've got these resources to be used by VMWare ESXi 3.5

  Dell PowerEDGE 2950 III

  • 32 GB DDR - II 667 MHz

  • internal 4 x 500 GB SATA 7200 RPM HDD (RAID 5) - I know that it's slow to host the VMDK

  • Internal USB slot on the motherboard (but not USB flashdisk?)

  Dell PowerVault MD3000

  • 10 x 300 GB SAS 15 k RPM

  • 2 x Dual port Gigabit Ethernet NIC (x 4 in total)

  • iSCSI - 2 x Gigabit Ethernet for the switch (mute not to VLAN)

  I wonder where I should install the VMWare ESXi? for the VMDK, I believe that the deployment in the SAN is the right place.

  and any suggestion for the use of the SATA HARD drive internal?

  any comments would be greatly appreciated.

  Thank you.

  You mean Deployment.jpg diagram?

  In this case, there is an error.

  You need a network 2, not 4.

  Each controller and each NIC (on ESX) must have an IP in a net and another IP in the second NET.

  ESX guests 4 targets, 2 in a net, 2 in the other.

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• 2808 LAG for use with VMware ESXi and Linux collage

  I posted the month last about setting up my work with groups LAG http://en.community.dell.com/support-forums/network-switches/f/866/t/19537080.aspx servers (I'll effectively implementing implement this Saturday)

  I decided to buy a 2808 for my ESXi server get more aggregated connections to my staff iSCSI Linux server but now I'm worried I might have made a mistake to buy the 2808.

  After looking in the manual before I realized I could have been mistakenly assuming that the 2808 had STP and LACP, as I can't find LACP anywhere in the PDF file. I guess that the configuration of my Linux machine for 802.3ad is out (a hope to make mode 4), so now for the configuration of my house, I wonder (* 1 *) that I have to configure my VMware NIC team like and what mode of binding should I use on my Linux host? As for the section at the top (my working configuration) (* 2 *) I don't know what to do about the road other than the leave as 'route based on originating virtual port ID "? (This is how our other data centers are configured, but I'm waiting for my admin network as agglomerates ESXi hosts are configured with the channels of port on our cisco switches)

  For the House, I want to try to increase the bandwidth by using three NICs in each server, I was hoping that it works:
  VMware: Route of IP hash function?
  w/Linux: balance-alb?

  -VMware:
  Before you begin:

  • The default load balancing strategy is route based on the port virtual origin ID. If the physical switch uses the aggregation of links, route based on the IP hash load balancing should be used. For more information, see host requirements for the aggregation of links for ESX and ESXi (1001938) and the guide of VMware Virtual Networking Concepts .
  • LACP support was introduced in vSphere 5.1 on distributed vSwitches and requires additional configuration. For more information, see activation or deactivation of LACP on a group of ports Uplink using the vSphere Client Web (2034277).
  • Ensure that the Protocol of aggregation VLAN and link (if any) are correctly configured on the physical switch ports.

  -Linux:
  * Descriptions of bonding modes *.
  + Mode 0 balance-rr: Round-robin policy: transmit packets in the sequential order of the first available through the last high school. This mode provides load balancing and fault tolerance.

  + 1 active-backup mode: Active-backup policy: only one slave in the link is active. A different slave becomes active if and only if, the active slave fails. MAC address of the binding is visible from the outside on a single port (NIC) to avoid confusion between the switch. This mode provides fault tolerance. The first option affects the behavior of this mode.

  + 2 balance-xor mode: XOR policy: transmit based [(adresse MAC XOR avec destination MAC traiterait de source) modulo County slave]. This selects the slave even for each destination MAC address. This mode provides load balancing and fault tolerance.

  + 3 broadcast mode: broadcasting policy: transmits everything on all slave interfaces. This mode provides fault tolerance.

  + Mode 4 802.3ad: IEEE 802.3ad dynamic aggregation of links. Creates aggregation groups who share the same speed and duplex settings. Use all the slaves in the active aggregator according to the 802.3ad specification.

  -Prerequisite:
  -1.Ethtool support in the base drivers to retrieve the speed and duplex of each slave.
  -Switch 2.A which takes care of IEEE 802.3ad dynamic aggregation of links. Most of the switches will require some type of configuration to activate 802.3ad mode.

  + Mode 5 balance-tlb: Adaptive load balancing transmission: Channel link that doesn't require any special switch support. Outgoing traffic is distributed according to the intensity of the current (relative speed) on each slave. Inbound traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave.

  -Prerequisite:
  -1.Ethtool support in the base drivers to retrieve the speed of each slave.

  + 6 balance-alb mode: Adaptive load balancing: includes balance-tlb plus receive balancing (rlb) for IPV4 traffic and doesn't require any special switch support. Receive load balancing is achieved by ARP negotiation. Link driver intercepts the ARP replies sent by the local system on their way and replaces the hardware address of source with the unique hardware address of one of the slaves in the bond as different counterparts use different physical addresses for the server.

  The topic dell nearest you, I have found a useful was: http://en.community.dell.com/techcenter/networking/f/4454/t/19415629.aspx

  my previous post was more concerned with VLAN tagging and spanning tree issues, but now I see I should have feared groups LAG it as well.

  Any help would be appreciated, thanks in advance all :)

  -

  PS. http://i.dell.com/sites/doccontent/shared-content/data-sheets/en/Documents/dell-powerconnect-2800-series-spec_sheet.pdf said that the 2800 series supports LACP, so if I'm worried about anything on my iSCSI side slap me please in the face, but I guess even in this case, I'm still not sure how to configure the ESXi host because it does not support LACP without vSphere and my original configuration is a free version , so I have no web vSphere management needed to make the LACP allow the change.

  Not sure if it is of no use: example configuration of EtherChannel / switches control protocol LACP (Link Aggregation) with ESXi/ESX and Cisco/HP (1004048), but that's where I was to base the choice on IP hash from.

  It must have the support of layer 3 to achieve IP hash, IP addressing is a 3-layer technology, so a 6200 series or higher or the soon to be released N3000 series.

• VCenter Server first to 5.5.0U3b update and later update of VMware ESXi ESX / will I have problems?

  Hello

  have trouble when I first updated my signature single vCenter Server and later update my vSphere hosts?

  A vCenter Server Version 5.5.0U3b should be able to manage vSphere Host Version 5.5.0 GA, right?

  Kind regards

  Roland

  The vCenter Server 5.5 update 3 b can manage VMware ESXi ESX release GA to 5.5 5.5 update 3 b, take a look: VMware product interoperability Matrices

  BUT, according to the interoperability matrices and vCenter Server 5.5 update 3 release notes, VMware strongly recommends you upgrade your hosts to 5.5 update 3 b, see:

  What's new

  • Update Support for the SSLv3 Protocol is disabled by default
    Note: In your vSphere environment, you must update vCenter Server vCenter Server 5.5 update 3 b before the update to 5.5 ESXi ESXi update 3 b. vCenter Server will not be able to manage 3B ESXi 5.5 update, if you update ESXi before update vCenter Server to version 5.5 update 3 b. For more information about the sequence in which vSphere environments must be updated, see KB 2057795.

  • VMware strongly recommends you update ESXi hosts to ESXi 5.5 update 3 b management of vCenter Server 5.5 updated 3B.

  VMware does not recommend the reactivation of SSLv3 because of the vulnerability of POODLE. If all you must enable SSLv3, you must activate the SSLv3 Protocol for all components. For more information, see

  KO 2139396

  .

  • Resolved issues. This version of vCenter Server 5.5 update 3 b solves the problems that have been documented in the resolved issues section.

• VMware ESXi 4.1.0 and snapshot problem - no disk space

  Hi all

  We now have a big problem with our free space on the disk. We are using VMware vSphere (vSphere Client ver 4.1.0 and VMware ESXi ver 4.1.0):

  Our vm has 2 HDD (500 GB, 1 TB). Now we have only 20 GB of free disk 1 and several snapshot files. To remove the snapshot, we need more than 20 GB of free space (corect?). What we need to do more free space? We can move snapshot files from the first disk to the second disk?

  

  

  Thanks for any help

  concerning

  Dragan

  First of all, you can redirect your new snapshot on another store/disk as explained in this article "http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1002929".

  Secondo, you can delete snapshot older and smaller but not all together as explained in this article by Duncan Epping "http://www.yellow-bricks.com/2008/01/07/delete-all-snapshots/."

  Alex

• Are there problems in the creation of a virtual machine in VMware Workstation or Server and then move it to ESXi?

  Hello

  I intend to pass our mailserver's current installation of Windows Server 2003 running on native hardware in a Windows Server 2008 running in a virtual machine on ESXi.

  This is the same machine as we will reuse so I would prefer to be able to create the virtual machine on a different computer and test it before wiping Windows and install ESXi. Are there problems with the creation of the virtual machine in VMware Server and then migrate to ESXi using VMware Converter? I won't if the result is not a 'perfect' virtual machine that performs as well as if it had been created on ESXi from the beginning.

  All our other VMs were created on ESXi from the beginning.

  Kind regards

  René Frej Nielsen

  If you are not sure, you can load VMware Server 2 and then install ESXi in it and test your configuration.  Do all this from your desktop (as it is decent).  You can also do in my computer.  A quick google search should give you all the information you need to get something like this configuration.