3.5 VMware esxi
I have a dell poweredge 2600, I have vmware esxi 3.5 and it has 5 hard drives in raid format
When I install vmware it shows only 10 gig hard dirve, it must indicate the total amount of 250 concerts
can someone help me understand why he's not seen the other drives?
Thanks a lot for your help in advance
you will need to make your smaller RAID sets, as the limit is 2 TB minus 512 b
http://www.VMware.com/PDF/vSphere4/R41/vsp_41_config_max.PDF
Tags: VMware
Similar Questions
-
Upgrade VMware ESXi 6.0 Update 2 VMware ESXi 6.0
Hello I am running my PowerEdge T110 II with VMware ESXi 6.0 - Dell customized image. I see that from April 15, 2016 Dell just introduced VMware ESXi 6.0 Update 2 and I'd like to update my system.
On the download page , I see there is an option to download and the ISO file. I wonder if this installation will completely be wipeout my existing VMware ESXi 6.0 - Dell custom and all the settings and I have to start all over again or update 2 ISO just 'modernize' my network?
Hello
You can use it to update without doing a new install. KB.VMware.com/.../Search.do; cmd = displayKC & externalId = 2109711 #Inter
-
Hi all
does anyone have experience with followed Bigbrother to host VMware ESXi?
In particular, I am interested monitor consumption of resources (CPU, memory, data warehouses) ESXi hosts.
I am happy to receive any information about this topic:
-experience in general
-scripts
-Links to the already existing scripts or documentation
- ....
Best regards
Stefan
Hello Stefan,
There is an existing extension that accomplishes what you want and it can be found at http://communities.quest.com/docs/DOC-5658 - I have not implemented this myself, but I've heard other users that it works very well. Let us know if this is consistent with what you are looking for, and we would be happy to help you with questions of integration.
Best,
John McNelly
Big Brother Team
-
That I improve a R710 and two v5.5 (Dell image) to v5.5 U2 ESXi ESXi R720 using the image of Dell here:
www.dell.com/.../DriversDetails
The documentation "Upgrade Guide to ESXi 5.5 using Dell customized Image" here:
indicates that a specific version of the megaraid_sas driver must be installed.
Is the version megaraid_sas that installs with the image of Dell U2 v5.5 not the right version?
I just ran the upgrade on a R710 and it's the megaraid_sas version installed:
~ # vmkload_mod s megaraid_sas | grep Version
Version: Version 06.803.73.00, build: 1331820, Interface: 9.2 inspired: August 22, 2014Thank you.
Hello
It lists the R720 and R710 systems supported and both link to the same page, so the customized version is the same for both servers. Is the version listed in the reference guide for A02
megaraid_sas - 06.803.73.00
This is the same version that he shows for your installation on the R710 so that seems correct.
-
Is the PowerEdge R610 Compatible DELL VMware ESXi 5.1 update 1 recovery Image?
Hi all
Does anyone know if the R610 is compatible with the recovery Image VMware ESXi 5.1 update 1? It is not on the compatibility list, but the r.620 is there. We use two servers in our VMWare environment and I want to upgrade to 5.1 U1.
Thanks in advance!
Lee
Hi Lee,.
The long wait has its result.
Seems that it's a typo. Engineering has responded that it is supported.
Let me know if you encounter other problems.
-
Driver RAID for Vmware ESXi 5.1 on Dell R420.
My project is to install Vmware ESXi 5.1 on a Dell R420 with Raid1 configuration. The question I have after configuring raid1 in raid utility is created using the, I launch the installation of Vmware ESXi 5.1. What is ESXi 5.1 sees not the raid1 partition but rather see two disks as are they worn can't in raid1 configurations.
I need to have this in raid1 config, can any who share an idea about my problem please or point me in the right direction.
I did some research but nothing seems to help resolve this issue.
Thank you
Sheriff.
Sorry for my previous response:
DELL-Daniel My - when I boot in the BIOS of the controller, I see the raid in a raid1 configuration.
Mgr dev you are right, I did research more when you all answered. I see the PERC S110 pilot was a software raid controller and thus the vmware esxi wouldn't work in a raid configuration 1 (software raid).
Thank you guys for you answer and who helped me
-
VMware ESXi 5.5 - System Board SEL_FULLNESS 0... 100 unknown
Hello community,
I'm going to have that kind of alarm on VMware ESXi 5.5 - SEL_FULLNESS system board 0...
How to solve this problem?
Greetings.
You want to connect to your MMIC and clear log SALT.
Fullness SALT refers to full journal SALT is.
The journal SALT allows only a certain number of entries before becoming full.
Thank you
Kirk...
-
I'm trying to get the BB10 Simulator to work on a VMWare ESXi server. Here's what I've done so far:
- Installed the Simulator on yhe development machine, started VMWare workstation, open the vmx file and downloaded the VM on the ESXi server.
- Disabled 3D acceleration on the machine virtual (on ESX) and selected 'Full touch safe mode' after starting the virtual machine.
At this point, the virtual computer screen displays the IP 'telnet ftp ssh qconn', the axis of the device and the build number.
The next step is to connect the Momentics IDE to this virtual machine.
The Simulator is in need of a vmx file configuration dialog box (likely to run vmware specific commands). In the configuration of ESXi, there is no vmx file.
If I try to connect to the virtual machine by IP address, I need a device password, I did not.
Someone at - it suggestions on what do I do now?
In response to my own question because I found the answer:
Now that I have the IP address, I just follow the steps described in
Because I had never set up a password for the Simulator, I left the empty password field.
Copy-paste the details:
Of your IDE
-Right click on your project in the Project Explorer
-Go to Blackberry tools and click on configure target...
-Click Add new target it... button and enter the IP address of your Simulator in the host name or IP address field, enter your password if you have one then click on finish
To run your application on the Simulator:
-In the Project Explorer view, double click on file bar - descriptor.xml, then click on chip Debug Set button to set the author of the application information.
-Set the configuration of the correct version for the Simulator first by right-clicking on your project and selecting Configurations of Build > Set Active > 4 Simulator-Debug.
-In the Project Explorer view, right-click the project and select build project.
-Right click on the project again, and then select run as > BlackBerry Application C/C++.
-
To install Vmware Esxi 4 on PowerEdge 2800
Hello. I have a PowerEdge 2800. I wanted to install Esxi 4.
I download the OM_6.5.0_SMTD_A0.iso and the server starts on the DVD. When I choose install Vmware Esxi 4.0, it asks me to insert the CD / DVD with. But when I insert the DVD the Vmware I download refuses to recognize. Please help me solve the problem. I even tried to install windows server 2008, he refuses.
Tank you.
I saw the solution.
I was supposed to download "VMware-VMvisor-install". Dell_Customized.ISO' to 'http://ftp.dell.com/esg%20solutions/ '.
Tank you.
-
Hello
Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750. I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-
src-dst-ip port-channel load-balance
Interface Port-channel15
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface GigabitEthernet1/0/15
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth share SRR-queue 10 70 25 5
form of bandwidth SRR-queue 10 0 0 0
priority queue
MLS qos trust dscp
spanning tree portfast
channel-protocol lacp
active in mode channel-group 15
!
interface GigabitEthernet1/0/16
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth share SRR-queue 10 70 25 5
form of bandwidth SRR-queue 10 0 0 0
priority queue
MLS qos trust dscp
spanning tree portfast
channel-protocol lacp
active in mode channel-group 15
!
interface GigabitEthernet1/0/17
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth share SRR-queue 10 70 25 5
form of bandwidth SRR-queue 10 0 0 0
priority queue
MLS qos trust dscp
spanning tree portfast
channel-protocol lacp
active in mode channel-group 15
!
interface GigabitEthernet1/0/18
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth share SRR-queue 10 70 25 5
form of bandwidth SRR-queue 10 0 0 0
priority queue
MLS qos trust dscp
spanning tree portfast
channel-protocol lacp
active in mode channel-group 15
!
interface GigabitEthernet1/0/19
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth share SRR-queue 10 70 25 5
form of bandwidth SRR-queue 10 0 0 0
priority queue
MLS qos trust dscp
spanning tree portfast
channel-protocol lacp
active in mode channel-group 15
!
interface GigabitEthernet1/0/20
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth share SRR-queue 10 70 25 5
form of bandwidth SRR-queue 10 0 0 0
priority queue
MLS qos trust dscp
spanning tree portfast
channel-protocol lacp
active in mode channel-group 15
Currently I see many MAC beat in the log of the switch. From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP. I'm worried about the impact this might have on the CPU / switch.
August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15
August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17
August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20
August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15
Is it by design, if so can I disable the message? If this isn't the case, please can you advise where I can check/change the configuration?
Thank you
Peter
It is really gud who... .you mentioned your solution here.
Can you please mark this question as answered, thatâ so it can help the other guys.
Concerning
Please rate if this can help.
-
Problem with the start of VMware ESXi 5.0
I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror. I went through and completed the installation of VMware ESXi 5.0 on this server. When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN. Instead, I get this text string after the initial boot sequence that is shown in the attachment. I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0. Thank you! Paul
Hi Paul,.
Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below. If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.
Let me know if it helps.
-
I installed VMware ESXi on my Cisco's UCS server but after that I don't get from CIMC.
I installed VMware ESXi on my Cisco's UCS server but after that I don't get from CIMC. also, I am unable to ping the address IP of CIMC. Any help?
I think that MMIC does nothing with your ESXi installation... it is OoB management for servers of the UCS.
Check your config MMIC inside the BIOS again.
BR,
Dragan
-
Hi all
I just updated one of my guests with the latest cisco image provided on the vmware website (Vmware-ESXi-5.5.0-2068190-custom-Cisco-5.5.2.3). After the application as an upgrade of the host and then doing a scan against the host in the Update Manager, it shows that ESXi complete update 2 is missing?
I know this is maybe more a problem of vmware, but wanted to see if someone had run into this?
This thank you for the quick response.
-
OpenManage for VMWare ESXi has no possibility of tasks of virtual disk
OMSA v 7.1 and 7.2 for Windows (and earlier versions) allow the user to perform many tasks on virtual disks, including reconfiguring - expand a RAID array with a new drive.
This is not true for managing open for VMWare ESXi - although you can monitor the status of the RAID and disks with the browser of the OMSA interface type, you cannot perform tasks - can not even make a high beam Flash.
It is a huge problem, because the PERC controllers (H700 and H800, for example) don't allow you to develop virtual using hard drives not Dell disks when you try this during startup in the bios. (These controllers only allows you to create new virtual disks using drives not Dell).
This test was conducted using the latest firmware (12.10.4 - 0001 A10) and drivers for the H700 and H800 and multi-server r610 ESXi 5.1.
Other people with VMWare have been affected by the present? The only solution is to have two player networks connected to the computer, and create a simple Windows with OMSA, boot in Windows Server to expand the table using OMSA for Windows.
I would be interested in the comments of others, including those of Dell. We spent hours on the phone with Dell; This seems to be the only solution. (Yes, Dell released a firmware version last year that has ceased blocking non Dell readers, but it only works for the creation of a new virtual disk, do not expanding one existing).
Yes. It came through a discussion in the Dell | Servers | Discussion of the RAID community.
en.Community.Dell.com/.../20263442.aspx
There is a CD bootable linux called OMSA Live that you download from PowerEdge (linux OS) systems management.
This OMSA PERC H700 and H800 control and allows you to do everything. When you reconfigure the RAID and the PERC card starts the reconstruction, although it seems risky, you can restart under VMware and the reconstruction of the RAID continues on. And you can analyze with OMSA for VMware.
-
I want to download the update of VMware ESxi 5.5 3B
But when I sign up for the trial, it puts me update 2 :-(
What you've recorded for earlier? This happens when you download the other than approved for products product/updates.
Same error for me, but I downloaded the recording with the new code. I think that you will need to register with the new code.
VMware KB: How to download VMware products and troubleshooting issues with downloads
VMware KB: VMware ESXi 5.5, Patch ESXi550-Update03: ESXi 5.5 full update 3
-
Hello
have trouble when I first updated my signature single vCenter Server and later update my vSphere hosts?
A vCenter Server Version 5.5.0U3b should be able to manage vSphere Host Version 5.5.0 GA, right?
Kind regards
Roland
The vCenter Server 5.5 update 3 b can manage VMware ESXi ESX release GA to 5.5 5.5 update 3 b, take a look: VMware product interoperability Matrices
BUT, according to the interoperability matrices and vCenter Server 5.5 update 3 release notes, VMware strongly recommends you upgrade your hosts to 5.5 update 3 b, see:
What's new
- Update Support for the SSLv3 Protocol is disabled by default
Note: In your vSphere environment, you must update vCenter Server vCenter Server 5.5 update 3 b before the update to 5.5 ESXi ESXi update 3 b. vCenter Server will not be able to manage 3B ESXi 5.5 update, if you update ESXi before update vCenter Server to version 5.5 update 3 b. For more information about the sequence in which vSphere environments must be updated, see KB 2057795.
- VMware strongly recommends you update ESXi hosts to ESXi 5.5 update 3 b management of vCenter Server 5.5 updated 3B.
VMware does not recommend the reactivation of SSLv3 because of the vulnerability of POODLE. If all you must enable SSLv3, you must activate the SSLv3 Protocol for all components. For more information, see.- Resolved issues. This version of vCenter Server 5.5 update 3 b solves the problems that have been documented in the resolved issues section.
- Update Support for the SSLv3 Protocol is disabled by default
Maybe you are looking for
-
Several pcie-8371. An undetected
Hello I have two USRP-2943Rs, two of the PCIe x 4 (PCIe-8371) expansion cards and computer host computer. I have two PCI ports on the host to connect these expansion cards in: a 4 x and 16 x. Ironically, the jury of plugged into the x 16 slot works
-
Error code: 80070570 (cannot install updates)
I get an error code 80070570, wil not let me put to update or install the new updates window, there are 2 that I need update.what can do to get rid of the problem
-
my windows xp does not load when they are on the homepage and the bios pass
I am running windows xp sp3 and when I turn on my computer it will not go any father than the bios and the homepage, it just keep coming back to this, I have no recovery disk, is it possible to do without if I can run a scan or even restore, thank yo
-
Try to install Adobe Reader PDF in Windows 7 Professional 64 bit. Get the error 1500 "another current installation". Verify that the use of the Task Manager and the CPU is 0%, no other task running. Any ideas?
-
Nov8th, 2009 I think I need to update my display drivers for my Nvidia PNY Quadro FX 4800 graphics card is honored in XP Mode in Win 7 64 bit? I say this because all displayed and similar gradients look pixel-e and have no gradient, they are levels o