VPN Client 4.8 use/needs in bandwidth

Similar Questions

• AnyConnect VPN client can be used for IPSec remote access VPN connection?

  I think I heard it somewhere that AnyConnect VPN can be used for connections SSLvpn IPSec VPN. Is this possible? Thank you!

  No, the Anyconnect software cannot be used to establish the framework for a VPN IPSEC IKE.

• How to match tunnel-group with auth ASA 8.2 and IPSec VPN Client using digital certificates with Microsoft CA

  Hello

  I set up a lab for RA VPN with a version of the ASA5510 8.2 and VPN Client 5 software using digital certificates with Microsoft CA on a Windows 2003 server. I did the configuration based on this document from Cisco's Web site:

  http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a0080930f21.shtml

  Now, the vpn works fine, but now I need to configure a tunnel-different groups so I can provide different services to different users. The problem I have now is that I don't know how to set it up for the certificate is the name of tunnel-group. If I do an ASA debug crypto isakmp I get this error message:

  % ASA-713906 7: IP = 165.98.139.12, trying to find the group through OR...
  % 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group via IKE ID...
  % 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group via IP ADDR...
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group using default group...
  % ASA-713906 7: IP = 165.98.139.12, connection landed on tunnel_group DefaultRAGroup

  So, basically, when using certificates I connect always VPN RA only with the group default DefaultRAGroup. Do I have to use a model of different web registration for application for a certificate instead of the user model? How can I determine the OU on the user certificate so that match tunnel-group?

  Please help me!

  Kind regards

  Fernando Aguirre

  You can use the group certificate mapping feature to map to a specific group.

  This is the configuration for your reference guide:

  http://www.Cisco.com/en/us/partner/docs/security/ASA/asa82/configuration/guide/IKE.html#wp1053978

  And here is the command for "map of crypto ca certificate": reference

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/C5.html#wp2186685

  Hope that helps.

• Global VPN Client for Apple

  I've recently deployed a SonicWALL NSA2600 and have implemented a VPN site-to site both group WAN VPN that work properly. I distributed global vpn client for users who need access to network resources. However, a user uses exclusively based Apple operating systems. Y at - it a customer vpn global for Apple, or is the app of choice? If there is no other choice, this mobile app will work for a desktop Apple computer?

  Thank you

  Jason

  This link is more accurate for MacOS.

  Installation and use NetExtender on MacOS:

  

• Cisco VPN client with internet

  Hello

  I have a big problem, we have implemented Cisco VPN client to connect to outside to our internal servers. My problem is that all users access to the internet while using the Cisco VPN client. We use the split tunneling, but still all VPN clients access the internet. An advisor to prevent access to the internet through VPN client.

  Thank you

  You said earlier that you allow split tunnel. Are you still doing that?

  We would need to see all of the VPN configuration - including access lists or objects referenced - to provide comprehensive advice.

• Through a PIX VPN client

  Hello

  It seems to me having confused TAC with this question:

  I have a client who has two firewalls PIX 501. One in DC (pix - a) and one in San Diego (pix - b). They are both connected via a static IPSec VPN. Works fine, no problem. I also set up two of them to accept connections from Cisco VPN Clients for these people who are on the road a bit. It also seems to work in most situations.

  However, when you try to connect to one of these two firewalls with the Cisco VPN Client when I'm behind other PIX (resembling a third party site that is not attached to a pix - a or pix - b by all means of transport), establishes the tunnel, but I can't move the traffic to the Remote LAN. At first I thought it was due to the NAT on my home PIX (pix - c). Then, I tried to work, behind a PIX who don't use NAT (pix - d) and got the same results. I should mention that trundle making IPSec is enabled on pix - c and pix - d.

  Establishes the VPN connection very well from outside pix - c or pix - d. I can connect and ping perfectly.

  I thought this would be a simple "oh yes, this turns ' or"this is is not supported", but the TAC engineer who picked up my case does not seem to grasp the concept, nor understand how to read my .gif image of visio four firewalls PIX drawn in the exact scenario described above.

  Thank you

  evt

  What version of IOS is there on pix - a, pix - b?

  What game of transformation for vpn clients do you use?

  In all cases, you must enable NAT traversal on pix - a, pix - b.

• Using Cisco VPN Client in Windows 7 Professional 64 bit

  Hi all!
  I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem

  Open the XP VM itself, do not use the shortcut that was published in
  the W7 boot menu. You need to install Outlook / your email client
  Inside the virtual machine, as well as on the side of W7. You can point to the same
  PST files if you have local PST files, but you just can't open them in
  at the same time of W7 and XP VM.

  There is no way to bridge using the shortcut of publishing app

  Some people have reported success with the third party IPSec
  replacements as customer universal shrew or the NCP. Your IT Department.
  would like to know if these are supported

  :

  > Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
  Barb Bowman www.digitalmediaphile.com

• Using VPN Client coming out behind a PIX

  As I understand it, a PIX can operate as a VPN endpoint for IPsec tunnels, or allow IPsec traffic to pass to the other endpoints behind him; My PIX is an end point, but there are a few users who wish to use the VPN Client to connect to outside points beyond the firewall.

  Is it possible to configure a PIX to two pass through IPsec traffic AND be an endpoint?

  On a related note, two customer software VPN hosts can connect to each other?

  Thank you

  Marc

  My pix company does exactly what you posted, there is lan - lan vpn, and we again establish vpn to other companies via a software vpn client.

  concerning the transmission of described video, it should not need additional acl or configuration assuming that there is no acl on the pix. a question must be noticed is that the other end (i.e. the end point of the remote vpn client) needs to nat-traversal since the local pix usually perform nat/pat.

  However, the vpn directly between two clients is not feasible as its name suggests (they are the two client).

• Need help configuration IOS IPsec to enable communication between the VPN client

  Hi, I need help with the configuration of IPsec VPN router 2811. I want to allow communication between VPN clients, is that possible? I know that ASA, you can do this by using the command "permit same-security-traffic intra-interface".

  The fact is that each Client IP communicator installed, but when they tried to call each other, he failed. I guess that's because the connectivity between them is not permitted because of the VPN connection.

  Thanks in advance...

  Hello

  Try this: -.

  local pool IP 192.168.1.1 ippool 192.168.1.5

  access-list 1 permit host 192.168.1.2< vpn="" ip="" addr="" of="" client="">

  access-list 1 permit host 192.168.1.3< vpn="" ip="" addr="" of="" client="">

  access-list 1 permit 10.10.10.0 0.0.0.255

  < lan="" behind="" the="">

  ISAKMP crypto client configuration group vpnclient

  key cisco123

  ACL 1< binding="" the="" acl="">

  !

  --------Done-------------

  If you do NAT on the router then you might want to exempt your VPN traffic to be NAt had

  Assuming that the NAT of your router is

  overload of IP nat inside source list 111 interface FastEthernet1/0

  !

  ! - The access list is used to specify which traffic

  ! - must be translated to the outside Internet.

  access-list 111 deny ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 111 deny ip 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255

  Above two statements are exempt from nat traffic.

  access-list 111 allow ip 10.10.10.0 0.0.0.255 any<, permits="">

  I would like to know if it worked for you.

  Concerning

  M

• Different classes using Cisco VPN Client VPN

  Hello

  on a cisco ASA 5510, I defined a vpn group used for remote teleworkers who have access to the entire LAN using Cisco VPN Client 4.8.

  I would give to others of this client, but I need to limit their access to LAN resources, which means that I have to have two types of users:

  Remote LAN access

  access to only certain IP addresses

  Both must use the Cisco VPN client.

  How can I do?

  Thank you

  This link should help.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080641a52.shtml

• Unable to connect using the Cisco VPN client

  Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

  I enclose the relevant configuration information in the attachment. Any help is welcome.

  Depending on the version, add...

  ISAKMP nat-traversal

  or

  ISAKMP nat-traversal crypto

  Should be all you need.

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• Need help with configuration on cisco vpn client settings 1941

  Hey all,.

  I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...

  If anyone can help with orders?

  I need the installation:

  user names, authentication group etc.

  Thank you!

  Take a peek inside has the below examples of config - everything you need: -.

  http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html

  HTH >

  Andrew.

• How to check if the address pool is used by the vpn client

  Hello world

  I need config anyconnect VPN on ASA existing who also owns the remote VPN client running.

  Under the ASDM when I click the address pools

  I see two address pools

  Pooldefault that I can see is used by vpn distance courses.

  PoolX - this subnet is not assigned to the user now.

  Is there a way I can check if PoolX subnet is configured to assign the IP address to the remote VPN?

  Concerning

  MAhesh

  Hello

  On the CLI, you could check the output of

  See establishing group policy enforcement

  and

  See the tunnel-group race

  to see if the PoolX is used nowhere in the VPN configurations.

  Of course, you can also just simply look for the configuration and see if there is anything else than the current configuration of the PoolX on the SAA.

  See the race | PoolX Inc.

  This should probably display only the command "ip local pool ' if the address pool has just been created but is not used anywhere.

  -Jouni

• 6500 IOS router Cisco VPN Client using DHCP no Pool of IP

  Hey guys,.

  I have a little trouble trying to get my vpn client to use a dhcp server rather than the pool of intellectual property.  When I use the command IP pool everything works fine, but when I use the dhcp command I get an error on the client-side saying that no address private IP was affected by the peer.

  Here is my config.

  connection of AAA VPNCLIENT_AUTHEN group local RADIUS authentication

  local VPNCLIENT_AUTHOR AAA authorization network

  Configuration group customer isakmp crypto VPNCLIENT_GROUP

  xxxxxxxxxxxxxxxxxxxxxxxxxx key

  DNS 172.25.128.43 172.25.65.43

  win 172.25.1.54

  sktnhr.ca field

  172.25.0.27 DHCP server

  GIADDR DHCP 172.25.205.1

  DHCP timeout 10

  pool # VPNCLIENT_IPPOOL

  Crypto isakmp ISAKMP_PROFILE profile

  VRF HUB_VRF

  match of group identity VPNCLIENT_GROUP

  list of authentication of client VPNCLIENT_AUTHEN

  VPNCLIENT_AUTHOR of ISAKMP authorization list.

  client configuration address respond

  crypto dynamic-map DYN_MAP 1020

  game of transformation-ESP-AES-256-SHA

  ISAKMP_PROFILE Set isakmp-profile

  market arriere-route

  card crypto HUB_CRYPTO_MAP 6005-isakmp dynamic ipsec DYN_MAP

  local IP VPNCLIENT_IPPOOL 172.25.205.25 pool 172.25.205.250

  I can see the dhcp request and offer on my dhcp server but nothing is for the customer.  When I use a pool I ping the dhcp server, which makes me think the roads are okay.  Anyone has any ideas.

  You need the giaddr in an EasyVPN server configuration.  Try adding looping to your switch and test it again.  If you use an iVRF, make sure that the closure is in the VRF and the interface to the server.