VPN client, ip local pool & mask
Hello
I use cisco with a 7206VXR vpn client.
I set up a "local ip pool" that gives us the ip address for each connected client.
The pool is set up like this:
pool of IP local pool-Z 10.3.1.1 10.3.1.254
and we use it like this:
Configuration group customer crypto isakmp ZHANG
key AKEY
pool pool-Z
ACL ACL - Z
The problem I have is that we get an IP with a 8 mask but the mask I want to use should be 16.
Where I specify the network mask?
Thank you
Hi Benoit
You must specify the NETWORK mask in client configuration group
Configuration group customer crypto isakmp ZHANG
key AKEY
pool pool-Z
ACL ACL - Z
subnet mask 255.255.0.0
M.
Hope that the rates of assistance if she
Tags: Cisco Security
Similar Questions
-
Problem Cisco VPN Client with local authentication
I configured PIX for the Cisco VPN client for remote access. It must be connected and also inside network is accessible. It is without any authentication username. It works well with a vpngroup name and the password for the vpngroup, configured on PIX and also on the Cisco VPN client. (version 4.6)
When I configure crypto for local authentication, it did not work. configuration is as follows.
#crypto card: name of the map of local authentication client
I created a user with private = 15.
Client VPN must be connected, and then it pops up a window user name and password. After giving these details. The user is not authenticated.
Are there patterns more to do in / isakmp / ipsec / aaa configurations.
Thank you
AAA-server local LOCAL Protocol
client authentication card crypto remote_vpn LOCAL
client configuration address card crypto remote_vpn throw
client configuration address card crypto remote_vpn answer
-
VPN clients are unable to access internal resources
Hello
I have problems with internal resources from access to the content of VPN Clients. They connect using Cisco VPN Client, they connect correctly, an IP address from the correct range is given and I ping to the internal server, but any other type of access as Server terminal server. Ping to server ip from the inside is answered by interface router public ip instead of the internal server and I don't know if it's this way. There isn't any ACL applied.
Crypto ipsec debugging I see this error when I do the server terminal server:
% CRYPTO-4-RECVD_PKT_NOT_IPSEC: Rec'd package not an IPSEC packet. (ip) vrf/adr_dest = / public-ip, src_addr = 172.16.73.4, prot = 6
Here is the configuration associated with vpn:
crypto ISAKMP policy 10
BA aes 256
preshared authentication
Group 2
!
Configuration group customer isakmp crypto VPN_Clients
Cisco key
DNS 4.2.2.2
pool - vpn clients
ACL 101
netmask 255.255.255.0
!
!
Crypto ipsec transform-set RIGHT aes - esp esp-sha-hmac
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
market arriere-route
!
!
card crypto mymap client authentication list userlist
Group card crypto mymap isakmp authorization list
client configuration address map mymap crypto initiate
client configuration address map mymap crypto answer
map mymap 10-isakmp ipsec crypto dynamic dynmap
!
!
! Gateway for the default internal resources
interface Vlan72
IP 172.16.72.1 255.255.255.0
no ip proxy-arp
IP nat inside
IP virtual-reassembly
!
Kind regards.
VPN client IP local pool 172.16.73.2 172.16.73.10
!
!
interface Dialer1
the negotiated IP address
IP mtu 1492
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 1
Authentication callin PPP chap Protocol
PPP chap hostname XXXXX
PPP chap password 7 XXXXXXXX
accept dns ipcp PPP
PPP ipcp address accept
No cdp enable
crypto mymap map
access-list 101 permit ip 172.16.72.0 0.0.0.255 any
!
Hi Anotino,
Problem seems to be with the NAT configuration on the router. The NAT config is now below:
access-list 1 permit 172.16.72.0 0.0.0.255
NAT_WAN1 allowed 10 route map
corresponds to the ip address 1
match interface Dialer1
IP nat inside source overload map route NAT_WAN1 interface Dialer1
We need to change it to look like this:
access-list 100 deny ip 172.16.72.0 0.0.0.255 172.16.73.0 0.0.0.255
access-list 100 permit ip 172.16.72.0 0.0.0.255 any
NAT_WAN1 allowed 10 route map
corresponds to the IP 100
IP nat inside source overload map route NAT_WAN1 interface Dialer1
This should make sure to go to the pool of clients VPN traffic United Nations concerns and therefore, you should be able to access the network using the private IP (172.16.72.2 for example).
Try this and tell me if this solves your problem.
Kind regards
Assia
Post edited by: Assia Ramamoorthy small correction in the post!
-
Can the NAT of ASA configuration for vpn local pool
We have a group of tunnel remote ipsec, clients address pool use 172.18.33.0/24 which setup from command "ip local pool. The remote cliens must use full ipsec tunnel.
Because of IP overlap or route number, we would like to NAT this local basin of 172.18.33.0 to 192.168.3.0 subnet when vpn users access certain servers or subnet via external interface of the ASA. I have nat mapping address command from an interface to another interface of Armi. The pool local vpn is not behind any physical interface of the ASA. My question is can ASA policy NAT configuration for vpn local pool. If so, how to set up this NAT.
Thank you
Haiying
Elijah,
NAT_VPNClients ip 172.18.33.0 access list allow 255.255.255.0 10.1.1.0 255.255.255.0
public static 192.168.33.0 (external, outside) - NAT_VPNClients access list
The above configuration will be NAT 172.18.33.0/24 to 192.168.33.0/24 when you go to 10.1.1.0/24 (assuming that 10.1.1.0/24 is your subnet of servers).
To allow the ASA to redirect rewritten traffic the same interface in which he receive, you must also order:
permit same-security-traffic intra-interface
Federico.
-
How to check if the address pool is used by the vpn client
Hello world
I need config anyconnect VPN on ASA existing who also owns the remote VPN client running.
Under the ASDM when I click the address pools
I see two address pools
Pooldefault that I can see is used by vpn distance courses.
PoolX - this subnet is not assigned to the user now.
Is there a way I can check if PoolX subnet is configured to assign the IP address to the remote VPN?
Concerning
MAhesh
Hello
On the CLI, you could check the output of
See establishing group policy enforcement
and
See the tunnel-group race
to see if the PoolX is used nowhere in the VPN configurations.
Of course, you can also just simply look for the configuration and see if there is anything else than the current configuration of the PoolX on the SAA.
See the race | PoolX Inc.
This should probably display only the command "ip local pool ' if the address pool has just been created but is not used anywhere.
-Jouni
-
6500 IOS router Cisco VPN Client using DHCP no Pool of IP
Hey guys,.
I have a little trouble trying to get my vpn client to use a dhcp server rather than the pool of intellectual property. When I use the command IP pool everything works fine, but when I use the dhcp command I get an error on the client-side saying that no address private IP was affected by the peer.
Here is my config.
connection of AAA VPNCLIENT_AUTHEN group local RADIUS authentication
local VPNCLIENT_AUTHOR AAA authorization network
Configuration group customer isakmp crypto VPNCLIENT_GROUP
xxxxxxxxxxxxxxxxxxxxxxxxxx key
DNS 172.25.128.43 172.25.65.43
win 172.25.1.54
sktnhr.ca field
172.25.0.27 DHCP server
GIADDR DHCP 172.25.205.1
DHCP timeout 10
pool # VPNCLIENT_IPPOOL
Crypto isakmp ISAKMP_PROFILE profile
VRF HUB_VRF
match of group identity VPNCLIENT_GROUP
list of authentication of client VPNCLIENT_AUTHEN
VPNCLIENT_AUTHOR of ISAKMP authorization list.
client configuration address respond
crypto dynamic-map DYN_MAP 1020
game of transformation-ESP-AES-256-SHA
ISAKMP_PROFILE Set isakmp-profile
market arriere-route
card crypto HUB_CRYPTO_MAP 6005-isakmp dynamic ipsec DYN_MAP
local IP VPNCLIENT_IPPOOL 172.25.205.25 pool 172.25.205.250
I can see the dhcp request and offer on my dhcp server but nothing is for the customer. When I use a pool I ping the dhcp server, which makes me think the roads are okay. Anyone has any ideas.
You need the giaddr in an EasyVPN server configuration. Try adding looping to your switch and test it again. If you use an iVRF, make sure that the closure is in the VRF and the interface to the server.
-
ASA VPN cannot ping ip local pool
Hello
We have ASA 5510 a device be deployed for a period of time. Everything works fine except customers local VPN cannot ping local customer VPN which get their IP address to the local swimming pool. They can ping anywhere on the local network of company, but not each other. I don't know there's a logical explantion for this because of an ACL but all appreciated the advice...
Thanks in advance
Keith
Hi Keith,
I think that, in order to allow a customer VPN reach another VPN client, the SAA should turn the VPN traffic (because it will receive the traffic of a VPN tunnel and re - again to send another tunnel.)
Can you add "same-security-traffic intra-interface permits" and try again?
Federico.
-
VPN - PC (vpn client) problem-> router-> (site to site vpn)-> local network
Hello
is it possible to install?
I have a pc and I want to connect to the Remote LAN.
PC (using vpn client) - vpn (internet)---> ROUTER1 - a vpn (MPLS network)---> ROUTER2---> SERVER site
How can I connect to a remote server? Is there an easy way?
I did the configuration of the vpn client (I can connect ROUTER1 and access a LAN via vpn with 192.168.1.x), but I can't connect to the server, even if I set the subnet (192.168.1.x) under the access list of site to site vpn (access list for traffic that must pass between ROUTER1 and ROUTER2).
Please advise! Thanks in advance.
Looks like I've not well explained.
On ROUTER1
===================
1 ACL VNC_acl is used to split tunnel, so you should include IP server_NET it NOT vpn IP pool.
2 ACL najavorbel is used to set the lan lan traffic between ROUTER1 and ROUTER2, 2 you should inlcude
IP 192.168.133.0 allow 0.0.0.255 0.0.0.255
You must change the crypto ROUTER2 ACL of the minor or the najavorbel of the ACL
The other way to is to the client VPN NAT IP to a local area network lan IP ROUTER1, in this way, you don't need any changes on ROUTER2. But I have to take a look at your configuration to make the suggestion.
-
We are testing the upgrade to version 8.2 to 8.4 on the ASA 5505 and ran into a problem. For VPN connections, we created pools. Some of the pools were limited to a single IP address. After the upgrade, the ASA rejects the pools which had only an IP address instead of a range. In the command line if you type a question mark after typing in the "local ip pool (pool keyword)' in config mode it says" specify an IP address or a range of IP addresses: start [-end] ' by the word 'or' sounds as it should, except a single IP address, but it doesn't. The error is "Please enter a valid IP range."
Does anyone know the soultion to this problem as well as increase the range?
Thanks for your comments.
The syntax below worked for me on 5505 with ver 8.3
test mask 192.168.10.1 IP 255.255.255.255 local pool
Check if it works for you.
HTH
MS
-
How to allow access to a local area network behind the cisco vpn client
Hi, my question is about how to allow access to a local area network behind the cisco vpn client
With the help of:
- Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
- Cisco VPN Client version 5.0 software
Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?
Thank you.
Hi Vladimir,.
Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.
If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.
-
Installation of VM with VPN client access to the network local provents
What is the best approach for the connection to the VPN in the following scenario?
We want to install VM for our projects as VPN client networking (using the cisco vpn client). In many cases the VPN profile that is configured by the client is configured to prevent access to the local network, but rather the tunnels all through the VPN.
I tried the NAT and Bridged networks and once you connect to the VPN client, the conectitivy of the virtual machine is limited to the VMWare console. SSH and other connections no longer work.
Thanks for any idea.
I'd VNC - that's what I use for a VM XP that uses the client VPN SecuRemote CheckPoint blocking the same way (wisely) off incoming traffic when the connection is made to the other end of the VPN.
Just paste lines similar to the following in your .vmx file when the virtual machine is shut down:
RemoteDisplay.vnc.enabled = TRUE
RemoteDisplay.vnc.port = '5910 '.
RemoteDisplay.vnc.password = 'somepassword '.
RemoteDisplay.vnc.keymap = 'uk '.Note that you point your VNC client software on the IP address (and port of your .vmx file) to your server 2.0, not the virtual machine host. Use a different port for each computer virtual you need simultaneous to access.
-
Cisco VPN Client cannot ping from LAN internal IP
Hello
I apologize in advance for my lack of knowledge about it, but I got a version of the software running ASA 5510 7.2 (2) and has been invited to set up a site with a client, I managed to get this configured and everything works fine. In addition, I created a group of tunnel ipsec-ra for users to connect to a particular server 192.168.10.100/24 remote, even if the connection is made successfully, I can not ping any IP on the LAN 192.168.10.0/24 located behind the ASA and when I ping inside the interface on the ASA it returns the public IP address of the external interface.
If someone out there could give me a little push in the right direction, it would be much appreciated! This is the current configuration of the device.
Thanks in advance.
: Saved
:
ASA Version 7.2 (2)
!
hostname ciscoasa5510
domain.local domain name
activate the password. 123456789 / encrypted
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group ISP
12.34.56.789 255.255.255.255 IP address pppoe setroute
!
interface Ethernet0/1
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
management only
!
passwd encrypted 123456789
passive FTP mode
clock timezone GMT/UTC 0
summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS server-group DefaultDNS
domain.local domain name
permit outside_20_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124
access-list Split_Tunnel_List note the network of the company behind the ASA
Split_Tunnel_List list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
IP local pool domain_vpn_pool 192.168.11.1 - 192.168.11.254 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 522.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 12.34.56.789 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
internal domain_vpn group policy
attributes of the strategy of group domain_vpn
value of 212.23.3.100 DNS server 212.23.6.100
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Split_Tunnel_List
username domain_ra_vpn password 123456789 encrypted
username domain_ra_vpn attributes
VPN-group-policy domain_vpn
encrypted utilisateur.123456789 password username
encrypted utilisateur.123456789 password username
privilege of username user password encrypted passe.123456789 15
encrypted utilisateur.123456789 password username
the ssh LOCAL console AAA authentication
AAA authentication enable LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map 20 set pfs
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto outside_map 20 match address outside_20_cryptomap
peer set card crypto outside_map 20 987.65.43.21
outside_map crypto 20 card value transform-set ESP-3DES-SHA
3600 seconds, duration of life card crypto outside_map 20 set - the security association
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
aes-256 encryption
sha hash
Group 5
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
tunnel-group 987.65.43.21 type ipsec-l2l
IPSec-attributes tunnel-group 987.65.43.21
pre-shared-key *.
tunnel-group domain_vpn type ipsec-ra
tunnel-group domain_vpn General-attributes
address domain_vpn_pool pool
Group Policy - by default-domain_vpn
domain_vpn group of tunnel ipsec-attributes
pre-shared-key *.
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 5
Console timeout 0
VPDN group ISP request dialout pppoe
VPDN group ISP localname [email protected] / * /
VPDN group ISP ppp authentication chap
VPDN username [email protected] / * / password *.
dhcpd dns 212.23.3.100 212.23.6.100
dhcpd lease 691200
dhcpd ping_timeout 500
domain.local domain dhcpd
!
dhcpd address 192.168.10.10 - 192.168.10.200 inside
dhcpd allow inside
!
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:1234567890987654321
: end
Hello
Seems to me that you are atleast lack the NAT0 configuration for your VPN Client connection.
This configuration is intended to allow the VPN Client to communicate with the local network with their original IP addresses. Although the main reason that this is necessary is to avoid this traffic to the normal rule of dynamic PAT passing this traffic and that traffic is falling for the corresponding time.
You can add an ACL rule to the existing ACL NAT0, you have above and the NAT configuration should go next
Add this
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
Hope this helps
Let me know how it goes
-Jouni
-
VPN site to site & outdoor on ASA 5520 VPN client
Hi, I'm jonathan rivero.
I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.
the executed show.
ASA1 (config) # sh run
: Saved
:
ASA Version 8.0 (2)
!
hostname ASA1
activate 7esAUjZmKQSFDCZX encrypted password
names of
!
interface Ethernet0/0
nameif inside
security-level 100
address 172.16.3.2 IP 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 200.20.20.1 255.255.255.0
!
interface Ethernet0/1.1
VLAN 1
nameif outside1
security-level 0
no ip address
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/5
Shutdown
No nameif
no level of security
no ip address
!
2KFQnbNIdI.2KYOU encrypted passwd
passive FTP mode
object-group, net-LAN
object-network 172.16.0.0 255.255.255.0
object-network 172.16.1.0 255.255.255.0
object-network 172.16.2.0 255.255.255.0
object-network 172.16.3.0 255.255.255.0
object-group, NET / remote
object-network 172.16.100.0 255.255.255.0
object-network 172.16.101.0 255.255.255.0
object-network 172.16.102.0 255.255.255.0
object-network 172.16.103.0 255.255.255.0
object-group network net-poolvpn
object-network 192.168.11.0 255.255.255.0
access list outside nat extended permit ip net local group object all
access-list extended sheep allowed ip local object-group net object-group net / remote
access-list extended sheep allowed ip local object-group net net poolvpn object-group
access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group
pager lines 24
Within 1500 MTU
Outside 1500 MTU
outside1 MTU 1500
IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 100 burst-size 10
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 access list outside nat
Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1
Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
!
!
internal vpngroup1 group policy
attributes of the strategy of group vpngroup1
banner value +++ welcome to Cisco Systems 7.0. +++
value of 192.168.0.1 DNS server 192.168.1.1
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value splittun-vpngroup1
value by default-ad domain - domain.local
Split-dns value ad - domain.local
the address value ippool pools
username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15
tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared-key *.
type tunnel-group vpngroup1 remote access
tunnel-group vpngroup1 General-attributes
ippool address pool
Group Policy - by default-vpngroup1
vpngroup1 group of tunnel ipsec-attributes
pre-shared-key *.
context of prompt hostname
Cryptochecksum:00000000000000000000000000000000
: end
ASA2 (config) #sh run
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
VPNL2L interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared key ciscomy topology:
I try with the following links, but did not work
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml
http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml
Best regards...
"" I thing both the force of the SAA with the new road outside, why is that? ".
without the road ASA pushes traffic inward, by default.
In any case, this must have been a learning experience.
Hopefully, this has been no help.
Please rate, all the helful post.
Thank you
Rizwan Muhammed.
-
Windows - Internet access, no split Tunnel L2TP VPN Clients does not
Greetings!
I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.
I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.
Here is the configuration:
: Saved
:
ASA Version 1.0000 11
!
SGC hostname
domain somewhere.com
names of
COMMENTS COMMENTS LAN 192.168.2.0 name description
name 75.185.129.13 description of SGC - external INTERNAL ASA
name 172.22.0.0 description of SITE1-LAN Ohio management network
description of SITE2-LAN name 172.23.0.0 Lake Club Network
name 172.24.0.0 description of training3-LAN network Southwood
description of training3 - ASA 123.234.8.124 ASA Southwoods name
INTERNAL name 192.168.10.0 network Local INTERNAL description
description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
description of Apollo name 192.168.10.4 INTERNAL domain controller
description of DHD name 192.168.10.2 Access Point #1
description of GDO name 192.168.10.3 Access Point #2
description of Odyssey name 192.168.10.5 INTERNAL Test Server
CMS internal description INTERNAL ASA name 192.168.10.1
name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
description of training3-VOICE name Southwood Voice Network 10.1.0.0
name 172.25.0.0 description of training3-WIFI wireless Southwood
!
interface Vlan1
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan2
nameif INSIDE
security-level 100
255.255.255.0 SGC-internal IP address
!
interface Vlan3
nameif COMMENTS
security-level 50
IP 192.168.2.1 255.255.255.0
!
interface Ethernet0/0
Time Warner Cable description
!
interface Ethernet0/1
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/2
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/4
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/5
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/6
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/7
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
boot system Disk0: / asa821-11 - k8.bin
Disk0: / config.txt boot configuration
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS domain-lookup outside
INTERNAL DNS domain-lookup
DNS domain-lookup GUEST
DNS server-group DefaultDNS
Name-Server 4.2.2.2
domain somewhere.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
the DM_INLINE_NETWORK_1 object-group network
network-object SITE1-LAN 255.255.0.0
network-object SITE2-LAN 255.255.0.0
network-object training3-LAN 255.255.0.0
object-group training3-GLOBAL network
Southwood description Global Network
network-object training3-LAN 255.255.0.0
network-object training3-VOICE 255.255.0.0
network-object training3-WIFI 255.255.0.0
DM_INLINE_TCP_2 tcp service object-group
EQ port 5900 object
EQ object Port 5901
object-group network INTERNAL GLOBAL
Description Global INTERNAL Network
network-object INTERNAL 255.255.255.0
network-object INTERNALLY-VPN 255.255.255.0
access-list outside_access note Pings allow
outside_access list extended access permit icmp any CMS-external host
access-list outside_access note that VNC for Camille
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
access-list outside_access note INTERNAL Services
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
no pager
Enable logging
exploitation forest asdm warnings
Debugging trace record
Outside 1500 MTU
MTU 1500 INTERNAL
MTU 1500 COMMENTS
192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 623.bin
enable ASDM history
ARP timeout 14400
Global 1 interface (outside)
(INTERNAL) NAT 0 access-list sheep
NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
NAT (GUEST) 1 0.0.0.0 0.0.0.0
5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
Access-group outside_access in interface outside
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol AAA-server Apollo
Apollo (INTERNAL) AAA-server Apollo
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
Enable http server
http 0.0.0.0 0.0.0.0 INTERNAL
http 0.0.0.0 0.0.0.0 COMMENTS
No snmp server location
No snmp Server contact
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
correspondence address 1 card crypto outside_map INTERNAL SITE1
card crypto outside_map 1 set of peer SITE1 - ASA
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
address for correspondence card crypto outside_map 2 INTERNAL training3
outside_map 2 peer training3 - ASA crypto card game
card crypto outside_map 2 game of transformation-ESP-3DES-SHA
address for correspondence outside_map 3 card crypto INTERNAL SITE2
game card crypto outside_map 3 peers SITE2 - ASA
card crypto outside_map 3 game of transformation-ESP-3DES-SHA
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
delimiter group @.
Telnet training3 - ASA 255.255.255.255 outside
Telnet SITE2 - ASA 255.255.255.255 outside
Telnet SITE1 - ASA 255.255.255.255 outside
Telnet 0.0.0.0 0.0.0.0 INTERNAL
Telnet 0.0.0.0 0.0.0.0 COMMENTS
Telnet timeout 60
SSH enable ibou
SSH training3 - ASA 255.255.255.255 outside
SSH SITE2 - ASA 255.255.255.255 outside
SSH SITE1 - ASA 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 INTERNAL
SSH 0.0.0.0 0.0.0.0 COMMENTS
SSH timeout 60
Console timeout 0
access to the INTERNAL administration
Hello to tunnel L2TP 100
interface ID client DHCP-client to the outside
dhcpd dns 4.2.2.1 4.2.2.2
dhcpd ping_timeout 750
dhcpd outside auto_config
!
address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
dhcpd Apollo Odyssey interface INTERNAL dns
dhcpd somewhere.com domain INTERNAL interface
interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
enable dhcpd INTERNAL
!
dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
enable dhcpd COMMENTS
!a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 192.43.244.18 prefer external source
WebVPN
allow outside
CSD image disk0:/securedesktop-asa-3.4.2048.pkg
SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
enable SVC
Group Policy DefaultRAGroup INTERNAL
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
Group Policy DefaultWEBVPNGroup INTERNAL
attributes of Group Policy DefaultWEBVPNGroup
VPN-tunnel-Protocol webvpn
Group Policy DefaultL2LGroup INTERNAL
attributes of Group Policy DefaultL2LGroup
Protocol-tunnel-VPN IPSec l2tp ipsec
Group Policy DefaultACVPNGroup INTERNAL
attributes of Group Policy DefaultACVPNGroup
VPN-tunnel-Protocol svc
attributes of Group Policy DfltGrpPolicy
value of 192.168.10.4 DNS Server 4.2.2.2
VPN - 25 simultaneous connections
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
the value INTERNAL VPN address pools
chip-removal-disconnect disable card
WebVPN
SVC keepalive no
client of dpd-interval SVC no
dpd-interval SVC bridge no
value of customization DfltCustomization
attributes global-tunnel-group DefaultRAGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultRAGroup
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
Disable ISAKMP keepalive
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
attributes global-tunnel-group DefaultWEBVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultWEBVPNGroup
tunnel-group 123.234.8.60 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.60
pre-shared-key *.
tunnel-group 123.234.8.124 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.124
pre-shared-key *.
tunnel-group 123.234.8.189 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.189
pre-shared-key *.
type tunnel-group DefaultACVPNGroup remote access
attributes global-tunnel-group DefaultACVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultACVPNGroup
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
inspect the they
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
: end
ASDM image disk0: / asdm - 623.bin
ASDM location Camille 255.255.255.255 INTERNAL
ASDM location INTERNAL CGT-external 255.255.255.255
ASDM location INTERNAL SITE1-LAN 255.255.0.0
ASDM location INTERNAL SITE2-LAN 255.255.0.0
ASDM location INTERNAL training3-LAN 255.255.0.0
ASDM location INTERNAL training3 - ASA 255.255.255.255
ASDM location INTERNAL GDO 255.255.255.255
ASDM location INTERNAL SITE1 - ASA 255.255.255.255
ASDM location INTERNAL SITE2 - ASA 255.255.255.255
ASDM location INTERNAL training3-VOICE 255.255.0.0
ASDM location puppy 255.255.255.255 INTERNAL
enable ASDM historyI should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.
You must configure * intercept-dhcp enable * in your group strategy:
attributes of Group Policy DefaultRAGroup
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.comIntercept-dhcp enable
-Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked. It is located on the Advanced tab of VPN client TCP/IP properties. Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.
Alex
-
ASA Anyconnect VPN do not work or download the VPN client
I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config
XXXX # sh run
: Saved
:
ASA Version 8.4 (3)
!
hostname XXXX
search for domain name
activate pFTzVNrKdD9x5rhT encrypted password
zPBAmb8krxlXh.CH encrypted passwd
names of
!
interface Ethernet0/0
Outside-interface description
switchport access vlan 20
!
interface Ethernet0/1
Uplink DMZ description
switchport access vlan 30
!
interface Ethernet0/2
switchport access vlan 10
!
interface Ethernet0/3
switchport access vlan 10
!
interface Ethernet0/4
Ganymede + ID description
switchport access vlan 10
switchport monitor Ethernet0/0
!
interface Ethernet0/5
switchport access vlan 10
!
interface Ethernet0/6
switchport access vlan 10
!
interface Ethernet0/7
Description Wireless_AP_Loft
switchport access vlan 10
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif outside
security-level 0
IP address x.x.x.249 255.255.255.248
!
Vlan30 interface
no interface before Vlan10
nameif dmz
security-level 50
IP 172.16.30.1 255.255.255.0
!
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS domain-lookup dmz
DNS server-group DefaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
search for domain name
network obj_any1 object
subnet 0.0.0.0 0.0.0.0
network of the Webserver_DMZ object
Home 172.16.30.8
network of the Mailserver_DMZ object
Home 172.16.30.7
the object DMZ network
172.16.30.0 subnet 255.255.255.0
network of the FTPserver_DMZ object
Home 172.16.30.9
network of the Public-IP-subnet object
subnet x.x.x.248 255.255.255.248
network of the FTPserver object
Home 172.16.30.8
network of the object inside
192.168.10.0 subnet 255.255.255.0
network of the VPN_SSL object
10.101.4.0 subnet 255.255.255.0
outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer to 8192
logging trap warnings
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 647.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
NAT (exterior, Interior) static source VPN_SSL VPN_SSL
!
network obj_any1 object
NAT static interface (indoor, outdoor)
network of the Webserver_DMZ object
NAT (dmz, outside) static x.x.x.250
network of the Mailserver_DMZ object
NAT (dmz, outside) static x.x.x.. 251
the object DMZ network
NAT (dmz, outside) static interface
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede HNIC +.
AAA-server host 192.168.10.2 HNIC (inside)
Timeout 60
key *.
identity of the user by default-domain LOCAL
Console HTTP authentication AAA HNIC
AAA console HNIC ssh authentication
Console AAA authentication telnet HNIC
AAA authentication secure-http-client
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ca trustpoint localtrust
registration auto
Configure CRL
Crypto ca trustpoint VPN_Articulate2day
registration auto
name of the object CN = vpn.articulate2day.com
sslvpnkey key pair
Configure CRL
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 30
SSH 192.168.10.0 255.255.255.0 inside
SSH timeout 15
SSH version 2
Console timeout 0
No vpn-addr-assign aaaDHCP-client update dns
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd outside auto_config
!
dhcpd address 192.168.10.100 - 192.168.10.150 inside
dhcpd allow inside
!
dhcpd address dmz 172.16.30.20 - 172.16.30.23
dhcpd enable dmz
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
authenticate the NTP
NTP server 192.168.10.2
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal VPN_SSL group policy
VPN_SSL group policy attributes
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_SplitTunnel
the address value VPN_SSL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 15
AnyConnect ssl deflate compression
AnyConnect ask enable
ronmitch50 spn1SehCw8TvCzu7 encrypted password username
username ronmitch50 attributes
type of remote access service
type tunnel-group VPN_SSL_Clients remote access
attributes global-tunnel-group VPN_SSL_Clients
address VPN_SSL pool
Group Policy - by default-VPN_SSL
tunnel-group VPN_SSL_Clients webvpn-attributes
enable VPNSSL_GNS3 group-alias
type tunnel-group VPN_SSL remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect esmtp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: endXXXX #.
You do not have this configuration:
object network DMZ nat (dmz,outside) static interface
Try and take (or delete):
object network DMZ nat (dmz,outside) dynamic interface
Maybe you are looking for
-
i mac OSX10-9-5 2015. How can I order i-Tunes DOES NOT close automatically after 30 minutes... Despite having put in place to save energy to stay active for 2 hours?
-
I can't access online Halifax (my Bank) more. I can if I use IE.
I enter my user name and password in the Halifax page online (https://www.halifax-online.co.uk/personal/logon/login.jsp) as usual and click on the continue"" button. Nothing happens! Absolutely nothing. If I do exactly the same thing in IE then it wo
-
I'd like to if it's in the menu options...
I'm sorry if this isn't the right place to say this, but I like it if the authorization manager has been in the Options menu, I've written a bug a few weeks for it to be added there and he won't if good, overall it has been a pain to try to get what
-
Windows 7 64 Bit update error Code 8E5E03FE
I just bought a new PC running Windows 7 64 bit and made my first run updates of Windows very well, that everything installed OK. Then, most of the updates and everything I try they fail with "Error 8E5E03FE", help on Windows itself is absolutely use
-
How to uninstall a specific Windows Live Essentials program
2 type appwiz.cpl , and then press enter3. look for Windows Live Essentials and click on Change/Remove4. Select Uninstall , and then click continue5 follow the instructions on the screen I did, but it did not work... its does not give me the opportun