VPN ipsec active on both WAN ports?

Hi guys, we VPN works on WAN1 and we WAN2 as a failover. IF WAN1 breaks down, then we can vpn to ip of backup.

Is it possible to have active VPN on the two networks at the same time? Then users can choose to use WAN2, if they think that the main connection WAN1 is too slow?

Thank you

Hello

If it's a C2S, then it is not possible according to my knowledge... because the traffic is going to come back with the route by default... option... so it would be impossible in my opinion... If it's a S2S, then you have a static route to do with...

Concerning

Knockaert

Tags: Cisco Security

Similar Questions

IPsec site2sitevpn and DMVPN on a single WAN port

Hi Experts,

can you please it is possible to use IPsec site2sitevpn and DMVPN on WAN port unique until I apply the two vpn on a single wan link connection please give your comments it's ok or not.

Thanks in advance,

ciscolearner

Hello

Yes you can, there is no conflict. I just tested and confirmed in a laboratory.

Kind regards

Tim

Please don't forget to rate helpful messages and mark the answers accurate.

VPN ipsec and port 500

Hello world

I connected connection VPN IPSEC.

Connection works fine.

Here's the Setup program

PC---R1---R2--R3---ISP---ASA

I check on R3

The R3 CBAC is configured.

R3 # sh ip inspect sessions | 96.51.x.x Inc.
65719DB4 (192.168.98.6:59936)-online (96.51.x.x:4500) SIS_OPEN udp session

What vpn ipsec connection is established, it shows that it is plugged into the port 4500 not 500?

What is default behavior?

Initially when he formed theVPN connection it showed both udp, ports 500 and 4500.

Concerning

MAhesh

It has NAT/PAT between R3 and ASA. like address (192.168.98.6) private IP allows you to configure the ipsec session. IKE detects NAT/PAT exist in NAT - D payload. IKE uses UDP 4500 to negotiate ISAKMP rather than UDP 500. Subsequently, the ESP traffic is also encapsulated in UDP 4500, in this way it can cross the NAT/PAT safely.

If this behavior is expected.

GRE tunnels will not come on VPN IPsec/GRE

Hi all

We have 400 + remote sites that connect to our central location (and a backup site) using Cisco routers with vpn IPSec/GRE tunnels. We use a basic model for the creation of tunnels, so there is very little chance of a bad configuration on each router. Remote sites use Cisco 831 s, central sites use Cisco 2821 s. There is a site where the tunnels WILL refuse just to come.

Routers are able to ping their public IP addresses, so it is not a routing problem, but gre endpoints cannot ping. There is no NATing involved, two routers directly accessing the Internet. The assorded display orders seem to indicate that the SAs are properly built, but newspapers, it seems that last part just don't is finished, and the GRE tunnels come not only upward.

The attached log file, it seems that both its IPSEC & ISAKMP are created @ 00:25:14, then QM_PHASE2 end @ 00:25:15.

00:25:15: ISAKMP: (0:10:HW:2): node error 1891573546 FALSE reason for deletion "(wait) QM.
00:25:15: ISAKMP: (0:10:HW:2): entrance, node 1891573546 = IKE_MESG_FROM_PEER, IKE_QM_EXCH
00:25:15: ISAKMP: (0:10:HW:2): former State = new State IKE_QM_R_QM2 = IKE_QM_PHASE2_COMPLETE
00:25:15: ISAKMP (0:268435467): received 208.XX packet. Dport 500 sport Global 500 (I) QM_IDLE yy.11

00:25:15: IPSEC (key_engine): had an event of the queue with 1 kei messages
00:25:15: IPSEC (key_engine_enable_outbound): rec would prevent ISAKMP
00:25:15: IPSEC (key_engine_enable_outbound): select SA with spinnaker 1572231461/50
00:25:15: ISAKMP: (0:11:HW:2): error in node-1931380074 FALSE reason for deletion "(wait) QM.
00:25:15: ISAKMP: (0:11:HW:2): entrance, node-1931380074 = IKE_MESG_FROM_PEER, IKE_QM_EXCH
00:25:15: ISAKMP: (0:11:HW:2): former State = new State IKE_QM_R_QM2 = IKE_QM_PHASE2_COMPLETE
00:25:15: IPSEC (key_engine): had an event of the queue with 1 kei messages
00:25:15: IPSEC (key_engine_enable_outbound): rec would prevent ISAKMP
00:25:15: IPSEC (key_engine_enable_outbound): select SA with spinnaker 310818168/50

I don't have the remote router log file, and is very long, so I joined her. Before that I captured the log file, I enabled debugging ipsec & isakmp and immediately authorized the SAs.

Assorted useful details and matching orders of show results:

Cisco IOS Software, C831 (C831-K9O3SY6-M), Version 12.4 (25), RELEASE SOFTWARE (fc1)

There are 2 connections of IPSEC/GRE tunnel:

Tunnel101: KC (208.YY. ZZ.11) - remote control (74.WW. XX.35)
Tunnel201: Dallas (208.XX. YY.11) - remote control (74.WW. XX.35)

Site-382-831 #sho ip int br
Interface IP-Address OK? Method State Protocol
FastEthernet1 unassigned YES unset down down
FastEthernet2 unassigned YES unset upward, upward
FastEthernet3 unassigned YES unset upward, upward
FastEthernet4 unassigned YES unset upward, upward
Ethernet0 10.3.82.10 YES NVRAM up up
Ethernet1 74.WW. XX.35 YES NVRAM up up
Ethernet2 172.16.1.10 YES NVRAM up up
Tunnel101 1.3.82.46 YES NVRAM up toward the bottom<>
Tunnel201 1.3.82.62 YES NVRAM up toward the bottom<==== ="">
NVI0 unassigned don't unset upward upwards

Site-382-831 #.
Site-382-831 #sho run int tunnel101
Building configuration...

Current configuration: 277 bytes
!
interface Tunnel101
Description % connected to the 2nd KC BGP 2821 - PRI - B
IP 1.3.82.46 255.255.255.252
IP mtu 1500
IP virtual-reassembly
IP tcp adjust-mss 1360
KeepAlive 3 3
source of tunnel Ethernet1
destination of the 208.YY tunnel. ZZ.11
end

Site-382-831 #.

Site-382-831 #show isakmp crypto his
status of DST CBC State conn-id slot
208.XX. YY.11 74.WW. XX.35 QM_IDLE ASSETS 0 11
208.YY. ZZ.11 74.WW. XX.35 QM_IDLE 10 0 ACTIVE
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show detail of the crypto isakmp
Code: C - IKE configuration mode, D - Dead Peer Detection
NAT-traversal - KeepAlive, N - K
X - IKE extended authentication
PSK - GIPR pre-shared key - RSA signature
renc - RSA encryption

C - id Local Remote I have VRF status BA hash Auth DH lifetime limit.
11 74.WW. XX.35 208.XX. YY.11 ACTIVE 3des sha psk 1 23:56:09
Connection-id: motor-id = 11:2 (hardware)
74.WW 10. XX.35 208.YY. ZZ.11 ACTIVE 3des sha psk 1 23:56:09
Connection-id: motor-id = 10:2 (hardware)
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show crypto ipsec his

Interface: Ethernet1
Tag crypto map: IPVPN_MAP, local addr 74.WW. XX.35

protégé of the vrf: (none)
ident (addr, mask, prot, port) local: (74.WW. XX.35/255.255.255.255/47/0)
Remote ident (addr, mask, prot, port): (208.YY. ZZ.11/255.255.255.255/47/0)
current_peer 208.YY. ZZ.11 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: 2333, #pkts encrypt: 2333, #pkts digest: 2333
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
#send 21, #recv errors 0

local crypto endpt. : 74.WW. XX.35, remote Start crypto. : 208.YY. ZZ.11
Path mtu 1500, mtu 1500 ip, ip mtu IDB Ethernet1
current outbound SPI: 0x45047D1D (1157922077)

SAS of the esp on arrival:
SPI: 0x15B97AEA (364477162)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: C83X_MBRD:4, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4486831/1056)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

the arrival ah sas:

SAS of the CFP on arrival:

outgoing esp sas:
SPI: 0x45047D1D (1157922077)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: C83X_MBRD:3, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4486744/1056)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

outgoing ah sas:

outgoing CFP sas:

protégé of the vrf: (none)
ident (addr, mask, prot, port) local: (74.WW. XX.35/255.255.255.255/47/0)
Remote ident (addr, mask, prot, port): (208.XX. YY.11/255.255.255.255/47/0)
current_peer 208.XX. YY.11 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: 2333, #pkts encrypt: 2333, #pkts digest: 2333
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
#send 21, #recv errors 0

local crypto endpt. : 74.WW. XX.35, remote Start crypto. : 208.XX. YY.11
Path mtu 1500, mtu 1500 ip, ip mtu IDB Ethernet1
current outbound SPI: 0xE82A86BC (3895101116)

SAS of the esp on arrival:
SPI: 0x539697CA (1402378186)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2008, flow_id: C83X_MBRD:8, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4432595/1039)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

the arrival ah sas:

SAS of the CFP on arrival:

outgoing esp sas:
SPI: 0xE82A86BC (3895101116)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2001, flow_id: C83X_MBRD:1, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4432508/1039)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

outgoing ah sas:

outgoing CFP sas:
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show crypto ipsec his | Pkts Inc. | life
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4486831/862)
calendar of his: service life remaining (k/s) key: (4486738/862)
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4432595/846)
calendar of his: service life remaining (k/s) key: (4432501/846)
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show crypto isakmp policy

World IKE policy
Priority protection Suite 10
encryption algorithm: three key triple a
hash algorithm: Secure Hash Standard
authentication method: pre-shared Key
Diffie-Hellman group: #1 (768 bits)
lifetime: 86400 seconds, no volume limit
Default protection suite
encryption algorithm: - Data Encryption STANDARD (56-bit keys).
hash algorithm: Secure Hash Standard
authentication method: Rivest-Shamir-Adleman Signature
Diffie-Hellman group: #1 (768 bits)
lifetime: 86400 seconds, no volume limit
Site-382-831 #.

Site-382-831 #show crypto card
"IPVPN_MAP" 101-isakmp ipsec crypto map
Description: at the 2nd KC BGP 2821 - PRI - B
Peer = 208.YY. ZZ.11
Extend the PRI - B IP access list
access list PRI - B allowed will host 74.WW. XX.35 the host 208.YY. ZZ.11
Current counterpart: 208.YY. ZZ.11
Life safety association: 4608000 Kbytes / 3600 seconds
PFS (Y/N): N
Transform sets = {}
IPVPN,
}

"IPVPN_MAP" 201-isakmp ipsec crypto map
Description: 2nd Dallas BGP 2821 - s-B
Peer = 208.XX. YY.11
Expand the list of IP SEC-B access
s - B allowed will host 74.WW access list. XX.35 the host 208.XX. YY.11
Current counterpart: 208.XX. YY.11
Life safety association: 4608000 Kbytes / 3600 seconds
PFS (Y/N): N
Transform sets = {}
IPVPN,
}
Interfaces using crypto card IPVPN_MAP:
Ethernet1
Site-382-831 #.

Tunnel between KC & the remote site configuration is:

Distance c831 - KC

crypto ISAKMP policy 10
BA 3des
preshared authentication
!
PRI-B-382 address 208.YY isakmp encryption key. ZZ.11
!
Crypto ipsec transform-set esp-3des esp-sha-hmac IPVPN
transport mode
!
IPVPN_MAP 101 ipsec-isakmp crypto map
Description of 2nd KC BGP 2821 - PRI - B
set of peer 208.YY. ZZ.11
game of transformation-IPVPN
match address PRI - B
!
interface Tunnel101
Description % connected to the 2nd KC BGP 2821 - PRI - B
IP 1.3.82.46 255.255.255.252
IP mtu 1500
KeepAlive 3 3
IP virtual-reassembly
IP tcp adjust-mss 1360
source of tunnel Ethernet1
destination of the 208.YY tunnel. ZZ.11
!
interface Ethernet0
private network Description
IP 10.3.82.10 255.255.255.0
IP mtu 1500
no downtime
!
interface Ethernet1
IP 74.WW. XX.35 255.255.255.248
IP mtu 1500
automatic duplex
IP virtual-reassembly
card crypto IPVPN_MAP
no downtime
!
PRI - B extended IP access list
allow accord 74.WW the host. XX.35 the host 208.YY. ZZ.11
!

KC-2821 *.

PRI-B-382 address 74.WW isakmp encryption key. XX.35
!
PRI-B-382 extended IP access list
allow accord 208.YY the host. ZZ.11 the host 74.WW. XX.35
!
IPVPN_MAP 382 ipsec-isakmp crypto map
Description % connected to the 2nd KC BGP 2821
set of peer 74.WW. XX.35
game of transformation-IPVPN
match address PRI-B-382
!
interface Tunnel382
Description %.
IP 1.3.82.45 255.255.255.252
KeepAlive 3 3
IP virtual-reassembly
IP tcp adjust-mss 1360
IP 1400 MTU
delay of 40000
tunnel of 208.YY origin. ZZ.11
destination of the 74.WW tunnel. XX.35
!
end

Any help would be much appreciated!

Mark

Hello

logs on Site-382-831, only see the crypt but none decrypts, could you check a corresponding entry on the peer and see if has any questions send return traffic?

Site-382-831 #show crypto ipsec his | Pkts Inc. | life
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4486831/862)
calendar of his: service life remaining (k/s) key: (4486738/862)
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4432595/846)
calendar of his: service life remaining (k/s) key: (4432501/846)
Site-382-831 #.

Kind regards

Averroès.

VPN IPSEC on Metro-Elba

Hi all

I have a small question. Is it possible to run L2L IPSEC VPN via a subway-E connection? It's not supposed to do something like that with Metro-E but this connection is with a partner so at both ends, firewall is in place. With port forwading, NATting, etc, etc, I came across problems of providing additional services because of it. I hope that IPSEC VPN L2L at both ends will solve this problem once and for all. The only question is of course in fact that a metro-E is just an ethernet connection and not really difference in setting up a VPN IPSEC of L2L via internet.

Thank you for your help.

Eric,

Yes, connection L2L IPSEC VPN Tunnel Over Metro-E should work perfectly. You might meet in the treatment of air issues and the flow on the VPN server but it should be good.

Kind regards

Arul

* Rate pls if it helps *.

VPN IPSEC between two networks

Hello-

For these last days, I've been banging my head against the wall with this problem.

I have two IP networks that have the same IP that I need to create an IPSEC tunnel between.

Here's a crude diagram:

192.168.1.0/24--[Cisco 1920] - Internet-[cisco RV082]--192.168.1.0/24

I know that I should make some sort of NAT, but from what I've been through the RV082 it's not like he can do it.

I tried to get this work is this:

192.168.1.0/24--[Cisco 1920] - Internet-[cisco RV082]-192.168.33.0/24-[Belkin N300 consumer router]--192.168.1.0/24

But once I changed LAN IP of Belkin 192.168.1.1/24 I lost connectivity to the "WAN" port, I was clicking on the side LAN of 1920. (I think he was trying to route the traffic via the LAN port is even if it is entered on its WAN port)

Someone has some tips to get me going in the right direction?

Thank you

Greg Smythe

Hi Greg,.

If you have same subnet on both ends, then Yes you are right the NAT is the only option. You need to do NAT on both devices. As you say that RV is unable to do so I don't think that if you have any othe roption to change the subnet on one of the end. Which is not an easy option

Thank you

Jeet

Cisco's VPN IPSec client for LAN connectivity

I've looked through further discussions and were not able to find a clear answer on this, so I apologize if this is a duplicate question.

I have the client setup Cisco VPN on an ASA 5505 with tunneling split. I can connect to the VPN very well. I can access the internet fine. I can't get the LAN, however. I try to do a ping, telnet, rdp, etc devices on the side LAN of the firewall without a bit of luck. I have torn down and configure the VPN several times via the CLI and I even used various configurations by using the wizard, all this without a bit of luck. Any help would be appreciated.

ASA Version 8.2 (2)

!

hostname spp-provo-001-fwl-001

domain servpro.local

activate the F7n9M1BQr1HPy/zu encrypted password

F7n9M1BQr1HPy/zu encrypted passwd

no names

name 10.0.0.11 Exch-Srv

name 10.0.0.12 DRAC

name 10.0.0.10 DVR

!

interface Vlan1

nameif inside

security-level 100

the IP 10.0.0.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

ServPro PPPoE client vpdn group

IP address pppoe setroute

!

interface Vlan12

nameif Guest_Wireless

security-level 90

IP 10.10.0.1 address 255.255.255.0

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

switchport access vlan 12

!

exec banner * only authorized access *.

exec banner * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

connection of the banner * only authorized access *.

connection of the banner * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

banner asdm * only authorized access *.

banner asdm * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

boot system Disk0: / asa822 - k8.bin

passive FTP mode

clock timezone STD - 7

clock to summer time recurring MDT

DNS lookup field inside

DNS server-group DefaultDNS

10.0.0.11 server name

Name-Server 8.8.8.8

domain servpro.local

DRACServices tcp service object-group

EQ port 5900 object

EQ object of the https port

EQ object Port 5901

object-group service Exch-SrvServices tcp

EQ port 587 object

port-object eq 993

port-object eq www

EQ object of the https port

port-object eq imap4

EQ Port pop3 object

EQ smtp port object

SBS1Services tcp service object-group

EQ port 3389 object

port-object eq www

EQ object of the https port

EQ smtp port object

outside_access_in list extended access permit tcp any host *. *. *. * object-group SrvServices Exch

outside_access_in list permits all icmp access *. *. *. * 255.255.255.248

capture a whole list of access allowed icmp

Servpro_splitTunnelAcl list standard access allowed 10.0.0.0 255.255.255.0

inside_nat0_outbound to access ip 10.0.0.0 scope list allow 255.255.255.0 172.16.10.0 255.255.255.240

inside_nat0_outbound list of allowed ip extended access any 172.16.10.0 255.255.255.240

guest_wireless_in list extended access permitted tcp a whole

guest_wireless_in of access allowed any ip an extended list

NO_NAT to access ip 10.0.0.0 scope list allow 255.255.255.0 10.10.0.0 255.255.255.0

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

MTU 1500 Guest_Wireless

mask 172.16.10.1 - 172.16.10.14 255.255.255.240 IP local pool ServProDHCPVPN

no failover

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 625.bin

don't allow no asdm history

ARP timeout 14400

NAT-control

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 0.0.0.0 0.0.0.0

NAT (Guest_Wireless) 1 0.0.0.0 0.0.0.0

static (inside, outside) *. *. *. * 10.0.0.11 netmask 255.255.255.255

Access-group outside_access_in in interface outside

Access-group guest_wireless_in in the Guest_Wireless interface

Route outside 0.0.0.0 0.0.0.0 *. *. *. * 2 track 2

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

AAA-server Exch-Srv Protocol nt

AAA-server Exch-Srv (inside) host 10.0.0.11

Timeout 5

auth-NT-PDC SRV EXCH

the ssh LOCAL console AAA authentication

AAA authentication LOCAL telnet console

AAA authentication http LOCAL console

LOCAL AAA authentication serial console

Enable http server

http server idle-timeout 10

http 10.0.0.0 255.255.255.0 inside

http 0.0.0.0 0.0.0.0 outdoors

redirect http outside 80

redirect http inside 80

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

monitor SLA 124

type echo protocol ipIcmpEcho 4.2.2.2 outside interface

NUM-package of 3

frequency 10

Annex monitor SLA 124 life never start-time now

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint ASDM_TrustPoint0

registration auto

name of the object CN = cisco.spprovo.com

ServPro key pair

Configure CRL

string encryption ca ASDM_TrustPoint0 certificates

certificate f642be4b

308202fc 308201e4 a0030201 020204f6 42be4b30 0d06092a 864886f7 0d 010105

311a 3018 05003040 06035504 03131163 6973636f 2e737070 726f766f 2e636f6d

31223020 06092 has 86 01090216 13636973 636f2e73 726f2e6c 65727670 4886f70d

6f63616c 31303034 30383230 35363232 30303430 35323035 5a170d32 301e170d

3632325a 3040311a 30180603 55040313 and 11636973 636f2e73 7070726f 766f2e63

6f6d3122 30200609 2a 864886 f70d0109 02161363 6973636f 2e736572 7670726f

2e6c6f63 616c 3082 0122300d 06092 has 86 01010105 00038201 0f003082 4886f70d

010a 0282 010100 has 5 b4646cde f981f048 efa54c8a 4ba4f51c 25471e01 459ea905

313ef490 72b4d853 4e95ab7d a8c1350e 5728dca6 a98c439e 2c12d219 06ee7209

9f2584d1 b2abf71c 31c0890f 3098533b 6bc3ad4b 3bcd8986 e70ca78e 07a749d6

ee4e0892 4fcb79b6 724f7012 9f42fc2f b80c17ed adb5d36b 67590061 453d9ae6

16583d 36 5a22b7c2 737fd705 94656f3f 578fb67f 79bd2a59 17522be3 d2386e22

2c62352f cda317b0 be805a04 76f19989 34031cbd a5fc62a7 1d9f52f3 00cf60b6

bbbdc4f0 fb651b82 b3e22a0a 718ff0b4 e213f4ac cdeb413b 9c4a47c3 9134d7a9

e8dcf2c5 c1cd4075 61d75e3a 475a17f1 2f955741 9ed2a8d6 c381eba3 247134e1

b5c33fac 7ae03d02 03010001 300 d 0609 2a 864886 05050003 82010100 f70d0101

156 5fde62c5 b4cbb0f4 0c61fab7 fae04399 27457ab7 9790c 3fac914d 70595db9

e69d3f19 3476dc51 32c885de b5904030 05624fe0 e8983e0a ab5527f3 8c5dd64a

1e1a6082 b6091657 8704c 539 a3c6be47 da2a871f 4fafe668 70db2c2b 573d47b2

7f3df02f c9d53a92 bcf5f518 9953e14c f957a6ca 279f9e9f ddbd2561 6e0503c2

ba59a165 055d697f dd028d00 5cc288c4 83ced827 9c82ef3e 7e67f2d2 6de573e3

42a0b6bf ef8d06ed cb9805f2 c38011d3 5263bc3f 5b68df7a bef36c40 8c5e33f3

26b02c27 63a9848c 8461738f cd19ae95 f059ee34 afe4bdbc 8d8d2335 751b 0621

65464b2c 4649779d 3ba01b69 8977 has 790 73815f8b 3c483f93 a5ca9685 04b6e18a

quit smoking

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

No encryption isakmp nat-traversal

!

Track 2 rtr 124 accessibility

Telnet 10.0.0.0 255.255.255.0 inside

Telnet timeout 10

SSH 10.0.0.0 255.255.255.0 inside

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 10

SSH version 2

Console timeout 10

VPDN group ServPro request dialout pppoe

VPDN group ServPro localname *

VPDN group ServPro ppp authentication pap

password username * VPDN * local store

dhcpd outside auto_config

!

dhcpd address 10.10.0.100 - 10.10.0.227 Guest_Wireless

dhcpd dns 8.8.8.8 4.2.2.2 interface Guest_Wireless

enable Guest_Wireless dhcpd

!

a basic threat threat detection

threat detection statistics

a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200

NTP server 38.117.195.101 source outdoors

NTP server 72.18.205.157 prefer external source

SSL-trust outside ASDM_TrustPoint0 point

WebVPN

allow outside

SVC disk0:/anyconnect-win-2.3.0254-k9.pkg 1 image

enable SVC

tunnel-group-list activate

attributes of Group Policy DfltGrpPolicy

Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

Servpro internal group policy

Group Policy attributes Servpro

Server DNS 10.0.0.11 value

Protocol-tunnel-VPN IPSec svc webvpn

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list Servpro_splitTunnelAcl

SERVPRO.local value by default-field

servpro encrypted NtdaWcySmet6H6T0 privilege 15 password username

servpro username attributes

type of service admin

username, encrypted bHGJDrPmHaAZY/78 Integratechs password

tunnel-group Servpro type remote access

attributes global-tunnel-group Servpro

address pool ServProDHCPVPN

authentication-server-group LOCAL Exch-Srv

strategy-group-by default Servpro

tunnel-group Servpro webvpn-attributes

enable ServPro group-alias

IPSec-attributes tunnel-group Servpro

pre-shared key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

inspect the icmp

!

global service-policy global_policy

context of prompt hostname

call-home

Profile of CiscoTAC-1

no active account

http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /

destination-mode http transport

Subscribe to alert-group diagnosis

Subscribe to alert-group environment

Subscribe to alert-group monthly periodic inventory

monthly periodicals to subscribe to alert-group configuration

daily periodic subscribe to alert-group telemetry

Cryptochecksum:52bca254012b1b05cca7dfaa30d1c42a

: end

Most likely you are behind a router PAT when you are connected to the VPN, so please allow the following:

Crypto isakmp nat-traversal 30

Press L2L VPN, IPSEC, and L2TP PIX connections

Hi all

I'm trying to implement a solution on my FW PIX (pix804 - 24.bin) to be able to support a VPN L2L session with VPN dynamic user sessions where clients will use a mix of IPSEC(Nat detection) and L2TP. We have always supported things IPSEC and that worked great for many years. I'm now trying to Add L2TP support, so that I can support Android phones/ipads, etc. as well as Windows with built in VPN l2tp clients clients. Everything works well except for the new features of L2TP. Allows you to complete one phase but then tries to use the card encryption that is used for the VPN L2L. It seems to fail because IP addresses are not in the configured ACL to the crypto-map L2L. Does anyone know if there are any questions all these configurations support both. And if not can you see what I have wrong here, which would make it not work. Here are the relevant training:

C515 - A # sh run crypto
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set of society-ras-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac company-l2tp
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Dynamic crypto map company-ras 1 correspondence address company-dynamic
company Dynamics-card crypto-ras 1 set pfs
Dynamic crypto map company-ras 1 transform-set ESP-SHA-3DES ESP-3DES-MD5 company-ras
Dynamic crypto map company-ras 1 lifetime of security association set seconds 28800
company Dynamics-card crypto-ras 1 kilobytes of life together - the association of safety 4608000
crypto dynamic-map-ras company 2 address company-dynamic game
crypto dynamic-map company-ras 2 transform-set of society-l2tp
crypto dynamic-map company-ras 2 set security association lifetime seconds 28800
company Dynamics-card crypto-ras 2 kilobytes of life together - the association of safety 4608000
card crypto company-map 1 correspondence address company-colo
card crypto company-card 1 set pfs
card crypto company-card 1 set counterpart colo-pix-ext
card crypto card company 1 value transform-set ESP-3DES-MD5 SHA-ESP-3DES
company-map 1 lifetime of security association set seconds 28800 crypto
card company-card 1 set security-association life crypto kilobytes 4608000
company-card 1 set nat-t-disable crypto card
company-card 2 card crypto ipsec-isakmp dynamic company-ras
business-card interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside

Crypto isakmp nat-traversal 3600

crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 2
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
C515 - A # sh run tunnel-group
attributes global-tunnel-group DefaultRAGroup
company-ras address pool
Group-LOCAL radius authentication server
Group Policy - by default-l2tp
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
tunnel-group DefaultRAGroup ppp-attributes
PAP Authentication
No chap authentication
ms-chap-v2 authentication
eap-proxy authentication
type tunnel-group company-ras remote access
tunnel-group global company-ras-attributes
company-ras address pool
Group-LOCAL radius authentication server
tunnel-group company-ras ipsec-attributes
pre-shared-key *.
type tunnel-group company-admin remote access
attributes global-tunnel-group company-admin
company-admin address pool
Group-LOCAL radius authentication server
company strategy-group-by default-admin
IPSec-attributes of tunnel-group company-admin
pre-shared-key *.
PPP-attributes of tunnel-group company-admin
No chap authentication
ms-chap-v2 authentication
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared-key *.
ISAKMP keepalive retry threshold 15 10
C515 - A # sh run Group Policy
attributes of Group Policy DfltGrpPolicy
Server DNS 10.10.10.20 value 10.10.10.21
Protocol-tunnel-VPN IPSec
enable PFS
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value company-SPLIT-TUNNEL-ACL
company.int value by default-field
NAC-parameters DfltGrpPolicy-NAC-framework-create value
internal strategy of company-admin group
attributes of the strategy of company-admin group
WINS server no
DHCP-network-scope no
VPN-access-hour no
VPN - 20 simultaneous connections
VPN-idle-timeout 30
VPN-session-timeout no
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the IP-comp
Re-xauth disable
Group-lock no
enable PFS
Split-tunnel-network-list value company-ADMIN-SPLIT-TUNNEL-ACL
L2TP strategy of Group internal
Group l2tp policy attributes
Server DNS 10.10.10.20 value 10.10.10.21
Protocol-tunnel-VPN l2tp ipsec
disable the PFS
Split-tunnel-policy tunnelall
company.int value by default-field
NAC-parameters DfltGrpPolicy-NAC-framework-create value

Relevant debug output

C515 - Has # Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, Oakley proposal is acceptable
Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall
Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, status of automatic NAT detection: remote endpoint IS behind a NAT device this end is NOT behind a NAT device
Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, previously allocated memory of liberation for permission-dn-attributes
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, PHASE 1 COMPLETED
Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, for this connection Keep-alive type: None
Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, Keep-alives configured on, but the peer does not support persistent (type = None)
Sep 03 02:09:33 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, timer to generate a new key to start P1: 21600 seconds.
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, detected L2TP/IPSec session.
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, QM IsRekeyed its not found old addr
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa181b866).
Sep 03 02:09:33 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, case of mistaken IKE responder QM WSF (struct & 0x501c1f0) , : QM_DONE EV_ERROR--> QM_BLD_MSG2 EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG--> QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH
Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, peer table correlator Removing failed, no match!
Sep 03 02:09:33 [IKEv1]: ignoring msg SA brand with Iddm 204910592 dead because ITS removal
Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, Oakley proposal is acceptable
Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall
Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, status of automatic NAT detection: remote endpoint IS behind a NAT device this end is NOT behind a NAT device
Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, previously allocated memory of liberation for permission-dn-attributes
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, PHASE 1 COMPLETED
Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, for this connection Keep-alive type: None
Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, Keep-alives configured on, but the peer does not support persistent (type = None)
Sep 03 02:10:05 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, timer to generate a new key to start P1: 21600 seconds.
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, detected L2TP/IPSec session.
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, QM IsRekeyed its not found old addr
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa5db9562).
Sep 03 02:10:05 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, case of mistaken IKE responder QM WSF (struct & 0x501c1f0) , : QM_DONE EV_ERROR--> QM_BLD_MSG2 EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG--> QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, peer table correlator Removing failed, no match!
Sep 03 02:10:05 [IKEv1]: ignoring msg SA brand with Iddm 204914688 dead because ITS removal

The outputs of two debugging who worry are the following:

Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701

Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa5db9562).

This seems to indicate that his NAT detection but then do not assign to the entry card cryptography because networks are encrypted are not in the configured ACL that is true. He needs to use dynamic input and it doesn't seem to be.

I need to create another dynamic map entry to make it work instead of add lines to the same dynamic with a lower (higher) priority map entry?

Thanks in advance for any help here.

Hello

That won't do the trick, l2tp clients are picky kindda, so you know if they do not hit the correct strategy first they just stop trying. Follow these steps:

correspondence from the company of dynamic-map crypto-ras 1 address company-dynamic

No crypto-card set pfs dynamic company-ras 1

No crypto dynamic-map company-ras-1 transform-set ESP-SHA-3DES ESP-3DES-MD5 company-ras

Dynamic crypto map company-ras 1 transform-set company-l2tp SHA-ESP-3DES ESP-3DES-MD5 company-ras

The foregoing will not affect existing customers of IPsec at all, these clients will not use the statement of pfs and will link even if the correspondence address is not configured (it is optional), besides Cisco IPsec clients will be affected first the mode of transport policy and fail however they will continue to try and hit another police PH2.

Regarding your last question, I was referring specifically to the support of l2tp for android, and Yes, you will need to run one of these versions.

http://www.Cisco.com/en/us/docs/security/ASA/asa82/release/notes/asarn82.html#wp431562

Tavo-

RV042 Dual WAN Port DMZ not acquire an IP from ISP

Hello

I am trying to replace my router with the more robust RV042 of current load balancing. Installation seems simple enough. However, I am having an issue gets an IP address of the DMZ port in load balancing mode.

The two WAN is the same ISP and is both DSL, using the same models of DSL Modem. #1 WAN port works perfectly.

Indeed, when an independent piece of equipment is installed in the #2 DSL modem, this gives an IP address instantly...

The two DSL lines only require a MAC address to get their IP addresses, and none of the static values are allowed, perhaps to test only.

The issue of intellectual property has been seen before. I can't find any reference to the iton this site.

Thank you

Steve

Glad to hear that it works.

The "save the settings and restart" is not all that rare, although it is not typical for your model.

The obligation of power off is certainly not normal. He told me that some sort of electric lock has occurred. This could be a unique thing, caused by a discharge of static electricity, or it could indicate a manufacturing defect. If this is the first case he did re - is probably. If it is the latter, then it will need a trade at any given time.

In any case, it seems that the MAC address index has been at least partially useful.

Good luck, somone will be here if you need assistance once again.

need help with VPN IPSEC with RV042

https://supportforums.Cisco.com/docs/doc-30883

I enjoy any support for a trial with RV042 VPN IPSec game please.

Thanks in advance.

Hi Bay, if you use a Windows computer, you can use QuickVPN. The only thing to note is the router that you have as the gateway to the RV042. You must define a port forward for all IPsec services be able to overcome the problems with the NAT device.

RV042 configuration is easy, create a name of user and password and that's it. The problem/challenge will get your NAT connection to allow VPN pass.

-Tom
Please mark replied messages useful

Setup for use with Cisco Anyconnect VPN IPsec

So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.

I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.

NOTE: We are still testing this ASA and is not in production.

Any help you can give me is greatly appreciated.

ASA Version 8.4 (2)

!

ASA host name

domain.com domain name

!

interface Ethernet0/0

nameif inside

security-level 100

the IP 192.168.0.1 255.255.255.0

!

interface Ethernet0/1

nameif outside

security-level 0

IP 50.1.1.225 255.255.255.0

!

interface Ethernet0/2

Shutdown

No nameif

no level of security

no ip address

!

interface Ethernet0/3

Shutdown

No nameif

no level of security

no ip address

!

interface Management0/0

No nameif

security-level 100

IP 192.168.1.1 255.255.255.0

!

boot system Disk0: / asa842 - k8.bin

passive FTP mode

DNS domain-lookup outside

DNS server-group DefaultDNS

!

permit same-security-traffic intra-interface

!

network of the NETWORK_OBJ_192.168.0.224_27 object

subnet 192.168.0.224 255.255.255.224

!

object-group service VPN

ESP service object

the purpose of the tcp destination eq ssh service

the purpose of the tcp destination eq https service

the purpose of the service udp destination eq 443

the destination eq isakmp udp service object

!

allowed IP extended ip access list a whole

!

mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool

no failover

failover time-out period - 1

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 645.bin

don't allow no asdm history

ARP timeout 14400

NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary

!

the object of the LAN network

NAT dynamic interface (indoor, outdoor)

Access-group outside_in in external interface

Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1

Sysopt noproxyarp inside

Sysopt noproxyarp outdoors

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec ikev2 ipsec-proposal OF

encryption protocol esp

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 proposal ipsec 3DES

Esp 3des encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES

Esp aes encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES192

Protocol esp encryption aes-192

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 AES256 ipsec-proposal

Protocol esp encryption aes-256

Esp integrity sha - 1, md5 Protocol

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint ASDM_TrustPoint0

registration auto

name of the object CN = ASA

Configure CRL

crypto ca server

Shutdown

string encryption ca ASDM_TrustPoint0 certificates

certificate d2c18c4e

864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105

0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e

365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2

8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b

37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c

234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782

3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02

03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1

cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc

18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6

beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef

af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398

quit smoking

IKEv2 crypto policy 1

aes-256 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 10

aes-192 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 20

aes encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 30

3des encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 40

the Encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

Crypto ikev2 activate out of service the customer port 443

Crypto ikev2 access remote trustpoint ASDM_TrustPoint0

Crypto ikev1 allow outside

IKEv1 crypto policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 65535

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH timeout 10

Console timeout 0

management-access inside

SSL-trust outside ASDM_TrustPoint0 point

WebVPN

allow outside

AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2

AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3

profiles of AnyConnect VPN disk0: / devpn.xml

AnyConnect enable

tunnel-group-list activate

internal VPN group policy

attributes of VPN group policy

value of server WINS 50.1.1.17 50.1.1.18

value of 50.1.1.17 DNS server 50.1.1.18

Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

digitalextremes.com value by default-field

WebVPN

value of AnyConnect VPN type user profiles

always-on-vpn-profile setting

privilege of xxxxxxxxx encrypted password username administrator 15

VPN1 xxxxxxxxx encrypted password username

VPN Tunnel-group type remote access

General-attributes of VPN Tunnel-group

address (inside) VPNPool pool

address pool VPNPool

LOCAL authority-server-group

Group Policy - by default-VPN

VPN Tunnel-group webvpn-attributes

enable VPN group-alias

Group-tunnel VPN ipsec-attributes

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

class-map ips

corresponds to the IP access list

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

Review the ip options

inspect the netbios

inspect the rsh

inspect the rtsp

inspect the skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect the tftp

inspect the sip

inspect xdmcp

inspect the http

class ips

IPS inline help

class class by default

Statistical accounting of user

I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)

Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.

I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.

As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)

Site-to-Site VPN IPSEC falls intermittently

Site-to-Site VPN IPSEC falls intermittently

I am currently having a problem with a VPN from Site to Site traffic not only not intermittently. When the problem occurs, I can't Ping the remote site to the AC Site. But I can solve the problem by Pinging from HQ at the Remote Site. My network is currently configured as follows

-------HQ------

7.0 (4) version of pix 515 with card Ethernet 4 ports.

Outside of the interface connected to the Broadband DSL link.

Outside2 Interface connected to the second link DSL broadband

-Distance-

I have 4 Remote Sites. 2 sites connect you to each connection to wide band at HQ to spread the load to HQ

6.3 (5) pix 501 version

# The problem #.

All VPN establishes successfully to the HQ Pix

Intermittently, a remote site will report that they cannot connect to servers/services in the HQ. When I do a show crypto ipsec's and see the crypto isakmp his headquarters there is no entry for the remote site. However when I do the same on the remote site there is an entry for the HQ. With debugging on the remote site pix I try to ping from a pc to the HQ server and I get the following (see below). If I do a "ipsec Isakmp security association claire crypto ' and ' clear crypto ipsec his ' on the pix of remote site, then I can successfully ping all servers in headquarters.

This problem seems to have taken place only when I upgraded the pix of a 501 to 515 and added another 2 remote sites and a second broadband, as described above. I'm afraid that there is a problem with software version 7 Pix. Any advice would be greatly appreciated.

Console record Carrick-PIX01 (config) # 7

Carrick-PIX01 (config) # ter Lun

Output Carrick-PIX01 (config) #.

Carrick-PIX01 # debug crypto ipsec

Carrick-PIX01 # debug crypto isakmp

Carrick-PIX01 #.

ISAKMP (0:0): sending of NAT - T vendor ID - rev 2 & 3

ISAKMP (0): early changes of Main Mode

ISAKMP (0): retransmission of the phase 1 (0)...

ISAKMP (0): retransmission of the phase 1 (1)...

ISAKMP (0): retransmission of the phase 1 (2)...

Carrick-PIX01 #.

Carrick-PIX01 #.

ISAKMP (0): retransmission of the phase 1 (3)...

Carrick-PIX01 #.

Carrick-PIX01 #.

ISAKMP (0): retransmission of the phase 1 (4)... IPSec (key_engine): request timer shot: count = 1,.

(identity) local = OUTER-IP, distance = 86.43.74.16,.

local_proxy = LAN-OFFICE/255.255.255.0/0/0 (type = 4),

remote_proxy = 194.x.x.x.x.255.0/0/0 (type = 4)

ISAKMP (0): delete SA: CBC EXTERNAL IP, dst 86.43.74.16

ISADB: Reaper checking HIS 0x10c167c, id_conn = 0 DELETE IT!

Peer VPN: ISAKMP: Peer Info for 86.43.74.16/500 not found - peer: 1

ISADB: Reaper checking HIS 0x10ca914, id_conn = 0

Can force you the ISAKMP Keepalive, value from IPSec Security Association idle time and on the other. The problem should be solved

ISAKMP crypto keepalive 30

Crypto ipsec security association temps_inactivite 60

Let me know if it helps

Site to Site VPN IPsec IPv6 on issue of routers-Tunnel

Hi, I am experiencing a problem can any one address the question below and let me know the solution. I have two routers and try to build "Site to Site VPN IPsec IPv6". I followed orders from Cisco and community document but when I apply my profile of ipsec for tunnel interfaces, that the tunnel is down.

https://supportforums.Cisco.com/docs/doc-27009

Ali,

VTI tunnels are meant to be broken when there is no active negotiated spinnakers.

The tunnel will go towards up/face upwards when there is a means of transport of packages - i.e. the SPIs are present.

You can control the order spinnakers 'show peer's crypto ipsec '.

For debugging:

Debug crypto isa

Debug crypto ipsec

M.

Cable modem has no WAN port

I have XFinity for my cable and internet services. We just moved into a house built in 1850 and due to the size of the House and horse hair plaster, upstairs gets very little signal WiFi. I want to extend the reach of WiFi and intended to do with a couple of Airport extreme. The only problem is, every tutorial I watch shows the first Airport Extreme being plugged into the WAN port on the modem cable suppliers. My router/modem, made by Cisco, has no port Ethernet WAN port only 4. Can I connect the Airport Extreme on port 1 and then put in place using the Airport according to normal or need a WAN port?

If you have a modem/router, then you would connect an Ethernet cable from one of the four ports Ethernet LAN <>-... choose any you want, they are all the same... to the "O" on the AirPort Extreme WAN port.

Then use Configuration utility of Apple AirPort "Wizard" to configure AirPort Extreme to create a wireless network that uses the same exact wireless network and the same password that the wireless Cisco uses.

The wizard will apply automatically other correct parameters... Mode Bridge, by example... so you don't have to worry about things like that.

The WAN Port is communicating with the Ethernet switch?

I have a Comcast gateway that the router is disabled in so it acts only as a modem. This is related to an Airport Extreme, which serves as my router via the WAN on the AE port. I created a different WAP with a Capsule temporal from the airport, located downstairs with an Ethernet cable from one of the Ethernet ports on the AE to the WAN on the TC port. I think it's what we call a 'roaming network.

My question is, can I connect my switch Gigabit 8 ports in one of the Ethernet ports on the TC to complete connections wired to all devices connected on it, or should I first connect EI to the switch 8 ports and then connect the switch to the port WAN TC to complete my network "roaming"? In other words, plug it into the port WAN AE or TC still allows you to use other Ethernet ports as a switch?

Thank you!

can I plug my Gigabit 8 ports switch in one of the ports Ethernet on the TC to complete wired connections to all devices connected on it

Yes, assuming that the TC has been configured to run in Bridge Mode, which would be normal.

or should I first connect EI to the switch 8 ports and then connect the switch to the TC WAN port to complete my network "roaming"?

It would be considered preferable to wiring, if it is convenient to do so. For example, in the configuration of the wiring in the previous example just above... If there is a problem with the time Capsule, then all devices connected to the switch to the time Capsule would have a problem as well.

If the switch is connected to the AirPort Extreme, and the TC is then connected to the switch... If the TC has a problem, the other devices connected to the switch of will not be affected.

VPN ipsec active on both WAN ports?

Similar Questions

Maybe you are looking for