WAG160N assigns IP

Similar Questions

• WAG160N without internet connection

  Before I throw it I thought it might be useful to post here to see if anyone knows more than me about this problem.

  In the meantime, I have another wireless modem of va - working ATM I write/post - isn't all that urgent.

  My WAG160N router/modem I bought new 4 or 5 years, died a few weeks - over a period of an hour, or so he started to work very slowly - slowing to 10 or 20 kB / s from the usual sluggish 150ish KB/s that we normally get here.

  And then it stopped working altogether - and light stopped coming at all on the Internet.

  I pulled out and found 3 or 4 bulging capacitors in (which had burst at its lower end) that I replaced - faced with the horrible HMP weld seems to have been used to join them for the circuit.

  But still no Internet light or connection - other (wireless LAN) and DSL unit lights work, it goes through its startup sequence apparently OK and I can access all of its settings in the 192.168.1.1 page - including trying unsuccessfully to connect from one of these pages.

  It is interesting to try re-flashing the firmware - 1.00.15 currently? - or replacement of another part of the map will be working again?

  All suggestions gratefully - received I couldn't bear to throw a piece of equipment like that without having done everything I could reasonably to operate again.

  TIA

  PaulMW

  Well Saffrons7 you were right .

  And I was a bit wrong - do not understand that the settings must be correct before he was able to connect on the www.

  It was just a matter of re-assignment - and check - all the different parameters (including manual set VPI and VCI) my ISP and bingo!

  He immediately started working again!

  So, as you have said - and I got to halfway, iffen I could get to its router pages could not have been too much wrong with him - this is why I was so keen in seeing iffen I could restart. And also to get a little more networking know-how - which I am a little short on!

  The replacement of the value 2 or 3bananas caps bulging / burst seems to have been the solution.

  I use what I write this - of course - Linux I rarely use winDoze for the internet - as it is said: with winDoze you might as well put all your info on a billboard next to the road. and if you have forgotten your passwords under linux, you might as well format your hard drive.

  But the caps curved several have tended to indicate wear cheaper - which may well fool you again at some point in the future - so it's good to have 2 modems now .

  See you soon

  PaulMW

• Annex WAG160N has v2 ADSL2 + Wireless Modem Router disconnecting at random intervals

  The problem is that my WAG160N router v2 isolates at irregular intervals for no clear, obvious and clear reason. The router always reconnects to the Internet automatically, but we want to have stable internet connection so it does not interfere with our download and my game online. Sometimes, it will be disonnect once a day, two days, three days or more times a day.

  This problem occurred for about nine months and we have tried to solve this problem for four months without success and very little progress.

  There are nine devices connected to this router:

  Desktop Mac (connected by an Ethernet cable)

  MacBook Pro my mother (wireless)

  My mother of Windows (wireless) laptop

  My Iphone (wireless)

  My mom (wireless) iPhone

  Our Ipad (wireless)

  Our printer (wireless)

  My Xbox 360 (connected by an ethernet cable)

  My PS3 (connected by an ethernet cable)

  First of all, I contacted our ISP. They conducted tests on our phone line and there was no obvious abnormalities. They then made some adjustmenets to our connection, but none of the improvements to our stability of connection, either. I also did the isolation test which did not help. Then they came to the conclusion that this router is the source of the problem.

  Then I noticed that when my Internet was disconnected we had active DHCP and it kept more than one of our devices, assigning the same IP address. On my desk he showed me an IP address conflict message whenever we have disconnected from the Internet. So I disabled the DHCP and manually assigned each device to their own individual IP addresses static. This has not fixed my problem even if there are more conflicts of IP addresses.

  Then I tried to connect my computer directly to the WAG160N v2 via an ethernet cable, but each single device is always give themselves up randomly. Therefore, we have established that this problem occurs with the cable connections and wireless.

  After that, I did some research on the Internet and made a lot of adjustments and modifications that do not stop this problem.

  These including: lower the MTU to 1365, changing to channel wireless channels 1 and 6 (we were on channel 11), using a standard instead of a wide channel, lowering the keep alive - redial period from 30 seconds to 20 seconds, increasing the Redial period keep living to a maximum of 180 seconds, disable UPnP and disable the DHCP server on the router configuration page.

  I have same Access Restriction is turned off.

  I also checked with my ISP and we use the correct settings of Encapsualtion, multiplexing and Virtual Circuit.

  So I thought I would post here because we really need to have this fixed a problem and we do not know how. I can't find the logic of why this is happening. This problem shouldn't be complicated.

  Any help would be appreciated, thanks.

  My Internet has not disconnected for a week.

  Without reset and reconfigure my router, I did the following in the advanced wireless settings page:

  Reduced from 100 to 75 beacon interval

  Lowering of the threshold of Fragmentation of 2346 to 2306

  Lowering of the 2346 to 2304 RTS threshold

  I found this info from a different thread.

  I'll post again less than a week and if my Internet connection is always stable, I will mark this message as my solution.

• WAG160N & WRP400 helps wireless

  Hello

  I have a WRP400 connected to the internet and have a WAG160N, which is no longer, I use and would like to extend my wireless range.

  I have them connected via an ethernet cable and it seems to work fine without having to configure the WAG160N (seemed to just work automatically), but I can't access the admin GUI WAG160N (tried all sorts of IP addresses in the range WRP400) to modify the (frustrating). My guess is that it probably isn't the best way to implement.

  Read the posts here I follow these steps, but I have a few questions:

  1. set the IP address of the WAG160N (The WRP400 is set to 192.168.15.1, then I change the WAG160N to 192.168.15.2. Or should I be the WRP400 DHCP scope setting which starts at 192.168.15.100?)

  2 Swtich disable DHCP on the WAG160N. (I think I tried this last night and it wouldn't assign an IP address of my laptop, unless I've done somehting wrong)

  3. connect the two using an ethernet cable.

  Once I do that I should still access to the admin of the WAG160N GUI with the IP assigned to the step 1?

  Thanks a lot and I can't wait to hear your expert advice.

  Topic 1. Fix. Set the address LAN IP 192.168.15.2, outside of the DHCP pool. Be sure to leave the type of internet connection on automatic/DHCP.

  Re 2. Fix.

  Re 3. Fix.

  The port on which you connect on the WAG? Port 1 or one of the other. For Port 1, there are additional parameters in the Ethernet configuration page. You must set as port LAN 1 Port it.

  After these changes, you should be able to access the web interface on http://192.168.15.2/ but don't forget, immediately after these changes your computer uses an address of 192.168.1. *, so you can not access anything until the computer has an address of 192.168.15. *.

• DHCP with WAG160N problems

  Hello

  I just bought the WAG160N to meet my old WRT54G, but with the new router, I have problems with the DHCP protocol.

  When I turn on the computer, the router is not assigned an IP address. The problem is solved by resetting the router.

  I connect wireless computers and I tried WPA and WPA 2, but with both, I encountered problems.

  It's loaded with Firmware Version: V1.00.09 and I am trying to connect two computers works on XP and other Vista.

  Can someone please?

  problem seems to be resolved by upgrading the firmware... I'll test it for a few days and provide feedback.

• WAG160N - no internet on the wireless

  Hello, I just bought and installed a WAG160N today. I'm hard wired with my main computer and seem to have no problem at all. My lap top vista connects to the bridge, however, has no access to the internet. I changed a few settings, but without result. Any ideas?

  Wireless settings:

  Basics: Wireless config: manual; mode mixed; name: is unique; band: wide 40 mhz; wide: 9; std: 11-2, 462; SSID: enabled.

  Security: WPA2 mixed

  The rest is the default value.

  Security settings:

  Firewall is enabled

  Block anonymous Internet requests: checked.

  Now, there are two available firmware updates but I don't know who I should use

  05/06/2009
  Ver.1.00.15 - ETSI (Appendix A)
  Download 3,30 MB

  09/03/2009
  Ver.1.00.15 ETSI (Appendix B)
  Download 3.29 MB

  Your ideas are welcome. Thank you.

  Assuming that your gateway is attributed to your Vista laptop a DHCP IP address, it could be a DNS problem.  Check the settings of the gateway and DNS client. The laptop must be automatically assigned.

  To update the firmware, the majority of countries is Appendix A, for example the United Kingdom and the Australia.  Annex B would be the Germany.  In addition, the entry door you cannot use an incorrect version of the annex.

• Trying to connect a computer to the lan port Aiport Express "auto assigned IP address"

  I am trying to connect a computer to the lan on my Airport Express port. In preferences, it says "status: connected, Ethernet has an assigned IP address and won't be able to connect to the internet." Any suggestions?

  An "auto assigned" IP address indicates that your computer could not find or negotiate with a DHCP server to obtain an IP address appropriate for network access.

  It should be more on your network to provide assistance if you need it. For example, is the terminal of AirPort Express the only router in the current configuration of your network? What exact model do? What is the brand and model of your modem Internet?

• ringtone assignment

  had to get a new iphone 6 s and can not enter my iTunes ringtones to assign to contacts?   can u help?

  shandahon wrote:

  had to get a new iphone 6 s and can not enter my iTunes ringtones to assign to contacts?   can u help?

  Please provide details.

• You can assign output by ascending path to an existing project in the logic?

  Hi all

  Never really need to do until today

  Got a logic project (others 50 titles) I need to assign the output increasing outputs audio.

  Its the (only) thing that ProTools can do quite easily (cmd & option)...

  Is it possible to do in logic?

  Thanks in advance,

  Dan

  As I do this is to highlight all the tracks in the console window and then click on choose the output on the first track while holding the Option key.

• How to assign to the logic of distance in a separate in Logic Pro environment physical port entrance

  Is it possible to assign the logical KEYBOARD with a separate entrance in the port of entry of environmental Logic Pro physics?

  Thank you for your advice.

  I don't think so.  Logic of distance is considered to be a controller. Controller input data stream are made (by logic) before stopping the logic entry in physics. I "think" (I'm not an expert on remote logic) that the flow of midi is available on the port of the sum.

  I'm still not aware that you can change the channel of the South on the logic of distance. So it must be channel a (connected) and your other controllers must be able to have their midi outputs assign other channels if you demux their output.

  (please, correct me if this is not correct about the logic of distance - more conjecture on my part because I use remote logical not)

• Contacts - assign group on import

  When the Yahoo address book importing (exported as a CSV file) is it possible during import the corresponding field to assign the category (the label of Yahoo) as a group?

  The idea is to bring in a few thousand emails, who have 10 groups of different sizes.

  I know that I can a) affect the other field label or Notes and then later b) search maps for names of previous groups, c) select all and then d) create each group. I hope that I can eliminate these steps.

  You could probably do with some AppleScript, but otherwise I don't think.

  I think that the simplest solution would be to divide the file into groups and import each separately. When you import, they all appear in the last Smart import group. You can then create your new group and drag them all since the last import in the new group.

• Preview color management issue - glued assigned Adobe RGB image

  I often web elements page layout in InDesign that my composition tool, then copy and paste in Photoshop as a smart object to then generate optimized web images. It's just easier to use photoshop. Problem, it is in the latest versions of Adobe have clogged the engine of anti-aliasing and now when rasterising a PDF file or paste a picture also as a chip oppose any portion of the image of this asset is smoother. You don't really notice that if the image of origin placed in InDesign is say double or more this resolution of the web version of final product, the scale hides the issue. But if they are closer to really see faceting full size occurs. Long story... anyway, I decided to study the implementation overview of Apple as a gateway for the rasterising instead of photoshop. He did a good job on glued assets resampling, but on this point saving and checking in Photoshop, I note that Preview assigned Adobe RGB profile to the processed image. Even if I opened the InDesign PDF and export as image in my size. My color workflow is sRGB. InDesign and Photoshop are two parameters in this way, the image placed in InDesign also has sRGB profile, the PDF has sRGB profile. If I copy / paste between InDesign and Photoshop, they are both aware glued Trump space and warn me if different from that of the target document. I have no idea where Preview becomes Adobe RGB, I don't see its place in the app to change that as a preference, and in any case, it seems very strange to be a defect when most of the people would not use them.

  In the preview, click on the tools bar menu point and scroll to the bottom of the drop-down list to assign the profile

  the next submenu you can click on and select sRGB at the bottom of this list. To save this profile to your image,

  do a "save under" (click on file, press the option/alt key Save As should appear). You can also test under the view menu bar item.

  

• Is it possible to assign a different sound to my second e-mail account?

  I have two email accounts set up and works fine in Thunderbird. My main account, which I use for almost everything and a second account that I use for video surveillance and I was wondering if it was possible to assign a different sound to the second account.

  You can try this addon, it seems to be mixed results.
  Hard to know if it had fallen to not properly configure the user.
  I have not used it myself, but it must be worth a try.

  • https://addons.Mozilla.org/en-us/Thunderbird/addon/mailbox-alert/

  How to install the Extension module:
  After you download addon extension *.xpi file to the downloads or desktop folder.

  In Thunderbird
  'Tools > "Add-ons"
  or
  'The menu icon ' > 'Add-ons'

  • Click the gear icon and select 'install module file.
  • Find the downloaded *.xpi file and click 'open '.
  • You have as much need to restart Thunderbird when you are prompted.

• While the iPhone overseas requires a reactivation, which sometimes works, but more often does not work. At the beginning he said that my SIM card was not supported by the activation policy assigned by the activation server.

  iPhone 6

  Network: Verizon

  iOS 9.3.3

  Twice now, once in Costa Rica in April and, more recently, in Ireland, while that phone overseas warning reads as follows:

  "your iPhone could not be activated because the activation server is not reachable. Try to connect your phone to the iPhone to activate it, or try again in a few minutes. If the problem persists contact Apple Support to Apple.com/support. »

  or:

  "The SIM card that you have currently installed in the phone is a carrier that is not supported in the title of the activation policy that is currently assigned by the activation server. This isn't a problem with the hardware with the iPhone. Please insert another card from a supported carrier SIM or ask this iPhone be unlocked by your operator. Please contact Apple for more information. »

  My carrier is Verizon and I replaced the SIM card on my return from Costa Rica end of April despite the fact that the card is unlocked and good, in theory, for international travel,

  Before you activate the phone is locked and I can't access applications like camera, that, when I travel, I need over the phone.

  Apple says call Verizon. Verizon said, you guessed it, call Apple.

  When I return to the States, everything works fine. I thought that the replacement of a SIM card would do the trick, so you can imagine my dismay when the activation warning came after I took the phone off airplane mode after I landed in Dublin and the activation warning came new.

  What is going on?

  kennypg wrote:

  iPhone 6

  Network: Verizon

  iOS 9.3.3

  Twice now, once in Costa Rica in April and, more recently, in Ireland, while that phone overseas warning reads as follows:

  "your iPhone could not be activated because the activation server is not reachable. Try to connect your phone to the iPhone to activate it, or try again in a few minutes. If the problem persists contact Apple Support to Apple.com/support. »

  or:

  "The SIM card that you have currently installed in the phone is a carrier that is not supported in the title of the activation policy that is currently assigned by the activation server. This isn't a problem with the hardware with the iPhone. Please insert another card from a supported carrier SIM or ask this iPhone be unlocked by your operator. Please contact Apple for more information. »

  My carrier is Verizon and I replaced the SIM card on my return from Costa Rica end of April despite the fact that the card is unlocked and good, in theory, for international travel,

  Before you activate the phone is locked and I can't access applications like camera, that, when I travel, I need over the phone.

  Apple says call Verizon. Verizon said, you guessed it, call Apple.

  When I return to the States, everything works fine. I thought that the replacement of a SIM card would do the trick, so you can imagine my dismay when the activation warning came after I took the phone off airplane mode after I landed in Dublin and the activation warning came new.

  What is going on?

  I think it's a problem with Verizon.

  Our company is on AT & T - and our lawyer have travel all over the world, Africa, London, South East Asia and they have never complained to me than before.

• How can I get an identity to be assigned automatically to a message?

  Is it possible to get an identity specific to assign as a principal to a (outgoing) message automatically, dependant on the record where I am from enamel?

  I realize it's me, but I always forget to change identity in the drop-down list area.

  Thank you very much.

  John.

  What you describe, that's what's supposed to happen automatically. (Well, it is supposed to use the identity of the account that you are currently in.)

  There are a lot of Add-ons for this problem to a search for identity in the modules search tool.

  Some that I have used or tried:
  Correct Identity: https://addons.mozilla.org/en-us/thunderbird/addon/correct-identity/
  Accounts of file: https://addons.mozilla.org/en-US/thunderbird/addon/folder-account/?src=api might be close to what you are looking for