Want to 750-055xt: POWER PN 746177-001 SPECIFICATIONS AND REPLACEMENTS

Similar Questions

• HP PC laptop power cord safety program removal and replacement

  I buy laptop HP P r022tx last month. I saw that HP Notebook PC AC Power cord safety recall and the program of replacement on the HP site. According to the guidelines that I check my adapter, it is of type LS-15. But so far I can't find such a problem of large heating in it. Should I ask replacement if she will give such a problem in the future...

  Please follow the link:

  http://h30434.www3.HP.com/T5/notebook-hardware/HP-laptop-power-cord-safety-recall-and-replacement/m-p/4393930/highlight/true#M144809

• Want to 750-055XT: new computer does not start

  The computer starts nine on eon can't. Customer support attempts were in vain. Yesterday evening was told to perform a test on the drive hard and at the request of a call, but never followed. Computer started this morning, but after a stop (stop through Windows), attempts to restart failed. 40 minute wait estimated with the horrible horrible music and recorded wife makes me crazy. Should I return it and get my back money and shop elsewhere? It was a horrible experience.

  Greetings,

  No point troubleshooting your PC isn't new.

  Return for a refund as soon as POSSIBLE!

  See you soon!

• Want to 750 - xt 550 (CTO): Desktop problems Bang and Olufsen Sound of 750 - xt HP Envy with the brand-new office

  I bought a new system and it arrived yesterday, in the introduction, I have a 5.1 speakers Creative Labs system (which worked perfectly in my previous HP media center PC) I'm connected (using the catch green, black and Orange on the back of the system).  Using the Bang and Olufsen 'test' feature, I hear from "front speakers' (green connector), the Center and the subwoofer (Orange wire) no sound from the surround speakers (black wire).  The sound is HORRIBLE, roaring, low volume, just horrible.

  If I pass the black cable (surround) at the entrance to white (side speakers) I can hear the sound on the 5 speakers, it's always horrible and very, very disappointing!  I spent over 4 hours on the phone last night with HP Support who told me, in conclusion, that my system does not support sound 5.1, I will be able to use Stero (i.e., the Green connector).  My number is 3023344605, the discussion was just a mess.

  Can somone suggest please how can I get my sound working properly?

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.
  If you are unfamiliar with works as a private of the Forum messages, this post has instructions.

• HP 750 055xt: clean install / desire / network driver problem

  Want to 750-055xt. Bought as a refurb. SSD is small, so I put more in and did a clean install with Windows 7 Professional.

  Internet - network driver problem does not connect and I see that the drivers are missing. I tried searching the site, but I can't find the driver.

  It's not a hardware issue because I can put the other drive and it works fine.

  I am struck an impasse with the search tool. I need to copy the driver on another computer to move.

  All of the suggestions.

  Thank you.

  Hello:

  Page for your model motherboard plug indicates that there is a CG-RTL8151GH-Realtek gigabit ethernet card.

  See if the W7 directly from Realtek driver works - 3rd driver on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• Want to 750-114: migrate another computer with SSD

  Hi all

  Im trying to replace my old PC with this desire 750-114.  I have an SSD on my old PC and would like to just transfer the SSD to my envy again as the main drive.

  I couldn't find any driver motherboard online and I don't want to clone the hard disk on my new PC I want to keep all the files on my old intact SSD.

  is it possible to boot from my old SSD?

  Thank you!

  weidake

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your message want to migrate a SSD from one PC to another and wanted to help.

  Simply boot the second PC since a SSD at the first - No..  IF the PC had identical hardware, then maybe, but with a different material, the necessary drivers will be missing and the PC does not start.

  There is a way to actuall "migrate" from the old PC to the new one, using the same player - but it involves costs and considerable work.

  Macrium Reflect allows image and restore the PC and they have an option that you can do whatever you want - mainly migrate everything from your old PC to the new - it's called the redeployment, and it is not available in the free version.  You must buy the Home version.

  The way it works in your case is that you buy Mr., install on a PC and use the option to create the bootable rescue media.

  Then you put the old SSD in the new PC, insert the bootable rescue media and boot into MR.

  Once it is running (it may take a few minutes to load), follow the instructions in this thread (from step 3): http://www.macrium.com/help/v5/How_to/Redeploy/ReDeploy_a_system_to_new_hardware.htm

  Mr. then read drivers (from support that you provide) and replace the drivers on the SSD with the drivers for the new PC.

  NOTE: If you do not have the drivers for your new PC in one place, and then download and install DriverBackup - you can use this to backup all the drivers in a single folder.

  But it's only PART of the solution (I said that some work is involved!)

  The former DSS had active Windows using the license on the old PC - and OEM licenses are not transferable from one PC to another.

  If the new PC is preinstalled with Win8x or newer, you can retrieve the info from following these instructions (based on 90 days version) license:

  (1) for Windows 8 x: key product - find for Windows 8

  (2) for Windows 10: download the OEM of Windows - MajorGeeks product key tool

  You will then need to manually enter the product key found by the tool to activate Windows again on the new PC.
  
  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• 750 - 055xt CTO M0K53AV #ABA envy: HP has encountered an error when trying to analyze your product

  I use a brand new HP Envy 750-055xt CTO. Added the SSD (Samsung 850 EVO 120 G) and 16G Ram (Total of 24G (from Crucial)). The Win 7 OS has migrated to SSD and formatted the original drive for the purpose of storing files to a printer large format (new HP Latex, which will happen later this month).

  Attempted to install Windows 10 but had multiple failures with error 0x80073B92 - 0 x 20009.

  Disconnected SSD in case it was originally the above error, restored the system using created recovery DVD to state of origin (but always with 24 G of Ram).

  In trying to pilot research and updates to bios on the HP support page, I now encounter error "HP has encountered an error when trying to analyze your product" which leaves me to proceed, except to order the DVD of restoration Windows 7.

  I know I'm forgetting something in this whole procedure, but I have no idea at the moment what it could be.

  This can help with the installation:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-windows_install/Windows-10-upgrade-failed-with-0x80073b92-0x20009/15eaaeab-9ECB-4C06-bd8d-62c783d51cf6?auth=1

  HP site:

  http://h30434.www3.HP.com/T5/notebook-operating-system-and-recovery/error-while-trying-to-scan-product/TD-p/5369812

  Hope this helps

• ENVY 750 - 055xt: screw the motherboard for socket mSATA

  I have the HP ENVY 750-055xt, which uses the motherboard of Kaili.  There is a plug on the motherboard mSATA and I inserted an EVO of 850 Samsung 1 TB SSD.  Fortunately this solid state drive works and is immediately recognized by Windows 7, no other frills.  However, the motherboard doesn't have the small screws in the tiny mSATA solid drive on the motherboard.

  Anyone know the right screw size used to secure the mSATA SSD to the motherboard in Kaili?

  Hi Big_Dave,

  Thanks for your reply.  I have besides a picture of the Samsung 850 EVO mSATA SSD drive.

  

  It fits in the slot on my motherboard HP MS-7826 (Kaili) mSATA.  Please see below.

  

  The drive performs as well as my boot drive.  As it is not properly attached to the motherboard, the only thing holding is the strength of tensioning of the socket.  Ocassion the tiny jury comes off in the socket and it won't be visible in the path of startup.  Opening upward the chasis LIKE 750 and re - insert the mSATA jury will get the computer running again.  The little screw would prevent the Council of Regularisez making and the frustration of re-Foundation there.

  Elsewhere in this forum, I found mention of the screw that I'm looking.  This is the same as that used in the dwelling of minimap express PCI used for the WiFi card.  The expertise here source describes the machine screws Flathead as a M1.6 size.  I ordered a M1.6 x 3 mm of China.  I think it should work.  Some here said they used a M2.0 to head flat screws in the slot mSATA and it seemed to work for them.

  My motherboard HP isn't a slot m2.  If so, then I probably would have opted for the Samsung SSD m2, instead of the mSATA SSD drive.

  For now, I think I solved the problem with the mother screw missing for the location of nSATA.  Nevertheless, Big_Dave, thanks for responding to me here.

• WANT to 750-055 CTO: 750-055 CTO Intel RST ENVY

  I was make a copy of my DESIRE 750-055 CTO of a 750 refurb.  I made it all up and running. With the help of you guys on the forum.  All that is left is that I am putting together does not have the Intel RST # 14.8.7.1051.  What is in my original computer.  Being a dummy I copied my original computer and put it in place in the programs.  But of course it does not appear in the search, and the configuration file is missing.

  What can I do to get the entire file.  I tried the site and apparently after 4 pm, EST it stops.

  Thanks for all the ideas.

  Hello

  It doesn't seem to be all pilots stationed the CTO of 750-055xt feel LIKE at the moment.

  However, try this link HP.

  I ask HP to focus on the issue of missing drivers.

• I want to buy a Apple Watch in the Canada and use it and load it in Ireland. Is this possible?

  I want to buy a Apple Watch in the Canada and use it and load it in Ireland. Is this possible?

  Hello

  If you buy a Apple Watch the Canada, it will be completely compatible with your iPhone in Ireland.

  There are no regional differences in the hardware specifications for the watch, which can be configured to use your preferred language and format of the region.

  The included USB adapter pins will be located at the Canada. However, for charging your watch via the food in Ireland, you can use the charge cable provided on the magnetic head with a real 5W Apple (iPhone) or 12W (iPad) USB power adapter. You can also buy an extra Apple USB power adapter for your watch the Apple Store online for the Ireland:

  http://www.Apple.com/IE/shop/product/MD812B/C/Apple-USB-power-adapter?FNODE=83

  Service of the material to the title of the one year limited warranty is also always available in Ireland.

• Legacy with defective power supply unit. Looking for replacement source

  RND4000 (ReadyNAS NV + v1 [v3]) group legacy with a power failure. Looking for replacement source. Not after replacement free of charge since it is obviously out of warranty and end of product life. However, it is a little expensive Kit to replace. If I did, I would still want to use it as a backup of synchronization for the new.

  I was unable to find any power supply corresponding by the name given to the unit (ST-220FUB-05F), all the results of my research resulted in a power different with smilar looks and namesake. Main differences are slight changes in the output rails, different output connectors. Also include a fan that mine didn't, perhaps a clue to the failure there.

  I was shocked to find that he was / is none replaceable fuse in the power supply and if there was a gauge commonent that he was unable to do the job because a cracket big mosfet to clean his radiator, think that's what it is, hard to see in here. Unable to find a replacement, I'll have to try to replace the component that is visibly damaged. Not easy because it's crowded in there and may fail because there are perhaps other failing components that didn't explode or evacuate. I really need ot get this unit backup and running.

  Help, please. Consider the purchase of an equivalent of second hand RND4000 for parts. See you soon.

  Hello EkDor,

  This replacement of power supply was free until supplies last and I heard they already ran out of it.

• the power of the spectrum graph and butterworth filter

  Hello

  I am beginner in labview, I want to see the power spectrum of the sound samples, I want to see if there is any reason in these samples.

  I use spectral measure, and then I filtered with butterworth filter samples. For output I using waveform graphs.

  Before filtering the signal, I'm in the x axis of the graph between 0-22500 and the data mostly in 0-2500.

  I've tried to filter using these values (fs = 1000 Hz, 0.125 hz = fl and fh = 500 hz) and the graphics almost the same thing but the axis of the graph is between 0-0, 5.

  issues related to the:

  What is the x axis properties? Why is different, but the graphics are the same?

  Make the mistake with the program?

  Hi Limavolt,

  You have a problem with the bandpass filter VI, this VI generates only the signal of value i.e. table DBL. The signal is a cluster.

  solution 1: you need to calculate 'dt' using the sampling frequency and use VI waveform construction to generate a signal's own scaling. 

  Normally, dt = sampling frequency/No. samples

  Solution 2: replace the VI butterworth filter with filter VI express, this will produce signal without scaling.

  

• I have UN-plugged my speakers and replaced by headphones. Noise if the headphoens is fine. I now want to put the spekares back in, but there is no sound at all

  original title: SOUND

  I have UN-plugged my speakers and replaced by headphones. Noise if the headphoens is fine. I now want to put the spekares back in, but there is no sound at all. Can anyone help?

  So they are pregnant Dell with standard 3.5 mm USB powered plug (* and even the green port plug in as shown in the picture)?

  Therefore, the USB plugged into the port in the back of the computer for power to the speakers?  Try a different USB port - just to see if the chosen one does not provide the necessary power.

  Make sure that the speakers are turned on and the volume is turned all the top (to the right).

  Make sure that the sound output is not cut on your computer (plug in the headphones to check what you mean by them.

  Plug the 3.5 mm of the speaker to the green port on the computer (see photo above.)

  If you don't hear sound... Unplug the plug 3.5 mm and touch something metal - static electricity?  The speakers become power at all?

• My iphone 6 does not light, I held the home button and power at the same time and no vibration or no sign of life, any suggestions as to what it could be would be appreciated

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Marley6921 wrote:

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Put it on wait ten minutes if the phone did not come one, then hold down the sleep/Home button until you see the apple logo and then release, make sure that the phone is still connected to the charger.

• I want to change the name that appears under 'To' and the 'author '.

  I want to change the name that appears under 'To' and the 'author '.

  No matter what particular place, or simply everywhere where you happen to be at this time?