Why my print spooler turn?

Similar Questions

• Print spooler does not work

  Cannot print and all of my printer disappeared from my print list. Print spooler not working do not mistake

  Cannot print and all of my printer disappeared from my print list. Print spooler not working do not mistake

  You can start the print spooler by clicking Start > run and type the following command in the box run and then click OK:

  net start spooler

  The real question, however, is why the print spooler service is stopped and you should do to prevent it to stop again.

  You have a recent antivirus application with an active subscription? Which one?

  Have you scanned your system for malware using MalwareBytes Anti-Malware AND SUPERAntiSpyware ?  If this isn't the case, get these free scanners and do.  Do not forget to update before you scan them.

  If you have never installed a Lexmark printer, follow the instructions in a single Article to remove and reinstall the drivers for your printer.

  If you have or had a Lexmark printer, follow these directions as well (from http://members.shaw.ca/bsanders/CleanPrinterDrivers.htm )

  If you have a Lexmark printer , these additional steps may be necessary (thanks to Robert Orleth [MSFT] to provide this information).  Sometimes, the Lexmarkprinter installation process installs a service that makes dependentPrint Spooler service itself.  If there is a problem withservice Lexmark or a Lexmark printer driver (or you have removed using the procedure above),Print Spooler service does not start (see also http://support.microsoft.com/default.aspx?scid=kb;en-us;324757 ).  The steps below makePrint Spooler service only on service (RPCSS) remote procedure (RPC) call, which is normal.  Print Spooler service dependencies are stored in the registry at

  HKEY_LOCAL_MACINE\SYSTEM\CurrentControlSet\Services\Spooler\DependOnService

  ... The sc config command resets the value for this entry.

  1. Open a command prompt window

  2. the control key
            sc config spooler depend = RPCSS
        (Note the space after the = not before)

  3. Restart print spooler (see steps 8 and 9 above)

• Print spooler errors

  I tried for over an hour to get my printer to work spooler & it still gives me the error message "spooler subsystem app stopped working."  I tried to change the properties of printer spooler, turning on & off windows features, microsoft 'fix - it', etc.  Any other suggestions?  Sometimes, he has printed a test page, and then returns to the error when the next attempt to print.  I've never had this problem until I tried to print an attachment to my e-mail tonight.

  Hi Angie_08,

  Please see the thread with a similar problem and fix possible:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/Spooler-subsystem-app-has-stopped-working/dc28487d-f6af-4D4E-a7c9-22410b5603cf

  I hope this helps!

• Printer Spooler not working!

  Does anyone know why the print spooler does not work, what are the causes and how it can be fixed? Because of this problem, I am unable to install a printer on my computer. I spent endless hours on the phone with tech support trying to install a printer, but without success... Then we had the errorr message saying that the printer spooler does not work.

  Thank you!

  http://support.Microsoft.com/kb/2000007/en-us

  Solve printing problems by resetting the print spooler

  I hope that the information above solves printing problems you encounter.

  See you soon.

  Mick Murphy - Microsoft partner

• I can't print. It says local print spooler does not work, restart the printer or machine.

  I use windows7, I can't print. It says local print spooler does not work, restart the printer or machine. I can not install, or add the printer currently installed in my computer. Help, please.

  Original title: printer

  Hello

  The print spooler is the mechanism that will interface between your application and the printer and coils (sends) the print job to the printer. It should start automatically when you start your machine. So, restart your computer and try again. I suspect that the real problem is to find why the print spooler has stopped in the first place.

  After trying again, see what happens and if your print spooler stops again, the real work will begin.

  Kind regards

  BearPup

• Printer Spooler service turns off - Windows 7

  Hi guys.

  After trying and trying several solutions online to resolve Printer Spooler service, still me have the same problem.
  The spooler goes off in a split second, as soon as I turn it on.

  Ive tried to delete all printers.
  Also there isn't any "Printers" folder in the following directory: c:\Windows\System32\spool

  I got the report of accident for you to source: C:\ProgramData\Microsoft\Windows\WER\ReportArchive

  Please indicate how I can solve the problem of spooler and let it run?

  'Version = 1 '.
  EventType = APPCRASH
  EventTime = 130201389863919618
  ReportType = 2
  Consent = 1
  UploadTime = 130201389889851101
  ReportIdentifier = a5bf9ca2-fd6c-11e2-910f-88532e4161ca
  IntegratorReportIdentifier = a5bf9ca1-fd6c-11e2-910f-88532e4161ca
  Response.BucketId = 62923011
  Response.BucketTable = 4
  Response.Type = 4
  SIG [0]. Name = name of the Application
  SIG [0]. Value = spoolsv.exe
  GIS [1]. Name = Version of the Application
  GIS [1]. Value = 6.1.7601.17777
  GIS [2]. Name = timestamp of the Application
  GIS [2]. Value = 4f35fc1d
  GIS [3]. Name = name of the Module fault
  GIS [3]. Value = HpTcpMon.dll
  GIS [4]. Name = Fault Module Version
  GIS [4]. Value = 7.2.5.51
  GIS [5]. Name = Fault Module Timestamp
  GIS [5]. Value = 4ab0e4d3
  GIS [6]. Name = Exception Code
  GIS [6]. Value = c0000005
  GIS [7]. Name = offset of the Exception
  GIS [7]. Value = 000000000000ad75
  DynamicSig [1]. Name = OS Version
  DynamicSig [1]. Value=6.1.7601.2.1.0.768.3
  DynamicSig [2]. Name = locale ID
  DynamicSig [2]. Value = 1033
  DynamicSig [22]. Name = additional Information 1
  DynamicSig [22]. Value = df36
  DynamicSig [23]. Name = additional Information 2
  DynamicSig [23]. Value = df36e0b278c770807cefd993fac9d654
  DynamicSig [24]. Name = additional Information 3
  DynamicSig [24]. Value = a612
  DynamicSig [25]. Name = additional Information 4
  DynamicSig [25]. Value = a612b538cec9db3725c9e02da3121443
  UI[2]=C:\windows\System32\spoolsv.exe
  UI [3] = Spooler SubSystem App stopped working
  UI [4] = Windows can check online for a solution to the problem.
  UI [5] = check online for a solution (recommended)
  UI [6] = check for a solution later (recommended)
  UI [7] = close
  UI [8] = Spooler SubSystem App stopped working and was closed
  UI [9] = a problem caused the application to stop working correctly. Windows will notify you if a solution is available.
  UI [10] = & close
  LoadedModule[0]=C:\windows\System32\spoolsv.exe
  LoadedModule[1]=C:\windows\SYSTEM32\ntdll.dll
  LoadedModule[2]=C:\windows\system32\kernel32.dll
  LoadedModule[3]=C:\windows\system32\KERNELBASE.dll
  LoadedModule[4]=C:\windows\system32\msvcrt.dll
  LoadedModule[5]=C:\windows\SYSTEM32\sechost.dll
  LoadedModule[6]=C:\windows\system32\RPCRT4.dll
  LoadedModule[7]=C:\windows\system32\USER32.dll
  LoadedModule[8]=C:\windows\system32\GDI32.dll
  LoadedModule[9]=C:\windows\system32\LPK.dll
  LoadedModule[10]=C:\windows\system32\USP10.dll
  LoadedModule[11]=C:\windows\System32\POWRPROF.dll
  LoadedModule[12]=C:\windows\system32\SETUPAPI.dll
  LoadedModule[13]=C:\windows\system32\CFGMGR32.dll
  LoadedModule[14]=C:\windows\system32\ADVAPI32.dll
  LoadedModule[15]=C:\windows\system32\OLEAUT32.dll
  LoadedModule[16]=C:\windows\system32\ole32.dll
  LoadedModule[17]=C:\windows\system32\DEVOBJ.dll
  LoadedModule[18]=C:\windows\System32\DNSAPI.dll
  LoadedModule[19]=C:\windows\system32\WS2_32.dll
  LoadedModule[20]=C:\windows\system32\NSI.dll
  LoadedModule [21] = C:\windows\system32\IMM32. DLL
  LoadedModule[22]=C:\windows\system32\MSCTF.dll
  LoadedModule[23]=C:\windows\system32\nvinitx.dll
  LoadedModule[24]=C:\windows\System32\CRYPTBASE.dll
  LoadedModule[25]=C:\windows\System32\slc.dll
  LoadedModule[26]=C:\windows\System32\RpcRtRemote.dll
  LoadedModule[27]=C:\windows\System32\secur32.dll
  LoadedModule [28] = C:\windows\System32\SSPICLI. DLL
  LoadedModule[29]=C:\windows\System32\credssp.dll
  LoadedModule [30] = C:\windows\System32\IPHLPAPI. DLL
  LoadedModule [31] = C:\windows\System32\WINNSI. DLL
  LoadedModule[32]=C:\windows\system32\mswsock.dll
  LoadedModule[33]=C:\windows\System32\wshtcpip.dll
  LoadedModule[34]=C:\windows\System32\wship6.dll
  LoadedModule [35] = c: Files\Microsoft Shared WLIDNSP. DLL
  LoadedModule [36] = C:\windows\system32\PSAPI. DLL
  LoadedModule[37]=C:\windows\system32\SHLWAPI.dll
  LoadedModule [38] = C:\Program Files\Bonjour\mdnsNSP.dll
  LoadedModule[39]=C:\windows\System32\rasadhlp.dll
  LoadedModule[40]=C:\windows\System32\fwpuclnt.dll
  LoadedModule[41]=C:\windows\system32\CLBCatQ.DLL
  LoadedModule[42]=C:\Windows\system32\umb.dll
  LoadedModule [43] = to C:\Windows\system32\ATL. DLL
  LoadedModule[44]=C:\windows\system32\WINTRUST.dll
  LoadedModule[45]=C:\windows\system32\CRYPT32.dll
  LoadedModule[46]=C:\windows\system32\MSASN1.dll
  LoadedModule[47]=C:\windows\System32\localspl.dll
  LoadedModule [48] = C:\windows\System32\SPOOLSS. DLL
  LoadedModule[49]=C:\windows\System32\srvcli.dll
  LoadedModule[50]=C:\windows\system32\winspool.drv
  LoadedModule[51]=C:\windows\System32\PrintIsolationProxy.dll
  LoadedModule[52]=C:\windows\System32\HpTcpMon.dll
  LoadedModule[53]=C:\windows\System32\HPTcpMUI.dll
  LoadedModule[54]=C:\windows\WinSxS\amd64_microsoft.windows.common-controls_6595b64144ccf1df_5.82.7601.17514_none_a4d6a923711520a9\COMCTL32.dll
  LoadedModule[55]=C:\windows\System32\hpzjrd01.dll
  LoadedModule[56]=C:\windows\System32\hptcpmib.dll
  LoadedModule[57]=C:\windows\System32\mgmtapi.dll
  LoadedModule[58]=C:\windows\System32\snmpapi.dll
  LoadedModule[59]=C:\windows\System32\wsnmp32.dll
  State [0]. Key = transport. DoneStage1
  State [0]. Value = 1
  FriendlyEventName = Stopped Working
  ConsentKey = APPCRASH
  AppName = Spooler SubSystem App
  AppPath=C:\windows\System32\spoolsv.exe ".

  Hi Marius,.

  As you mentioned that you are unable to find the folder of spool, check if spoolsv.exe is present under C:\Windows\System32.

  Follow these tips and check if that helps.

  Method 1: Run the built-in printer Troubleshooter and check if that helps.
  Open utility troubleshooting printer

  Method 2: I suggest you refer to the suggestion of Gokul T responded on November 6, 2009, for a similar problem.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Windows-7-print-spooler-will-not-start/79938f9a-34b2-4ddf-8101-e20f7fa9c2d0

  You can also consult about it and see the advice given by Freak05, Tuesday, July 27, 2010.

  Print spooler keeps stopping on Windows 7

  http://social.technet.Microsoft.com/forums/Windows/en-us/fd7f46d3-Baa1-4a38-9AD3-dec5426d9297/print-spooler-keeps-stopping-on-Windows-7

  Reference: why I can not print

  Follow the suggestions in the thread and let us know the results.

• Why is my computer is giving me an error message that says: "cannot start service on Local computer print spooler?

  Why is my computer is giving me an error message that says: "cannot start service on Local computer print spooler?

  When I tried to install my printer, I got an error 1068: the dependency service or group could start. I tried to go into my computer management to enable the print spooler service, but it gave me the same error message each time. What is the dependency service or group and how I put in place?

  Hi SimoneJ,

  Try to replace spoolsv.exe is located in C:\windows\system32 in C:\WINDOWS\ServicePackFiles\i386.

  Starting from printer spooler services (start-> Run-> services.msc-> printer spooler).

  I hope this helps.

• just installed my printer today. was working fine and then got a message error that says "print spooler is not activated" or something like that. How do I turn it on? I tried to understand for 30 minutes... Help, please!

  help to turn on print spooler

  Hello Bubbalooloo,

  Thank you for your message.  To enable the print spooler, please follow the steps below:
  Click 'Start' > right click on 'My computer' > select 'manage '.
  Click the (+) sign next to "Services and Applications" > click on "Services".
  On the right, scroll down to and double click on 'Print spooler' > set the startup type to "Automatic" > click on 'Start' > click 'Apply' > click 'OK '.
  This should not only start your spooler in this instance, but now he has to start each time you start your computer.
  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Print spooler not turned on do not, how do I turn it on?

  I did a search print spooler, but when I try to open it with windows search, nothing happens.  Troubleshooting repeatedly tells me that my printer does not work because it is turned off.  I tried to uninstall, but impossible to reinstall without the print spooler on.

  Type services in the start search box, press on enter.

  Go to the bottom of the list of print spooler and click on start.

• Print spooler is disabled, how to turn on?

  Original title - print spooler

  I received a message stating that my print spooler is disabled after that I had to reformat my new machine, Windows 8. How do I turn this thing? Sorry to be a Luddite.

  Steve,

  What printer you are using? What is the model?

  Which printer driver you installed on the computer? He received by the manufacturer of the printer?

  Try this:

  Open Services by typing "Services.msc" in the Run command window and clickin on 'Ok '.

  Double click on "Printer Spooler" Services listed there.

  Click on stop, click OK and go to '% WINDIR%\system32\spool\printers' and all delete this folder.

  Now again go to Services.msc and start the Printer Spooler service and change the startup as "Automatic" Type

  Click Ok and restart the computer and check.

• Printer error print spooler service does not? Why not

  I have a problem with my printer .  I went to use this boy was that cannot use a misstake... go Control Panel /printer .and see I have no printer and you can't print at all.  I tried to instwith a CDerror the Print Spooler service does not... I need help big time what should I do? 

  HELP Florida Irving

  Hello

  Try the steps below and check if they help to resolve the issue.

  Method 1:

  Check the link below and try the troubleshooting steps provided to solve the problems with the printer in Windows.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 2:

  If the steps in the link above do not help, try to manually restart the Printer Spooler service.

  You must be logged on as administrator to perform these steps.

  (a) open administrative tools by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Administrative Tools.

  (b) double click Services.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  (c) right click on the print spooler service, and then click Properties.

  (d) on the general tab, next to startup type, make sure that automatic is selected.

  (e) if the service is not already running, under Service status, click Start and then click OK.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation

• When he tells me that the print spooler is turned off, where I'm going to turn it on?

  my printer works, now every time I try to print anything it tellsme the local print spooler service does not work, restart the spooler or restart the machine.

  How can I restart the spooler?

  Hello

  ·        You did changes to the computer before the show?

  ·        You receive an error with the error code?

  ·        What is the number and model of the printer that you are using?

  Method 1: I suggest you run the fixit from the link and if it helps:

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/en-us?EntryPoint=lightbox

  Method 2: You can also try the steps from the link:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
  Reference: Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

• Vista and Color Laserjet 5 M reprints all when the printer is turned on?

  Vist and Color Laserjet 5 M reprints all when the printer is turned on?

  It is a new one on me. I installed the printer with a barrette SIMM Postscript so it would work even at all under Vista and now it prints well but insists on the fact that I have all re - print he has never seen a reason any whenever I turn the printer to print something again.

  XP he has never done that, but I've always had the document cannot print the error that I ignored as he did print correctly.

  Google has not really revealed anything?

  ?? Type response level 1 I was looking for... These printers are a full restart, test of memory and when it is off.

  But I think I solved it, spent some time on google and there was a suggestion on the spooler in vista, was something like clear keep printed documents or print spooling first, I went also to start printing after the last page. Who took care of a lot of it somehow. Not sure why the generic installation program would need to be changed here. Possible I did for me somehow when I was trying to get the thing to work with the PCL driver too.

  Then I noticed that whenever I turned on the printer it is printing a page of demo postscript, for some reason any, it is enabled by default in the SIMM option. Turn power off and now its not wasting so much paper now.

  So two things to look for in the computer and the printer.

• My printer is turned on but not paper will just slip

  Original title: printer printingmy printer is turned on but not paper will just slip

  printer is on, but does not print

  Hello

  This problem can be caused if the print spooler service is not started or it might not be enough ink in the ink cartridge.

  I would really appreciate if you could answer the following questions:

  1. what operating system is installed on your computer?

  Operating system Windows am I running?

  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  2. What is the brand and model of the printer?

  3. you receive an error code or message?

  4. have you made any recent hardware or exchange of software on your computer before the show?

  5. have you checked for enough ink ink cartridge print?

  Follow the step by step tutorial to help you identify and fix common problems of printer from the link.

   

  Why can I not print? :

  http://Windows.Microsoft.com/en-in/Windows7/why-cant-i-print

   

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• Printer spooler does not work for a single user on the network printer

  original title: very different printer problem

  I have a HP deskjet printer shared from a PC on the network.
  I was informed of a single person could not access error poped by saying "printer spooler does not work.
  I went to the services and made sure it was infact running and rebooted to be sure also restarted the RPC services as it is addictive
  Still, the user cannot print to the printer. I took the computer that has been seen issues and hung where fixed my PC and I am able to connect and print!

  If I move my computer witch would allow me to print before there where his computer is my computer prompt same error

  My idea is - what some are how a network issue, but the user can still access drives network, internet and other printers on the network

  Just not this printer

  The computer on the share is is a windows xp sp2 workstation

  The computer with the issue is any system I plug its cable Ethernet (XP anyway) I have not tried with a windows machine 7.

  My hypothesis is a bad Ethernet cable? I'm quite lost with this question at this stage.

  My next step is to hang the printer until a print area and assign an IP address and finish with the share.

  (Still not sure if it would help or not)

  Any advice is welcome thanks

  It turned out to be a bad switch. I don't understand why it did not work. All the computers had no problems other than the present even that if I swapped the ports it has made a difference.

  Hung new switch and all computers works fine now.