Win XP in a strange state

Similar Questions

• Strange state of eclipse

  Somehow, I lost a lot of features in Eclipse associated with Blackberry. First, you'll notice in the screenshot below that there is a framework for 'Blackberry' below 'Run as' and 'Debug '. This would normally be where I could "launch the device.  In addition, you will notice that the blackberry icons are not near the top of the screen. "For things like ' Debug as", 'Own Simulator' and 'Run as' icons are all absent.

  I put the perspective to 'Blackberry '. I am at a loss why this feature is missing. The only things I could see a conflict at this time was the I've installed the plugin "egit" recently.

  Any suggestions would be greatly appreciated.

  Thank you!

  

  I still don't have the "Blackberry" text in the pop-up menu under "Debug as". The good news is that I am just using the top Menu under "Blackberry" and I have all the options available out there. Strange things goes away but at least I have a workaround solution.

  Thank you for your kind reply

• PE T610 - Perc 6i - strange state after adding additional drives

  Hello

  We have a PE T610 with a PERC 6i controller.

  X SATA 1: 2 250 GB virtual disk in a RAID-1

  X SATA 2: 3 500 GB of disk virtual in a RAID-5

  We have added 3 additional 2 TB drives to the server.  A drive has been designated as a Global Hot Spare.  Two other readers have been added to the Bay RAID-5.

  I predicted, using 500 GB each among the readers added two for Virtual Disk 2.  Then, I had planned to use the other 1.5 to among the readers as Virtual Disk 3 in a RAID-1 array.  I did it with other servers in PE in the past.

  But after that the 500 GB is used from each of the discs, I can't used the remaining unused space.  It shows the 'available RAID disk space' as 0.00 GB.

  Why the remaining space on these disks is not available for me to use?

  Thanks for any help on this.

  Bryan Hunt

  «I've waited with 500 GB each among the readers added two for Virtual Disk 2.»  Then, I had planned to use the other 1.5 to among the readers as Virtual Disk 3 in a RAID-1 array.  I did it with other servers in PE in the past. »

  This was allowed on a VERY small number of controllers found in Dell servers.  Anyway, you can do that on 6 PERC.  You can replace your existing 3 drives with 2 TB drives, then create a second table (6 to) on the disks (all disks in a disk group must have the amount of space available and impossible to replace the drives with the greatest and to increase the existing RAID array size).

• 600xt only occasionally don't market/wake... light green on the AC adapter is released... strange

  In the last 3 weeks or so our TouchSmart 600xt goes into a strange state 4 different times... have been left unattended for a period of time that we return to find the machine seems to be off and does not turn on via the power button (the button on the top right of the screen). He's usually asleep after 20 minutes, and if the Start button / stop he sleep will be orange glowing... in this case the light turns off completely. In addition, in this case the green light on the power adapter is not lit. The behavior of power adapter is quite out of the ordinary; its light never seens is disabled, even if the PC is turned off completely. But it is when this happens.

  The only recourse seems to be to unplug the power adapter, and then plug it back, after which the green light on the adapter lights, the power button lights up and the machine can be turned on by the power button.

  Concerned we will lose some files if stops keep occurred. We had the machine almost a year and this is a new behavior in the last 3 weeks. Note, however, that during each sleep cycle didn't appear. (The machine goes to sleep after being unsupervised on average 6 times a day and it produces "only" 4 times he slept in the last 3 weeks).

  Thoughts? Some circuit for energy in the power adapter went wrong maybe?

  I have come to resolution on this, but in a quite ridiculous way, with HP. My machine is under warranty so I called HP support. They have paid shipping for me to return the PC. The shipping box included explicit instructions, not to include the power adapter. I've included anyway so they could use it in the trials, including a note on the behavior and I figured the adapter not the PC. They I returned the PC with a note saying they were unable to repro the problem, and highlighted with a copy of the notice with the part that I intentionally did not follow! The log files indicate this was true, but he had not yet left on the MTBF I mentioned in the note... So even if they had used the adapter in the test, which is not surprising. The problem reappeared in the days at home. I called again. They paid shipping again. I've included the adapter again. This time they kept the PC on in the laboratory for several days until something of villain that has happened with the graphics drivers... not the unexpected loss of power and not something that I've never seen before in the newspapers. They replaced this material returned set. The problem reappeared in the days at home. I called one more time and said ' Please, can you just send me an AC adapter... If that doesn't work I'll send it back.» They did it. And I started using it. The problem is not reappeared since.

• New Office WIN 7 with SSD & data disks - how to configure programs off the C drive & users

  All new computer win 7 pro 64-bit & State of the art everything.  SSD 128 GB & 2 - 2T in RAID 1 data drives.

  SSD 128 C:\ & WIN 7 becomes all the settings are there.  "I want to move - or add - all future users & programs on the"data disk"F" as the default for the operating system.

  This is the version abridged - ask & I'll tell you anything.

  I should post this in another forum?

  May I ask then, what was the point of investing in an SSD? The point of having an SSD is that Windows 7 starts and works faster to your programs will load faster. You must store 'data', you create from your programs on the 'data disk '.

  You can redirect your personal folders for the data stored there:

  How to redirect your personal Folders in Windows 7: Notebooks.com

• Strange problems from CC 2014 UI Illustrator

  Hello and sorry for my bad English! I have strange problems with Illustrator CC 2014 UI. Here are my specs:

  Kernel i7980x

  24 GB of DDR3 ram

  Asus P6tDeluxe mobo

  ASUS GTX 680 4 GB

  I'll post a grab to show what it looks like. It happens randomly while I'm working. Last GPU drivers and GPU performance is off (no changes).

  Thank you for your time,

  Roberto

  It sounds like a video driver issue, but it can also occur when another application interacts with the video driver somehow. I could start by restarting in Mode safe mode and see if Illustrator can handle the screen without these problems. If the game is played on your system, they can sometimes leave the GPU in a strange state.

  Hope this helps,

  Allen

• Error with iTunes in Windows 10

  So I have a strange problem.

  What is happening is iTunes opens (perhaps more slowly than normal? Unconfirmed), but will enter a strange state. This will be repeated at random, sometimes when the program starts immediately, other times, a few minutes after. It also leaves this State at random, often after a few minutes, but only for a millisecond. Rarely, it will leave for a few minutes. The only way that seems reliable to enter this State is to plug in my iPhone. The only way to leave he must have the Task Manager kill the program, and then reopen it.

  In this State, it will not meet order entries and seems to freeze, but Windows does not recognize it as an error of gel. It will also continue to play any song that was playing before its entry into the State, but not go to the next song, when it ends (it will be however if she leaves the State). If I am interested in another application, although in that State, I can hover over the iTunes toolbar icon and see the screen, but I can't go to iTunes.

  I'm sure it's a question of iTunes, as all my other applications work fine. Reinstalling does not solve the problem but (restart the computer between uninstall and reinstall). I'm kind of at a loss because I have no idea how to solve this problem.

  Details:

  iTunes Version: 12.4.1.6

  OS: Windows 10

  Hardware: ASUS GL551

  See excellent iTunes from turingtest2 for Windows troubleshooting guide at:

  Troubleshooting problems with iTunes for Windows updates

  General advice for troubleshooting when iTunes is unable to properly install (and reinstall or repair it does not) are to remove not only iTunes, but ALL the components, restart, remove the target installation files and reinstall.

• Satellite A300-1NO - Power Saver crashes

  Hello

  I get a fatal error when starting electric saver application, code 0 x 2

  I have a Satellite A300 1NO with Windows XP. When the energy saver tries to start it gives this error code and accidents. This happens with the installer to start too.

  Assuming that the cause is the lack of files required by power saver. What can we then these files?
  ProgFiles/Toshiba and its subfolders are intact. I deleted some files from windows dir, who seemed unused, and needles. for example. directories and temporary files. And I think, that it is possible that some useful files have been deleted accidentally.

  So, it is possible that the cause is missing some files in windows? Otherwise, I have no idea of what was happening here exactly...

  Post edited by: Emoryy

  Hello

  I ve page no idea why your Power Saver crashes but before install you any what Toshiba you tools should updated Win XP to the current state, and then you need to install the common Modules of the European of Toshiba.

  Common modules is an essential component of Windows systems.
  He will perform the other original programming from TOSHIBA to work properly.

  So uninstall the old Power Saver, clean the registry and operating system with a free tool (i.e. CCleaner), install common Modules, and Power Saver.

  Good bye

• Portege R930-122 - Toshiba VAP REGDB get impossible point Win7 Pro 64-bit

  The toshiba Portege R930-122 as value added package reports during installation regDB get point is not.

  Start, change or remove SW procedure leads report.
  Toshiba Flash cards program is installed, but allowing on deactivation function keys is no difference (not driving function keys).

  Toshiba accessibility reports: this system cannot make use of Toshiba accessibility.

  Function keys worked until I upgraded to some Toshiba and Intel video driver packages, but can't find that one is the cause.

  You happen to know where to look?

  Hello

  Without the good work Toshiba PPV, other software Toshiba would not work properly.
  It is important to get the PPV of work package before you start the installation of other software from Toshiba!

  From my point of view of a few you should update the Win 7 in the last State before starting the installation of the software. The Win 7 SP1 must be installed before using the additional software.

  I found some installation instructions and the correct order:

  Windows 7 SP1 of Win7
  .NET framework 4.0 [TRO]
  SW 9.3.0.1020 Chipset installation utility
  Intel Management Engine Interface 8.00.03.1427
  Intel AMT 8.00.03.1427 software
  Driver Intel 8.15.10.2712
  Intelligent management of the screen TOSHIBA v1.0.3.0
  Driver Intel Rapid Storage Technology 11.0.0.1032
  Technology of quick start Software Intel 1.0.0.1022
  ALPS Pointing Device Driver v7.x6.303.214
  Synaptics Touch Pad Driver 15.3.27.1
  Realtek Audio Driver 6.0.1.6591
  SRS Premium Sound 3D 1.12.1800
  Driver Intel LAN 16.8.46
  Intel Wireless LAN Driver 15.1.0.21.1
  Intel Proset 15.1.0.0.2.s32
  Intel Wireless Display 3.0.13.0
  Bluetooth Monitor v4.08
  Battery Bluetooth for Windows by Toshiba v9.00.03T
  USB3.0 Driver 2.1.28.0
  Intel USB3.0 Driver 1.0.4.220
  Ericsson 3 G driver 7.1.0.3
  Ericsson Wireless Manager 7.1.0.2
  O2Micro smart card reader driver
  Ricoh 2.15.17.02 card reader
  Driver USB-Serial V1.3.0
  TOSHIBA value added package 1.6.0027.320202
  TOSHIBA Fingerprint Utility V2.0.0.9
  TOSHIBA Web Camera Application V2.0.3.33
  PatchFiles PCIIDEREG - 1.2
  PatchFiles TosVolRegulator_1.1
  PatchFiles TBMINITREG-1. 0 t

• Satellite Pro U400 - network connection lost after suspend

  I have a Toshiba Dynadock. My network is connect directly in dynadock.

  When suspend my Satellite Pro U400 and after reboot to continue working I lost my network connection. Then I shut down my computer and disconnect/connect Dynadock I can continue working.

  What is the problem?
  Dynadock software version is 2.0

  Hello

  I see that you have switched from Vista to XP.

  First of all I recommend you update the BIOS.
  As I m not wrong on the European driver Toshiba page, you should find a newer version of the BIOS.

  You will need to upgrade Win XP to the last State.
  The XP must be up-to-date and all service packs, hotfixes and patches MS must be installed in your laptop.

  Access the Device Manager, and then score in each USB hub root, you must disable the option called allow the computer to turn off this device to save power
  You can find this option in the properties-> tab power management

• Camileo S20 - my PC cannot read the 8 GB SD card

  I have a Camileo S20 Pocket camcorder, using a Kodak 8 GB SDHC card. I can't read this card using two Dell PC.

  I have a SDHC card reader and it can read a 4 GB SD card, card, but not the 8 GB card.

  Would it be the high definition HD format video and images that is the problem?
  If this is the case, what can download to fix this problem.

  Gary

  Hello

  I put t think that this issue has something to do with the HD format on the SD card.
  As you say, the 4 GB card can be used properly and the card of 8 GB does not work.

  So I think that the card reader is not compatible with the 8 GB SD cards.
  In this case, I recommend buying an external card reader what 8 GB support card that could be connected to the usb port.

  It could also be a problem with Win XP if you are using Win XP.
  In this case, you will need to upgrade win xp to the last State and need to install a patch http://support.microsoft.com/kb/934428/en-us

• Satellite L300 loses the IP address using the WiFi network

  Hello

  I recently bought a Satellite L300 and installed Windows XP. While I installed all the devices available for download drivers my wireless connection is still not working properly - the IP address shows as lost after several minutes of functioning and on several occasions the laptop froze and had to manually turn off (if the wireless connection is turned off to this isn't the case)

  You have ideas or suggestions on why this is happening?

  Thanks in advance for your support!

  Hello

  Check if the most recent BIOS is available for this model of laptop and if yes, then try to update.
  As next update Win XP to the last State. All MS patches, updates must be installed.

  I m not very well what WLan card you but you are trying to install the WiFi adapter driver on the WLan card manufacturer site.

  Finally, and especially if you lose the WLan IP address and then start the CMD (in the window RUN) and type this command:
  ipconfig / renew

  Check it out!

• Satellite p300-212 problems after downgrade to xp (yellow? and!)

  Hello

  I had the same problem as the guy FOM this thread---> [http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=174977𪮁 | http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=174977𪮁]
  I lowered my Satellite P300-212 from Vista to XP. I used an installation Win XP CD of Win professional XP including Service Pack 3.
  Then I installed all the drivers from the Toshiba site.
  But I still have a yellow! in the Device Manager to the "Audio device on High Definition Bus". The details of this device show "HDAUDIO\FUNC_01 & VEN_1002 & DEV_AA01 & SUBSYS_00AA0100 & REV_1001\5 & 3B6F18F1 & 0 & 0001"
  So I don't know, what driver I need to take to solve this problem. Rather, modemdriver etc are all installed and work fine!
  In the thread I linked above, the guy only has not copied driver WICH he installed manually. :(

  I hope that someone of you can help!

  Best wishes.

  greatwolfman

  Hello

  You should go to remove device manager and scream this device with the yellow! and?
  Restart the unit.

  In addition you must update Win XP for the last State because there are many patches that are required under Win XP latest series laptop.

• Satellite P100-347 - DVD player is no longer visible in Windows XP MCE

  Hello. My DVD players seems to have disappeared from within Windows MCE running on my P100-347. BIOS can see it, it opens and closes without any problems and the light comes on as if the disc is read, but it is not considered by Windows as a disc.

  I installed the DVD - RAM drivers on the Toshiba site, but this did not a bit of difference. Any suggestions?

  Hello

  Have you checked STRANGE State in the Device Manager?
  Some yellow exclamation points appear in Device Manager?
  Could you please give some info on the error message?

  I found this useful Microsoft Knowledge base article:
  http://support.Microsoft.com/kb/314060/en-us/

  Maybe it helps.

• Satellite U200-165: card reader do not read MMC cards but SD reading card

  Computer laptop Satellite U200-165, Win XP home,
  I got in 2006, while it wasn't any problem with my mmc cards.
  Yesterday installed Windows XP pro, installed the drivers: driver media flash and SD Secure module and card readers do not read MMC cards

  Help, please!

  Hello

  What exactly do you mean by MMC card doesn t work?
  What is the status of card reader in Device Manager?

  I checked the user manual (which can be downloaded from the Toshiba page) and it tells the MMC cards are certainly supported.
  I think it must be a software problem.

  In your case I recommend to update the Win XP for the last State and reinstall the Flash Media Driver and SD Secure Module again