Windows 10 iMac 27 "el capitian Boot camp Installer could not move forward and the black screen appeared

Similar Questions

• Boot camp: drive could not be partitioned

  I tried to install win 7 on my Imac to 2013.

  When boot camp tried to partition my drive for the first time, it freezes and I had to reboot.

  When I got to the I tried it again, I get the message: disk cannot be partitioned.

  What can I do now?

  Tell us what the error message says.

• Error code: 1601 Windows Installer could not be accessed during the installation of Turbo Tax 2009.

  I try to install Turbo Tax 2009 on a Dell Inspiron 530.  I get the message that Windows Installer could not be accessed.  I tried all the fixes I could find and nothing works.

  When I try to install install 4.5 Redistributable, a dialog box appears saying "the update does not apply to your system" no matter which I choose in the list to download.

  What is going on?

  It comes with Vista, upgrade install and activate Forum.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/threads

  Try the repost in the Forum Vista programs at the above address.

  They will help.

  See you soon. Mick Murphy - Microsoft partner

• iMac 2015 Unable to Boot Camp and Windows Installer

  I've been back and forth with a Service guy to customers by phone, but thought I'd throw so the question in the case to see if there were others who have experienced similar problems and might be able to help.

  I have an iMac, retina 5K, 27 - in, end of 2014. It allows to launch the Boot Camp with Windows 8.1, which I put in place about 1 year ago. It worked very well. But then, I decided to try to upgrade to Windows 10 about 3 weeks, which is not well. Decided to erase the partition via the wizard Boot Camp and re - install from scratch.

  Now, I can not install Windows at all. I've tried everything. Using another ISO downloaded from the Windows website. Check disks using first aid. Last night I even totally erased the readers (via the terminal in recovery mode, with the help of the man of CS) and made a "Reinstall internet" of the operating system and then tried in boot camp. Without success.

  I tried to call Microsoft too, but their position on the whole thing is "this is on a Mac, this is the problem to Apple. Bye. »

  Appearances, Assistant Boot Camp is successfully created a partition. The system resets the Windows installation each time and I spend the flow rate of the installation until I get to the section "where you want to install Windows? I select my Bootcamp partition, format and then click Next. That's when I get the error message "we could not create a new partition or locate an existing one. For more information, see the Setup logs files. »

  If I quit the installer and restart on the side OSX, I see that the new partitions is to Windows NTFS, so it seems ok. I am completely puzzled and frustrated as * at this stage.

  Any thoughts? Ideas? Help? Please?

  Data sheet:

  iMac (retina 5K, 27 inches, end of 2014)

  4 GHz of Intel Core i7 processor

  16GB 1600 MHz DDR3 memory

  AMD Radeon R9M295X graphics 4096 MB

  What are the external devices connected to the iMac during the installation of Windows?

  See also Boot Camp: "we could not create a new partition or locate one" alert during the installation of Windows 8 - Apple Support .

• Windows 10 can be installed on Boot Camp Version 4.1

  Hello

  Windows 10 can be installed on Boot Camp Version 4.1? Whenever I do a page search thishappens which show how update but I have read that Windows 10 requires an updated Boot Camp (v6).

  Or better yet 6 Boot Camp out again? If so, how do I update my Boot Camp?

  FYI: that's what I did to get the version of Boot Camp, I went to my Windows partition click on icon Boot Camp and click on the button on Boot Camp and I got 4.1.

  I'm running Windows 7 on Mac OSX El Capitan.

  Any advice?

  If you already have installed W7 you can pass up to W10. Bootcamp may be necessary if you need to re - install W10. If your model of Mac is not listed in the link you found, Apple does not officially support W10 on your Mac, which means that there is no W10 driver certified for your model of Mac.

• I installed windows 7 on a mac with boot camp and then used parallels to create a virtual machine to run windows inside Mac os10.6. Now he says I need to activate windows again, but he said I need a new activation key. Any ideas would be appreciated

  I installed windows 7 on a mac with boot camp and then used parallels to create a virtual machine to run windows inside Mac os10.6.  Now he says I need to activate windows again, but he said I need a new activation key.  Any ideas would be appreciated

  Yes, you must purchase a full license for the second installation of Windows 7 product key.  1 activation allows only one Windows 7 product key.  Apparently, you now have a second facility that requires a second product key. Carey Frisch

• Windows 10 boots and stuck on the black screen with high CPU

  Hello

  I have a MBP 15 "mid 2015 16G with AMD R9 M370X i7.

  I've been running bootcamp with Windows 10 installation for about a month now without any problems.  However, yesterday 10 Windows started and has been blocked in a black screen (before any screen logo or connection win) with the CPU works hard and hot.

  1. I tried to restart some time hold button / stop and start with the option key, key and then selecting the windows bootcamp partition but it drove the same black screen with CPU hot work in the background.

  2. I can always start OSX fine during this period.

  3. I tried to leave in the black screen for a good 10 minutes, but it does not change and the MBP gets really hot.

  4. I tried clearing NVRAM with Boot option + command + P + R

  5 I can't in Windows 10 safe mode using F8 or FN + F8 after you select windows to boot manager (starting with the down option).  Am I missing something here?

  I don't have a copy of Installer windows 10 with me right now unless someone can tell me how to create one under OSX.

  I searched on the internet forum and apple, but have not found a solution that works for me.  Many speak of win10 black screen with cursor showing, but my question is just a black screen with no cursor.

  Someone at - it other ideas besides reinstall Windows 10?

  You have a black screen with or without power adapter, both? If 10 Windows does not start correctly three times, it should bring up the recovery console. Windows automatic updates are enabled? You have created/activated Windows system restore points?

• Given to nine Compaq 7700, BSoD, boot XP infinite loop, can't even get past the black screen to enter Windows. STOP: 0X0000007E (0XC0000005, 0XF773B15F, 0XF78D2520, 0XF78D221C)

  Help.

  I just got a refurbished Compaq 7700. It has Windows XP for drives of the refurbished computers.

  I try to boot from the hard drive (HD) and infinite loops, it is never past the initial home screen (black with blue status bar).

  I can't open the safe or the HD mode, it freezes at kmxstart.sys and then restarts again.

  Original title: given to nine Compaq 7700, BSoD, boot XP infinite loop, can't even get past the black screen, to enter Windows.

  I tried to boot from the disk and created Windows appears, then load the files, but then automatically tries to start Windows (without repair option). It then jumps to the BSoD with error code (after advice to verify sufficient disk space, to disable the driver identified, to change video cards, BIOS updates...)

  STOP: 0X0000007E (0XC0000005, 0XF773B15F, 0XF78D2520, 0XF78D221C)

  Usbccgp.sys - address F773B15F base at F7737000, DateStamp 480254d 2

  Apparently, this driver is a printer driver? I don't have a printer, but do not know how to disable it without access to windows.

  I got a new Philips 18.5 "monitor, an optical mouse and a keyboard with it.

  My guess is that the screen is the problem, because it was full again when I received and therefore not tested with the system before shipping. Not sure about the mouse and the keyboard.

  I tried a few options in the BIOS screen as well, but no dice.

  Help! Before shipping the brand new...

  I thank you and have a wonderful new year.

  Craig.

  Howdy Daavee and Shekhar,

  I hope that your day is going well.

  It turns out that it was the hard drive, it was defective. The new unit arrived and it works beautifully. Thank you very much for all you help. I wish you a happy new year.

  Craig.

• Vista OS does not load. I tried booting and the load screen bar continues to work without success. When you run the start he stops to c:\windows\system 32\cmd.exe that I don't want to lose my files so I have not reinstalled. Any suggestions?

  Vista OS does not load.  I tried booting and the load screen bar continues to work without success.  When you run the start he stops to c:\windows\system 32\cmd.exe that I don't want to lose my files so I have not reinstalled.  Any suggestions?

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery, if/before you reinstall:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• Marketing, Windows XP displays "error loading msinuc32.dll specified module could not be found.

  While starting up, Windows XP displays "Error loading msinuc32.dll specified module could not be found" help me solve

  Hi Rahmansherif,

  ·         Did you do changes on the computer before the show?

  Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click restart to restart the computer.

• ACPI.sys corrupted at startup disk on the black screen windows

  When I start my computer normally all I get is a black screen with my cursor on it before I reach the log on screen (but after normal of the windows startup process).  I tried Ctrl alt del and nothing happens, there is no beep or anything along those lines is.  I tried safe mode, but exactly the same thing happens, I get a black screen with white inscription around the edges, telling me that I'm in safe mode and my slider is still there and moves, but other then that is all black screen.  Ctrl alt delete doesn't work or any other key press on that I skipped.  I put in my windows XP CD and he would try to repair or reinstall the operating system but when I boot on the CD, it starts to load normally and then stops and gives me the error message "the acpi.sys file is corrupted.  Press a key to continue' when I press any button it goes upwards and brings back me to the black screen with the cursor.  I tried to go into the BIOS and turn off acpi but the loading and the startup disk produce the exact same results any bios settings I try.  Any help would be appreciated, either for obtaining windows at startup after the black screen without the startup disk or get me to the point where I can still use the CD (which I should mention that I have used before and it worked well, is the one responsible for my windows XP in the first place and who is clean and scratch free).  Thank you for any help or advice.  Oh, and I must add that I have installed any new software or whatever it is like in the last month or two, so I don't think it is something like that.

  Hello usernamerandom,

  Take a look at the sticky thread depending on which was released 21:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/why-do-i-have-a-black-screen-when-i-start-Windows/ddf978da-4ba1-49dc-8844-2407c3fc1c82

  Best regards

  Matthew_Ha

• My Windows telling me that he needs 11 updates. These updates consistently fail and the Microsoft fix did not work. Error codes are 641 and 80070641

  My Windows telling me that he needs 11 updates.  These consistenly updates fail and the Microsoft fix did not work.  Error codes are 641 and 80070641.

  Hello

  Did you change your computer before this problem?

  You can follow the suggestions and check out them.

  Method 1

  You can follow the procedure in the article.

  How to resolve problems connecting to Windows Update or Microsoft Update

  http://support.Microsoft.com/kb/818018

  Method 2

  You can reset the Windows Update components.

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.
  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Method 3

  You can download and run the system update readiness tool.

  Description of the update tool of the system to Windows Vista, Windows Server 2008, Windows Server 2008 R2
  http://support.Microsoft.com/kb/947821

  Method 4

  Step 1:

  Place the computer in a clean boot state.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a troubleshooting follow step 7: reset the computer to start as usual

  Step 2:

  You can manually download and install updates from Microsoft Download Center.

  Microsoft Download Center

  http://www.Microsoft.com/downloads/en/default.aspx

  Method 5

  You can disable temporary of your security software.

  Disable the antivirus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks

  See also:

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

• Get the black screen at boot: status: 0xc000000f

  Original title: status: 0xc000000f

  I get a black screen when I turn on my laptop (Windows Boot Manager)

  Windows could not start.  A recent hardware or software change might be the cause.  To solve the problem:

  1. Insert your windows installation disc and restart your computer.

  2. choose your language settings, and then click "next".

  3. click on "Repair your computer."

  I followed all the instructions and still it will not read the installation disc.

  I put in the disk and restart the computer, but it brings back me to the same black screen.

  File: \Windows\system32\winload.exe

  Status: 0xc000000f

  Info: The selected entry could not be loaded because the application is missing or damaged.

  Can someone help me with this question to where it will read the disc. or what I am doing wrong?

  I got Appreciate your help :)

  Ok.

  You can watch the image here - is your BIOS looks in this picture:

  https://SkyDrive.live.com/#CID=23FD66EFD8D06B76&ID=23FD66EFD8D06B76%21177

  If so you can try everything first:

  (1) turn on (or restart) your office

  (2) press on instead of - you should see "Start menu", where you must select "Drive of CD-ROM.

  If does not work (this means no "Boot menu" only appeared), then you need to change "Boot Device Priority" - go into the SETUP (   course of priming of the desktop), use the right arrow to select 'Boot' (upper image) - use the down arrow to select "Boot Device Priority" and press enter - you should see something as shown in the photo at the bottom.

  Now choose "Drive of CD-ROM" (arrow down) and by using the key + or - move the first CD-ROM drive. Press on (save & exit).

  Use this DVD:

  1. MICROSOFT WINDOWS VISTA HOME PREMIUM SP1 X 86

  LC

• Windows Vista will not start up - keep getting the black screen

  I read through the questions answered similar questions and still can not past the black screen with windows vista.  It's on a dell inspiron 1525.  Also, it does not start in safe mode and I tried booting from the last good configuration and is still stuck on the black screen.  This just started a few days ago, and the computer was working fine until this date.  Can you help me?

  Hi Jimazona,
   
  1. from when are you facing this problem?
  2. any change in software or new hardware on your computer?
    
  Method 1:
    
  First of all I suggest you to disconnect all devices external one except keyboard and mouse and try to start your computer and check.
       
  Method 2:
      
  I also suggest you perform a startup repair and check if this solves the problem.
     
  Follow the steps below:
     
  a. Please insert the Windows Vista DVD and restart the computer.
  b. when we are asked to press a key to boot from the DVD, please press enter or the SPACEBAR.
  c. Select your language settings, and then click Next.
  d. click on repair your computer.
  e. Select the operating system you want to repair, and then click Next.
  f. in the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.
   
  Access the link below for more information on the Startup Repair:
  Startup Repair: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions
   
  See also:
   
  http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/24b44a01-872e-4d87-867f-ed01a3579031/   
   
  I would like hearing that the results back on your part about what happened after trying each method.

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think. 
  

• I got the black screen of death & now im getting disk boot failure, insert system disk

  original title: I had the black screen of death & now im getting disk boot failuer, insert the system saying

  I got the black screen of death & now failure boot disk, insert the system disk, which I don't have. Help.

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  and if all else fails and you need to reinstall vista are the normal methods for computers preinstalled vista portable

  Contact the computer manufacturer and ask them to send vista recovery discs

  they do it for a nominal cost of $

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F10 or F11 or Alt + F10, 0 at startup to start the recovery process according to the manufacturer

  Ask them of the exact key sequence