Windows 10 tiles start and Persona management

Similar Questions

• I get windows did not start and each time that I reboot I get the same thing.

  * Original title: Windows7

  O my pc displays a boot device error so I put in a disk hard new1tb and reinstalled Windows 7 and install goes ok just a little slow, but after the installation is completed after the first reboot I get windows did not start and evry time I reboot I get the same thing tried several hard drives and get the same error not sure of the material cause I can load in the bios very well any help would be great

  In addition:

  Clear CMOS - 3 ways to clear the CMOS - reset the BIOS

  The setup of the BIOS or UEFI firmware, search for UEFI settings so that you can follow special steps to install UEFI below.  Also set SATA controller on AHCI, hard drive, all on first start (or if UEFI Boot Manager WIndows).

  Then just follow these steps for a clean reinstall Windows 7 making sure to remove all partitions up to unallocated space to make it cleaner.   Follow special steps if you have a UEFI BIOS, which will have a system partition EFI in Managment of disk instead of reserved system (MBR) and make sure that the SATA controller is set to AHCI.

  Other important to overcome optmizations install them hedges here to resolve the failures of Windows Installation 7

• Virus on Windows, does not start and he said: no operating system or it is corrupt

  Original title: help please

  I have a laptop with windows vista. Apparently, someone in the House caught a virus.  now windows will not start and he said: I have no operating system or it is corrupted. can not even boot in safe mode or anything.  says windows error recovery screen when turned on.  any help is appreciated.

  Hi Lawry206,

  You can try the following steps and check if it helps.

  Method 1: Disconnect external devices attached to the computer and restart to check the issue.

  Method 2:

  Since you are unable to start the computer in safe mode, you try to perform a repair to start the Windows recovery environment (WINRE Mode) and check if it helps to solve the problem.

  You need start from your Installion of Windows Vista disc.

  If startup repair does not help, then try a restore of the system of the WINRE Mode and check.

  You can see the following link for more information.

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

• My windows 8 not start and there is no administrator account

  My windows will not start and I can't fix with restore point or safe mode because there is no found administrator account

  Hello

  Thanks for posting your query to the Microsoft forum.

  I understand the inconvenience caused to you. I will certainly help you in this matter.

  1. You have the administrator password?
  2. Have you ever had the administrator account on this computer?

  In order to fix your computer, we should have an administrator account through which we can perform the appropriate troubleshooting.

  If you have the administrator password, boot the computer through DVD and enter safe mode with command prompt, this will require the administrator password, enter it.

  Mode safe mode with command prompt

  http://Windows.Microsoft.com/en-in/Windows-8/Windows-startup-settings-safe-mode

  If you are able to access the prompt try to activate the hidden administrator account and create a new administrator account.

  1. At the command prompt, type net user administrator / Active: Yes , then press on ENTER.
  2. Type net user administrator , then press on ENTER. Note: Please replace the tag with your passwords you want to set for the administrator account.
  3. Type exitand press enter.
  4. Restart the computer.

  Now, try to create a new Local Administrator account

  Once done, you can now disable the build-in the administrator account.

  Follow these steps:

  1. click the button Start , and then type cmd in the search box.

  2. in the list of research results, right click on cmd and then click on Run as Administrator.

  3. at the command prompt, type net user administrator / active: no and then press ENTER.

  4. type net user administrator , then press on ENTER.

  Note: restart the computer to make the changes.

  If you do not have the DVD of Windows 8.1, I suggest to download and create a bootable media and perform operations.

  Refer to this link: create installation media for Windows 8.1

  Please post back with the results and the information requested, we will be happy to help you further.

  _____________________

  Thank you best regards &,.

  Isha Soni

• Windows, clones and persona management saved credentials

  Hi all

  We have an infrastructure of clone of work with Persona management put in place. Everything works very well only our users complain that their windows credentials are not saved to a network share that they use, what is actually the case: once you change the clones, even though you checked to remind the credentials box, your windows password safe is empty and the credentials must be entered again to access the remote share.

  I looked around, I found this KB:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 2052573

  As I understand it, touring credentials is not supported, and this can be done. Which, I guess, sort of logic.

  However, I came across this post on the forum:

  Finds support in the management of Persona to CryptProtectData

  Where is the original says that "View Persona Manager does support the Windows API data protection.' poster.

  I'm confused here: is it possible to wander the credentials for network shares or not? If so, how this reach you? If not, is it final or is it planned to get this working?

  Thanks for your comments,

  Marc

  For everyone wondering the same thing and do not find an answer, upgrading the client to view the clones to 6.0.1 fixed the problem.

• Windows will not start and automatic repair does nothing

  Hello
  I am on Windows 8 on my desk of game and encountered problems with the start-up. Whenever I try to start the computer, it does this:
  (1) prepare the auto repair

  (2) diagnose your PC
  (3) auto repair couldn't fix your PC
  Whenever I try to click on anything in the advanced options it says I need to sign as an administrator but no accounts are displayed. He then tells me to restart my PC that starts the whole cycle again.
  Is there a solution to this problem? I really prefer NOT wipe the hard drive clean as I already downloaded more than 200 GB of Steam games in the past few months and only have 35 GB per month to redownload the.

  Hi Hazza,

  Thank you for the update.

  When you perform a custom Windows installation, Windows creates a Windows.old folder that contains your previous system files. You can retrieve your personal files from the Windows.old folder and move them to the customized Windows installation.

  You can view the following for more information Microsoft article.

  How to recover files from the Windows.old folder

  It will be useful.

• Windows will not start and cannot enter the safe recovery mode

  Had a blue screen and when I start Windows wants to run in safe mode. But this takes place for a few seconds and then stops with a blank screen (this is for more than 2 hours).
  If I choose to start windows normally the system reboots just to repair windows screen.

  I'm not a Windows vista recovery disc has been pre-installed. Clues?

  Hello

  The reason is that Windows bootmanager or system files are corrupt. You say that you did a recovery disk, but what image of hard drive recovery (by pressing F8 at startup)? If it is already deleted, you must:

  1. order the recovery disk https://backupmedia.toshiba.eu/landing.aspx Note, it is not free
  2 a copy of Windows vista and install it. Then, download all the required drivers and enjoy.

  Welcome them

• my windows xp computer started and gave me a new identity. all my files are missing. Is it possible to recover them? The programs are still on the system.

  The computer worked fine last night.  This morning, after entering the password journal, xp started up the generic wallpaper and invited me to learn the features of windows xp.  the programs seem to work.

  Looks like your user profile is damaged.  I hope that you do not use the built-in account named "Administrator".

  If the administrator account is not corrupted, it is available in XP Home restarting the computer in Mode safe.  In XP Pro, you can get on behalf of administrator mode without failure or by pressing CTRL-ALT-DEL twice at the 'Welcome' screen.

  Assuming that you can get an account with administrator privileges, administrator or another account that you have created and which has administrator privileges, see http://support.microsoft.com/kb/811151

• What can I do if Windows does not start and system repair will not work

  Original title: pc does not start. blue screen says driver overtaking has a stack buffer and of physical memory dumps. repair of the proven system and also the restoration of the system. still no luck. Help please! Jane.

  Blue screen flashes off pretty quick so cannot read all of it. It says problem can be installed recently ware. don't the have not installed anything. Since regular programs.

  says a malicious attempt can occur. that security essentials update installed.  Windows system repair ran several times and said that he could not fix pc. Just tried restoring the system to the 22/10/11, which said it was successful, but still have the same problem. Don't know what to do now that not that computer savvy!

  Hello

  Did you do changes on the computer before the show?

  Method 1:
  You can disable automatic reboot system Advanced Start Menu fails to capture the error message and check if it helps.

  Method 2:

  You can start the computer in safe mode and check if you are able to start
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 3:
  If you are able to boot into safe mode, then perform a clean boot and check:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the Knowledge Base article.

  Method 4:
  You can perform system restore and startup using Windows vista DVD repair.

  What are the system recovery options?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

• What should I do if my windows does not start, and the Startup Repair is not help at all

  So today, I went and when I turned on my computer from sleep mode, it was perfectly fine.  I was watching a video, surf on internet and MSN messenger when my computer froze all of a sudden.  I waited for release, but it didn't.  Given that I could not turn off the computer either, I had no choice but to disconnect it from the computer.  However, later, when I tried to restart, the screen would go black after the black loading screen.  Subsequently, it would just restart and startup repair would begin.  I tried to restore Systen and ran several times startup repair.  In addition, it does not even boot mode safe.  Here are the details of the problem for the Startup Repair:
   
  Problem event name: Startup repairV2

  Signature of the problem 01: AutoFailover

  Prob Sig 02: 6.0.6001.18000.6.0.6001.18000

  Prob Sig 03:5

  Prob GIS 04:393220

  Prob Sig 05: NoRootCause

  Prob Sig 06: NoRootCause

  Prob GIS 07:0

  Prob GIS 08: 1

  Prob Sig 09: SystemRestore

  
  Prob GIS 10:0

  OS version: 6.0.6001.2.1.0.256.1
  Local ID: 1033

  Please help me find a way to restart the computer without having to reinstall Windows because I don't have a back-uped none of my files, so I would lose everything...

   
  Thank you
  Jeremy

  Hello

  ·         How have you tried to do system restore?

  I recommend you to restore system using a Windows Vista DVD.

  Here's how:

  To open the Options menu system recovery using a system repair disc or a Windows Vista installation disc

  If your system is damaged and cannot access the menu system on your computer Recovery Options, you can access it using the Windows Vista installation disc or a system repair disc previously.

  To use this method, you need to restart (boot) your computer using the disk.
  1 insert the disc.
  2. restart your computer using the power button on the computer.
  3. If you are prompted, press any key to start Windows from the installation disc.
  If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer.

  4. choose your language settings, and then click Next.
  5. If you are using the Windows installation disc, click on repair your computer.
  6. Select the Windows installation you want to repair, and then click Next.
  7. in the System Recovery Options menu, click a tool to open it.

• Windows will not start and repair failed. Can I upgrade to Windows 7 from this situation and get Windows 7 to begin?

  Any help will be apprecdiated.

  Normally, you do an upgrade from the inside of the race and activated the operating system.

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows will not start and repair functions do not work

  Hello!

  A few days ago when I turned on my laptop, it said 'unable to start Windows. A recent hardware or software change might be the cause. «I tried to solve the problem through the installation and repair of computer disk, but the startup repair does not seem to do anything be said "Startup Repair couldn't fix your PC (it ran four times), System Restore cannot find a restore point (sometimes he says that I have to specify which Windows installation to restore the good I don't have one) and refresh your PC says that the» drive is locked. Furthermore, each operation in the repair of your computer takes really long, on one or two hours. It's Windows 7 Ultimate x 64, I'm talking about.

  In addition, I can not in safe mode as button by pressing f8 (or f5) ends with a sound signal and guest starts with x:\sources instead of c:\windows so minimal safeboot / network does not work.

  I also tried to use explorer.exe to copy the most urgent files to a usb flash drive, but it does not display the files in c:.

  Any ideas?

  Thank you and best regards.

  I suspect that you need to perform a destructive factory restore. Here are a few options to recover your files:

  • From your external backup. If you do not have an external backup, then this is a great time to review your backup strategy.
  • By starting the machine Mode of repair of Windows, and then using the console commands to copy your files to a flash drive. Post again if you need help with these commands.
  • By starting the machine with a boot of Ubuntu CD, then drag your folders to a flash drive.
  • By removing the hard drive and plugging it into another PC. Use a SATA cable if it is a drive 3.5 "or a USB enclosure so it's a 2.5 drive".

  The above methods are much more time that executing regular backups on a backup drive GByte 1 costs about $60.

• Windows does not start and color distortion

  Hello

  I need help, my computer won't start, just at the windows startup screen and my computer colors are skewed

  Help, please

  PS. I use another computer.

  Hello

  I need help, my computer won't start, just at the starting windows screen and my computer colors are distorted

  Help, please

  PS. I use another computer.

  Hello

  It is normally a sign of the corrupt graphics drivers, but that your machine does not start in Windows, it can be a sign of not having a graphic material.

  See you soon.

• I don't have an error code. I play Aion with windows 7, it starts and runs really nice on max settings. The problem is that the computer shut down just when he wants to without error or explanation please help.

  Is there a way to know why your pc stops the poeople HP say this is a problem of windows 7 and can not help.

  It could be that the computer is running a little on the hot side and the thermal protection has kicked. One of the down sides to get a pre-generated computer who is yo have no control over the thermal limits. Try to blow out the dust accumulated inside the computer, just him ensure that the computer is turned off and unplugged before you open the side of your computer. You might need a couple of compressed air or one of these mini vacuum computer systems that can act as a fan as well. I hope this helps.

• After installing Lightroom 10 CC 2015, Photoshop CC 2015 windows does not start and Illustrator CC 2015 freezes after startup. It look like that the program (or maybe add ons) need to dll of the CC + 2008 with isn't so more recordable in Windows 10

  Has anyone have the same problem and maybe a Solution?

  Hey mksuperplus,

  Please check this link Windows 10 update breaks Microsoft Adobe CC - missing - MSVCR110.dll community for the solution.

  Kind regards

  Nicos