Windows 8 Wifi doesn't have a valid IP configuration

Similar Questions

• WiFi doesn't have a valid IP configuration for windows 8

  I bought a computer dell laptop with integrated windows 8 last week.

  The wifi worked for a few days and then all of a sudden it stopped. It shows connected wireless but no internet access.
  Back to diagnose the problem, message foll...
  WiFi doesn't have a valid IP configuration...
  Wifi works fine on others - phone, I - pad except this laptop.
  Pls adv how can I do to solve this. I talked to the provider, but according to him, this is a problem with the router and not the laptop.
  I saw a lot of similar problems on this community as well.

  First of all your router off/on power supply and see if that fixes it.

  If this is not the case, connect to your router and make sure that DHCP is configured to allow enough IP for all your devices.  I've seen where people had set for a range of 5 devices when they arrived the router, keeping it years later, make it have more devices with smart TV, etc.

• WiFi doesn't have a valid ip configuration

  I have recently installed windows 8.1 and I was not able to connect to the internet since then. I tried different remedies, I searched on various forums such as using the command prompt, netsh winsock reset catalog and even tried netsh int ip reset reset.log hit , high ipconfig / renew andipconfig/release . But still nothing. I also tried to delete AVG, but still nothing. I'm sure that its also not a router related issue as all the other computers in my home connect to wifi and on top of that, I tried to connect the laptop to different routers and still nothing.

  Hi Ben Hmida,.

  I appreciate the efforts to try to solve the problem. If there is an IP address conflict you might face this problem. You can try to manually assign it the IP address and see if it helps.

  Set the IP address manually.

  1. Right click on the network icon located in the lower right of the screen, and then click Open Network and Sharing Center.
  2. Click change settings card present on the left side of the screen.
  3. In the Properties window for the Ethernet, select Protocol Internet Version 4 (TCP/IPv4) , and then click Properties.
  4. Click the radio button next to use the following IP address.
  5. It will give boxes to enter the IP address, you can type the address, for example, if you have a number of machines begin by setting the IP 192.168.1.100 then go to 192.168.1.101.
  6. The subnet mask has the default value is 255. 255. 255. 0 in most cases.
  7. Copy the default gateway of the network connection details window information.
  8. Copies information from DNS server in the details window - there will probably be two addresses to copy. Refer to the image given below to

  

  9. close all windows and test your internet connection.

  You can also see the steps in the link below.

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-8

  Write to us at the State of the question. We will help you to come.

• "Ethernet" doesn't have a valid IP configuration!

  Apparently, a lot of people have had this same problem with the pre-release of windows 8. None of these solutions have worked for me. I use the overview of the developer to win 8 and still getting the same problem.

  In fact, the problem is that I can't access the internet via my wired Ethernet interface. I have a Realtek PCIe network card using the version 7.3.522.2009 of the driver in compatibility mode for Windows 8. I tried all the possible drivers available for the card and the problem persists, while the same card works fine with my Windows Vista. I am able to access the internet via my wireless adapter, but not via the Ethernet card. When I troubleshoot the network card it gives me just the error that "Ethernet doesn't have a valid IP configuration".
  The thing is that my network card is not able to automatically acquire an IP address, even if the DHCP client is active and running. I tried to use
  • ipconfig / renew
  • netsh int ip reset c:\resetlog.txt

  and similar things, but none of them worked. I think I tried literally everything possible to operate before posting here. I hope that someone of you can help me. Really looking forward to y. Thank you.

  Mandatory ipconfig/all is given below
  C:\Windows\System32>ipconfig/all

  Windows IP configuration

  Name of the host...: Qutab-PC

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  ... DNS suffix search list: tontut.fi

  Ethernet Ethernet adapter:

  The connection-specific DNS suffix. :

  Description...: Realtek PCIe FE Family Controller #2

  Physical address.... : 00-00-00-00-00-00

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::e95c:a986:9d:2ba2% 20 (Preferred)

  Autoconfiguration IPv4 address. . : 169.254.43.162 (Preferred)

  ... Subnet mask: 255.255.0.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 335544320

  DHCPv6 DUID customer...: 00-01-00-01-18-6D-0E-A0-00-24-2C-18-84-39

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Bluetooth network connection Ethernet card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Device Bluetooth (personal area network)

  Physical address.... : 00-24-7E-4C-58-26

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Local Area Connection wireless LAN adapter * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Microsoft Hosted network virtual card

  Physical address.... : 12-24-2C-18-84-39

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Wi - Fi wireless LAN adapter:

  The connection-specific DNS suffix. : tontut.fi

  ... Description: Qualcomm Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-24-2C-18-84-39

  Active DHCP...
  . : Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::61c7:6041:3469:cce8% 12 (Preferred)
  IPv4 address...: 94.237.67.97 (Preferred)
  ... Subnet mask: 255.255.252.0.
  Lease obtained...: Friday, December 28, 2012 10:01:29
  End of the lease...: Friday, December 28, 2012 14:58:02
  ... Default gateway. : 94.237.64.1.
  DHCP server...: 94.237.0.29
  DHCPv6 IOOKING...: 251667500
  DHCPv6 DUID customer...
  . : 00-01-00-01-18-6D-0E-A0-00-24-2C-18-84-39
  DNS servers...: 94.237.0.27
  94.237.0.26
  NetBIOS over TCP/IP...: enabled
  Tunnel adapter isatap. {EBBD9402-654E-4A1C-898F-33188E1CB182}:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Tunnel adapter ISATAP.tontut.fi:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. : tontut.fi
  ... Description: Adapter Microsoft ISATAP #2
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card adapt 6TO4 tunnel:
  The connection-specific DNS suffix. : tontut.fi
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2002:5eed:4361:5eed:4361 (Preferred)
  ... Default gateway. : 2002:c058:6301:
  2002:C058:6301:C058:6301
  DNS servers...: 94.237.0.27
  94.237.0.26
  NetBIOS over TCP/IP...: disabled
  Card tunnel Teredo Tunneling Pseudo-Interface:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  OK guys, I solved the problem! I post here if it helps someone who has a similar problem. I still don't know what was the main problem, but he probably was the pilot.

  So here's what I did to get rid of the problem
  1. Disable all IPv6 traffic (my ISP supports IPv6, so no need to turn it on). A very good link I followed to achieve this--> http://www.techunboxed.com/2012/08/how-to-disable-ipv6-in-windows-8.html
  2. Disable Microsoft Kernel Debug network card, which mysteriously appeared in my device manager. link to follow-> http://answers.microsoft.com/en-us/windows/forum/windows_8-networking/what-is-microsoft-kernel-debug-network-adapter/f72b8408-e4f7-4593-9e18-8cbb3e38a5ad
  3. I noticed that despite the fact that there is no physical address assigned to my NIC (probably a driver problem?), so I assigned a random MAC to my Ethernet interface using a mac generator. Link for the tool--> http://download.cnet.com/Technitium-MAC-Address-Changer/3000-2085_4-10554920.html
  4. Connected to the internet via the Ethernet interface!

  It will be useful.

• "Connecting to LAN" doesn't have a valid IP configuration

  Yesterday I just internet browsing and all of a sudden my connection died. I check on my ethernet connection and he says that he is not identified. I started to get many fixes and I couldn't find one that solves my problem. My ethernet connection was initially a public connection until I changed it to a working connection where it still does not work. I also tried to diagnose the "connect to the Local network' and it comes up with"Connecting to the Local network"doesn't have a valid IP configuration.

  IPconfig:

  No IP address is valid:

  Hello Alan,.

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  1. you made any hardware or software changes on your computer before the show?
  2. What is the brand and model of your computer?

  Thank you to provide detailed information on the issue and your efforts to resolve.

  This problem may occur because of corrupted or incorrect settings of Internet connection.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  IP address to renew and check. Please follow these steps:

  a. Click Start and type cmd in the start search box.
  b. right click on cmd , and then click run as administrator.
  c. type the following commands in the command prompt and press ENTER after each.

  ipconfig/release
  ipconfig / renew

  If this does not help, use method 2.

  Method 2:
  Reset TCP/IP and check.
  Refer to this article:
  How to reset TCP/IP using the NetShell utility
  http://Support2.Microsoft.com/kb/299357

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• my wireless network connection doesn't have a valid IP configuration

  Hello all I tried all the things after searching the Internet for hours trying to solve this problem.  my computer does not display the available wireless networks.  I tried to renew my IP with ipconfig and it did not work.  I have also reset IP/THC and flush the DNS.  This problem occurred when I tried to change the ip address of my router because it matched my modem so that I could change the security settings.  I was going back to my router ip 192.168.5.1 to correct what I did but I now can not connect to internet at all.  When I go to the command prompt and type ipconfig/all, I get media disconnected with active DHCP and autoconfiguration.  But I also noticed there is no IP listed for IPv4.  If anyone has any ideas on how to solve this problem, it would be greatly appreciated.

  Try to connect by Ethernet cable to your router.
  If this does not work either I suggest that you set your router to the factory settings and to reconfigure him.   I'm not sure what you did, but suspect he touched the routers DHCP service.  Most routers have a built-in reset that you press with a paper clip or similar button and hold for 10 seconds to reset.

• wireless network connection doesn't have a valid IP configuration

  tried to clean boot

  tried the ipconfig output

  netsh int reset

  tried to uninstall the driver

  nothing has worked

  Please help me

  Please download the app > run it > download the output to onedrive file or any other file sharing service http://1drv.ms/1FGQ0lU
  Please enter each of them in a command prompt high after you run the above and save the file

  ipconfig/flushdns

  ipconfig/registerdns

  ipconfig/release

  ipconfig / renew

  NETSH winsock reset catalog

  NETSH int ipv4 reset reset.log

  NETSH int ipv6 reset reset.log

  Output

• I can't print due to the "wireless network connection" doesn't have a valid IP address.

  Cannot print wireless

  I can't print due to the "wireless network connection" doesn't have a valid IP address.  How can I fix this problem myself (an absolute non-techie)?

  Hello

  -Did you change your computer, after which the question began?
  -Check if you are connected to the network?

  The question seems more like a network connection problem. I would like you to do the following.

  Method 1: run the Network Troubleshooter utility and see if the problem persists.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

   
  Method 2: release and renew the IP (Internet Protocol) address and see if the problem persists.

  has. click Start. Type cmd in the search box and press ENTER.
  b. at the command prompt, type the following command and press ENTER:
  ipconfig/all (there is a space between ipconfig and /)
  The command ipconfig/all command displays for all your network adapters, TCP/IP in Windows settings.
   
  If your IP address of your Local network connection is 0.0.0.0 or 169.x.x.x (where x is a number any), then your computer is not getting an IP address from the router.
  If this is the case, try this:
  ·        enough ipconfig at the command prompt and press ENTER
  ·        ipconfig / renew in the command prompt and press ENTER

  Method 3:

  Network printer problems

  Note: The steps also apply to Windows 7.

• My windows Vista, SP2 doesn't have windows fax and scan lilsted.

  Original title: windows fax and scan.

  My windows Vista, SP2 doesn't have windows fax and scan lilsted. I followed the suggestions of look in System 32. The required file IS NOT THERE! How dan I installed?  I need this program is not compatible Vista my my printer HP Compaq, so I can't use it to scan documents.   The named file was something with FS.exe (don't remember it all now, but he was not there.)  I see that others have found the same problem, with it is not there.

  Please notify.

  E-mail address is removed from the privacy *.

  I read somewhere since the announcement that this feature is not same inclued with Vista Home premium.

  That's OK, Windows Fax and Scan is included in the company and full editions: http://windows.microsoft.com/en-US/windows-vista/products/compare

  You will need to seek an alternative program to use.

• Pavilion e9150t: my local network connection do not have a valid IP configuration

  I lose the internet connection program to fix auto i run window, it will come out with area connection do not have a valid IP address

  configuation and no. fixed, please help me to solve this problem

  Hi again ke0757,

  This is fantastic news!

  If this answer solved your problem, can you please mark it as an accepted solution? This will help others with the same question to find the answer they're looking for.

  Have a great rest of your day!

• don't have a valid IP configuration

  Hello

  I can not myself connected in wifi for several week
  quandde met solve the problem ca answers me don't have any valid configuration
  I don't know what to do nor strictly knowing nothing
  Thank you for your answer
  Please select your language from the drop-down menu at the bottom of the page to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the desired language, support for additional international sites options are by following the link below:
  
  Please get your language in the drop to bottom of the page to post your questions in the language of your choice down. The forum you posted is fr English only. If you can't find the desired language, press the options of additional international destinations can be found by following the link below:
  

  http://support.Microsoft.com/common/international.aspx

• my wifi doesn't have access to the internet

  I have no problems before, but since I had the system ultimate internet phone I have more access to internet wifi. Any suggesstions.

  I called the company and spent several hours on the phone with them, I also have dumped story, disconnected from everything and plugged all back, no help.

  Hi MoWhite18,

  ·         What version of Windows is installed on your computer?

  ·         You receive an error message or error code?

  To fix your problem, try the following methods one by one.

   

  Method 1: Update the network driver.

  Steps to update of network driver:

  a. click the Start button.

  (b) in the search box, type devmgmt.msc , and then press enter.

  c. Select the peripheral network adapter and right click on it

  d. now, select Properties.

  e. in the Properties window, on the driver tab, click Update driver .

  f. after the installation of the updates, restart the computer.

  For more information, see the article mentioned below:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

   

  Method 2: Try resetting the TCP/IP stack.

  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

  If the same problem still persists, then try the next method.

  Method 3: Here you must troubleshoot using the resolution of network problems in Windows 7 and check for the issue to this follow the link provided below.

   

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Let us know if that helps.

• My Windows XP computer doesn't have internet access. I tried ipconfig and it shows default gateway.

  I have Windows XP Home... and all of a sudden I get no internet access.  When I do ipconfig... it does not show a default gateway.  I did everything update driver LAN, resetting the router, restart, by specifying the IP address (from the automatic ip configuration) and is still not available.  I know that the router is that I can access it from another computer.  any help would be greatly appreciated.

  original title: default gateway problem

  Is the connection wired or wireless?

  What version of XP, including service pack? (do right click my computer and select properties for info)

  It happened just before this problem occurred (failure, virus infection, etc.)?

  If this is a wired connection (which, I suppose, since you mention the 'LAN' pilot), have you tried to connect the Ethernet cable into a different socket on the router, (b) using an Ethernet cable from verified (maybe the computer that works), or (c) confirming that the Green LED next to the computer's Ethernet Jack lights up when the cable is connected?

  Given that you know about ipconfig, it would have helped if you had provided the results of the ipconfig command.  Here's a way to do it, but first configure the card to obtain an IP address automatically

  • Open a command prompt window
  • Type the following lines and press ENTER after each line

  ipconfig/all > "% userprofile%\Desktop\ipinfo.txt".
  Notepad '% userprofile%\Desktop\ipinfo.txt '.

  • Copy and paste the contents of the Notepad document in your response.  Close the command prompt window and the window of Notepad and remove ipinfo.txt from your desktop.

• How to make a Windows XP cd? I have a valid key.

  xp home edition CD to contravening office keys

  Thank GOD always

  How are you GOD bless you all

  have INSIGNIA desktop with windows XP Home edition Cliaa XP CD key needs install

  Thank you

  Hello

  Microsoft distributes not setup Windows XP disk more. Support for Windows XP has been completed. You may need to contact the computer manufacturer for additional assistance on the same.

• Windows 7 screen doesn't have a photo and then starts to blink. Can't get sys repair of work either!

  Step 1 - start the computer - everything seems fine, Windows starts very well and brings me to the login screen.

  PROBLEM: Login screen has nothing on it, but the pictures and the note of windows 7 on the bottom. If I have, in my frustration, to sit and watch for a few seconds the cursor shows busy and the screen starts flashing.

  To solve this I ran all sorts of diagnostics of the equipment screen you get when you press the F key it tells you to start - before it comes to the windows login. I spent a day run this.

  Today, I got online using this, my other computer, Googling the problem, I found that I can press F8 while trying to start and get the repair screen - which takes me for the most part to the windows screen that won't let me go anywhere!

  PROBLEM 2: I chose to launch repair and when I choose repair launch on the screen that allows me to do or to start windows normally it's just this page - no matter how I try to choose.

  So, I can't use the computer and I can't figure out how to repair the computer. I have a LOT of documents on this computer that I can't replace. Please, please, please help me!

  Hi Cheryl,

  Thanks for posting your query in Microsoft Community.

  Do you remember the number of the update?

  {For the KB updates of failure numbers, follow the underlying steps: }

  1. Open Windows Update by clicking on the Start button. In the search box, type Updateand then in the list of results, click Windows Update.
  2. In the left pane, click view update history. Check the recent update installed.}

  I understand that you found start flashing screen questions in your Windows 7 system. This scenario has started happening after installing the recent update of KB3097877.

  In order to diagnose and resolve the issue, I suggest you try the steps posted by Ravinath P replied on 13 November 2015 in the following thread and check if the steps help you to solve the problem.

  Screen flickering and problems log on Windows 7 after installation of updates

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-update/flickering-screen-and-sign-in-problems-on-Windows/df9c8255-587f-4DBF-BB45-6639b29dc4ae?TM=1447375680761

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.