With a Dell driver problems

Similar Questions

• Reference Dell T610 with 5 hard drive problem (5x2TB) while create RAID 5 with all the HARD drive. :(

  Dear Sir.

  While I have already configured the RAID 5 with 5 disks, then the OS (windows 2008 R2) installation step I saw 2 separate partitions. and can I install it on the partition with only 2 TB. Another, we can't. So during my installation completed OS, then I can use only 2 TB, for another volume is about 5 TB can't do anything. Can I do the RAID 5 with 5 disks (10 TB)?

  I wait your helpful to my set.

  Thank you.

  silamay

  This is new server, there is not any data yet so I can reinstall. What I want is that I just want to RAID 5 until I started my DC project. I already look for how to convert to GPT, but I'm not at all.  I know that I can't convert GPT as the OS in the same disk but that is because I try to configure RAID 5 and OS, but while over OS I do not see another 5 to just see only 2 TB.

  I don't understand most of what you wrote.  You must activate the UEFI (below), then convert to GPT before installing Windows.

  silamay

  How can I install on a UEFI system?

  The T610 supports UEFI, but must be allowed.  Start the BIOS (F2) Setup and change the boot mode in the UEFI instead of BIOS/inheritance.

  Your alternative is to create a RAID 5 using all disks, but the definition of the size as something as small as 2 to, then another RAID 5 with space remaining.  Each table will be displayed in Windows as a separate 'drive' - you can then install normally in the smallest 'drive '.

• Reader of SD with Tecra M2 driver problem

  Hello

  I formatted my laptop: TECRA M2 PTM20E-0R1LZ-FR / PM 735

  I found all my drivers for all execpt for the SD reader componet.

  It was very difficult to find the SD host controller, but I finally found it:
  Toshiba Secure Digital host controller
  oem17.INF:Toshiba:SDHost:6.0.4058.0:pci\ven_1179&d ev_0805

  But now, when I insert my SD card, I have a problem with the SD reader driver.

  So, if anyone has an idea...

  I did all the forum, all the driver toshiba support page and nothing on that kind of driver.

  Thanks for your help.
  Kind regards
  xVZx

  What type of problem do you have when you insert the SD card?
  Do you use drivers from the Toshiba support page?
  Do you use took in charge a card SD (support capacity)?

• Start with external hard drive problem

  I recently bought a Western Digital 1 TB external hard drive. When it is connected through the USB port my Pavilion a815n Windows XP hangs on the blue HP screen at startup. Western Digital technical support Advisor info sent to me I need to change a setting in BIOS but I can't find the trunk of USB device option setting in the BIOS of HP.  Can you tell me how to access this setting, or what else to do to solve the problem?  Thank you!  Jake

  Problem:
  After connecting a device USB to the PC, the computer does not start in Windows.

  Cause:
  The motherboard has a boot from the USB device, or a similar option, which is enabled in the system BIOS.

  Solution:
  In the system BIOS, disable the option to boot from the USB device and the USB Legacy Support option. This will allow the PC complete the process on the internal hard disk and allow you to enter Windows. If this does not work for any reason, you should boot your PC before connecting the USB key. Once the computer is fully booted Windows, plug the USB and wait for the operating system to detect the drive.

  Update the BIOS seems to have solve the problem. It was normally restarted with the attached hard drive.  Thank you!!  Jake

• Epson Stylus Photo RX420 with Vista printer driver problem

  I have an Epson Stylus Photo RX420 Series all in one printer, copier and fax machine which worked perfectly on my old Windows XP computer.

  Unfortunately this XP computer has failed recently so I've upgraded to a new PC running Vista.

  When I try to install the Vista printer recognizes the device and research initially drivers preloaded to find the printer driver.

  He says so I need to use Windows update to download the right driver which I allow then (which is consistent with the information available on the Epson site that says I need to use Windows Update to get the correct driver).

  Windows Update, then go online and find the pilot, but finally errors saying installation fail due to a timeout problem.

  I have no other problems with Windows Update install the patches, fixes, etc. They all have download and install correctly and they should be larger in size than the printer driver.

  Any thoughts on how I can get the correct driver for this printer, download and install?

  Hi IanRP,

  I suggest to download the compatible driver for your printer from the link below and check if the problem is resolved.

  http://eSupport.Epson-Europe.com/ProductHome.aspx?LNG=en-GB&data=nKGrQtfEm6nklAFAU002FI5XulUnXahGGzFymQyp3UZx8RYU003D&TC=6

  If this does not work, try to connect to the Windows Update site. To do this, visit the following Microsoft Web site and install all updates.
  http://windowsupdate.Microsoft.com/default.htm

  You can check the link below:
  Find and install printer drivers
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-and-install-printer-drivers

  Please post back and let us know if it helped to solve your problem.

  Kind regards
  KarthiK TP

• Satellite A60-712 with ati2dvag ATI driver problems

  Using the notebook after a short time the ati driver crashes setting the display resolution to 640 x 480 and the minimum color depth.

  This is the error code:
  BCCode: ea BCP1: 83E23C90 BCP2: 83E31008 BCP3: 83F65008
  BCP4: 00000001 OSVer: 5_1_2600 SP: 2_0 product: 768_1
  

  I try but I can't be able to solve it, an idea?

  Hello
  I think that there are only two choices for you.

  The first is to uninstall and reinstall the ATI Driver.If that does not work, try to restore your system with the CD or DVD delivered.

  If after this procedure the fault persists, contact the nearest Toshiba Service Station for control of your laptop.

  Good bye

• Satellite M60-164 with Major hard drive problems

  All started about 3 months ago. Whenever the computer is started, he would get a certain distance the BSOD do turn up and disappear immediately and the computer should restart. Yesterday, I discovered the F8 trick to make the stick BSOD around for quite some time. It turns out that the problem was an "Unmountable Boot Volume". I inserted my Windows CD and ran the repair center thingydingy and entered chkdsk/r. He said there seems to be unrecoverable problems on the hard drive.

  I bought the computer 2 years ago, and I think that I only have a 1 year warranty.

  What are my options?

  Thank you

  Luke

  Looks a bit like a HARD disk failure!
  Have you tried to reinstall the operating system on the HARD drive?
  Check if this is possible

  After the installation of the OS, you can try running a like for example the HDD Regenerator HDD repair tools.
  http://www.Gold-software.com/download7605.html

  If this does not check if the replacement of HARD drive helps you solve this problem!

• ENVY of HP dv7 - 7398ca: heat with two hard drives problem?

  I have a HP ENVY dv7 - 7398ca. The original hard drive crashed. I replaced it with a Kingston SS drive and plan to add a second drive slave 1 TB.

   

  My question is, the stock fan will be able to handle the heat of two hard disks.

   

  Thanks for any response.

  Hello

  Should be ok. The machine is designed to manage two HDD mechanical (or normal).

  Kind regards

• Printer with Windows 7 driver problems

  I have an Epson CX5500 printer. He has worked on a desktop computer, but does not work on my laptop that is running Windows 7. I have the original disc, but have also tried to download a printer driver on the Epson site. It downlaods very well, but Windows will not let me run - no explanation or suggestion given. The Windows Help Center was useless as usual. It seems that all versions of Windows multiplies the previous problems. I'm desperate. Any suggestions?

  I have an Epson CX5500 printer. He has worked on a desktop computer, but does not work on my laptop that is running Windows 7. I have the original disc, but have also tried to download a printer driver on the Epson site. It downlaods very well, but Windows will not let me run - no explanation or suggestion given. The Windows Help Center was useless as usual. It seems that all versions of Windows multiplies the previous problems. I'm desperate. Any suggestions?

  You say that you have downloaded a driver from the Epson site, but have you downloaded the * good * driver? You need a driver for the Epson CX5500 for * Windows 7 * and the correct 32-bit version or 64-bit Windows that you are running.

• Suddenly my laptop refuses to open the log in page and everything leads to blue screen of death, something to do with the hard drive problems.

  I do not quite understand computers.

  Randomly, I received a notice pop up saying that I need to backup my files because windows detected a hard disk problem.

  I did scans and system restore but nothing works.

  I used to be able to access safe mode, but now I do not get this option.

  I kept getting the blue screen of death to do something.

  But now I have nothing other than the loading page "TOSHIBA Leading Innovation".

  I have a Toshiba laptop, his more than two years and use Windows Vista.

  No miracle solution?

  Or should I bring to wait for him?

  If so where I will get the best service at afforable prices?

  Hi BethanyLa Chappelle,

  I suggest you perform the steps in troubleshooting from the following link and check how it works.

  What to do if Windows does not start correctly

  What are the system recovery options in Windows Vista?

• I reinstalled windows 7 in my dell with a hard drive recently changed. all these mistakes came after him: "windows has detected a problem with the generic bluetooth adapter," continues...

  "Bluetooth adapter", there is no driver installed for the SM Bus controller ' and "there is no installed driver for network controller" Please help!

  I downloaded all the drivers I could from dell.com and install, still nothing. Troubleshooting Microsoft, nothing.

  Hello

  Have you received an error code?

  Method 1:

  I suggest you run the Microsoft fixit tool and check.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 2:

  See the following links for more information:

  Bluetooth devices do not work correctly on a computer that is running Windows 7

  http://support.Microsoft.com/kb/980396

  Method 3:

  I suggest you to see the links and check.

  Add a Bluetooth device to your computer
  http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer

  Connect to Bluetooth and other wireless or network devices
  http://Windows.Microsoft.com/en-us/Windows7/connect-to-Bluetooth-and-other-wireless-or-network-devices

  Change settings for a Bluetooth compatible device
  http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-a-Bluetooth-enabled-device

  See also:

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

• Driver problem Dell R520

  I hope this is the right place. We have a server Dell R520 which was recently installed, win server 2008 r2. When I click on Device Manager, we perhaps 10-30 items in other devices. More listed as Base system device. There are also 8 other devices listed as Performance counters. We went through the Dell page fighter pilot for some of them, but with little luck. Also installed plenty of manage of dell, don't know if that helps. Also installed drivers for the deployment of an operating system from dell. Called dell support and advises him to restart the server and f10 in the lifecycle to install drivers from their deposit. I have not found anywhere in the life cycle of the to do. Anyone got any ideas how to get these drivers? Is their a way to get a r520 download Dell driver disk? Thanks for your help, Trevor

  Hello

  If you have installed the operating system from a Microsoft Retail version, you may need to apply the driver Chipset from Dell.

  See if this helps solve your problem and let us know how it goes.

  Recommended chipset Version 9.3.2.1015, F00, published on 04/10/13,

  http://downloads.Dell.com/FOLDER01757764M/3/Intel_C600_X79_Series_Chipset_F00_ZPE.exe

• "A problem with the display driver.

  Recently, I get an error message whenever I open Photoshop CS4. It reads as follows.

  "As Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

  "GPU improvements can be enabled in the Performance preferences panel."

  I checked the graphics cards in Device Manager, and when I tried to update the software, it told me that I was aware.

  • OS: Vista Edition Home Premium
  • Dell Inspiron 1520
  • Display driver: NVIDIA GeForce 8400 M GS

  Sincerely, Danny

  Hello

  Try to update your display manually driver and do not use the analysis of the drivers on the manufacturer's website either.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• Windows 7 problem with the Dell XPS 15 laptop (L502x)

  Dear friends,

  Greetings!

  I need your assistance related to a problem, I was confronted with my Dell XPS laptop computer L502x purchased in the United Kingdom a couple of years back. In fact, I tried to update my system for windows-10 de-windows 7 Home Premium (originally installed) via windows update. Later, due to some display problems driver I had to return to the former. But, as soon as I returned my windows for windows 7 HP, it stopped at day no more and I was constantly receives the message from windows update that always ends with a constant error message; so the update process has failed every time.

  Therefore, I want to restore my laptop to factory through the restore partition settings that already exist in my machine, the "repair" option does not appear (snapshot attached) when I hit the F8 key. I wonder if there is another option available to use this recovery partition to recover my laptop to factory State. Please suggest me the solution so that I can do what is necessary to restore my machine to the factory settings.

  I can't wait to have an encouraging response from you.

  Best,

  Adnan!

  If the Ctrl key pressed, while pressing the F11 key repeatedly (about once per second) at startup does not work, it means that the recovery partition no longer exists.  If this is the case, you cannot restore to the factory.

  This would also be the case if the hard drive has been replaced.

• Dell Inspiron 15R SE AMD video driver problems (7520)

  Hello

  Updated Windows Installer update drivers AMD GPU for me earlier. I think the problem is that it has installed the AMD site instead of graphics drivers switchable drivers that are compatible with my laptop (Inspiron 15R SE).

  All programs that use the AMD card crashes when I start the system, including the Catalyst Control Center and the switchable graphics program. I tried to get into windows to display advanced options, but windows stops responding when I open the menu (Gray screen for about a minute then it returns with the window closed).

  Dxdiag crashes if I start it, and if I try to run again he asks me if I want to run without Direct3D. If I press 'No', it crashes. If I accept, he let me in but does not detect the graphics card AMD.

  I tried to uninstall the drivers and re - download coupons Dell website, but the problem persists.

  I'm running an AMD Radeon HD m 7730 GPU and 4000 HD Intel integrated graphics.

  TL; DR: All programs set to use graphic crash dedicated. Drivers say they have updated, but the problem is still there. Cannot access driver rollback screen (windows crash).

  If you need more information, just ask. I run the Dell Diagnostics tool and he found nothing wrong, so it is a driver problem.

  Hello

  I followed the steps you posted. Uninstall driver AMD asked me to restart later, so I allowed him to. I was greeted with a BSOD whenever I started. I tried to boot my Dell driver recovery disk, but there is no drive detected. I finally decided I had to do a system restore.

  The good news is that the problem is resolved.

  Bad news is that I lost all my files. This time I am disabling the windows driver updates...