WLC integration with ISE

Similar Questions

• Guest access with ISE and WLC LWA

  Hi guys,.

  Our company try to implement access as guest with dan ISE WLC with the local Web authentication method. But there is problem that comes with the certificate. This is the scenario:

  1. the clients are trying to connect wifi with guest SSID

  2. once it connects, you can open the browser and try to open a Web page (example: cisco.com)

  3, because guests didn't connect, so this link redirect to "ISE Guest Login Page" (become): url

  https://ISE-hostname:8443/guestportal/login.action?switch_url= https://1.1.1.1/login.html&wlan=Guest&redirect=www.cisco.com/

  )

  4. If there is no Login to ISE not installed comments Page, no reliable connection of message message, but it will be fine is they "Add Exception and install the certificate".

  

  5. once the Guest Login Page will appear and you can enter their username and password.

  

  6 connection success and they will be redirected to www.cisco.com and there pop-up 1.1.1.1 (IP of the Virtual Interface WLC) with the logout button.

  The problem occur in scenario 6, after the success of the opening session, the Web page with the address and the error of certificate ISE IP to 1.1.1.1 is appear.

  

  I know that it happened when you can has no Page of Login of WLC certificate...

  My Question is, is there a way of tunneling WLC certificate to EHT? Or what we can do for ISE validate certificate WLC, invited didn't need to install the certificate WLC / root certificate before you connect to the Wifi?

  THX 4 your answer and sorry for my bad English...

  Do not mix WLC with ISE comments Portal local Web authentication. Choose one or the other. I suggest the portal + WLC CWA.

• Passwords enable ISE device Administration (ACS) integrating with Active Directory

  I'm working on a standalone application ISE and running into a problem where the password to enable for a device is not shoot properly.  I have the original connection related AD and I policy conditions/results/sets all as they should be working.  My test run is a 2960 S.  I tried to set up ' group aaa authentication enable default Activate ', but the only way I could do a login enabled with which was if the user has configured locally in ISE identity management > identity > users.  Is there something that I missed that tie will enable passwords for a group active directory as I work for the initial logon?

  I see just a mistake with your failure to enable aaa authentication enable. You must specify the Group of Ganymede.

  Right now, I don't have access to my lab with ISE.

  Here's my config for switches used with ACS.

  AAA authentication login GANYMEDE-SRV Group Ganymede + local
  local authentication AAA Console connection
  Group AAA dot1x default authentication RADIUS
  AAA authorization exec GANYMEDE-SRV Group Ganymede + local
  AAA authorization commands 15 GANYMEDE-SRV Group Ganymede + local
  Group AAA authorization network default RADIUS
  AAA accounting exec GANYMEDE-SRV arrhythmic group Ganymede +.
  orders accounting AAA 15 GANYMEDE-SRV arrhythmic group Ganymede +.

  If you give me all out maybe we can understand why your GANYMEDE ISE works do not with the AD. I see no reason except a misconfiguration or another issue.

  Just to go to the mode, you need more aaa authentication command activate by default enable. This activation mode is pushed to the user if he gets the privilege 15. Your problem should be on the profile or politics. With the approval journal, we can see whether or not ISE pushes politics and why?

• Integration with 50G

  Hello!

  Well, when I tried to compute the definite integral of | Sin x | I received the message cannot find the signin [0, 2 ft].

  

  I went in RPN mode, and this error persists. I then used [RS] [ENTER] to get the numeric result, and after awhile, I got the correct answer 4. But I can't get the answer simplely by clicking [EVAL].

  I also tried to calculate the antiderivative, and the correct answer returned Calculator -cos (x) * sign (sin (x)). I was wondering why the calculator produces an error when they apply for an accurate result (not digital, without .).

  Jack

  confirming the latest set of equations:

  

  EVAL would be = - 1

  and -> limit X PI - 0 = 1

  and the limit X-> PI = cannot determine.

  So, there's a singularity...

  Unfortunately, because of the resolution of the screen of 50 G, when the resulting equation for the indefinite integral is drawn, clear breaks in the plot IP and 2 * PI are not 100% clear.

  However, the subsequent calculations confirm that they exist.

  This is what has been shown that when the original integral from 0 to 2PI of | Sin (x) | is calculated,

  It is clear that the 50G automatically sets ON RIGOUREUX, even if it is not enabled in the (likely due to the function absolute value in the equation) indicators.

  THE rigorous is perfectly reasonably expect when the EXACT mode is selected with a function of absolute value.

  now for a pencil and paper method:

  | Sin (x) | is sin(x) from 0 to PI

  | Sin (x) | is - sin (x) IP to 2PI

  so...

  integral from 0 to 2PI of | Sin (x) | can also be expressed in

  integral from 0 to PI of Sin (x)

  +

  integral of the AP to 2PI of-sin (x)

  

  in EXACT MODE (strict mode setting is more questions)

  When EVAL would be = 4.

  I can refer you to a message done previously by Bernard Parisse (one of the developers of CASE).   Bernard said that the CASE cannot intercept all EXACT integration singularities (but it report some).

  Regarding the digital approximation method (help-> NUM) to get the result... I can't offer no answer as to the reason that the singularity is resolved.

  I've never seen a single post indicating what type of digital approximation algorithms are used for approximate integration with the 50G.  Of course, the digital approximation algorithms are distinguished by exact calculations.

  Finally, FYI, here is another good example of the use of 50G with an integral and having to use a bit of paper and pencil methodology (in this case, the method of cauchy principal value) to solve the 50G of the singularity.

  /T5/calculators/50g-numerical-integration-with-singularities/m-p/5678169#M11440

• Is there a work around to show the Site identity button when the integration with facebook like/send etc. It disappears when it comes to the page, it's because of the iframe can be done if anything.

  Is there a work around to show the Site identity button when the integration with facebook like/send etc. It disappears when it comes to the page, it's because of the iframe

  What can be done if anything.

  Pages that use "mixed content" (parts of the use of the HTTP page and some use HTTPS) are not secure against tampering, they will not display the site identity button. To resolve this problem, make sure that external resources you are incorporation are available over HTTPS and you use HTTPS to nest them.

  For example, to iframe widgets like the Facebook 'Like' buttons, make sure that your iframe use src = "https://192.168.1.20 /...". »

  See also discussion here: http://stackoverflow.com/questions/3587021/facebook-like-button-breaks-https-ssl

• CRM integrated with MS Project Management

  Hi Expert,

  On the CRM integrated with MS Project Management, there any company always do this?

  In fact, there are only certain configurations or it's really complicated customization?

  The result of the integration is really effective and efficient?

  Can share with me the practice of MS Project to the planning of resources management?

  Thank you!

  Hello

  The question you posted would be bettersuited in the TechNet Forums. I would recommend posting your query in the TechNetForums for more assistance:

  http://social.technet.Microsoft.com/forums/da-DK/projectserver2010general/threads

• While freeing up disk space, I accidentally deleted MSOffice, which is integrated with my HP 1000

  While freeing up disk space, I accidentally deleted MS Office which is integrated with my laptop HP 1000. How to restore my MS Office 2010 Starter? HP predict that if the product is still in warranty period?

  I tried restoring the setting factory but without any real help. Please help me!

  Kind regards

  Ron

  Once Office Starter is removed there is no way to reinstall. Even make a system back to factory settings recovery will not reinstall it.

• Cisco WLC 2504 with AIR-AP1131AG-A-K9

  Hello

  Can you help me for some info about AIR-AP1131AG-A-K9.

  I have a wlc 2504, but I don't know if the AIR-AP1131AG-A-K9-supported 2504 wlc.

  Can work this WLC 2504 with AIR-AP1131AG-A-K9 solution?

  If so, guide.

  Thank you very much

  Gezimv

  Check out this link. As long as you have software version 8.0.x 2504 version you can use 1131 AP with it. Nothing beyond software fate is more a series of support 1131.

  http://www.Cisco.com/c/en/us/TD/docs/wireless/compatibility/matrix/compatibility-matrix.html#56735

  HTH

  Rasika

  Pls note all useful responses *.

• ASA 5525 X Anyconnect configuration with ISE 2.1

  I have a new deployment of ISE 2.1 which is used only for the management of the devices at the moment.  The intention is that it will serve as radius for authentication of our VPN server.

  5525 x is a brand new ASA runs the 9.4 code.  I want to configure VPN on the SAA strategy so that each user is assigned a DAP based on their Department.

  I already have the designation of the Department for user accounts assigned in AD through a group membership.  I don't know how to get ISE to belonging to a group at the ASA so that she can associate the user based on this correct in RAP group membership.

  I succumbed to determine how this is supposed to work.  Thanks for any help.

  @Jonathan Harrison ,

  Normally we authenticate and authorize users and then push DACL or allow connection from ISE etc. of such conditions profiles that check results Posture or parts constituting the identity of the user (such as AD or another external identity store belonging to a group).

  There are a couple of good guides to do so, including detailed examples:

  https://communities.Cisco.com/docs/doc-68158

  http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-app...

  http://www.Cisco.com/c/en/us/support/docs/security/AnyConnect-secure-mob...

  While they focus on the case of use of Posture, they can be adapted to add other uses. For example, ISE registration condition may be the result of not only a Posture check also membership in a given group or another if you make it a State.

  I do not think we can specify to the ASA to call a given font of DAP like Hostscan module cannot be used at the same time that the module ISE Posture. However, you should be able to accomplish just about everything you used to depend on the DAP with ISE Posture Module AnyConnect (assuming you have AnyConnect 4.x Apex licenses).

  If you want to stick with the ASA DAP model, you can forgo using policies and module ISE Posture and instead create an authorization profile (result) to send the ASA, a pair of RAY - V based on a correspondence (in the authorization of the ISE policy) with the ad group. He is a "Cisco-VPN-3000" A - V called "PIX7x-members-from' that can be used in ASA dynamic access policies. You can see (and all other pairs A - v supported buy ISE) here:

  https://communities.Cisco.com/docs/doc-67894

• WLC 2504 with AP 1121 g

  Hey there,

  I have a problem, maybe you can help me.

  I want to join the FOLD of the AIR-AP1121G-E-K9 to a WLC 2504 with software version 7.4.x.

  In the compatibility matrix, I saw that it is only possible if the WLC has 7.0.x software version.

  So my questions are:

  1. Why is it needable to upgrade the 7.0.x to 7.4.x WLC?

  2. is it possible to join the AP1121G a WLC 2504 with 7.4.x version?

  3. What is the difference between version 7.0.x and 7.4.x

  I hope you can help me

  Yes.  That is right.  You need to downgrade the firmware of your WLC to 7.0.X to allow the APs 1100.

  Make sure that you back up your configuration before the downgrading of your firmware.

• SX 20 integration with VCS

  Hello

  Is it possible to integrate 20 SX with VCS.

  Because our customer want to integrate with their MS Lync TP, so found that VCS can do this job. Then please suggest...

  Here also to point out that we are planing to use the public IP address for SX 20 to receive incoming calls from the public IP address, as it will be integrated with ISDN gateway.

  Details of the product for this solution:

  VCS

  SX 20

  TP ISDN Gateway

  Thanks in advance...

  Kind regards

  Daniele

  Yes, its possible, check this.

• Replacement of 6000 MXP Integrator with unique display. C40 SX20 vs?

  I have to make a quick decision and my CISCO sales representative is MIA :(

  We have a bunch of 6000 s MXP (package ingegrator), I would like to replace. They are simple installations with a single monitor on a roll integer grid.

  with output to the screen and a camera is there any point to spend the extra money for a C40 vs getting a SX20? From a point of view video capability they look pretty well. C40 more things gets me in the back, but it is a pretty simple setup.

  Just looking for what people here could do?

  Thank you!

  Although C40 and SX20 are two different solutions for videoconferencing from Cisco, an integrator (c40) and other is fast setting solution (SX20).

  The SX20 Quick Set is designed to provide multi-party and Conference video to high definition with the flexibility to adapt to various configurations - all at a value price and size of the room.

  C40 is for Integrator supports for integration with 3 party like crestron devices, mixers.

  two take in charge the premium 1080 p solution.

  both are excellent solutions and are mind blowing in the feature and the feature as compare to the MXP series.

  You can't go wrong with either.

• Cannot open the URL of the CWA with ISE

  Hi people,

  I have a problem when you perform the CWA with ISE so that I can give you access to the network for the guests.

  Everything is fine except the URL of the CWA: when guests, open Explorer and enter a domain name after you have connected the SSID, they will be redirected to the URL like 'https://hostname.demo.com:8443 / guestportal /... ". " which begins with the hostname of the ISE and the domain name of the ISE, but for us, we have not any announcement and the LAN DNS for our network so that we cannot translate the hostname.demo.com in the IP address of the ISE, so can I just change the URL type of intellectual property like"https://10.10.10.70:8443 / guestportal?

  Screenshot of an attached screenshot (sorry).

  Basically it's in the authorization policy, allows you to use a static DNS or IP address

  

• Integration with the PIX IDS firewall

  I read the Release Notes for Cisco Intrusion Detection System Sensor Version 3.0 S4 (1), and tripped on the new features of this version it pretends the integration with the PIX firewall

  How do implement you this? What kind of integration offer?

  Instructions for the sensor and the basic configuration of PIX can be found here:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids8/13870_01.htm#xtocid23

  Instructions for sensor and PIX SSH configuration can be found here:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids8/13870_01.htm#xtocid16

  You can configure the sensor to connect to the PIX via telnet when

  using the PIX inside interface, otherwise you have to use SSH.

  SSH with 3des encryption is supported in version 3.0 or later

  sensors for connections of PIX.

  Warning: If you use telnet with a version 6.2.1 or PIX more late or if

  you want to use SSH with encryption on any PIX, so you

  need a patch for your sensor. If so, open a case of TAC and demand

  the latest version of nr.managed engineering. Reference

  [email protected] / * / for any question.

• ACS integration with Microsoft Active Directory Services

  Hi all

  I was responsible for developing the integration of GBA with MS AD. What I want to know is below assuming I have a software ACS or ACS device and the authentication protocol's RADIUS

  -What is the criterion of the announcement to integrate with ACS to device software

  -Should that AD hosted on the domain controller or not?

  -Otherwise, on what (DC, tree, forest, branch, flower, Fruit) the announcement must be hosted on?

  -What should I do to authenticate users logging into Cisco ACS Security Manager integrated with AD?

  -Are there other dependencies that I'll have to speak categorically in my description?

  Thank you

  Rishi

  First of all, I love the flower fruit one keep it up.

  If ACS is for windows, it can be installed on the domain controller or member server. For detailed information about installation tasks post must have full integration, please see the following link that contains fancy things you are looking for:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/Windows/postin.html#wp1041202

  If ACS is soultion engine then you need piece of software called remote agent to be installed either on the domain controller or member server, also check the following link for more details on how to integrate it with AD:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.2/installation/guide/remote_agent/Rawi.html

  I hope this was informative for you.

  -----------------------------------------------------------------------------

  Please ensure good answers to rate