WRT160N v3 and the wii

Similar Questions

• New computer Windows 7 and the Wii

  Well, I really have no where else to turn, so I thought I might as well try these forums.

  Basically, my problem is that my new computer Windows 7 Home (I just bought 1 week ago), may not share the router with Wii my brother. This is the router card, as well as my problem:

  Linksys BEFSR41 V4, 4 port wired router-last update

  ISP is Comcast

  Configured for the port before the Wii, using the - Ports 1-65535, both TCP and UDP and assigned a static IP address 192.168.1.111 (which was at the recommendation of Nintendo on the phone)

  Wii has been assigned a static IP (as mentioned above) as it was my computer.

  Wii has the correct entries in the router DNS server

  Wii is configured to use the wired connection

  My computer is a Dell Studio XPS 8000

  Here's my IPconfig/all

  Microsoft Windows [Version 6.1.7600]
  Copyright (c) 2009 Microsoft Corporation.  All rights reserved.

  C:\Users\Mokey>ipconfig/all

  Windows IP configuration

  Name of the host...: Mokey-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  ... Description: Broadcom NetLink (TM) gigabit Ethernet
  Physical address.... : 00-25-64-E8-CE-10
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::45d:fd19:80fe:3 b 74% 14 (Preferred)
  IPv4 address: 192.168.1.150 (Preferred)
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 192.168.1.1.
  DHCPv6 IOOKING...: 251667812
  DHCPv6 DUID customer...: 00-01-00-01-12-B1-5C-31-00-25-64-E8-CE-10

  DNS servers...: 192.168.1.1.
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 12:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {677AB390-DC0F-4548-8F15-A546757783EC}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Adapter Microsoft ISATAP #3
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  My static IP PC specs:

  Internet Version 4 Protocol

  IP address: 192.168.1.150

  Subnet mask: 255.255.255.0

  Default gateway: 192.168.1.1

  Preferred DNS server: 192.168.1.1

  Alternate DNS server: white

  We have 2 computers and a Wii connected to the router, everything has a static Ip address. If Wii Port Forwarding is disabled, both, we can go online, no problem what - if - ever, everything is wonderful and quick. If the Wii is enabled on the router, my brother PC and Wii can apply online, but my PC can't. It has never happened before with my old XP sp3 computer (HP Pavilion, record quite high for the time, 9 years old, worked as a beauty ), but for some reason my other cannot share the line with the Wii. Just mine, no less . I don't know what could be the cause of the problem. I did research all this information when we first have his Wii, so everything was peachy until this new computer.

  Please, any help is very appreciated, I traveled more than 4 hours time to mobile phone, only to get the evasive of Comcast and Dell.

  Your TM602G is a cable modem which should work fine when your BEFSR41 resetting to the factory default values.  Note that your modem has a battery in it.  The battery must be removed, for a minute, each time that install you the modem with a new router, or connect a computer directly to it.  I suspect that is the reason why you couldn't get an Internet connection with the last configuration that we tried.  Also, do not connect anything to the TM602G USB port.

  For the time being, until all computers are running, please unplug the Wii.

  For now, please set both your computers in order to "Obtain an IP address automatically" and "obtain a DNS server address automatically".  Restart the computer and make sure it is always set up this way.

  I think it will be better to start with a "clean slate" to set up your network, the next step will be to reset your factory default BEFSR41.

  To reset your router by default, follow these steps:

  (1) turn off all computers, the router and the modem and disconnect from the wall.
  (2) disconnect all the wires of the router.
  (3) turn on the router and let it start up completely (1-2 minutes).
  (4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
  (5) turn the router.
  (6) to connect to a computer (if possible, use a computer Win XP or Vista) cable to port 1 of the router (NOT to the internet port).
  (7) turn on the router and let it start up completely (1-2 minutes).
  (8) the power of the computer (if the computer has a wireless card, make sure it's off).
  (9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
  (10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Let the empty user name (Note: some Linksys routers have a username "admin") and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen). Exit your browser.

  If you get this far without problems, put your entire network.  Then, using an ethernet cable, connect the ethernet on the TM602G port to port Internet (WAN) of the BEFSR41.  Leave your computer connected to the LAN of the BEFSR41 port.   Remove the battery from your TM602G and wait a minute.  Replace the battery in the TM602G.  Turn on your TM602G and let it start up completely (1-3 minutes).  Turn on your BEFSR41 and let it start up completely (1-2 minutes).  Turn on your computer.  Now, try to connect to the Internet.  If you have trouble, temporarily disable your firewall software computer and try again.  If you get a computer to get an Internet connection is working properly, then (using an ethernet cable) connect your second computer to the BEFSR41 and try to get an Internet connection active.    STOP HERE and the report with your results, including the results of step 9 and 10, and whether or not, both of your computers working Internet connections become.

  If you can not ' response to... ". "in step 9 above, your router is probably dead. A report with this problem

  If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. Related to this issue.

• Try to stream video to the Wii by using third-party software.

  original title: try to stream videos through thrid party

  XP pro SP3 with avg free and windows firewall and netgear router running.  PC is connected to the router; Wii's wireless

  I'm looking to stream video to my wii with the help of a third-party application that uses the pc as a server.  The application cannot access the pc and I spent the last two days to work with their support, trying to nail down the reason.  None of the newspapers I can access the port list or program in question being blocked and when I use the pc browser to go to the same place that the wii is trying to reach its done appear the application correctly.

  You try to use PlayOn.TV?  Have you checked their FAQ?  http://www.Playon.TV/FAQ#security

  If you can't make it work, people better ask are people in the PlayOn forum: http://www.playon.tv/forum

• Connect WRT160N wireless to the BEFSR41 wired

  Hello-

  I use the router BEFSR41 which is connected to my comcast modem and all PC, printer, computers cell phones work perfectly when you use additional ports.

  I want to know if its possible to add a wireless router, WRT160N, across to the top, so I can move and then another room with the laptop.

  I play internet games on my desk and do not want to move to the wireless, but use the laptop to other purposes of internet and sometimes need to use it in another room.

  I have read the posts here and it seems possible, I want to just make sure I get the correct connections. I have also read the messages that State no, do not.

  Are there easy instructions?

  Thanks for any help,

  CAT

  I think that from the beginning that my problem was trying to connect wireless to my desktop PC... and after an hour or so trying to reconfigure the son discovered is not wireless because at the end of the year I had to buy a new network card and wasn't capable wireless.

  I thought that since my office was the main link everything had to go through to the 'House' to work wireless connection.

  So the first time that I have not found a link on the desktop, we wire the PLACE directly to the computer laptop and charge the WRT software on the laptop. The problem, he had us were always wired to the router BE and this is the page of the Linksys who returned to the top. We try to change the LAN IP address and turned off DHCP, but of course when I am connected to the internet on the desktop, it was not to find the router.

  Of course during all this time, I was looking at this site and then went on the Comcast site, it just clicked and after several configurations more lead changes and trying to think about what I wanted to accomplish exactly, and how it "should" work... just went ahead as it was already set up and connected wireless to the BE and he was there.

  I also remember that when you reset the modem and the router... it takes 'time '. As at least 5 min, what seemed like 15 minutes at the same time, I tried all of this. My frustration level has not helped knowing that it "can" be done if I just follow the signs.

  So overall, my error when trying to set up my office as the main connection for the wireless and don't listen to not when my granddaughter told me that she 'had' upcoming wireless on the laptop.

  Thanks for your help and great advice. We have the wireless connected and followed your instructions on securing the router with the network name, encryption WPA2 and AES... and hope never to lose the piece of paper its written on.

• Wireless router WRT160N cable on the desk, I loose internet when the laptop is turned off.

  I have wrt160n v2 router wireless, it does not work for me.

  If my wireless XP laptop is only powered ON the Vista desktop internet wired connection works, I'm not wired or wireless using laptop computer, not on the internet, only power.

  If the laptop is turned off, I have no internet on the desktop, always connected via the router.

  The laptop is used and I didn't know if the without built-in thread was pretty new, so I bought a card to go in wireless.

  When everything is on everything is to play on the internet times two computers, but if you turn off the laptop I have to connect internet directly on the Office to continue in the internet.

  I started working with a tech support yesterday and they are difficult to understand. I had put in the new firmware and the problems persist.

  Can someone help me, I don't really have time to be on the phone for hours figure this all out.

  Thank you

  Jackie

  go to http://audipages.com/router/ and follow the instructions

• WRT160N V2 to the Modem connection cable

  I just installed a WRT160N v2 via the installation disc accompanying and everything came and worked fine for 3 days. After that, the response time seems to slow down, and later, my access has become more limited. I could access some websites but not others, and sometimes I could not access the internet at all, even through my wired connection. The router does not have the thought, I returned it for another and ran into exactly the same problem after that, even once, ran flawlessly for 3 days. I followed the instructions on the web site: cloned PC address, manually the value of the MTU, turned down the security settings of the browser to low to nothing does not. I have since disabled the security on the router, McAfee disabled on my PC, I have reset the router, reset the parameters of what the manufacturer came and have unplugged the router and my cable modem so many times my fingers are sore. I even tried to uninstall the software of the router to my PC and tried to set up manually, all without success. Any ideas out there?

  Hmmm that's weird on both routers you are faced with the same problem. I suggest that you connect your modem to the computer and follow the link for somedays. I think it must also be the problem with your modem.

• Difference WRT160N-EU and WRT160-EW

  Please explain what the difference is between these two wireless routers

  WRT160N-EU and WRT160N-EW

  Thank you, Andre

  The main difference is between the units firmware.  United States against Europe.  For example, the United States has 11 channels wireless and European 13 channels.  Make sure you order the correct version for your country.

• Unknown device on network adapter between the laptop and the wireless router

  I am running windows 7 64 bit on a laptop computer connected wireless to the router and internet.  The router is Linksys WRT160N connected to the internet.  The map of the network, there is a question mark device unknown between the laptop and the router.  However, I still have access to the internet.  In terms of network, if I hover over the laptop, it does not show an IP address.  It only shows the name of the computer and its MAC address.  Any help would be appreciated.

  Solved my problem.  I checked the button of the IPv6 protocol in the properties of a network connection on the laptop, and now I can see it's the IP address and the unknown device has been replaced by a switch and hub which is part of the router.   I do not uncheck the button IPV4.  I'm guessing that it is a bug in Windows 7 that you need to cut of ipV6 Protocol when you have a Win XP computer on the network if you want to see a map of own network.  As I said before, everything worked before, so this seems to be a cosmetic fix only.  I see that my shared files on the XP computer appear faster after a reboot.

• Pedometer in health app inaccurate since ios10.02 update and followed by the month and the year disappeared. Why?

  I used the pedometer in the application of health that accompanies the iPhone6 for 18 months. I walk on a treadmill each morning for the same distance and time. The number of step was close enough for more than a year, but then I updated to ios10.02 and the count has been reduced by more than 2500 steps every day for the same duration of time and distance on the treadmill. He remained much lower now for two weeks. I also notice that the dashboard no longer offers a total annual and medium, or monthly. Is there a fix to come or was the unit off so much for the previous year?

  kjm2222 wrote:

  I also notice that the dashboard no longer offers a total annual and medium, or monthly.

  You can still access graphics monthly and annual. In the form of health data, press activity. Swipe to today. Tap measures. You will then see a graph and a bar with options to choose to see it in days, months, or year. This works with any metric system.

• Problem starting el capitan (sierra) - built-in keyboard and the mouse do not respond

  Hello

  I have a 2015 macbook pro (SSD 256, 16 GB of RAM last el capitan updated) with a wired problem.

  I use it mainly to a cinema monitor and I use wireless keyboard and mouse (office installation program), and of course as a stand-alone laptop when I'm not at my desk.

  When I put the laptop to sleep, everything works fine when I wake up.

  but, if I'm away from the office and I have to restart my laptop, here is the problem.

  The boot process is very very slow, there is no edge, and when I finally have the screen to unlock the safe, the keyboard and the touchpad do not react. Actually, that's not exactly true, they are so slow that they are unusable and get caught quickly, all gel. So I can't unlock and complete the boot. My laptop is unusable ;-(

  At this point, I get a message that if I forgot my password I just need to reboot by pressing the power button, and I'll be able to reset it.

  When I do this and aprΦs the dΘmarrage that more slowly than usual but ok, I get another screen with several options of problem solving. One of them is "keyboard not responding do not. When choosing this one, it asks if you want to remove safe. I tried and everything was back to normal.

  later, I delivered safe and I had the same problem again. I did the thing to be able to restart again and improved to sierra in the hope that it would disappear. However, the problem is still there.

  I thought I could try to restart my office to see if my keyboard and wireless mouse would still work. Indeed, even if responsiveness was not normal, I could unlock and fill the chest.

  I have the impression that my laptop always "believe" it is on my desk, linked to my screen (probably the reason why I don't hear the Bell) and to my wireless K & M.

  It's really annoying and I hope someone has a solution.

  Thank you very much

  best,

  Alex

  I'm having a similar problem with macOS Sierra which I didn't have with El Capitan.  I can possibly move the cursor on the power button and turn off (no), but I must be patient because the keyboard and trackpad are only for a fraction of a second, which only allows me to move the mouse slightly.  After he stop and start back up, everything is perfect until I tried another reboot, and then I'm back to the beginning.

  I tried to reinstall the operating system, reset the SMC, resetting the NVRAM, reboot in SafeMode... nothing worked so far.

• Cannot restart or refresh my iPhone 7 from the "home" button and the sleep/wake button at the same time

  I'm having difficulty trying to restart and update my iPhone 7 using the Home button and the sleep/wake button at the same time, when I do my phone takes a screenshot of the home screen.

  Should I turn off my Touch ID?

  Basically my home button button and / standby works not together at the same time.

  You need hold the House and turn off the button for 20 seconds, until the Apple logo appears.

• The keyboard and the mouse no longer works to update you Sierra

  Hello, I upgraded to OS Sierra and I began to spend more and suspending Notepad, then I do not recognize their keyboard and mouse notbook. It forces the walk outside and then worked, but after a few days I don't work any more.

  Thank you

  The keyboard and the mouse no longer works to update you Sierra

  Hi gnardone,

  Thanks for posting in the Community Support from Apple. I understand that you are having problems using your mouse and your keyboard after the update for Sierra. View the work of keyboard and mouse are crucial for your Mac, so I can understand how this is a problem for you. I'm happy to offer assistance.

  You are having problems with the keyboard and the trackpad that are part of your MacBook or you are having problems with a keyboard and an external mouse? I recommend taking a look at the article below.

  If your Apple wireless mouse, keyboard or trackpad doesn't work as expected

  If you're still having trouble, let us know what kind of mouse and keyboard that you are having problems with and what you have tried to solve this problem.

  Best regards.

• 13-inch early 2011 macbook pro. light green mag extremely shoddy security cordon, macbook pro stopped charging bought new magsafe. and the led does not illuminate or strings. SMC reset now mac does not recognize battery. unplugged

  13-inch early 2011 macbook pro. light green mag extremely shoddy security cordon, macbook pro stopped charging bought new magsafe. and the led does not illuminate or strings. SMC reset now mac does not recognize battery. disconnected the battery and security cordon mag, maintained hold button / stop for 5 seconds, nothing. Another SMC reset and it is the only way Mac powered on that she has no back light for the keyboard and the fan works on high all the time, please can someone HELP, thanks.

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• iTunes and the App Store will not loading after update iOS

  I downloaded iOS 10.0.2 on my iPad Air. Now, neither iTunes nor the AppStore will connect. All the settings are correct and my internet connection is strong. What should I do?

  Hello. The time zone and the region are compatible with your actual location? If you've restarted since the update? Home amd Hold sleep until you see the Apple.

• I have someone just showed about 100 pictures of my iPad. Now, the pictures are missing, and the "recently deleted" folder is also empty. What can I do?

  I have someone just showed about 100 pictures of my iPad. Now, the pictures are missing, and the "recently deleted" folder is also empty. What can I do?

  Have you done something after their show.