WRT54GH dyndns problem

Similar Questions

• IPSec VPN with DynDNS host problems after change of address

  Hi guys,.

  I have a weird problem on an IOS router.

  I need to implement IPSec VPN L2L.

  Because of the security requirements of each site needed a clean pre-shared key. Sites dynamic IP and it's

  why I use dyndns.

  ISAKMP crypto key KEY hostname XXXXXXXXXXX.dyndns.org

  CMAP_1 1 ipsec-isakmp crypto map
  define peer dynamic XXXXXXXXX.dyndns.org

  First of all, it works fine, but after the change of IP address it no longer works.

  Debugging, I discovered that it resolves the new IP address but IPSec attempts to connect to the previous INVESTIGATION period.

  I tried this on two other IOS, 15.0 and 12.4

  This debugging output:

  01:02:39.735 Mar 1: IPSEC: addr of Peer Link70 (70.1.1.3) is out of date, triggering DNS
  * 01:02:39.735 Mar 1: IPSEC: Peer has the address 70.1.1.3 (DNS cache).                 New IP address
  * 1 Mar 01:02:41.731: IPSEC (sa_request):,.
  (Eng. msg key.) Local OUTGOING = 1.1.1.2, distance = 70.1.1.200, OLD IP
  local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
  remote_proxy = 10.254.70.0/255.255.255.0/0/0 (type = 4),
  Protocol = ESP, transform = esp-3des esp-sha-hmac (Tunnel),
  lifedur = 240 s and KB 4608000,
  SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 0
  * 1 Mar 01:02:41.739: ISAKMP: (0): profile of THE request is (NULL)
  * 01:02:41.739 Mar 1: ISAKMP: created a struct peer 70.1.1.200, peer port 500
  * 01:02:41.739 Mar 1: ISAKMP: new created position = 0x673FB268 peer_handle = 0 x 80000008
  * 01:02:41.739 Mar 1: ISAKMP: lock struct 0x673FB268, refcount 1 to peer isakmp_initiator
  * 01:02:41.743 Mar 1: ISAKMP: 500 local port, remote port 500
  * 01:02:41.743 Mar 1: ISAKMP: set new node 0 to QM_IDLE
  * 01:02:41.743 Mar 1: insert his with his 650AE400 = success
  * 01:02:41.747 Mar 1: ISAKMP: (0): cannot start aggressive mode, try the main mode.
  * 01:02:41.747 Mar 1: ISAKMP: (0): no pre-shared with 70.1.1.200!                     PROBLEM!
  * 1 Mar 01:02:41.747: ISAKMP: (0): pre-shared key or Cert No. address.                   PROBLEM!
  * 1 Mar 01:02:41.747: ISAKMP: (0): construct_initial_message: cannot start main mode
  * 01:02:41.751 Mar 1: ISAKMP: Unlocking counterpart struct 0x673FB268 for isadb_unlock_peer_delete_sa(), count 0
  * 01:02:41.751 Mar 1: ISAKMP: delete peer node by peer_reap for 70.1.1.200: 673FB268
  * 01:02:41.751 Mar 1: ISAKMP: (0): serving SA., his is 650AE400, delme is 650AE400
  * 01:02:41.755 Mar 1: ISAKMP: (0): purge the node-267512777
  * 01:02:41.755 Mar 1: ISAKMP: error during the processing of HIS application: failed to initialize SA
  * 01:02:41.755 Mar 1: ISAKMP: error while processing message KMI 0, error 2.
  * 1 Mar 01:02:41.759: IPSEC (key_engine): had an event of the queue with 1 KMI messages...
  Success rate is 0% (0/5)

  I'm building a lab to find a solution for this.

  The other side is a VPN Linksys router, I tried with an IOS router on both sites also, but I got same results.

  I tried with DPD, ISAKMP profiles don't... no help.

  Hi Smailmilak83,

  Configuration of a static encryption with a specific peer card creates a society of surveillance for the peer. Dns lookup he's now only the first time, he tries to connect, after which it's just going to be her generate a new key. If she would ideally use the value peer in the his and not the config or a dns lookup. So, it is wise to use a dynamic encryption card.

  Please try to use a dynamic encryption instead of a static map. Although there are some limitations including crypto being initiated only at the other end, we can work around keeping the tunnel directly.

  Hope that helps.

  Sent by Cisco Support technique iPhone App

  -Please note the solutions.

• WVC210 DYDNS AND PROBLEMS WITH ACCESS TO THE WEB

  I have 2 Configuration for WVC210 cameras on dydns of deleted I can't see them on the web. I can access via the local network using the ip address and port or the dyndns name and port. The router has listed as a virtual server and I even put one of them is like DNZ (outside the firewall of the router), the port check tools show a port opened from a remote location. And I can ping. But I can't connect to the camera. Also, I was able to view a WVC54GCA camera with the same configuration. Any ideas?

  I can get both of these cameras no problem... just not able to connect but the login box comes right to the top as soon as I hit him enter after you put the URL...

• Management remote WAG120N + DDNS problem

  Hello

  WAG120N has a problem with the connection of remote administration when DDNS is set up.

  Steps to reproduce:

  ===============

  1. enable remote management

  2 Configure DDNS (fe. DynDNS.org)

  3. try to connect to the router using the DDNS name, not IP

  -Online web browser will go to an infinite loop of disconecting/connection to the router

  4 detect the IP address of the router assigned the DDNS name (using the command nslookup fe.)

  5. try to connect to the router using detected IP address, DDNS name no

  -online connection successfully established

  I use 3 different linksys to cisco routers, but only with WAS120N, I have such a problem. Is there any bugtrack system where I can log a bug on this issue?

  Yes, I tried. I see that there is a new version that was released after my message from the forum. I can see that this one has been fixed in the release notes (* happy *). Going to try it...

• WAN problem with DLINK KvD-g1402s WVC210

  My wvc210 works fine on my local network, but I can't access it from the internet. I have read the manual and I have tried several solutions to this forum but still no luck. Who can help?

  WVC210 camera:
  Fixed IP: 192.168.0.99
  Active DDNS, dynDNS provider
  License to access Web alternative 8000

  Router D-Link KVD-G1402S:
  WAN: Dynamic IP address
  LAN: IP: 192.168.0.1
  Virtual server: 192.168.0.99 TWO 8000/8000 Camera

  If I go to http://xxxx.homedns.org/ to get the page of my router for dynDNS configuration works
  If I go to http://xxxx.homedns.org:8000 / get a time out
  If I check the port 8000 on the dynDNS site, he said of "the port is open and accepts connections...". »

  any ideas?

  There was a problem with the router. This router is known for problems with the virtual server...

  problem solved now

• Firmware WRT54GH

  I spent a time looong on Cisco's Web site looking for the firmware for the WRT54GH.  When I click on the tab download - NO firmware or manuals are listed!  Nada! Zilch!

  The problem: my router seems to not be broadcasting my SSID.  I restarted it and still no joy.  I did a Factory Reset and re-entered manually all my settings - still no joy.  So I guess the next logical step is to re-flashing the firmware - but I can't find!

  When I try to log-in to "Live Chat" no "list of countries" doesn't appear in the drop-down list box - it is completely empty.  Is the same for the field after (I forgot what his name)-just a drop-down list box empty.  They are mandatory fields, so I'm stumped.

  So I'm here looking for help from the community.  Again, my question is: where can I find the download of the firmware on my router?  I'll be very grateful if someone could post a link for me.

  Thank you!

  You need to perform an Internet search for the firmware.

• E4200 causing DynDNS abuse

  I just install my new E4200 yesterday and today I received and email saying that my account has been banned do abuse. Probably more update. I know that's not the routers multiple update causes the old one is sitting in front of me and is disconnected.

  I can only assume the E4200, update frequency is high, but there is no way to adjust it. Also, there is no firmware updates.

  Anyone who has another experencing this?

  Well after spending a good half hour arguing with a first level tech and then in now for 20-30 minutes, I was finally able to talk to a technician.   I have to give him credit.   My experience with outsourced support is usually pretty bad (like this until I talk to him about high technology).    To and its Linksys credit, he took the time to listen to me and did some research online of his own.   After having done a bit of work, he told me something that has not been mentioned here.   If you have active DDNS server, every time you click on save settings button on ANY page of the router GUI, it updates all settings - which includes the re-update DynDNS even if the IP address has not changed.  Routers from series 54 G/L did not do that.   Given the equivocation, that I have done with this thing in the last days (playing with the NAS function), I saved the settings MUCH.  So if what he says is true, it could explain the DynDNS blocks that I receive.

  I now have a file number, and tonight, we are trying experience.   I locked parameters from 19:00, and let stand overnight.   It has been almost 4 hours and DynDNS has not been updated - and more important, I have not been blocked.   There has been speculation that the unit is updated when the lease of 6 hours runs, and if this is the case, I should be able to see.   If I make it through the night without updates or get blocked, I think I'll be pretty confident that the problem is understood.   If this is the case, I'll just make sure that I disable the DDNS client whenever I'm fiddling.

  If I'm stuck overnight, the tech asked me to call back with the file number and it will open a bug report.

  Just thought you want to know everything.

  Mike

• Cascade and its effect on DynDNS?

  OK, so for several months, I had a NSLU2 in a DMZ if I could get there by DynDNS and it was functioning 100%.

  I added a cascaded router and other NSLU2 downstairs to develop capabilities and features of my network home.

  I moved the "public" folder on the second (new) NSLU2 and adjusted the DMZ address in the main router in order to take account of the new NSLU2.

  The new NSLU2 is physically connected to the wrt54g (secondary) (operation in router mode, according to the waterfall in the linksys forums), but I can't reach it by dyndns.

  I have reset the demilitarized zone in the original location (first NSLU2), and it still works.

  So, the problem is that I can not knock the new NSLU2 to DMZ. What should I do for the second router to allow traffic coming to it.

  The second NSLU2 IP is listed in the DMZ on both routers. I have tried establishing a route in the main router, did not work. So, how to fix?

  Too bad. It was a PEBKAC.

  Yo soy estupido!

• WRT610N home network problems

  Hello, my network is not working properly at home.  Computers communicate with each other and I can't save on my NAS.  I think that there is a problem with administrators and/or the useres, but I have no idea.  This is the upward.  I'd appreciate any help that anyone can give me.

  (Wireless) LAPTOP running XP SP3.  DESKTOP computer running Windows 2000.  Western Digital MY BOOK (1 TB, call the BIG HD) connected to the WRT610N for NAS.  Western Digital MY BOOK (500 GB, call LITTLE HD) connected directly to the DESKTOP and shared with EVERYONE.  Computers and the router are assigned to the 'HOME' network  All IP addresses are static.  All firewalls have other computers IP Allow or FULL TRUST.  Before adding the WRT610N computers are networked and two external drives we connected to the DEKSTOP and everything worked great using a wrt54g.  The two external HDs were shared and I could read/write in everything on a hard drive of computers.   I could save the laptop via Norton 360 on each disc. Only problem was the speed and I wanted the SIN for the DLNA media service. Since then, I installed the WRT610N and connected to it the BIG HD for the uses mentioned previously.  There are a couple of different issues going on that I can't understand.

  First of all, DESKTOP does not see other computers in the HOME network.  It is always assigned to the HOME network.  Trying to view other computers in the HOME network, that the DESKTOP appears.

  Laptop will show the WRT610N and the OFFICE of the HOME network.  Laptop will be connect/read/write to the BIG HD on the WRT610N. Laptop has no permission to access OFFICE. So I can't go to the SMALL HD on the DESKTOP via laptop.

  This is where it gets really strange.  When you back up PORTABLE HD GRAND via Norton 360, the backup fails after 832 files.  After the backup fails, laptop no longer has permision to access the BIG HD.  Laptop can no longer open WRT610N of icon in the HOME network either.  Does not have permission.  Also, if I try to click the icon for the WRT610N on the HOME network or the icon for the mapped HD BIG in my computer, the wireless signal is de-energized and resets the WRT610.  Laptop gets all rights, and permisions on WRT610N back after restarting the laptop.

  Before attempting the back upward, I made the BIG HD available via FTP and www.dyndns.com.  It worked, I could remotely to the BIG HD from other computers via internet.  Then after that the BACKUP failed, I got an email from dyndns.com saying that my host name has been blocked.  Dyndns.com, three reasons for blocking are ' updates to your client on an interval (e.g. hourly), your client is defective (e.g. flooding), you run several clients. "  I don't know why mine failed, but he did about the same time, I ran back upward.  I know that I don't have muliple customers.  It is the only host name or service or what I use with dyndns.com.  I sent without changing anything on the WRT610N, dyndns.com, asked to be unblocked, and they unlocked my hostname. Have not been blocked since then, but I have not tried a return to the top since I unlocked yesterday.

  It's the last symptom.  In my HD GRAND, all users and "S-1-5-21-789336058-329068152-725345543-5703" are listed as users.  I understand that the long alphanumeric user can be the WRT610N.  I didn't create it and I can't remove it.  I don't know if this user is on the SMALL HD.

  So, how can I get the DESKTOP on the HOME network?  How can I get the LAPTOP and the DESKTOP sharing?  How can I get the LAPTOP to save BIG HD without dropping out and having to restart the laptop (can't get a full backup now)?  This is a problem of 'property' on which device has the HOME network.  I know initially (WRT54G days) I have everything set up by the OFFICE.  It now appears that the property could be made through the WRT610N.  EVERYONE is allowed on each disc shared in the HOME network.  All drives and shared folders have different names.  All the problems occur with all security and firewalls as well off.  I already flashed the firmware and power cycled the WRT610N about 30 times over the 3 months because of the attempts to connect the two HDs at the same time.  The WRT610N seems to be stable except to drop the connection after 832 files during back upward.

  Can someone help me please?

  As you mentioned that all computers are in the same workgroup. Thing you need to check, on your desktop, open the window prompt commands and ping your IP of your laptop and check if you get all the answers, if you are getting answered, on your desktop, click Start - RUN - "\\Laptop IP" and click OK... and it will show you the folder list or the drivers that you have shared on your laptop , Just right-click on it and select 'Map network drive' and below check "Reconnect to the connection" and click Finish. It will be the card your laptop computer drivers shared on your desktop and you should be able to transfer the files from your desktop to the laptop.

  When you ping your laptop from your desktop computer are we can't get an answer, then you can try to disable the firewall and Antivirus on your computer.

  Your router has changed the MTU size to 1300 and click on save settings... That does not solve the problem even if you transfer files from your desktop / laptop computer on the NAS.

• Error FTP WRT54GH 425

  I've been running a FTP FileZilla Server for more than 2 years now. When I arrived in FTPs was actually the first time I had to port forwarding. External router forward 21 TCP 21 on the LAN, everything was good, FTP works. A few days ago the old router died, and to get a new one, I went for a WRT54GH. When I put in place I have also made sure to forward port 21 to the machine. Now, I try to access the FTP and after a long wait, I get an error 425 unable to open data connection.

  I double checked and checked - is not only the port properly transmitted, but FileZilla actually gets the request and the two negotiate a bit. Since I change anything in the FTP and FTP still works fine on the LAN IPs I will of course blame the router!

  What should I do and how can I solve this problem?

  I do usually not reproduced but I fixed it and I leave this info here for future reference to others:

  It seems that - at least with the first version of the firmware - router alters network packets if she sees they are sent on port 21. He changes IPs their LAN PASV commands, which connecting clients cannot work with. In addition it seems that some other obscure port opening the issue once the connection is established.

  In order to circumvent the arbitrary conversion of NAT on the router, you must forward external port 21 to some other internal ports, for example 12345. The FTP server on the computer must be configured to listen on this port. This will get around the NAT issue.

  For the second question, the server PASV mode must be given a range of fixed ports, for example 65000 to 65100, and in turn these ports should be sent to the FTP hosting machine in the settings of the router.

  -Important set of notes on one or more ports forward!

  Ports passed before changing the address LAN IP (e.g. 192.168.1.x to 192.168.0.x) range MUST be disabled, saved and re-checked, otherwise the rules no longer works! In addition, if the SPI Firewall settings are changed in any way, all ports beaches (beaches, ports not only) MUST be disabled, saved and checked in order to work! Yet another note, DMZ seems to have similar problems. Not knowing this topic can lead to unexpected with the implementation results not only the FTP, but also other applications that rely on shipping, because the router will claim a set of settings, but do not use it.

• Problem with Remote Desktop using router WRT54GC

  Hi all.

  My husband and I travel with a computer and an iPhone each, so 4 wireless devices, when we travel, we use the WRT54GC to connect to DSL or broadband from the hotel and then create a LAN in the room using the WRT54GC so we can connect all our devices through the router to the internet.

  Key steps are:

  (1) connect to the router from the hotel to rent a computers IP address.

  (2) do an ipconfig to get the IP address leased the hotel, over the subnet, DNS servers, etc.

  (3) hook a computer into the WRT54GC and give him the IP address and other parameters and clone the IP address of the original computer used to connect to the hotel so that the hotel think that our WRT54GC is the same device.

  (4) connect the router to the wall to talk to the router of the hotel and to connect our devices on wifi LAN created by the WRT54GC and we're good to go.

  Everything works very well and always, but with one exception: we normally use connection software Office Microsoft standard to logon remotely to our computers at home.  We use dyndns to update the IP address of the computer and were marketed in the House so that each computer is accessed through our home router when a query of the DRC between the use of this port forwarding port.

  However, all of a sudden we cannot Remote Desktop our personal computers through the WRT54GC.

  If we put the original computer used to access the router from the hotel directly to the connection to the local network, then there is no problem and that computer can successfully remote desktop, but once we put the router in the equation, we cannot do.

  Any thoughts?  It's certainly something about the configuration of the router, but I checked the firewall and DNS, and those who are not suspects.  The router configuration has not changed in recent years and has always worked previously.

  Any help appreciated.

  Thanks for the tip!

  We have recently started using logmein.com.  There is no charge for simple remote desktop, but the monitor resize and things is easier with it as the version of Microsoft, and for a small fee, you can activate on the management of files, allowing you to do things like file transfer between your home and remote computers easily.  I had tried to do in the past using DRC and it was too slow, but not also with logmein.com.

  That's why we have not been totally freak out the problem, because we had a backup solution with this product, but my husband has a phone in his office, he can connect to while overseas to make calls since in Australia (where we live) while he gets a charge local calls only, and it does not work with logmein , that is why we must get Microsoft DRC will once again!

  In any case, we use dyndns to administer a dynamic update of our IP address for our home router, is to make our computers at home and in a last ditch effort, I had a look at our account and re-joined our IP against our dynamic naming.  Hop, DRC said work again after that.

  It is most strange, because the IP listed was the good IP, but somehow it seemed temporarily do not resolve correctly.

  In any case, it's all fixed.

  At least, it was pretty obvious that it was something somewhere between the router and the House, because of the way he acted. It's usually pretty obvious when your home network has fallen... we knew that is that since we could communicate by other means.

  Thanks for the tip on the other remote tools.  I will certainly check.  There is never too much!

• WRT54GH will not show wireless! Help!

  Hello to you all,.

  I have a serious problem with this template WRT54GH.

  It is configured with automatic DHCP, plugged into a DSL cable modem to use on a Mac OS 10.6.6 and Win7.

  I used the connection wireless with no problems until today. Suddenly it will not broadcast my connection Wireless by all means!

  I have already created a new connection, tried multiple SSID, passed to B, G, I tried WEP, WPA, different channels, even with the SSID broadcast enabled/disabled and I cannot find the router on any computer.

  I already updated the firmware, reboot the router to the factory settings and tried every tip on the support of Cisco, Google and always avaiable not game.

  The ethernet cable works perfectly, from where I am accessing internet now, but I guess that's not the proper use of a wireless router...

  Can anyone help me on this issue?

  Thank you!

  After all, it was a problem with the router.

  I got this problem change for a new!

• Programs like Windows Mobile Device Center and DynDNS Updater hangs

  I am facing this problem with several software. When I try to launch Windows Mobile devices, it crashes or closes just without any notification. A window pops up saying Windows Mobile Device Center has stopped working and gives only 2 options closing program and 2nd-check online for a solution and close the program. It is the same with other software like DynDNS Updater 4.1.6 I downloaded from http://www.dyndns.com/support/clients/ . Windows mobile device center window details of the problem as below

  Description:

  Stopped working

  Signature of the problem:

  Problem event name: CLR20r3

  Signature of the problem 01: wmdc.exe

  Signature of the problem 02: 6.1.6965.0

  Signature of the problem 03: 465eefc9

  Signature of the problem 04: mscorlib

  Signature of the problem 05: 2.0.0.0

  Signature of the 06 problem: 4889dc80

  Signature of the problem 07: f51

  Signature of the 08:0 problem

  Signature of the problem 09: N3CTRYE2KN3C34SGL4ZQYRBFTE4M13NB

  The system version: 6.0.6001.2.1.0.768.3

  Locale ID: 1033

  Pls Help, I don't want to swith back to XP as Active sync and this software works fine on XP. I think it's the problem of compatibility of programs with Vista
  I use Home Premium Version SP1 and I don't have the same day once because after the previous installation, my PC got slower after full update.
  My configs of machine are
  Dell XPS M1330 Laptop
  T8100 processor
  965 mobile chipset
  3 GB RAM
  HARD DRIVE 320 GB

  Dushyant salvation,

  • You have security software installed on the computer?
  • Since when are you facing this problem?
  • You did changes to the computer before this problem started?

  Before solving the problem, I suggest to create a system manually, Restore Point so that in this case, a problem occurs when performing these steps, you can always perform a system restore.

  Step 1

  Uninstall Windows Mobile device under Windows Vista programs and features. Access the link below and follow the steps in the article to uninstall the program.

  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

  Step 2

  Follow the steps below only once you have backed up the registry.

  a. Click Start, in the search box of start, type regedit and press ENTER.

  b. If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  c. in the navigation pane, locate the following registry subkey:

  d. in the registry editor, navigate to the following location: HKEYCURRENTUSER > SOFTWARE > MICROSOFT > WINDOWS CE SERVICES > PARTNERS

  e. check the keys referencing your mobile device and right-click on it and remove the keys.

  Note: The problem may occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, follow the steps in the link below:

  http://support.Microsoft.com/kb/322756

  Step 3

  Restart the computer and download the Windows Mobile device Center on your computer the link below and install it and check if it works fine without any errors.

  http://www.Microsoft.com/windowsmobile/en-us/downloads/Microsoft/Device-Center-download.mspx

  You can also uninstall and reinstallDynDNS Updator 4.1.6 program and check if it works very well.

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Leave the connection due to release/renew IP address problem

  Hi there - I have an Inspiron 23 model 5348, connected to a router of the BT Home Hub 5 running Windows 8.1. Whenever I wake the computer from sleep mode and often even to start it upward, that I have no internet connection. I have release/renew the IP address, and the connection is re-established for a period of time.

  This happens on my inspiron wired or wireless connected. I updated the router, changed the wires, reinstalled the drivers for network devices, changed the term of the lease on the router for 21 days and used a static IP address, bit, nothing seems to work.

  It only occurs on the Inspiron. None of my other devices give up their connection.

  Any ideas what is the cause?

  For anyone else having this problem this page should sort

  http://forumhelp.dyndns.info/networking/staticip.html

• DynDNS and NAT

  Hello

  Being new in the Cisco field, the notement in CLI, I have two small problem that may be related.

  The LUN DDNS update is not done and not of the NAT doesn't work, someone could maybe help me

  Here is the config of the CISCO881-K9

  !
  !
  !
  !
  IP dhcp dns update both
  no ip bootp Server
  no ip domain search
  IP domain name dyndns.org
  8.8.8.8 IP name-server
  IP ddns update dyndns method
  DDNS
  !
  IP ddns update method wellmess6780_dyndns
  HTTP
  Add http://MyLogin: [email protected] / * //nic/updatesystem=dyndns&hostnam e =& myip =
  remove http://MyLogin: [email protected] / * //nic/updatesystem=dyndns&host name =& myip =
  maximum interval 0 0 30 0
  minimum interval 0 0 30 0
  !
  DHCP-client update dns server IP times
  IP cef
  No ipv6 cef
  !
  !
  license udi pid CISCO881-K9 sn FCZ164091N8
  !
  !
  username privilege 15 secret 4 thierry hxs3I1G5/VfWpIztplmqsbnfWy7MCP3fSM9VloHus 9 q
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  interface FastEthernet0
  LAN description
  no ip address
  !
  interface FastEthernet1
  LAN description
  no ip address
  !
  interface FastEthernet2
  LAN description
  no ip address
  !
  interface FastEthernet3
  LAN description
  no ip address
  !
  interface FastEthernet4
  no ip address
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  automatic duplex
  automatic speed
  PPPoE enable global group
  PPPoE-client dial-pool-number 1
  !
  interface Vlan1
  Description $FW_INSIDE$
  192.168.16.254 IP address 255.255.255.0
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP nat inside
  IP virtual-reassembly in
  IP tcp adjust-mss 1452
  !
  interface Dialer1
  IP ddns update hostname wellmess6780.dyndns.org
  IP ddns update wellmess6780_dyndns
  the negotiated IP address
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP mtu 1492
  NAT outside IP
  IP virtual-reassembly in
  encapsulation ppp
  Dialer pool 1
  Dialer idle-timeout 0
  persistent Dialer
  PPP authentication chap callin pap
  PPP chap hostname [email protected] / * /
  PPP chap password 7 01125F575611505C38
  PPP ipcp dns request
  No cdp enable
  !
  default IP gateway - 192.168.16.254
  IP forward-Protocol ND
  no ip address of the http server
  IP 8088 http port
  23 class IP http access
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP nat inside source static tcp 192.168.16.99 80 80 Dialer1 interface
  IP nat inside source static tcp 192.168.16.99 21 21 Dialer1 interface
  IP nat inside source static tcp 192.168.16.99 Dialer1 1433 1433 interface
  IP nat inside source static tcp 192.168.16.99 3389 3389 Dialer1 interface
  IP nat inside source static tcp 192.168.16.99 Dialer1 3160 3160 interface
  overload of IP nat inside source list 100 interface Dialer1
  IP route 0.0.0.0 0.0.0.0 FastEthernet4
  IP route 0.0.0.0 0.0.0.0 Dialer1
  !
  access-list 100 permit ip 192.168.16.0 0.0.0.255 any
  access ip-list 100 permit a whole
  not run cdp
  !
  !
  !
  Line con 0
  local connection
  line to 0
  line vty 0 4
  access-class 23 in
  privilege level 15
  local connection
  transport input telnet ssh
  !
  !
  end

  Hello

  no ip route 0.0.0.0 0.0.0.0 FastEthernet4

  no access ip-list 100 permit a whole

  Kind regards.

  Alain

  Remember messages useful rate.