WRV54G: question of firmware upgrade

Similar Questions

• WRT610N firmware upgrade question

  I have a simple question about the firmware upgrade.  I want to know if it's OK when the upgrade of the firmware on a wireless router for rather than press reset and rest for 30 seconds, that I connect with my browser and 'load Factory Deaults?

  I read, where they are supposed to do the thing of the SME and the method of web browser is much easier worth me.

  Can anyone confirm this or should I press the button to reset for 30 seconds?

  see you soon

  It is advisable to reset the router after the upgrade of the firmware. For once you upgrade the firmware on the router... Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now, you can re - configure your router.

• BDX4350KB Wifi adapter and firmware upgrade doesn't work do not

  It is a sequel to my earlier question about if the WLM-20U2 Wifi adapter will work in my blu - ray player.

  After buying the adapter I plugged it and a message 'not supported', if I tried to connect wireless it says there was no an adapter connected.

  So I assumed that this necessary upgrade, so I formatted a 1 Gb USB drive with the FAT file system, downloaded the file level (version 39 http://www.dl.toshiba.com/player/NA/GB/EN/BDX4350KB.html) and copied the file .bin on the USB.

  When I plugged into the player and said to check the disk for a file to update it tells me that "frontend file is not found"... There was only one file to download, and it wasn't in a folder so I guess I'm supposed to just copy that file on the USB drive.

  I checked the USB port with a memory stick with photos on and it works fine.

  How to get the upgrade to work in the hope that it will enable the wifi adapter to work?

  Thank you

  Have you checked the guide in PDF firmware update?
  [Update firmware BDX4350KB | http://fget.dl.toshiba.com/manual/install/10009/Installation_Instruction.pdf?fromPid=%2Fplayer%2FN A%2FGB%2FEN%2FBDX4350KB.html&f=Installation_Instru ction.pdf]

  _ * How to upgrade the F/W * _

  (1) update firmware requires the USB of size max.2GB. Please make sure you format the Flash DRIVE to FAT/FAT32 before you start the upgrade procedure.
  ? Create a new folder on the USB drive and name it UPG_ALL
  ? Unzip the firmware file and copy it in the folder UPG_ALL.

  2) turn on the BD? Drive and make sure that you can see the player's on-screen Menu.
  ? Insert the USB key containing the Firmware upgrade file in the USB of the Blu slot? ray player

  3) press the "SETUP" button on the remote control.

  ? Select keys on the remote control UP/DOWN
  ? Symptom
  ? Upgrade
  ? USB storage device

  4) press the OK button on the remote control depending on the USB storage device.
  ? Now the upgrade file is under research. Please wait massage will appear

• SGE2010 - Firmware upgrade and config does not save

  Hi all

  I have a few questions, but ill start with what im trying to achieve.

  With the help of the EMS 2010 for Microsoft NAP with 802.1 x auth for access to the switch, which has led to some questions

  What I have: an EMS 2010 48 port switch firmware 3.0.0.17

  Firmware update: to ensure im not having not problems due to the old firmware, I tried to upgrade using ros_ls1_bp_ge_bx - 3020.ros to 3.0.2, by downloading the file through TFTP, the transfer is complete and that's all, nothing happens.

  Restarting the device: as part of the upgrade process, I thought I might restart, so I rebooted and found that all my settings were cleaned, as if a reset occurred... and add further pain, the backup of the settings I had taken do not appear to introduce themselves with a new request.

  NAP support: so I tested my server NPS (RADIUS) with NTRadping.exe and everything is good, however I can't the SGE2010 to talk to it... the authenticator State in the web interface is still listed as initializing... I'm not sure if it is a simple mismatch (where the attempt of a firmware upgrade), a tag that should be on the side of RADIUS or switch misconfig.

  So, in summary:

  (1) how the hell you upgrade the firmware?

  (2) why are none of my saved settings to restart the device?

  (3) if anyone one of them puts up with PAN and has all wisdom of bone beads, let me know.

  Hi Ben, once you update the firmware, you need to go to the active image, apply the second image. Restart the unit. Regarding the configuration of switch, you must save the configuration running at startup configuration

  Admin-> file management-> copy files (running at startup)

  -Tom
  Please evaluate the useful messages

• A few questions about the upgrade on Satellite A300-144

  Sorry for the typos, English is not my mother tongue.
  I want to ask some questions about the upgrade of a300-144.

  * Some info first.*

  CPU: T2370 ([http://ark.intel.com/products/34445/Intel-Pentium-Processor-T2370-1M-Cache-1_73-GHz-533-MHz-FSB]).
  Chipset: GM965 ([http://ark.intel.com/products/29821/Intel-82GM965-Graphics-and-Memory-Controller]).

  * Questions.*

  1. my frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  2 Intel said that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?

  3 I know, taken of my CPU is μFCPGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 ([http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB]) is a compatible processor or there are some limitations in the BIOS?

  > 1. My frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  The speed of the memory is related on the material. This means that the FSB is responsible for the limitation.
  If the FSB would allow support 667 MHz then the memory would also at this speed.

  > 2. Intel says that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?
  The memory depends on the chipset. So if the chipset supports 4 GB of RAM, you should be capable of this move to 4 GB of RAM

  > 3. I know, my CPU is? FC-PGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 (http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB) will be a compatible processor or there are some limitations in the BIOS?

  It might be possible that the new processor would be fully supported by the BIOS, but in most cases it should not be a problem if the chipset would support the new processor.
  But as far as I know the upgrade of the CPU is not supported by Toshiba or any other manufacturers of portable and its your own risk to run laptop with the new processor.

• 200 d IOmega IX4 Firmware upgrade failure

  Hello

  I have an IX4 - 200 d which I inherited. Initially, it wouldn't boot and display only the symbols of USB stick/network after about 60 seconds.

  With some searching on Google, I created a boot disk USB with the firmware updated on this issue. All goes well until the Firmware upgrade begins. I go to the step of (what I assume is) the upgrade of the firmware and it gets 75%, hold for 5 seconds and then the machine stops.

  I tried to repeat the update of the firmware with all the drives present, with every other drive in the first slot and with all the disconnected drives. But it seems to behave in the same way.

  Is this a known issue? Or could it be a hardware failure?

  I'm pretty eager to find a solution - it takes a long time for me to accept defeat.

  The only other suggestion that suggested Dr. Google is to start linux and reformat the hard drive?

  Any help is appreciated.

  Kind regards

  Pete

  Hi André,.

  This case can be closed.

  After the above mentioned procedure eventually work, I didn't know that - ALL readers should be present and formatted during an attempt of USB firmware update / install.

  The link again on the forum - http://forum.nas-central.org/viewtopic.php?f=14&t=4401

  This seems to be the only solution.

  Kind regards

  Pete

• Jump and mix tracks after firmware upgrade?

  I can't explain it. Since the latest firmware upgrade Fuze my wife started jumping titles (for example jump to the next song to halfway through the current), but a funniest part - he mixes parts of files. We can listen to a song, and then all of a sudden he would be interrupted by 1 second of a file from a different album and then come back to play the first song from the point it was interrupted. What gives?

  Me that was too much.  I downloaded all my music back and reset my Fuze and reformatted it.

  Charge of excessive songs and back on went.

• BEFW11S4 v.4 and Vista - firmware upgrade failure

  Hello

  I've had this router for about 5 years, it runs with XP without any problem. Since I got a new laptop with Vista, the wireless connects for an hour or two, and then falls back and I have to unplug the router for five seconds, then reconnect to reconnect (my other laptop with XP has not this problem).

  I understand that there is compatibility between the BEFW11S4 v. 4 and Vista problems so I tried to update the firmware of dartybox.com and kept getting a message that failed. I hard rebooted the router but button of restart 30 seconds and the upgrade has always failed. I so re-set to factory settings through the online admin to the router, re-uploaded the implementation level and still got the emssage failed (I am sure that the model number & version is correct and I download the appropriate firmware upgrade).

  Is there anything else I can do another one) buy a new router; (b) living with school drop-outs; (c) remove Vista and go back to XP?

  Thank you

  Bigdank

  Genius! I have changed the name of code.bin, went to the admin > tab upgrade firmware and the upgrade file. I had a wireless without interruption ever since, even after the awakening of the laptop to sleep.

  Thanks for your help

• BEFSR81 Firmware Upgrade Gone Bad?

  Just putchased a new BEFSR81 router.  Using the installation CD, I got it Setup and works very well.  Then, I went to the support of Linksys and found page a more recent version of the firmware.  My version is 2.51.4.  I downloaded the 2.51.4.6 version and installed. I made sure to choose the version for my model 3.1. He appeared to install OK, because I got the message that it was for the page in 5 seconds.  Now I can't go to the web-based configuration page.  I can ping 192.168.1.1 and get a normal response, but by entering that address in my browser just times out.  I turned off the router and even held the reset for 30 seconds, but don't can't go in the web-based configuration page.

  This router is now watered?  Do I need to send it back?

  Thanks for any help on this.

  Found the answer in this thread:

  http://homecommunity.Cisco.com/T5/wired-routers/failed-firmware-upgrade-bricked-BEFSR41-v4-3/TD-p/25...

  Thanks Wizzard!

• The Linksys BEFSR41 V2 Firmware upgrade help

  I can't open the MacBinary (.bin) files that I downloaded from linksys, in order to update my firmware. I used my utility to archive, Stuffit Expander Mac and BetterZip, and so far none of them opens the file. Anyone have the firmware upgrade in a different format or advice on how to solve my problem.

  Do not touch the file you downloaded. The only software that uses it is your browser.

  You must open the web interface of the router at http://192.168.1.1/ and then use the upgrade of the firmware here.

  I don't know if the demo user interface is always up to date, but if it is as you should find it on the help page. See here. Click Update Firmware. Then, press the Browse button and select the .bin file that you downloaded. Then press upgrade and the browser will download the file on the router.

• WRT 160NL firmware upgrade ever end!

  Hello

  I am trying to upgrade the firmware version 1.00.01 B15 to 1.00.01 17 (the only one available on the linksys Web site). It is not allowed to turn it off or reset it. However, the upgrade progress stopped at 98% and never ending so far. Should I wait longer (another day)? Or I can just reset/power off of the it?

  Attached is a snapshot of the screen for reference.

  Thank you.

  

  The firmware upgrade process must be complete...

  Try the following steps... Press and hold the button of reset for 60 seconds... Release the reset button and unplug
  the power cable from your router, after only 30 seconds reconnect the power cable...

  Now, as do the settings of the browser on the computer... Open an IE, click Tools > Internet Options, and then delete all files, cookies, history, forms... GoTo 'Connections', make sure never Dial
  a connection is checked, click on network settings and make sure that all the options are unchecked... Once you are finished, click OK... Close IE and reopen...

  Now, try to upgrade your router firmware... it should work!

• After restart of the firmware upgrade

  Hi, I need to update the firmware on my controllers PS6100 EqualLogic.

  I found the instructions on how to do it and everything seems straight forward to do so via the GUI.

  I noticed there is a necessary restart after the firmware has been applied. Does this mean I have to gracefully shutdown the virtual machines running on my SAN LUNS? My iSCSI connections will be closed/broken during the restart of the post firmware upgrade?

  Thank you, Oliver.

  Hello Oliver,.

  In the same area download notes firmware and release is another PDF, entitled ' iSCSI initiator and optimize your SAN environment for high availability operating system considerations ", which includes some key parameters that will allow your computers virtual and servers through the failover time.  It is important that not only the Firmware update, but in the case of an unexpected failure due to a failure of CM.

  More if you use VMware ESXi, there is a best practices PDF for that as well.  In addition to better manage the failover, these changes have shown to improve performance as well.

  The Tech report TR1091 is available here:

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20434601/download

  Changes for Windows and the knots of ESXi virtual machines will require a reboot to take effect.

  What version of firmware you are at, and what version you are migrating towards?

  Other things I always propose updates is to ensure that both controllers are plugged in your switch and in the VLAN correct.  Since assets CM are failed over to the passive, support gets much advertising is unable to access the storage after firmware update.  Or ports of the day before were not in the VLAN correct, or individuals with disabilities, etc...

  It is for these reasons that personally I prefer to do the updates via the serial port CLI.   The process is more talkative, and if something should go wrong, you need the serial port of some sort.   Since the installation and tested in advance is a huge time saver.   Here, we use serial mux so that all array controllers are easily accessible.

  Kind regards

  Don

• Firmware upgrade question

  I have a Zip Clip + and a Clip. I was wondering if the firmware used by the two players is the same. The reason I ask, is this evening I was asked to upgrade (Clip Zip +) but I can't upgrade the Clip.

  The Clip shows V01.02.16P, then the clip Zip + is using V01.01.20A. I tried to update the Clip but for some reason, the update does not appear, there is a new version. Is this good? Thank you.

  What you probably, it's a Clip + and a Zip Clip. No, they do not use the same fimrware. 01.02.16 is the latest firmware for the clip + is why the updater does not provide an update.

• PhotoSmart 6520 firmware upgrade questions

  Greetings!

  I had no problem with my printer, until I "upgraded" from Win 7 to 8 Win. Initially, he printed for a few days, and then he stopped. I've uninstalled and reinstalled the driver at least twice. I tried the HP print and Scan Doctor, who finally found the printer, but still couldn't print the test page. Then I tried HP Diagnostic Utility, which managed to do print and make a copy. But it would not print regular documents. Then I found the firmware update for my printer, who, by description, it looks like it will completely solve my problem. I go as far as the screen that says to make sure that my printer is connected via USB, powered to the top and not in an error state. Check, check and. Then when I hit the update, it tells me that the update of the device can not move forward, and ensure that my printer is connected via USB, powered to the top and not in an error state. The display is normal, the cables are well connected, etc.. Help, please!  I'm terribly frustrated.

  Thank you

  Grace

  This thread has been locked, for more information on HPPIW, please refer to the following support document:

  http://support.HP.com/us-en/document/c02681060

  HP printer Installation Wizard is an application of HP support that helped to download printer software. This support request is no longer supported by HP. This software was last updated was September 22, 2015.

  To download and install the latest version of the software for your HP printer, please visit 123.hp.comor HP support Web site, HP Support Assistant (in English).

• The phone Firmware upgrade question

  Hi I am upgrading the firmwares a lot of phones.

  Current firmware

  SCCP41.8 - 5-3 216

  SCCP42.8 - 5-3 S 3675

  SCCP42.9 - 2-1 S 13

  P00308010200 25

  Required firmware

  SCCP41.9 - 3-1 SR 1-1 S

  SCCP42.9 - 3-1 SR 1-1 S

  Can I go directly from the existing versions or what I need to do step upgrades?

  Thank you.

  Hello

  You can upgrade directly. The release notes says:

  For all SCCP firmware version firmware updates versions prior to version 8.3 (3) to Version 9.3 1 or

  later, you must upgrade your firmware of the phone to an intermediate version (8.3 (3) 8.5 (2)), then

  9.3 upgrade 1.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/cuipph/7900_series/firmware/931sr3/P790_BK_R6CE16B3_00_rn-9_3_1sr3-7900-series.PDF

  In your case, you are already using 9.2(1S) and 8.5(3s)

  regds,

  Aman