WTA on battery and AC connector

Product name: HP ENVY Sleekbook 4

Running window 8 64 bit

Aboves is information about my ultrabook who bought in the last week.

Here are my questions:

1. If the battery is crushed, then I continue to load without plugging the AC cable, done it will overcharge my battery overcharged battery accordingly so the battery/life cycle will degrade?

2 since it's built in battery which consider as non-removable, if the Board is connected to the computer, should I only use alternating current without the use of my battery?

3. I heard a developer who told me that each ultrabook is built in battery use or known as a seal, he also said that laptop has a built in battery is good to keep load even if the battery is 100% because the computer will be automatically discharged once the battery is trodden and without harming the battery/life cycle. Is this true?

You can set the range in which the battery may charge inside the properties of power advanced via the control panel. I recently worked on a Samsung Ultrabook which has been set in the BIOS and Windows Power properties don't no the battery beyond 80 percent. This prevented a discharge/charge to register as a cycle and will prolong the life of the battery at the expense of a bit less runtime. You can also set the battery so it does not start a refill, IE less than drops of battery below 90%, that accomplishes the same thing. I would say that it is especially important on a unit with a sealed battery. You want the battery to last as long as possible. Yes when the AC is plugged in the power to run the laptop comes from 'sector' and not the battery, but some of the "power" is diverted to charge the battery if the load is low enough.  You don't need to worry about the memory effect. In other words, you can recharge anytime (as you say, 74%) and there will be no negative impact on the battery.  This was also true for at least 15 years being portable batteries or-Cad. At that time that he had to leave the race before battery start to load, or you would never go lower that you started to reload... called effect memory. Now a thing of the past, even if you still hear a lot of people say run a battery of laptop to say 10% when get you it and then reload... absolutely useless.

Tags: Notebooks

Similar Questions

  • Satellite P10 switch randomly between battery and AC

    I have a satellite P10 who had some problems of strange power for about a year now.

    My laptop switch to the power of the battery even when it is plugged. I will then either use the computer until the battery runs out and turned it off or Hibernate in until the battery may charge.

    I thought that I had fixed by downloading and installing a new Bios from the toshiba site, which seemed to work for a while, but now it the problem seems to have returned.

    I also bought a new battery and the bar of power, thinking that was the problem... but it does not solve the problem.

    Someone else out there with similar problems, or a method to solve this?
    any thoughts would be great.

    Hi man,

    I had similar problems with my machine, so you can check some things:

    -When the CA is connected, then move him soft in all directions, there are maybe a few micro cracks on the AC connector.
    -try to boot your machine without the battery, your motherboard charging system is may be defective
    -Discover an another AC adapter, maybe the CA is defective

    If you encounter some strange phenomena as power cuts or no charge while you perform this action above, then you have definitely a hardware problem and you will need to contact your local dealer or the service partner for the other instance.

    So I had to do, and it's a faulty motherboard.

    Hope I could give you some ideas.

    Welcome them

  • 0% Apple pencil battery and does not load

    I use pro iPad Apple pencil to draw every day, and I noticed that my Apple pencil stopped working today.

    I plugged in the charger with the pencil and iPad widget, it shows that there is 0% battery left and the lightening bolt charge appears. Cool for 30 minutes, that the battery is always 0%. Unplug the charger pencil crayon disappears immediately of the widget. The same thing happens if I plug the pencil in the port of the iPad.

    I tried hard restart my iPad, rematching in pencil, but still a pencil appears in widgets display 0% battery and load relief icon and by unplugging the charger pencil / iPad disconnects the pencil of the iPad immediately, regardless of the duration of the load.

    Anyone had the same experience before?

    Make sure that the lightning connector is fully engaged in the iPad or the charger. When connected to the iPad, the cover of lightning in the pencil should snap.

  • HP pavilion dv 7 ev 4050: new battery and new charger

    Hello! I'm looking for new battery and new charger for my laptop but I'm not sure to buy... any help? also want to know the measures of the charger plug.

    Hello

    You can buy as mentioned below

    Product features:- http://support.hp.com/vn-en/document/c02260459

    Entry on HP Part # 613154-001 - AC Smart adapt (120 watts) - 100-240VAC, 50-60 Hz, 2. 5A - 18.5VDC output, 6. 5 a, 120 watts, PFC - requires separate cord 3 supply with C5 - charger connector wires

  • Battery and Wifi info not displayed after updating IOS 10

    After upgrading to IOS 10 I have more information at the top of my home screen line. He comes to the line with WiFi, battery, and other info. I see it if I open an application, only some however. This status being lost, it is difficult to look at the life of the battery.

    How do I turn it back on?

    If it cannot be enabled by the user, then Apple needs to bring him back.

    David

    Hello! You can activate the in your settings. Go to battery and select on the percentage. The other options that are displayed on this bar, you can also turn on in general settings. Make sure that the WIFI is enabled in the settings. I had this happen before. After trying your settings, if you still do not see the bar with all the status restart the device. If it still does not work, you can try to recover the device on iTunes. The last resort would be to call the Apple support. I'll try to fix it in the settings that the lines may be busy.

  • I just replaced my battery and it says 'battery of Service '? The battery is new. I need to reset something?

    I just replaced my battery and it says 'battery of Service '? The battery is new. I need to reset something?

    Try resetting the SMC http://support.apple.com/kb/ht3964

  • How to fix stuck battery and automatic when restart updated ios 9.3.3

    How to fix stuck battery and automatic when restart updated ios 9.3.3

    Lambung writes:

    How to fix stuck battery and automatic when restart updated ios 9.3.3

    What do you mean battery stuck?

    the basic troubleshooting steps are: reboot, reset, restore from a backup or restore as a new.

  • My Apple TV Remote no longer meets the high command. Change the battery and restarting did to help. Anyone have any ideas?

    How can I fix an Apple TV Remote that has stopped responding to the command "up"? It works otherwise, but do not be able to scroll to the top is awkward. I tried to change the battery and restart.

    Money or Siri remote? How old is it? He fell on a hard surface?

    TT2

  • my phone has port and new battery and still will not hold a charge

    my phone has port and new battery and still will not hold a charge

    What do you mean 'there port and new battery? If someone other than Apple has opened and replaced the things, it is now unbearable.

  • I use my MacBook Air as a desktop computer. Should I leave the charger plugged all the time or should I drain the battery and then recharge? What is the best for the battery?

    I use my MacBook Air as a desktop computer. Should I leave the charger plugged all the time or should I drain the battery and then recharge? What is the best for the battery?

    Keep the computer plugged in whenever possible.

    If you keep the computer always connected, make sure that at least twice a month

    Run it on battery until battery charge level falls to about 40-50%.

    Please don't completely discharge the battery. Discharge the battery completely will reduce wear and tear on the battery.

    For more information:

    Section: To optimize the battery life

    http://support.Apple.com/en-us/HT204054

    Citing at the bottom of the linked article.

    "The question is often asked:" should I disconnect my laptop from the mains when not in service? Under normal circumstances it should not be necessary because as soon as the lithium-ion battery is full, a properly functioning charger will stop the load and load the pad will only engage when the battery voltage drops to a low level. Most of the users do not remove AC power, and this practice is safe. »

    http://BatteryUniversity.com/learn/article/bu_808c_what_the_user_can_do

  • I need to replace the battery and AC adapter of the Satellite Pro U400-160

    I have a Satellite Pro U400-160.

    I need to replace the battery and the charger of my Toshiba, but I am wary about compatibility issues.

    Any battery for Satellite Pro U400 is suitable for mine?
    As I can't find which batteries are specifically suitable for my computer.

    (For example: is this a: http://www.amazon.es/Bater%C3%ADa-Toshiba-Satellite-U400-11V-7800mAh/dp/B0051A9Y88/ref=sr_1_cc_2?s=aps&ie=UTF8&qid=1366885340&sr=1-2-catcorr&keywords=satellite+pro+u400?)

    Is there a quick way to check if a battery / charger are compatible?

    Each battery and adapter you get from Toshiba has specific part number. All you have to do is use this same part number and order. You should be able to find on the internet.
    You can also get compatible parts you are ordering by the Toshiba authorized service provider in your country.

    By the way: all U400 models have the same construction and the similar specifications then all the batteries specified for U400 can be used on your U400-160.

  • Satellite A210 - battery and no boot

    Hello!

    I used my about 4 years by Satellite A210BX as usual two days ago. The next day, I wanted to start the computer, but it does not start. Just brought an error message indicating "dead battery"... So I searched the Toshiba site and found that it might be the RTC battery for the time and date settings. The laptop battery was fully charged during the last night, but it still does not boot to the top. Just a black screen and you can hear the fan running. But nothing else. No BIOS, no letters on the screen, just nothing :-( If the laptop is loaded via a regular power outlet in the front of the case three LEDS are on (the cable, the SDNA circle battery smbolshe). All three symbols are blue, flashing light.

    The advice I can do now? I found an article on the battery to charge for a few hours when the laptop is on RTC.
    I will try that today. AY of other things I can do now.

    Thank you very much
    Florian

    Hey,.

    I doubt that this has something to do with the RTC battery. This battery can be charged if the laptop is connected to an AC adapter for 24 hours, but this should be mentioned in the user manual

    Can you start the laptop with AC/DC adapter only?

    If this is not the case try removing the battery and the AC adapter for an hour and then test it again.

    In the worst case, it s a hardware malfunction and it would need you will need to contact the technicians of laptop for help :(

  • Strange battery and/or AC on Satellite M30x and Vista behavior

    Hi all!

    I have Windows Vista and laptop M30X on board. Since a few days ago something strange was going on.
    Sometimes (can not know when) system is suddenly goes to the battery. Sometimes the two LEDs of AC and battery are flashing (rappid on and outside) and sometimes one battery LED going off (whithout flashing). When I remove and replace taking AC, everything goes back to normal for a while.

    I checked the Jack - nothing happens when you move (so I think that's not bad taking question). Battery works also very well (on 2-2, 20 h under Vista).

    Anyone has idea what is happening? It would be Vista ACPI question? He must check on another system, but it is quite difficult to reinstall all things repeatedly.

    How I tested AC power, battery, and other stuff to find out what is happening? And most importantly - how to reach or where to set?

    --
    Will be happy for all help!
    V

    PS. just he curled for any race day - nothing has past. So I guess, this problem is only when the laptop is moved (eg. organize, towers and woking on it). I think it means that electronics and OS are good, the question must be somewhere on the cable or / and socket - am I good?

    Post edited by: VirPL

    Hello

    > Could it be Vista ACPI question? He must check on another system, but it is quite difficult to reinstall all things repeatedly.
    I don t think that this problem has something to do with the software or installed Vista.

    I think it sounds more like an electronic power supply malfunction.
    You should check the pins of the battery and if the AC adapter cable is not broken.

    If the output voltage of the adapter is abnormal or if power outages, AC flashes orange.
    In your case the two LED flashes orange and so I think that it s a hardware failure.

  • Tecra 8100: Question on battery and adapter

    I had problems with my 8100 stopping himself so I returned to the store and he exchanged the battery, he only gave me a battery 10.8V my charger and the laptop 15v and are now my charger cable started to melt and melted through the carpet.
    so I need to know, is a 10.8v battery and charger 15v compatible and is it causing overheating or do I have a different problem?

    Help, please

    Hello Diane

    Your device needs AC/DC charger with PA2444UE part number. It is AC 100 - 240V to AutoFix, 50-60 Hz, 15 V, 4 A, 60 W charger.

    The battery is key to the 10.8 V Lithium-ion, 4 500 mAh with PA3009U-1BAT part number. Please don't over use the unit and immediately contact partner in your country. On this path, it is not easy to tell what can be the problem and the unit needs to be checked.

    Don't risk anything and check the unit. Your dealer can give you an address of the service partner or you can visit this page http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true.

    Good bye

  • Problem of battery and power adapter - on LINUX with [b] Satellite L10 - 102 [/ b]

    Hello
    However, I installed Linux.I trying from last month.
    I installed and tired some type linux: Mandriva 10.1 OE, Mandriva LE 2005, kurumin and Knoppix 3.8, kurumin 3.0 4, kanotix (last rel.), suse 9.1, kubuntu 4.0...
    I have installed a large number of linux applications: kacpi, toshutils, fnfx, tools, portable mode, some patches to the kernel acpi acpi...
    I met some of the nuclei: 2.6.8 - 11mdk, 2.6.9,2.6.11, 2.6.12...
    However, I can't battery and adapter sector-info-States on linux.
    What can I do?

    Hello

    I'm sorry I don't have an answer for you, but a suggestion:
    go to this page:

    http://newsletter.toshiba-tro.de/main/index.html

    and request a test for this model, perhaps they can give you some comments.

    BR
    Tom

Maybe you are looking for

  • Can I move close, reduce, maximize button to the left in mode full screen?

    I use ubuntu 11.10, and I'm used to having close, minimize, and maximize on the left side. So I would like to know if it is posible to move these buttons in mode full-screen to the left.

  • Powered by DNSUnlocker

    Hi all I use iOS iPad Mini 2 8.3. I found untimely when popup they surf the net by Safari. "Powered by DNSUnlocker" and "ad DNSUnlocker" always appear on the online shopping site and some blog site. I did erase history data and the Safari Web thru si

  • Synthesis of filter multiband in LabVIEW

    Hello Y at - there some facility in LabVIEW that allows to synthesize the multiband filter, or to use another tool like Matlab. Thanks in advance Paavel.

  • Re: Why the printer set up the process won't accept my valid zip code?

    I'm having the same problem.  I'm trying to install the software for my new printer 3630.  I'm stuck for a valid postal code.  I do not order or anything else, just my printer registar.

  • Help and support button and system restore xp

    When the message by clicking on help and support menu start, Windows can't find 'helpctr.exe. Make sure you typed the name correctly, and then try again. To search for a file, click the Start button, and then click search. Possibility of system resto