WUSB600N temporarily lose connection (do not drop the connection)

Similar Questions

• My pro iPad connects to the WIFI, but loses connectivity to drops in use.  My other IOS devices (iPhone, macbook, etc.) do not have this problem.  Ideas to solve?

  My pro iPad connects to the WIFI, but loses connectivity to drops in use.  My other IOS devices (iPhone, macbook, etc.) do not have this problem.  Ideas to solve?

  Hello BrooklynWM!

  I definitely want my iPad to stay connected to the Wi - Fi connection while I use it.  Thanks for posting that other iOS and OS X devices have no problem with the connectivity dropping.  We can try a few things.

  Would first go through the steps listed in this article: If your iPhone, iPad or iPod touch connects to a Wi-Fi - Apple Support Network

  Then if it does not help, you can check network settings with this: recommended for the WiFi routers and access - points Apple supported

  After trying those, if you still see the drop connectivity, make sure the iPad Pro is updated with iOS 9.3.2 and check to see if the connection when you are in a certain place, time, or one event happening elsewhere in the House.

  Best regards.

• Can not access the site Web of John Lewis, get message server unexpectedly dropped the connection all the time

  Use the iMac with El Capitan 10.11.1 & Safari 9.0.1

  During the last week, I was unable to access the site Web of John Lewis and the message "Safari cannot open page www.johnlewis.com because the server dropped the connection unexpectedly. Sometimes this happens when the server is busy. Wait a few minutes and then try again"I retry but get the same message all the time. Can access all other sites ok.

  I emptied the cache, deleted the cookies and history. Enter the name of the site in its entirety is not helped either.

  Unable to access the Web by John Lewis site with my iPad either.

  Help!

  Try restarting/resetting the router.

  Try a reboot.

  Make a backup using Time Machine or a cloning program, to ensure that data files can be recovered. Two backups are better than one.

  Try to set up another admin user account to see if the same problem persists. If back to my Mac is enabled in system preferences, the guest account will not work. The intention is to see if it is specific to an account or a system wide problem. This account can be deleted later.

  Isolate a problem by using a different user account

  If the problem is still there, try to start safe mode using your usual account.  Disconnect all devices except those necessary for the test. Shut down the computer and then put it up after a 10 second wait. Immediately after hearing the startup chime, hold down the SHIFT key and continue to hold it until the gray Apple icon and a progress bar appear. Startup is considerably slower than normal. This will reset some caches, forces a check for directory and disables all start-up and connection, among other things. When you restart normally, the initial restart may be slower than normal. If the system is operating normally, there may be 3rd party applications that pose a problem. Try to delete/disable the third-party applications after a reboot using the UN-Installer. For each disable/remove, you need to restart if you do them all at once.

  Safe mode - on El Capitan

  Start Mode without failure-El Capitan.

• Unable to connect any device bluetooth on my windows vista, go to bluetooth devices but the drop down menu will not drop

  Original title: mouse bluetooyh
  Unable to connect any bluetooth devices on my computer windows vista, go to bluetooth devices but the drop down menu will not drop iam so unable to connect any bluetooth. any suggestions

  Hello

  read these tutorials on how to set up bluetooth

  http://www.vista4beginners.com/how-to-setup-a-Bluetooth-connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Bluetooth-enabled-device

  Here are solutions to some common problems with Bluetooth devices.

  You can also try a convenience store for diagnose and fix common problems with equipment and devices running.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

  f the foregoing does not fix it contact the manufacturer of the device

• the magic mouse 2 loses connection

  My magic mouse 2 is loaded (88%) and connected via bluetooth to my macbook pro (late 2011, OS X El Capitan 10.11.4).) Sometimes it loses connection and after a short time reconnects, what should I do for him have always connected, I mean without capricious disconnections?

  Hello heide1,

  Thank you for using communities Support from Apple!

  I understand that your Magic Mouse 2 going through temporary disconnects and stops responding intermittently. We know that situations of this kind can be frustrating, but we are here to help.

  To begin troubleshooting, I suggest to read and work through the steps in the following article.

  Your mouse or your keyboard intermittently not responding

  Follow these steps if your mouse or your keyboard sometimes stops responding temporarily.

  Click or press a key

  • Click on the mouse or trackpad, or press a key on the keyboard to reconnect the device to the computer. It may take a while for the device to respond.

  Search for interference of signals

  • Wireless networks that operate on 2.4 GHz can cause interference. Move base stations of phone wireless, microwave ovens and other appliances of 2.4 GHz far your Mac if you suspect interference.
  • Keep devices wireless to 10 meters (30 feet) of your Mac.
  • Avoid putting metal objects between your wireless device and your Mac.

  If your Apple wireless mouse, keyboard or trackpad doesn't work as expected - Apple Support

  See you soon!

• WiFi loses connection intermittently and the erasure of the arp arranges

  This has been asked before many times, but none of the above worked for me so far.

  I have a MacBook Pro with El Capitan on it. From time to time, usually 5 to 10 minutes,

  my connection drops and I can browse the internet. As:

  4 bytes of 8.8.8.8: icmp_seq = 7646 ttl = 53 time = 13,091 ms

  64 bytes of 8.8.8.8: icmp_seq = 7647 ttl = 53 time = 17,035 ms

  64 bytes of 8.8.8.8: icmp_seq = 7648 ttl = 53 time = ms 13,716

  Request timeout for icmp_seq 7649

  Request timeout for icmp_seq 7650

  Request timeout for icmp_seq 7651

  Request timeout for icmp_seq 7652

  Request timeout for icmp_seq 7653

  Request timeout for icmp_seq 7654

  Shooting, then turn on the WiFi will fix the problem, but I tried to limit the problem

  and I discovered that deleting IP of the route in the arp table will also fix connectivity

  immediately:

  $ sudo arp d 192.168.0.1

  Request timeout for icmp_seq 7718

  Request timeout for icmp_seq 7719

  Request timeout for icmp_seq 7720

  64 bytes of 8.8.8.8: icmp_seq = 7721 ttl = 53 time = 10,947 ms

  64 bytes of 8.8.8.8: icmp_seq = 7722 ttl = time 53 = 11,966 ms

  64 bytes of 8.8.8.8: icmp_seq = 7723 ttl = 53 time = 12,576 ms

  64 bytes of 8.8.8.8: icmp_seq = 7724 ttl = time 53 = 11,058 ms

  64 bytes of 8.8.8.8: icmp_seq = 7725 ttl = 53 time = 15,173 ms

  Deactivation of unicast arp has NO had no effect either:

  $ sudo sysctl-w net.link.ether.inet.arp_unicast_lim = 0

  Notes:

  -J' have two MacBook Pro at home. Other works without problem.

  -My phone and other devices work also with the same router with no problems.

  -The problematic MacBook works with other WiFi networks without any problem.

  What could be the problem?

  Yes, clear arp fix it. Very familiar with it.

  I had this problem for 2 years and more than 2 or 3 MacBooks, on El Capitan, Yosemite, and Mavericks.   I Googled it every 1-2 years months.  I captured packets and tested several access points... The best fix so far... is the arp compensation, and I have the automated at the moment:

  in a terminal:

  While true; make sudo arp - da; sleep 2; fact

  When the window is open, every 2 seconds, my arp table gets undervalued... and if I lose connectivity, the maximum cut is 1 to 2 seconds.

  I noticed that in some places, I don't have the problem... its as if my laptop reacts badly to some other customers on the same WIFI network.  This question makes me crazy, and I can't imagine how was such years.  If I don't fix it manually, I find myself for 30-120 seconds every few minutes.

• Time Capsule loses connection to the internet every day

  I have a time Capsule airport of 5th generation TB 3 (802.11 AC, A1470).  For the past year, I lost the connection Wireless to the internet once a week or more.  In recent weeks, he has taken place more frequently and often now also 3 - 4 times / day.  During the internet cut, the light on the Time Capsule still green watch, but none of my devices are able to get to the wireless (3 iPhones, iPod Touch, iMac and 2 MacBook Air, Bose Speaker).   I can restore internet connectivity by cutting and then by restarting the power of the time Capsule.    All phones and computers are running the latest software updates.  Airport Time Capsule is running 7.7.3

  We do not know if you have a service provider problem, a problem of modem or a matter of Time Capsule.

  Provider number... check with your service provider to ask them if they are experiencing loss of momentary service due to new installations of equipment on their service. They will most certainly say that their service was perfect and the problem lies elsewhere, but it does not hurt to check.

  Modem question... If the modem loses its connection to the service from the provider, even just for a moment, then the Internet will go down and the time Capsule which landed.  Unfortunately, there is no easy way to test the modem.  All you can do is connect a computer directly to the modem for a few days and check the connection from time to time to see if it fell.

  If so, this indicates that you that you might have a problem with the son of Internet that come into your home to the wall outlet, if you do not want your provider to send a technician to check and test the line to come in your House.

  If the wiring checked out OK, then you may have a problem of modem and the modem will probably be replaced... regardless of his age. If the modem is more than 4-5 years old, then it really must be replaced at this point.

  If you have not replaced the Ethernet cable from the modem in a few years, it would be a great time to do this.  There are some modems that just don't get along well with Apple routers... Motorola 6121 SB, SB 6141 and SB 6183 come to mind.  What is the number and model of your modem?

  Matter of Time Capsule... If there is no connection drops during your modem 2-3 days 'test' with a computer connected directly to the modem, then the time Capsule becomes the suspect.  About everything you can do in this case is to reset the device back to the default and then put settings in place again to see if this will help the issue. If you don't want to do it... and you have an Apple Store close to home... you can take the time Capsule to them and make them run tests on the Time Capsule.

  As you can imagine, 99 times out of 100, no problem you will find when you take the Capsule in the Apple Store because the drops intermittent are by far the most difficult problem to resolve.

• WRT54G loses connection and will not let me connect again

  WIFI at home was great for 2 years, then every sudden in the last 2 weeks I lose my signal on my laptop and iPhone. Then, I can not find the signal, or if the device detects the signal it wont let me connect. He hears no even except my wep key, I get a message saying that I can't connect to the network. Usually, if I unplug my router and the modem I can connect and wifi takes about 24 hours or so I lost. Any help?

  Since you have already updated the firmware on your router, you reset your router and re-configured all the settings on your router? If this isn't the case, then press in and hold the reset for 30 seconds button... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link

  When you re - configure all your router settings, you must change some settings under part wireless router...

  Set the channel on your router 11-2, 462 GHz Wireless and that the broadcast of the SSID should be activate...

  Then click the sub-tab under Wireless 'Advance Wireless Settings' and change the tag to 75 interval... Change the Fragmentation threshold to 2304 change the RTS threshold to 2307... Click 'save settings '...

  Now let's see if you can locate your wireless network and try to connect...

• Could not get the connection w / router WRT54G

  I tried all the suggestions on getting the router to connect, but have had no success. All the lights are on, but as soon as I unplug the router to the computer, I drop the signal and reconnect again. I tried to connect to the routers web page and it says unable to connect. Anyone have any suggestions on how to fix this?

  Connect the Modem to the Internet Port Linksys router and then connect your computer to the router on the LAN Port No. 1...

  On your computer, click on start - RUN - CMD and click OK... In the hit command prompt window type "ipconfig" enter and note the default gateway IP, yet once in the command window prompt type "ping default gateway ip" and hit enter and check if you have all the answers, if yes, then you can connect to the router configuration page using the default IP address.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 (the Linksys router default IP) and press ENTER. Let the empty user name & password use admin lowercase...

  Once you connect to the router configuration page, you can make the changes on your router.

• HP x4000b mouse - lose connection every few minutes with the HP Envy 17

  I just got a laptop Envy windowns 8.1 and the bluetooth mouse HP x4000b. The mouse lose connection every few minutes, (no connection with the bluetooth in the computer)

  Do you think is the problem of the computer (bluetooth) or the mouse?

  Hi elistephanie,

  I regret that, after exchanges of the mouse, you always have this difficulty.

  As you did on the original mouse troubleshooting and switch the mouse makes no difference, I suggest contacting HP support for further assistance.

  Please call our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number Plan of the Technical Support site .

• a switch that is part of the battery will charge if it loses connectivity to the master?

  If I have 4 switches configured as a stack - where the StackWise ports are connected within 1 to 2, 2 to 3, 3 to 4 and 4-1. Switch1 is the master.

  If something were to break stack connectivity between 4 to 1 battery still works as switch 4 still has connectivity to control through 3 to 2 to 1.

  Below the output of reference-

  switch #show switch retail
  Switch/battery Mac address: 0023.34b3.5600
  Current H/W
  Switch # Mac address priority Version State role
  ----------------------------------------------------------
  * 1 master 0023.34b3.5600 15 0 loan
  0023.0543.aa00 member 2 14 0 loan
  3037.a6ca.2000 member 3 13 0 loan
  3037.a6ca.6900 Member 4 12 0 loan

  Battery nearby Status port
  # 1 Port 2 Port 1 Port 2 Port switch
  --------------------------------------------------------
  1 low ok 2 none
  2 ok Ok 3 1
  3 ok Ok 4 2
  4 bottom Ok No 3

  switch #.

  With this as the current state 2 reload automatically cause the 3 and 4 to charge because they lose connectivity to control completely or they will stay up as of the individual switches

  And same question again - switch 3 cause reloading will rise 4 to recharge automatically as he lost connectivity to control completely?

  I've seen this happen... so need to confirm if what is expected or we must check and solve another question that might have caused this!

  This is not the expected behavior. A member of the battery is disconnected does not cause other switches to restart. They work as individual switches.

  Cisco documentation:

  An active switch connected to a fully operational
  stack becomes member of the stack. It receives the functioning
  setting up the master of battery
  . When you disconnect a battery Member
  Uh, numbers and port switch
  numbers of the remaining members of the battery
  no change and the switches do not recharge.

  http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst3750/software/...

• Error message: the remote device or resource does not accept the detected connection

  I had this problem for months at this point. The common way with that I solve is to restore to a previous point. Once restored, but I can't stop or restart the PC without the same problem occurs. For this reason I only turn sleep mode and then the connection is working. But by mistake an update made me restart automatically and now I'm back to the previous question. I downloaded and saved a substantial amount of data from my last restore, so I was wondering if there is a practical solution to this problem?

  Original title: perfect connection, but can not use the web or programs that require connections

  Hello

  Thanks for posting your question on the Microsoft community.

  Who are you referring when you say, "web or programs that require connections"?

  It seems that your antivirus software is blocking the connection internet or computer is infected with a malware or a virus.

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Run the network troubleshooter

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  If this does not help, then use method 2.

  Method 2:

  You can disable your antivirus and check if it helps.

  Reference:

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows/disable-antivirus-software#1TC=Windows-7

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  If the problem persists, use method 3.

  Method 3:

  I also suggest you use Microsoft security to check the virus or malware scanner.

  Refer to this article:

  Microsoft safety scanner

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Lose connection Wireless at some site but when work around the site router works

  Original title: Wireless problems

  When I am connected to my wireless router, some sites such as who's who, I lose the internet connection. He said SSL issues.or CE NE MAY NOT BE THE SITE YOU ARE looking for "but when I bypass the router, the problem goes away. There are other laptop on the router there is NO problem. What can I do?

  Hello Dennis,.

  I'm sorry that you have a problem trying to connect to some Web sites.

  Just to make sure I understand your question, you lose the internet connection only to some Web sites, but if you unplug your router, you are able to connect to the website like Facebook without problem.

  Let's start with the basics on the wireless connection.
  -Make sure that the cables are properly connected to the router.
  -Restart your router, turn it off for 45 seconds and then turn it back on
  -Try again to connect to the problem site.
  -Update your drivers for your network card wireless

  Then I'd suggest that you update the firmware on your router. Go to the router manufacturer's website and download the latest version of the software package.

  Here is some information on the use of networks wireless that might be useful:
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  If you still encounter a problem after trying the steps, answering the post again and I'll be happy to work with you for additional options.

  Sincerely,

  Marilyn

• IE9 "the remote device or resource does not accept the connection.

  IE9, "the remote device or resource does not accept the connection" appears when you try to open any website. My office to tell me that it is connected but cannot access any www. Meanwhile, my laptop connects fine. I have reset the settings in the internet options does not. I downloaded 'team' to connect (or similar) and asked for a connection and I thought that suspicious so uninstall this program... leaving me without access to the internet... * sigh * please can someone help me?

  Hello

  
  Method 1:
   
  Step 1:
   
  Run the network troubleshooter and see if that diagnoses the problem.
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
   
  Step 2:
   
  Reference:
   
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  See also:
  How can I troubleshoot network card?
  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems
   
  Method 2:
   
  Temporarily disable antivirus programs and firewalls.

  Disable the anti-virus software

  
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Windows Firewall
  http://Windows.Microsoft.com/en-us/Windows7/products/features/Windows-Firewall

  http://Windows.Microsoft.com/en-us/Windows7/firewall-frequently-asked-questions

  Note: make sure that you enable the antivirus software, other security and firewall after the test programs.

  Warning:
  Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

   
  Display the results.

• Can someone help me please? I bought Photoshop elements 13 and were not able to install it on my computer.  I made attempts at veveral to install it and I lose connection every time.  Since I was on a package of data plan with at & t, I buy e data

  Can someone help me please? I bought Photoshop elements 13 and were not able to install it on my computer.  I made attempts at veveral to install it and I lose connection every time.  Since I was on a package of data plan with at & t, I have buy the data each month.  I consume ALL my data.  To be a better way. Can someone help me please? I bought Photoshop elements 13 and were not able to install it on my computer.  I made attempts at veveral to install it and I lose connection every time.  Since I was on a package of data plan with at & t, I have buy the data each month.  I consume ALL my data.  To be a better way.

  I am well aware I could you bought the disc version. I bought the software Officemax in Vicksburg, MS I thought that the disc was included in the box.