Z3200ps: Ink system purging units?

Similar Questions

• Ink system failure Officejet 6500 (no error code specified)

  Ink system failure Officejet 6500 (no error code specified)

  I have turned off the machine on again (and it doesn't)

  I turned off the computer and unplug the unit (and it does not fix it)

  Without specific error code I'm not sure what to do

  Hi CHCA. Your Officejet 6500 must be out of warranty? You can doublecheck the warranty status of your printer here: http://h10025.www1.hp.com/ewfrf/wc/weInput?cc=ie & lc = on -if it is still under warranty, you should not pay for a new printheaad.

  But if your printer is no longer under warranty, you buy one a. The part that you really need to order an Officejet 6500, is CN643A. If you are in the United States, here are the HP part store page where you can order the new print head Assembly: http://h20141.www2.hp.com/HPPARTS/Search_Results.aspx?mscssid=C580393F30964EDD82B16A5C641BEC41 & Searchin' PartNumber = & SearchPN = CN643A

  If you are not in the United States, start from this page: http://welcome.hp.com/country/us/en/wwhowtobuy.html , specify your country and search for CN643A.

  Also, here is a support document that should help you with the replacement of the print head: http://support.hp.com/us-en/document/c01643079

  I work with HP but my messages and responses are mine.

• Printer ink system failure message all-in-one HP 6180

  I can't print because of the error message following on my all-in-one HP 6180 printer screen:

  Ink system failure. Refer to the documentation of the printer Oxc18a0201. I followed all the recommendations on documentation of the printer, such as: installation later HP updates, turn off the printer and remove the power cord, remove all the ink cartridges and then putting back in when prompted. Also, I rebooted my computer. None of these recommendations have worked. I need help! Thank you.

  Hello Kah524,

  I met your questions and we have a solution for this and you can try it, but that would apply only on starting with '0xC18A' and not '0xc19a error codes.

  Try the following steps for Photosmart C7280:

  A. - Press and hold the "*" key.

  B. - Press the "#" and release both buttons.

  Display should say "enter special key Combo".

  C. - Press and release in sequence the buttons '1', '2' and '3 '.

  Display should say "Support" and display the FW rev (something like R0631R)

  Press and release the right arrow button until the display shows "Menu of the System Configuration'.

  Press and release the OK"" button.

  Display should say "hardware failure status. If it isn't there already, arrow above for "Hardware failure status"

  Press and release the OK"" button.

  Display should say "hardware failure status: clear." Press OK to erase.

  Press and release the OK"" button. Message becomes "hardware failure (breakdowns) resolved state. Press Cancel to continue.

  Press and release the "CANCEL" button as many times as necessary, so that, either the "Welcome to Photosmart Express" screen appears, or, the 'ink system failure' is displayed. DON'T TRY TO PRINT AT THIS STAGE.

  Using the power button, turn the power off and unplug the power cable from the back of the printer output and the wall.

  Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first, and then to the back of the printer

  Switch on the device. The printer may display message "USE POWER BUTTON CLOSING the PRINTER" followed by "Press OK TO CONTINUE". Press OK.

  If the printer has already initialized, then go to the next step. If this isn't the case, the printer will start the "ONE TIME INK initialization PROCESS". Allow this process to do and not to interrupt. Once the initialization is completed, the printer print a Diagnostic page.

  To check, features of the printer print a PAGE of TEST car. If SELF TEST prints, then printer is ready for use or installation of the software.

  If the error is still there, or reoccurs replace the unit.

  --------------------------------------------------​---

  0XC19a error messages, the printer can be retrieved.

  Good luck and if that fixes the problem please click on Bravo...

  ---------------------------------

  Although I am an employee of HP, I speak for me.

• HP Officejet 6600 e-all-in-one printer - H711a/H711g 'Ink system failure', will not print computer

  At first, it was just a problem with do not print from the computer.  Error messages had to do with the failure of the print head or do not find print head, etc..  After going through several different controls online, download the scans, etc., it does not at all, print showing an error message "ink system failure".  I tried to remove and reinsert the 4 printheads (black 932, 933 colors) and turning market and check the caps and unplug the power.  Since this is a wireless network, I can't unplug the USB.  It was the OK signal.  Now, with this error message, I don't see the home screen printer controls.  It just says: put it on and then contact HP.  Help, please.  Very frustrated (it didn't happen all at once - a first he wouldn't print from the computer sometimes, other times.)

  Wildrat58,

  If you get ink system failure and you've been through the steps that are listed in the article above the printer may require troubleshooting. You can reach support - 800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number. http://www.hp.com/cgi-bin/hpsupport/index.pl - for the maintenance options.

  Good luck!

• Failure ink system - error 0xc18a0206

  I have a HP PhotoSmart C7250 all-in-one that has the error:

  Ink system failure

  Ink system has failed.  Cannot copy, receive faxes. or print.  Refer to the printer documentation.  Error 0xc18a0206. Stop the power, then on again.

  I was not able to locate this error in any manual or on the website of HP.  I found similar ones involving different printers and cartridges.

  I tried several scenarios to powering off the printer, unplug the power and remove the cartridges, but nothing works.  I noticed that the cartridges have dates that are in the past.  Before you go out and buy a new set of ink cartridges, I would like to know if this is a possible solution to the problem.  They are all new (just open the packaging) but more than one year after the date on them.  I don't want to buy a complete set of cartridges, so I'll have to replace the printer (who knows what cartridges will take a new printer).  After all, the cost of the cartridges, it would be a good part of the cost of a new unit.

  Hello!

  A few months back, I did a collection of solution for this problem. He helped resolved much ink system failures up to that date. You can check it out.

  http://www.out-of-warranty.com/ink-system-failure-error-0xc18a-HP/

• OfficeJet 6500 E709n: Failure of 6500 all in one ink system

  Recently inherited a 6500 all in one and installed this AM.

  Everything was going fine until I had to print a test page.

  Error: Ink system failure.

  The manual says disconnect power and reconnect after 10 seconds.  This did not help.

  When I ask to print, it says printing the error message and then it makes a grinding noise - in that order.

  Then an error message appears on my pc computer screen.

  This printer has been moved from one House to the other - it would have something to do with the message or the squeaking noise?

  Any suggestions?

  Thank you for your suggestions.

  I had 2 problems: ink system failure and grinding.

  The solution you provided workd partially - that is to say, I can print now but...

  First of all, concerning the failure of the system of ink - the operating manual supplied with the machine to stop the machine, unplug from wall, waiit 10 sec and reconnect.

  I tried and it doesn't work.

  The ground ' n you provided (from HP for the SAME model as my machine) gave another way to reset the machine - turning machine on, unplug the machine, unplug the unit from wall, wait 15 sec, wall plug, machine to reconnect.  In that order.

  Similar, yet very different and IT WORKED.

  So thanks for that.

  But the machine still makes a grinding noise that lasts about 3 seconds.

  I press print, paper flow, paper comes out of the printer, and then there's grinding hard.

  Back then a series of sounds as if something has been reset.

  All very very different from my previous 960C that is turned on when I printed and do not grind or reset of sounds.

  Clues?

• '0xc19a0042, ink system failure' on HP Photosmart B209a-m

  Printer: HP Photosmart B209a-m

  Computer: HP Vista

  I followed all the directions for turning printer works; turn off, unplug, plug in the unit, then by restarting. Restarted the computer. Always got message for ink system failure. What to do next?

  Thank you!

  For the failures of the system of ink and 0 x type codes, please see the document located here.

  Hope this helps, Taffycat.

• Ink system failure error 0xc18a0201

  After installing new ink cartridges provided with HP C7280 all in one ink system failure error 0xc18a0201 occurred.  Cannot find reference to this anywhere error code.  What is this and how can I fix it?

  I found this solution for... C5180 ink system failure, and assumed/hoped the firmware was the same... it worked!

  ***********************************************

  Press and hold the "left arrow" key

  Press the "Setup" key and release both keys.

  Display should say "enter special key Combo".

  Press and release the OK"" button.

  1. press and release the right arrow button until the display shows "Menu of theSystem Configuration'.

  2. press and release the OK"" button.

  3. the display should say "hardware failure status". If it isn't there already, arrow above for "Hardware failure status"

  4. press and release the OK"" button.

  5. display should say "hardware failure status: clear." Press OK to Erase".»

  6. press and release the OK"" button. Message becomes " failure State material (breakdowns) resolved." Press Cancel to continue.

  7. press and release the "CANCEL" button as many times as necessary, so that, either the "Welcome to Photosmart Express" screen appears, or, the " failureof the System ink " appears. DON'T TRY TO PRINT AT THIS STAGE.

  8. using the power button, turn the power off and unplug the power cable from the back of the printer output and the wall.

  9. wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first, and then to the back of the printer

  10. turn on the device. The printer may display message "USE POWER BUTTON CLOSING the PRINTER" followed by "Press OK TO CONTINUE". Press OK.

  11. If the printer has already initialized, then go to the next step. If this is not the case, the printer will start the "ONE TIME INK PROCESS of INITIALIZATION". Allow this process to do and not to interrupt. Once the initialization is completed, the printer print a Diagnostic page.

  12. to verify printer functionality print a PAGE of TEST car. If SELF TEST prints, then printer is ready for use.

  NOTE: If the error is still there, or reoccurs replace the unit.

• HP Officejet 6600: problem with the printer or ink system

  I have a HP Officejet 6600. I replaced the black cartridge with a new HP black ink cartridge. This message keeps poping up, there is a problem with the printer or ink system. Turn the printer off, then on. If the problem persists, contact HP. It gives me as two solutions. Solution 1: Reset the product. Turn the product off, and then unplug the power cord. Plug in the power cord and then press the key to activate the product. I've done this three times. Second solution: contact HP support note the error code provided in the email (I looked and it does not give me one) then he says, supported to contact Hp. go to: www.hp.com/support. Needless to say that this message keeps appearing on the screen of the printer and I can't do anything with the printer. Can anyone help with an idea? Please, I beg you.

  Hey @popcorn101,

  Welcome to the Forums of HP Support!

  I understand that you get the error "printer failure: there is a problem with the printer or ink system' on the front panel of your HP Officejet 6600 e-all-in-one printer.". Thanks for the troubleshooting steps that you received before reaching out for support, including. Right now, you have completed all the troubleshooting steps available in your efforts to solve this error in accordance with the document of support here. The failure itself is probably due to a failure of the print head. The print head is the part that the cartridges will fit. It controls the "reading" of the cartridges and put the ink on the page. If the print head does not, then the printing within your product system has failed. In this model of printer print head is a non-replaceable. Therefore, the resolution is a replacement of the entire unit.

  I highly recommend at this stage that you contact our Technical Support telephone queue for discover hardware replacement options.

  HP technical support are available by clicking on the following link:

  Contact HP support

  (1) once the page opens, please select the country in which you are located. Then, enter your HP model number on the right.

  (2) choose the 'Contact Support' tab at the top and scroll down to the bottom of the page "HP Support - contact" to fill out the form with your details.

  (3) Once finished, click on the 'Show the Options' icon in the lower right.

  (4) Finally, scroll to the bottom of the page and select 'phone number.' A file number and telephone number will now fill for you.

  I wish you good luck going forward with this!

• My HP printer has an ink system failure, what can I do to fix this?

  Hello

  I'll do a tutorial on how to solve the error message ink system failure.

  Now, in general this error can occur when the ink cartridges are bad, the printhead is damaged or the sensors are indicating that the ink system has failed to the printer.

  

  Step 1:

  The first step we take with an ink system failure problem is a hard reset with the printer. A hard reset Resets the sensors inside the unit causing the sensors reading if the print head or ink cartridges are healthy or not.

  Hard Reset:

  Unplug the power cord from the printer and the wall

  Wait for 30 seconds

  Plug the power cord into the printer, and then on the wall (do not plug power cord into a surge protector)

  
  Step 2:

  Now, if the hard reset doesn't fix the problem there are a few available documents to follow which will guide you through a few steps to try to resolve the printer.

  I will list a couple of them here:

  If your printer does not appear please go to HP support and drivers and search for your printer and your document.

  Photosmart C7280

  OfficeJet Pro 8600

  OfficeJet 6500 Wireless

  Step 3:

  If none of these documents allows to solve the issue, I would call HP @8004746836. They should be able to help you replace or repair the unit. This could result in the replacement of the printhead, if so please be aware that if you are out of warranty, it will cost you.

  Remember if you find one of my post useful or want to say thanks don't forget to click the White Star under my name to give me congratulations.
  I really appreciate it!

  Thank you!

  I hope it's useful!

  Remember if you find one of my post useful or want to say thanks don't forget to click the White Star under my name to give me congratulations.
  I really appreciate it!

  Thank you!

• OfficeJet 8600: HP OfficeJet 8600 'problem with the printer or ink system '.

  We have replaced the cartridges (with HP) and now we can print only about 1/2 a page, sometimes 1 page-, then it displays an error, "There is a problem with the printer or the ink system" and the printer should be set and to continue...

  We bought new (2nd series) of the ink cartridges and the same behavior exists.

  It seems to point to a new print head - but those who are more expensive than a new printer.

  Are there other measures I could take to try to resovle?

  I can't find scraps of paper (ie: torn, jam, etc.), nor any excessive ink any where - everything seems pretty clean.

  I removed the print head and cleaned the contacts.  I cleaned the contacts on the ink cartridges. I ran "Clean print head" in the Tools menu (which results in the same error)

  

  There are sometimes up to 3 of these messages "stacked."

  It is died regardless of what was asked of it... ie: print from netowrk, printing via usb, copy color, copy b & w, etc..

  Hello @jassing,

  Thanks for posting in the Forum from HP Support.

  I understand that you are experiencing a recurring error state in your HP Officejet Pro 8600 e-all-in-one printer.  I want to help you with this.  While it is clear that you have tried most of the recommended troubleshooting steps, I have some additional suggestions that might help.

  HP article presents common troubleshooting steps in order.  You can give these another shot before trying the more intensive step that I have in mind.

  If you have tried all of the above and your problem persists, click here to check the status of your printer warranty.  If your printer is currently under warranty, please call our technical support in 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  If your printer is NOT IN WARRANTY, try the following:

  Get ready to clean the print head

• OfficeJet pro 8620: officejet pro 8620, error: problem with ink system

  During the initialization of the printer, after that I inserted the ink cartridges, I get the error: "X-problem with ink system... I followed the directions: "lift the latch on the print carriage, reinstall the print head and then remove the cartridges and inspect leaks." Do not use cartridges that leaks. If the cartridges are OK, re - install. After you have reinstalled, turn the printer off and then back on. »

  Well it don't turn off the printer... I get another message: "the printer initialization and the ongoing calibration.» Do not put off the printer or turn off the power during this process. »

  I repeated this process on 6 or 7 times with the same result.

  I use "cartridges Setup" he claims.

  Help, please!

  Thanks in advance...!

  Johnny

  Hi @JohnnyLee,

  Welcome to the HP Forums!

  I understand that you found the error, the problem with ink on your HP Officejet pro 8620 system. I'm sorry to hear that, but happy to help!

  I recommend going through this guide, printers HP - "Problem with print head", "Printer failure", "Ink system failure", or "0 x." r "C2."... "Displays Message error.

  If the guide does not help, please call our hotline at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. Language-country selector.

  Good luck!

• OfficeJet 7500 has E910, "ink system failure".

  I have 2 Office jet 7500 a E910; I get 'ink system failure', the other works well; I take the printhead that is OK, I put it in the other: 'ink system failure '; I just got back from the other unit and no problem. I tried to unplug and reconect, same error. I tried to reset the printer, the same mistake; I cleaned with cleaning paper for lenses from contacts inside the print head holder, same error. What more is needed?

  Hey there!

  Thanks for getting back to me!

  I understand that the question much better now thank you for the clarification. So the problem is with the 1 printer, you take the printhead of the printer to work and put in the printer broke and he always says that there is a "ink system failure".

  These steps you have done certainly point to the printer in question. I highly recommend that you call Support technique Hp for help with this problem because they have more options for you I do. For a uniform 'ink system' on 1 unit you know has a printhead working in could be a clear sign of a fatal error.

  If you are in the Canada, U.S. dial 800-474-6836 or you can Contact HP worldwide.

  HP printers usually have a warranty of 1 year from the date of purchase, you can check the warranty using the following if you wish; guarantee cheque.

  I hope this helps. Please let me know the results. Have a wonderful day!

• Failure in the printer or ink systems

  What can I check after checking the unit ink and printhead on my printer IPSR 8600?  Get the error message 'problem with the printer or ink systems' have checdked ink cart. and print head.  All seem good.  Where should I go from here?

  Hello

  You have followed the steps in the link below.

  http://support.HP.com/us-en/document/c03096304

• I get the 0xc19a0042 ink system failure on my HP Photosmart B210 printer

  I followed the instructions for disassembly and cleaning the printhead twice, as well as to disconnect and reconnect and the 0xc19a0042 ink system failure message continues to show and I can't print or scan with my B210 printer. I now seek to replace the print head, but could not find the info on all the links from HP that I have searchded. Any help suggestions greatly appreciated.

  And if you are in the United States and want to order it from the hp online store: http://www.shopping.hp.com/en_US/home-office/-/search-Browse?SearchParameter=%26%40QueryTerm%3DPhotosmart%2BB210%2Bprinthead%26prodsubgrp%3DPrintheads&PageSize=15&SearchTerm=Photosmart+B210+printhead