ZTE phone open does not start after the 1.1 update

Similar Questions

• HP elitebook 2540p does not start after the successful bios update

  Hello people,

  I need your help.

  my hp elitebook 2540p with 2.5 "hhd does not start after a successful bios f.03 to f.24 upgrade done through windows 7.

  When I turn it on the blue light of wifi and power is on but nothing happen.

  I tried to remove the chip from the bios, cmos, hdd, ram, wifi battery... all, but nothing doesn't happen.

  I also tried to start it with the victory + b procedure and win + procedure four arrows so without USB key the caps lock flashing indefinitely but nothing happens, only the fan works quickly with a blue light

  with the USB the system restarts itself every two seconds and I have to remove the USB key.

  I do not know how...

  Thanks for any help.

  Luigi

  all very well now. I used the f.20 rom based on the internet and everything works again.

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• Windows 7 does not start after the installation of updates - sounds familiar!

  Apparently, I have another system that no longer starts after you install an update to Windows 7. New kick computer _ I have to disable the automatic update of windows. Twice I had to restore the system in the first week because he hung up after the installation of updates for windows 7. I have no idea what update is the cause of the problem.

  Essentially, start the screen goes black with the cursor blinking in the upper left corner of the screen. The only way out is to restore the system.

  Does anyone know what update is the culpret? HP support has no idea. Their only solution was to update windows 7 to 'never download an update from windows '. It is a terrible thing to be underestimated solution.

  Here's the resolution...

  I installed all the updates except KB2284742 954430, 973688 and 971033. So I decided to install these 1 4 at a time in the order shown. I installed successfully 228472 and 954430 and 973688 disappeared from the list of available updates. So I installed 971033 and it installed successfully and I was still able to restart.

  My conclusion is that there is a conflict between the first 3 updates when they are installed at the same time.

  Now my system is up to date with all windows updates and I'm able to restart without any problems!

  Close this message.

• ENVY M6 - 1184ca: 8.1 for Windows does not start after the installation of update KB2919355

  Updating Windows 8.1 KB2919355 has proved to be extremely problematic for me. When he was released at the beginning of 2014 that I was not able to get installed it with the exception of two occasions, the first being several months ago and the second time, a few days ago. I have constant pain to try to get the update of KB2919355 until recently. What finally got the update installed was opened as administrator command prompt and type the following commands,

  DISM/Online/Remove - Package PackageNameackage_for_KB2919355 ~ 31bf3856ad364e35 ~ amd64 ~ ~ 6.3.1.14 

  and then

  DISM / online/cleanup-image /startcomponentcleanup

  So now, the update of KB2919355 has been installed. Only one problem: like the first time I had the installed, Windows Update leave commissioning. As the HP splash screen that normally appears during the startup process appears after about 3 seconds, Windows displays an error Stop, and for a fraction of a second will display SYSTEM_THREAD_EXCEPTION_NOT_HANDLED error, which as I read, is related to the graphics drivers. The thing is, after the cancellation of the update (the computer in Mode safe start put Windows automatically uninstall the update and everything goes well after), then go in and uninstall the graphics driver, restart, reinstall the graphics driver and reboot again, and then reinstall the KB2919355 update, the problem recurs. I also tried to download and to install the new update of firmware for my particular DESIRE machine which was released a few days ago, but which has not helped either.

  I'm really stuck. I looked up and down, and I scoured Internet for anything that might help. I need to update KB2919355 be installed because without it, I can't book my free upgrade of Windows 10. This laptop is about 2 years and a half old now, so it fulfills all the prerequisites for Windows 10.

  Please do not suggest that I do a Refresh of the system or a system reset, as I have no way to back up my programs, that which some I would not be able to reinstall because I have more drives for some of my programs. Also, I can lose to save him for some of my games.

  When people ask me "What's up?", I always say 'the CAP '.

  So that seems to have solved the problem that is described in this post here. I followed the suggestion, which was to uninstall the driver, SPDT DuplexSecure (which has something to do with the SCSI devices, I'm not quite sure) using the SPDTinst (download here) and now it seems that Windows has started without crashing after installing the update KB2919355. I'll check my Windows Update history and see if it is there.

  Low and behold, a year to be really behind value is ultimately more. I have successfully obtained the update of KB2919355 works on my computer.

• computer does not start after the installation of updates

  Just click on the button "installs the update and the computer shuts down."  When the computer turns off automatically, I pushed the power button and now it is frozen the computer in start mode.  What should I do now?  Can I power off and try again (or which will mess up the configuration of the update that he just installed.

  Note: There are 21 updates installed last night without problem; then 1 update again (that set up correctly when I restarted this morning).  After a successful this morning launch, I noticed there was an another update to install, which is what made me at this point.

  Single computer at home (I use my work computer to submit this application).

  Wait awhile and see if, during the initialization of the problem to be solved or not. It is NOT a good idea to unplug the laptop.

  If this does not work, then try to press F8 and choose last known good configration, but you may need to reinstall the update again.

• Windows does not start after the most recent update

  I have 64 bit Vista and Office 2007. There was a group of updates for the latter in February 2011. Something in here is stop Windows at the login screen. Workes mouse and keys stick, but it won't take me to the password screen. Only way to get around it was to go in safe mode and do a system restore to remove the updates. Any suggestions?

  Applications, (Norton and McAfee) are notorious for not not upgrade (or uninstalling) itself.

  [You may want to print these instructions for reference offline. If a step said to reboot, reboot.]

  1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  2. close all open applications (that is, anything with an icon on the taskbar).

  3. After completing some you have a copy of your handy product key, uninstall all Norton software (including LiveUpdate and everything Norton Add ons) via Control Panel | Programs | Uninstall a program (or Control Panel |) Programs and features, if you are using the classic view).

  4 IMPORTANT! -Online activate Windows Firewall immediately after the restart.

  NB: Now you're "working without a net": no to ANYTHING else online (e.g., navigation, reading e-mail, chat) until you have completed step #7 below!

  5. right click on the file that you saved in step #1 above, and then select run as administrator.  DO TAP not your keyboard until the race ends, then restart.

  6. do a clean install of Norton 360 2011 (using your product ID, if need be) & reboot. CF. http://www.symantec.com/norton/support/kb/web_view.jsp?wv_type=public_web&docurl=20080514162318EN

  NOTE: Do NOT activate or install additional modules of Norton (for example, Norton Anti-Phishing) immediately.

  7. manually and repeatedly run LiveUpdate (Norton) until you get a prompt "no update more".

  8 reset the advanced settings of the IE by http://windows.microsoft.com/en-US/windows7/Reset-Internet-Explorer-settings

  9. open Internet Explorer (32-bit) only to http://support.microsoft.com/kb/971058 [ignore APPLIES to section] & run it in DEFAULT and modes difficulty then AGGRESSIVE. [1]

  10. restart once again & test.

  ~~~~~~~~~~~~~~~~~~~~~~~~
  [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not list the updates installed in Add/Remove Programs (Windows XP) or installed updates.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Reviews of Ubuntu does not start after the installation of updates

  I have a Windows 10 host and a guest Office Ubuntu 15.10. Ubuntu installs and runs fine until I have install updates, and then it gets so far through the boot sequence, but blocks trying to start the GUI.

  What should I do?

  Hello

  can confirm: after installing the last invited Ubuntu patches of the slaughtered 3.16.0-62 core during startup.

  Latest posts is: failed to start the vmware services.

  logfile VMware stops at the loading HGFS subsystem.

  To access the guest computer resolution: Boot with advanced options (hold SHIFT to start, until the menu loader grub is shown). Now select boot option (!) lower than 3.16.0 - 62.

  With 3.16.0 - 60, the guest operating system will start normally. Reinstallation or reconfiguration of the vmware tools don't fix this behavior. If something seems broken with kernel 3.16.0 - 62

  Any solution with core 3.16.0 - 62?

  Best wishes

• Satelite P300 does not start after the failed Bios Update

  Hello world

  I tried to update the bios of a P300 to this:
  18/03/10
  Update the BIOS
  Toshiba Windows 7-32 Bit 4.20 - WIN32 World Wide
  That I downloaded here: http://uk.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=UK after entering my laptops specs.

  The process flash hanged during the update and the laptop became screen starts, blank when turning on and nothing else...
  I tried to use the Phoenix of emergency crisis, created a diskette with the file Bios image that I downloaded but nothing succeeded.

  Access to the floppy drive USB floppy when you enter the recovery mode, I hear the beeps that indicate that a process is carried out, but when everything stops and restart... the problem remains.

  -Does anyone have a clue what to do next?
  -The warranty is void after a bios update attempt?

  Thank you for yor time.

  > - Someone at - it an idea what to do next?
  Well in this case, you will need to contact a local ASP (Toshiba authorized Service Provider).
  Guys could clean CMOS and flash the BIOS ROM module with a BIOS disk special crisis

  You will find here all the FSA all over the world:
  http://EU.computers.Toshiba-Europe.com-> support download &-> locate an authorized Service partner

• System does not start after the installation of update (10thFeb10)

  Updates to auto (windows Update) using.  Downloaded automatically update yesterday (10thFeb10) and when I shut my computer down it started to install them - as usuall.  However start my computer than this 11thFeb10 am and he began to run through regestry files when starting up.  Then it is impossible to load windows.  Just went to a blank screen.  Rebooted several times and were able to start it in safe mode.  Tried system restore but the same thing happens.  Obviously there was something to this update that 'changed' my computer and I'm not happy about it!  Also thought that there could be new updates (perhaps to fix the last update) but I can not even Windows Update to open it.  Tried online and he tells me that I have never downloaded updates and that none are available.

  I use Windows Vista Ultimate x 86.  I hope someone can help me!

  Got a response from Ms.  Good all who have this problem - you have an ATI Radeon graphics card?  Driver is causing the conflict.  Uninstall all the stuff ATI goes on ATI web site and install the download of 'single driver '.  Reboot and then you can download and install other fancy programs that come with your graphics card.

• Satellite A40-231 does not start after the incorrect firmware update

  Hello
  I have a toshiba satellite a40 - 231.it unbootable because I flashed it's drive(sdr-6112) dvd - rw with the wrong firmware and I also made a mistake in making a non bootable back active partition, try to Flash the correct firmware. So my question is: can I boot from the usb flash drive? I think it's the only option I have left, if not network startup.

  Thanks in advance!

  Hello

  As far as I know it of not possible to start other devices from the USB FDD / HDD / CD-ROM / LAN

  You can boot from network, but if you want to install the OS via the LAN you will need a RIS server. But it's not easy to do without any additional experience. So I think that this option isn't for you.

  It seems that the drive is dead or is malfunctioning and that is why the best idea is to replace the device's drive. I know, it's hard to hear that, but I don't see any other solution

• Satellite A100 does not start after the wrong Bios Update

  Yesterday, I upgraded my BIOS of 1.90 to 2.20 for VISTA... now, apparently, I downloaded the BIOS bad a100 to my A100 (PAAS...)

  Now the computer turn on (no display) then a few seconds later stops offshore and turns on again (without interruption), I am under warranty (and the computer is in the store) but I was wondering what to do if Toshiba is not honor the warranty?

  Thank you very much for your help!

  Hello

  I'm sorry to say, but it seems that you don't have the choice.
  You can ask him authorized partner in your country for the help that I know, BIOS update errors are not covered by a warranty and you will have to pay a small fee for fixing.

  In the worst cases, the motherboard must be replaced:(mais peut-être avez_vous une évasion chanceuse et seulement la puce ROM doit être flashée à nouveau)

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

  Original title: xp does not start after the installation of avira

  I have a HP Slimline s7410
  XP Home Edition SP3
  I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
  I have a cd/dvd drive of work.
  I don't have an XP bootable installation CD

  My system worked well until: I installed the free version of Avira

  Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
  I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

  Here's what my BSOD looks like:

  Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

  Any help is greatly appreciated! :)

  My first suggestion is to do a system restore at this time point.

  second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

  third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

  Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

  so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

  fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

• BlackBerry Z10 my BB Z10 does not start after the no shutdown reason cannot go home screan

  Dear expert

  pls help my problem

  My BB Z10 does not start after the no shutdown reason cannot go home screan

  How can I save my data and contact if I reload / back up the operating system how ever my phone cannot start and go home screan

  Thank you...

  Dear expert

  Thanks for your reply, but recognized link bb cant he showed a black berries knowledge so the transferdata button is impossible / cannot click. so I can't back up my files and data if I reloaded the OS. are there\s any idea/way of backing up my files if my phne was frozen?

  Thank you