Linksys Switches

Let's say that I have spend a routing 4 L3 VLAN VLAN 1 192.168.10.0/24, virtual interface of the switch is 192.168.10.254 inside this vlanVLAN 2 is 192.168.20.0/24, the virtual interface of the switch is 192.168.20.254 inside this vlanVLAN 3 is 192.1

I have two SRW2048. One in each building. I am running 2VLANS on both. I start to run in the time lag between the switches. How can I set up a bridge between them. I put 2 CAT5E cables between them. Is there a way to stick them together. How do I set

So we have a little SGE2000P and several SRW208G more, and it was decided to use a GSM7312 for basic L3 functionality (price was among the main issues to be considered, we have found nothing else suited our needs of features in this range). We have j

Whenever I have reset my siwtch change, the date and time at: 17:00 December 31, 2099 The firmware is 1.0.4 I tried to use SNTP and time system, but doesn't seem to work. Whenever the switch loses power the time must be reset.

Hosts: I used this same switch 5 ports for awhile but removed that I is no longer necessary to share the connection. Now, I needed to reuse the switch. I connected the cable between the router and the swih e-NET and the port fire lighted up as expect

I need help setting up wet610n. I get an error 107. I can't set toward the top of the page. I have a 2wire 2701 modem/router for my main desk top. I'm trying to connect my directv and blue-ray player in the living room.  I have a linksys WRT160n rout

Hello world. I have a SFE2000 switch and I want to do the following: (1) setup 2 VLANS, one on the port 1 (172.20.73.x), the second on port 5 (172.20.74.x), the remaining ports on the default VLAN (172.20.72.x) (2) enable Layer 3 mode and have all th

I did some research on this and I'm getting mixed results.  I have 5 Configuration of VLAN, not including the native VLAN 1.  Vlan1 has 1 as untaggged and together the trunk port.  Him is excluded.  VLAN 100 has unidentified port defined on trunk and

Hi all I have a strange problem with this switch cause it starts well and I get the connections between the switch, the WRT56G, and my computers. But then after just 2-5 minutes of the switch restarts and flashes all is once again the lights and crea

In addition to all my switches Cisco Catalyst (successful), I have a bunch of Linksys SD205 unmanaged switches on my local network. I want to configure my network for VLANs, which means I have all my managed Cisco switches will change to a "Routing"

Just have a quick? to see what I was missing out on these switches.  I have 2 EMS 2000 and 2 SGE2010 and 2 switches EMS 2010 P that I work with and every time that I reboot, I seem to always return to the default settings with the exception of the St

I have a client with an installed SRW248G4.  We are unable to determine the IP address assigned to the switch and we need configure ports.  The client cannot find the cable from the console provided with the unit and I succumbed to find where I can b

Hi people, I was wondering if someone has their switch EZXS55W nearby and could check the power supply for a part number or something similar. If not could you tell me the output voltage and amps from the power adapter? My power supply got separated

I have a Linksys EZXS55W workgroup switch and I'm running a router in to him, and then plug it into another router.  But I don't know how it any help would be greatly appreciated.

I bought a SGE2010 and a SGE2000P passes.  I want to connect these two switches.  What I need to buy a mini-GBIC MGBT1 and connect that way, or can I use a switch on each switch port and connect them like that? Is the MGBT1 really just a module to co

I can control the parameters of my 10/100 s port workgroup switch, the same way I can connect my Lynksis router and change these settings? Thank you!

I have improved my passage to 1.2.2b firmware and now I can't use the webfrontend more. is there a way to downgrade the firmware to 1.2.1bss where can I get the older firmware? I have tried Linksys and Cisco, but there is only the last (1.2.2b). How

Hello support team, ICH möchte zwei SRW2016 procedures zwei oder drei Ports Ethernet hintereinander schalten um die Netzwerkleistung zwischen den beiden Switch zu pegel. Danke Tirona EDV

I have been using an EF4124 switch for several weeks with no problems. Today, one of the users cannot access the network. By inspecting the lights on the switch, I found the lights corresponding to the user who is having problems flashing regularly,