10.6.8 PowerMac G5 Mac wake after sleep

Similar Questions

• Black screen on Macbook - don't wake after sleep

  I have a model mid-2009 13 "Macbook Pro which is been updated for the last OS. For the last two weeks, I had problems make him wake up once he starts in mode 'sleep'. It seems not important whether she goes to sleep because of the closure of the lid or inactivity, and it seems not important to know if she was in mode 'sleep' for a few hours or just enter the mode 'sleep'. I try to wake up by pressing a button, and the screen remains black. I finally have to press and hold the power button until I hear it powering down and then press the power button to turn it back on. Can I get the nice message that said "you shut down your computer because of a problem" when it loads up.

  I know that the device is on when the screen is black because it makes the noise to stop when I am forced to stop it manually. And whenever he refuses to wake up from the black screen, there a lot of battery when it finally loads up after that I turned it off. If he pulled when he falls asleep, plug the charger when it does not react with the black screen does nothing no more. And this isn't a case of the lighting of the screen being turned all the way down - I've tried too, just to be sure.

  I'd appreciate really any suggestion or help, because I have no idea what to do. He just started to happen suddenly, and since he started it happens almost every time my computer will sleep, what is super frustrating. I don't have not download anything new or modifications to the right until it all started, and it started before I've updated to El Capitan and continued since then, so I really don't know what the deal is...

  If your Mac does not sleep or wake up when expected - Apple supports

• EliteBook 8740w wake after sleep

  Hi all

  I bought laptop HP EliteBook 8740w

  I have several problems...

  Thus,.

  Configuration:

  (i5-520M, 4 GB, 320 HARD drive ATI 7820 M)

  OS - preinstalled Windows 7 Prof 64 bit

  All windows updates and the latest drivers for the chipset, video and so forth have been installed.

  1. computer laptop doesn't wake up after the mode 'sleep', i.e. all coolers start working really hard and LEDs are burning bright, but leaves black screen (5, 10, and several minutes, but no progress)

  I assumed problem with the BIOS, I have BIOS F.03 28.04.2010 but worm real version is F.09

  I went to the HP support and downloaded the latest site.

  But I can't update BIOS!

  If I use HPQFlash.exe program, he said: "after the operating system restarts, BIOS will be updated", but after restarting the BIOS operating system has old version

  If I use the options - key USB system after formatting and copying files (I checked the files on the flush), but when I try to load OS from hard Ras (after restart of ESC, F9), I see error - this disc is not system drive has chosen another, or something like that

  I tried at least trees different readers RAS, and always had the same result.

  I even downloaded bios f.08 version, but the same situation too.

  So, I try to summarize the problems

  1. computer laptop is not wake up after fashion 'sleep'

  2. it is not able to update BIOS

  3. What's wrong with loading PC from a USB...

  Is any body could help me... pleeeeeeze

  To solve the problem with the sleep mode, need update Intel management engine complete

  I've downloaded firmware from here http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=4138087&prodNameId=4137878&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-85374-1

  waking up after sleep works now!

  BTW

  about boot from USB, I tested the USB hard disk - it worked properly...

  but the boot of steel hunting impossible...

  and the BIOS is not updated either...

• Photosmart C309g-m requires Mac restart after sleep

  Hello

  I use a new 24 "iMac running Snow Leopard (10.6.3 version) and an all new HP Photosmart Premium C309g-m and each time the Mac wakes up from sleep, or I change username, then the only way I can get the printer to work to restart the Mac. Both are related to the USB connection.

  I tried to install the following drivers:

  (1) the CD supplied with the printer.

  (2) the drivers for the C - 309 m

  (3) the latest version of drivers 11.0.0 dated 2010-02 to: software HP Photosmart full feature and drivers - Mac OS X v10.4, v10.5, and v10.6

  None of this changes anything.

  There is not much point in having a printer that requires a reboot to print so I would be very grateful if anyone has any suggestions - other than the printer back!

  Best regards

  Octantly

  Given that you have installed the software from the CD (meant for 10.5 and earlier only), it may have messed you up.  We will uninstall this way:

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt Cmd and click on uninstall
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Now run a software update.

  Then, remove and reinstall the printer in System Preferences, Print & Fax.

  You do not have the software now since Snow Leopard as well print & scan drivers built-in. scan from Preview apps or Image Capture. Scan from the front panel of the printer does not work yet.

• Re: Portege R700 not wake after sleep

  Hi all
  I just bought a R700 and the laptop doesn't wake up after going to sleep. I did a bios upgrade. I have all the power options to sleep to "never" at the present time and other options of hibernation which works very well.
  I'm a little worried because I have to make the software updates for sensitive equipment during a couple of them the R700 is stopped and I had to do a power of the force down.

  When he tries to get out, sleep, the screen remains blank and the on-ramps fan until takeoff speed and stays there until I have to force a shutdown.

  Any ideas?

  I uninstalled tempro when I searched a driver that he has not found any so searched manually updated and found a few. Waste of time and interefering.

  Hello

  Have you noticed this problem from the day or later after the installation of these updates?
  > I'm a little worried because I have to do software updates...
  No one forcing you to make updates. You need to install are updated Microsoft.
  If the system works well with the original recovery image Toshiba (factory settings) leaves.

  The only thing you should do is to optimize BONE and remove the stuff you don't need.

  Back to your question:
  Can you confirm that this problem occurs with the factory settings and without any installation of updates?

• ThinkPad S230u wake after sleep of TSRI since BIOS update

  I use S230u (processor i7, 8 GB of RAM, 500GB HDD + 24 GB SSD) with Windows 8 x 64 for half a year now and so far everything works perfectly.

  I IRST activated and when I put it in mode 'sleep', it automatically records the State of SSD after an hour. That has worked very well so far - I can put it to sleep for short periods and then get up instantly and if I put it to sleep because more it will record in SSD and not use battery - when I wake up, it's flashing red LED for a while and the system comes back online.

  However, this Friday, I installed the BIOS - update 1.57.1.57 to 1.61.1.61 update (at least according to the system update history).

  Since Friday when I try to wake him up, he does not work if sleep is longer than one hour (or almost) and that the State has been stored in SSD. The Red led continues to blink, but nothing happens - after 1-2 minutes, the system restarts and Windows loads again.

  I want to downgrade the BIOS and doublecheck that is the question - maybe it's another patch Windows or Lenovo, so I want to be sure.

  I have already located the driver BIOS (http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS032000) downloads and wonder if BIOS to check if this is the problem of decommissioning can break anything with my laptop?

  
  

• HP pavilion n 204 tx: unable to wake after sleep in window 10

  I downloaded windows 10 yesterday and everything seems to work properly. However, whenever I SLEEP my computer, it is supposed to go to mode "Eve" where a twitch of the mouse wakes you up there. He goes to sleep, but I can't wake up through any interaction with the mouse or the keyboard. The light is still on, indicating that the computer is in sleep, but I can't seem to wake up. I had to hold the power button to turn it on then and I'm sure it's terrible that my computer turns off does not correctly. Everything was fine while I had windows 8.

  Any help would be appreciated!

  Hello @deepak9758,

  Welcome to the Forums of HP Support!

  I understand that you are having a problem of sleep mode and that he wanted to help you!

  For starters, can you provide me with the product number of the laptop?  Here is a link that you can use that will help you find your model and product number:

  How can I find my model number or product number?

  In the meantime, try to review the next steps, posted by Member of the DanG82community:

  1. Download version 9 or 10 of the Intel Management Engine Interface (MEI) driver.
  2. Browse HP Software and Driver Downloads of the site (http://www8.hp.com/us/en/drivers.html) to find the latest driver approved for your model. Filtrer filter by version, select Microsoft Windows 8.1 on the menu drop-down. Find the download in the category 'Driver-Chipset' If a pilot of MEI with a version from 9 or 10 number is listed, download. [9.5.24.1790 version 1.5 M (http://ftp.hp.com/pub/softpaq/sp66001-66500/sp66228.exe) works for most models.]
  3. If a pilot of MEI with a version from 9 or 10 number is NOT listed, download the appropriate driver directly from Intel (https://downloadcenter.intel.com/search?keyword=intel+management+engine). [9.5.24.1790 version 1.5 M (https://downloadcenter.intel.com/download/23091/Intel-ME-9-Management-Engine-Driver-for-Intel-NUC) works for most models.]
  4. Download the Package troubleshooting tool Windows 10 "show or hide updates" (http://download.microsoft.com/download/F/2/2/F22D5FDB-59CD-4275-8C95-1BE17BF70B21/wushowhide.diagcab).
  5. Change the Windows Update Services automatic (delayed start) parameter to the manual.
  6. In Control Panel, select administrative tools, and open Services.
  7. Go to Windows Update and double-click it to view its properties.
  8. Click on stop to stop the service to run.
  9. Change the Startup Type to manual, and then click OK.
  10. Install version 9 or 10 of the Intel Management Engine Interface (MEI) driver. If you receive a warning dialog box about the replacement of a newer version of the software, accept it.
  11. NOTE: You don't need to uninstall version 11 before installing version 9 or 10. The presence of a version of the driver is required to 'upgrade' (or demote in this case).
  12. Run the Windows 10 Troubleshooting Package 'Show or hide updates' and hide the updates of the Intel Management Engine Interface (MEI) driver. (This will block your system automatically reinstall or display of updates for version 11 of the pilot).
  13. Change back the setting of Windows Update Services to manual automatic (delayed start).
  14. Restart your computer.
  15. Rejoice!  You can finally sleep and stop again.

  Source: Re: how to solve the problems of Post-Windows 10 upgrade on HP laptops

  Please post back with the results.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great weekend!

• DELL Inspiron N5110 does not stop and does not wake from sleep

  Hello.

  I have Dell Inspiron N5110, who cannot stop it in Windows 7 or Ubuntu Linux. Specifically, I started Ubuntu Live from CD to eliminate the possibility that the problem is in Windows 7. Stop in Ubuntu does not work either. This proves that the reason for not an application in Windows that remains suspended and does not allow the laptop to close.

  The laptop computer may not wake after sleep or either Hibernate.

  I tried all the solutions that advised you to all the other people in the forum who have the same problem.

  1. the laptop cannot stop mode safe either.

  2 may not stop even after clean boot Mode - all services disabled and all package disabled Startups.

  3. I haven't tried to change the Power Options Advanced "Allow hybrid sleep" - both WE "On AC Power" and "Battery operated" - no change.

  4. I tried to install the latest NVIDIA video drivers. This did not help either.

  5 running only on battery change nothing - not cannot always stop.

  6 race only on AC adapter without battery - still cannot stop.

  7. I tried to remove the AC adapter and the battery, and now the POWER button for 30 seconds to RESET the phone - did not work.

  ATTENTION: I have read your forums all day and has seen at least 10-15 reports on the same problem, and not a single case fixed.

  8. This is why I have not tried Flash the BIOS with the latest version - I have read other people who have tried and it didn't work either.

  9. I loaded the BIOS default settings (F9) - stop still can't.

  NOTE: Change something in the BIOS and getting out once caused the laptop to freeze and I had to power off by holding button for a longer time.

  10. I ran DELL Diagnostics menu Boot (F12 at startup) - no error found.

  11. I couldn't find IEEE 1394 adapter in Device Manager to change the power management settings.

  In fact, none of the suggestions that you can give to change something in Windows is logical because I already mentioned that stop in Ubuntu does not work or the other.

  The question seems to be either in BIOS or a hardware problem. But which component? This is the CD/DVD drive?

  It is a new laptop.

  Please advice how to proceed. If you know which component fails please tell me.

  Remove the keyboard and palmrest (dell guide shows you how) and you should see a small button battery. Remove it at least 10 seconds, then put back. Enter the BIOS and make sure that there is nothing weird was changed. It should work fine now. I had this work in Ubuntu 12.04 these last days with no problems.

• Crush the display flashes for 2-3 minutes after that mini mac wakes up from sleep

  Crush the display flashes for 2-3 minutes after that mini mac wakes up from sleep

  If you have another Thunderbolt cable, plug it into the unused port on the

  Thunderbolt Display and then in the Mini and see if the same thing happens.

  What you can see is a precursor of the poster, built out of the cable.

  At least, it could eliminate a costly repair problem.  Although the cable itself is not

  expensive, opening to the top of the screen of TB to replace could be.

  Well that not connected on a Mini, I began to see in similar behavior my

  iMac, so that there was finally a break in the complete cable.

• with 10.11.2, Mac Pro 2013 wakes up not 4 k shows up after sleep as before.

  I installed 10.11.2 today and found that the Mac Pro wakes up not 4 screens connected to the thunderbolt ports k. I tried many kinds of 4 k screens, including u28e590d, u24e590d, p2716q etc., but none of them is waking up after sleep. the only resolution is to disconnect and reconnect the thunderbolt (view port) cable a thunderbolt different port.

  these screens all work perfectly with 10.11 and 10.11.1.

  Steps to reproduce:

  1: having a Mac Pro 2013, configurations and install 10.11.2

  2: Connect a screen 4 k as u28e590d to the thunderbolt port, using mini-displayport cable.

  3: let the Mac Pro sleep

  4: when press a key or click the mouse, the Mac Pro will wake up but the screen won't wake up 4 k.

  everyone knows the same problem?

  Hello.

  same problems here :-(

  MacPro 2013 with the D300

  4 k screens: 28e590d Samsung and Asus PA328Q.

  Can someone help? This problem is very annoying!

  Andi, of the Germany.

• Fallout 3 stops working after the computer wakes from sleep

  Since the games for Windows Live 3 is out, Fallout 3 has never been the same. He used to work at best my GfWL and now her nightmare. Recently, after that I quit the game and put my computer to sleep, Fallout 3 will stop working completely after wake up. I try to start it and I get them all is a cursor with a small blue rotating light. What is even more strange, is that my computer goes into a State of semi who no longer meet this point where programs and keyboard shortcuts no longer work, but I can browse my hard drive. I try control + SHIFT + ESC to see what the devil but that causes Windows Explorer to stop working. CTRL + Alt + Delete does not work either. No matter what I try, once I start Fallout 3 after the computer wakes from sleep, I can't do the task to the top manager and I can't use my computer. The only way to get it is to hit the reset button or turn off manually. Can someone please help to get rid of this problem?

  Hi murphy449,

  1. did you of recent changes on the computer?

  2. the problem only happens when you start fallout 3 after the sleep mode?

  3. are you able to wake the computer quits successfully sleep mode?

  4. What is the version of Windows installed on the computer?

  Method 1

  I suggest that you manually download and install the latest drivers for display on the computer card and check if it works.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2

  If the previous step fails then I suggest that you try the clean boot procedure to check whether a third-party program installed on the computer is causing the problem.

  To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  If the previous step fails then I suggest you check the observer after return with details and events for the cause.

  What are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  What are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP 15r205tu: i3 5010u, uncore after sleep and wake up power consumption increases

  After start of the uncore cpu power remains unused 1W (according to the CPUID HWmon) below.

  If you sleep and wake up the laptop, then the uncore power increases to approx. 2W.

  Time remaining on the systray icon is touched by it.

  Navigation on the duration of use of a low-power battery is reduced after sleep wake cycle.

  Is this a known issue? Is there a solution?

  Thanks for the post and suggestions.

  Now, I know what has caused this problem.  I had turned off the network adapter cable into the Device Manager to save energy!

  This caused the uncore somehow to go crazy and pointing up (only after the day before). Now, I have activated the wired lan card and all is well. The laptop can be used for about 9 hours on battery power saving mode now sometimes the loading of web pages.

  Thanks again.

  PS: If any unused pci express port is disabled it can lead to the same behavior.

• Unable to wake up after sleep - HP pavilion DV6t - aiu55av - 9

  Unable to wake up after sleep - HP pavilion DV6t - aiu55av - 9

  tried on different keys-ctl alt - del - nothing works

  You can also view the latest BIOS update for your machine. Use the link at the top of this page-"Support & Drivers" - to find your support page templates.

• Windows 7 "no DNS (or no network) after sleep (wake up) sleep (or Hibernate).

  The purpose of this thread is to understand the expected behavior of the TCP in Windows 7 stack and the cards on the resume from sleep/hibernate - not - display the suggestions that have been posted in other threads.  I also wanted to gather some folklore on this subject in one place...

  It seems to be a group of people having this problem Windows 7 "no DNS (or no network) after sleep (wake up) sleep (or Hibernate)" without definitive duty (or with various) responds to what the issue is.

  Do some reading on this in various places, I see:

  -Suggestions to disable UPnP.  This should be largely irrelevant to the problem.

  -Reset the default router.  Generally, this should not be necessary.

  -Reinstall Windows 7 (ah yes, the panacea for all ills!).

  -Replace DHCP static IP address.  This should not be necessary (considered at best as a workaround).

  -If it solves the problem, it points the finger at DHCP feature / state on the curriculum vitae of sleep?

  -Disable the firewall.  This shouldn't be a problem (why would it).

  -If it is a question, it is likely to be isolated, rather than the majority of the cases.

  -VMWare (or similar) virtual networks.

  -This could be a problem for some people.  It would be useful for anyone who has a problem to confirm if they have VMWare or similar virtualization installed products (who can create virtual networks).

  -Disable the TCP (TCP sliding windows) tuning car.

  -It is possible that TCP auto tuning could be a problem for some people - but - unlikely, it would be a problem for people only on the recovery from sleep mode.  I think that anyone with questions about the TCP (TCP sliding windows) tuning car rather than questions on RESUME intermittent connectivity problems.

  -Some people report improved performance when turn it off this feature.   Report MSFT from 10 x to x 1000 in laboratory performance. conditions.  It's one you need to test yourself to see if it helps or otherwise.

  -NETSH INTERFACT TCP SET GLOBAL AUTOTUNING = OFF

  -NETSH INTERFACT TCP SET GLOBAL AUTOTUNING = NORMAL

  -It works on XP but not on Windows 7?

  -It is fairly widely commented that the TCP stack has been re-written/improved thanks to Vista and Windows 7.  It is not surprising, therefore that problems on Windows 7 that do not exist on Windows XP.  This does not necessarily imply that the Windows 7 stck is bug, just as not all software and peripheral food chain TCP are speaking the language of same/current (in the absence of a better technical description).

  -One wonders, therefore, are only optimizations issues additional tuning and unloading that have been made in the new stack TCP?   How this confrontation with the problems that occur only in the curriculum vitae of sleep/wake extended?

  -Some people recommended prevents the system from voltage of their cards during the standby/hibernation.  Does this means:

  -The card is not dynamic.

  -If the card is allowed to be turned off so there will be a lag between the state saved in Windows and the State represented (none) in the card when the system is out of his sleep (or Hibernate).

  -Perhaps, it's something that needs to be addressed in the functions of battery/sleep TCP in Windows 7 - How to handle/recover the situation when the NETWORK adapter is turned off?

  -If we put the system to sleep, we want to have power supplied to the maps or not (what are the implications)?

  -People have the same problem for the hibernation?

  -If there is a problem of State related to the cards, would be - why, in some cases of people solve the problem by disabling optimizations that involve some treatment being given cards instead of being carried out using the processors.  If it was kept in the processors, we have consistent state on the resume (as opposed to cards)?

  I think what I understand of MSFT is here:

  -What is the behavior designed in the stack revised to ensure a consistent state between the adapter, battery, previously obtained DNS, DHCP settings, etc., the curriculum vitae of sleep/wake extended.

  -Unlikely connections persist across sleep/hibernation - so are they remind/re-restored?

  -Windows 7 has more work to properly manage this for cards that - are - power off during sleep?

  -Is - it a requirement of MSFT at this time for an own CV, the card must stay lit?

  An exchange of views on how this is supposed to work for MSFT would be useful.  Then perhaps hundreds if not thousands of people facing this issue can understand why it happens and how they can solve.

  [upstairs]

  Thank you for spending time and energy on it. I had a frustrating to deal with this problem, but - finally, disable virtual network cards seems to have helped.

• I bought educational individual creative cloud on Mac, but after installing it still shows trial version on the soft CC.

  I bought educational individual creative cloud on Mac, but after installing it still shows trial version on the soft CC.  How to configure the version full?

  Hello

  Please visit:-https://helpx.adobe.com/manage-account-membership/cc-reverts-to-trial.html