2 meter 10GB cable - cooper or optical?

Similar Questions

• Driver for glucose meter connection cable

  Hello
  I use windows 7 for the first time and I can't get the pc to recognize my blood glucose meter. I have contacted the software vendor who suugested that some drivers and either they don't work or I'm unable to install them correctly. Everything worked fine on my old windows xp pc who died recently.
  I get notification...   Peripheral USB not recognized when I start investogate in the system, the error code only I can find is that windows has found the driver but disabled the device (code 43).

  The provider of the software gives the following information.
  Cable USB of Lifescan has a prolific inbuild, so you can use the prolific drivers as well.
  And as normally work Vista drivers also with Win 7, there should be no problem to install a vista driver prolific these these here for you connect meter with your PC: http://www.sidiary.org/download/driver/Sitecom%20cn116-Vista.zip

  Just to give more information, lead has a USB port on the computer end and a 2.5 mm Jack on the end of the computer. The meter is a one touch ultra lifescan
  I am an insulin dependent diabetic and now I have to go back to how the results were achieved 10 years previously, pen and paper. Windows 98 was better, medical stuff for me is much more important that the videos or games, please help if you can

  I use also the 64-bit Windows 7 Home premium, the old version of One touch no longer works, but they have a new online version and it works fine.

• SSD instead of an optical drive on the Pavilion dv6-6b56er

  Greetings!

  My laptop is Pavilion dv6-6b56er, model: A2Z12EA #ACB.

  I want to remove the optical drive and install the SSD.

  HWiNFO64 info:

  SATA host controller
  Interface supported speed: Gen3 6.0 Gbps

  It's SATA III. problem is my hard drive (tow model: SAMSUNG HM641JI) installed on SATA II.

  and optical drive SATA I. I need to find a cable connector to hard drive (with SATA III) and replace it with the cable from the optical drive.

  But I can not find

  info on the hard drive cable is so little:

  CASA 15 "HDD CABLE

  50.RI05.011

  ANPI P 10/11/13

  Spoiler (Highlight to read)

  

  That's all.

  If you know the link or something else, you're welcome

  Greetings! solved my problem by buying optical Bay 12.7 mm

  Now I have SSD on SATA 6 Gbps gen3 and HDD - gen2, SATA 3 gb/s

• Are compatible cable SHC68-68-EP and SHC68-68-EPM cable?

  I use a DAQ card 6062E with a chassis SC-2345.
  For now, to connect with each other, I use a SHC68-68-EP of 2 meter long cable.
   
  Now I need a longer cable, this cable is only 2 metres but I need 5 meters.
   
  My question is: are SHC68-68-EP and compatible SHC68-68-EPM cable (for M-series cards)? (the EPM cable exists in versions 5 m and 10 m)
   
  Tips: 
  1. I downloaded the two support cables wiring diagrams OR. The only difference is: the new cable (EMP) for M-series cards, a PIN which was formerly assigned to GND is now separated into a new pair twisted and assigned to a signal (PFI 15 / P2.7).
  According to this, it seems that 'new' EPM cable can be used on other maps than M-series of retro-compatible way (but of course 'old' EP cables cannot be used on M-series cards because a single signal would be connected to the MASS).
   
   
  2. The SHC68-68-EP cable, I bought 3 weeks ago had a big label "NI SHC68-68-EPM" on his bag when I got it... Maybe OR ships 'new' EMP cables when order us EP cables 'old '?
   
   
  Does anyone have information about it all?

  Hi Fabrice,.

  It is possible to use the EPM cable with your E Series device. Changes to the MOU to create the EPM have no negative effect when used with the E series devices.

  The main difference between the two cables is the assignment of pins for PFI 15 (as you said). Cable EPM has also been optimized for digital extra lines on M Series devices to minimize noise and crosstalk on the PFI lines.

  Let me know if you have any other questions.

• Pavilion slimline s5660f digital audio

  I am trying to hook a digital audio connection for my sound 5.1 surround via fiber optics 6' / 1.8 m.  The problem I have is the plug that connects to my digital audio port on pc is too big.  Can someone tell me if there are cables to fibre optics different meter size and if so what size I need for my pc model.  I can't find this info anywhere hp.com Specs for my computer.  Thank you... xx

  Yes, the fiber optic cable sockets are in different sizes. I know that the selection where I live is limited, but I am sure that you would have a hard time to find them if you look pretty hard.

  Mario

• Network problems? Download speeds low, even when the wired?

  Hello

  Recently, I upgraded my router to a router from Verizon to have a connection to 75/75.

  However, even when plugged in, my download speed reaches a maximum of 10. However, when you use other laptops, their speeds reach up to 40 or 50 close.

  Here are my specs.

  Operating system
  8.1 Windows 64-bit
  CENTRAL PROCESSING UNIT
  Intel Core i7 to 2.90 GHz 45 ° C
  HASWELL 22nm technology
  RAM
  16.0 GB Dual-Channel DDR3 @ 798 MHz (11-11-11-28)
  Motherboard
  Alienware 01W2J2 (U3E1)
  Graphics
  Monitor generic PnP (1920x1080@60Hz)
  4096MB ATI AMD Radeon R9 M290X (Dell) 56 ° c.
  4096MB ATI AMD Radeon R9 M290X (Dell) 70 ° C
  Disabled crossFire
  Storage
  WD10JPVX-75JC3T 931 GB (RAID)
  10GB SSDMCEAW080A4 m (RAID)
  Optical drives
  HL-DT-ST DVDRWBD CA40N
  Audio
  Realtek High Definition Audio

  What's wrong?

  What Alienware do you have?

  Some Broadcom drivers have a weird 'green' setting that holds the speed to 10. Check your driver settings (or clean-install a better). In addition, use cables Cat 5e or better and all ports should be 10/100 or gigabit.

• tvOS 10 update breaks DD5.1 on Apple TV output 4 HDMI

  Then, I upgraded tvOS 10 last night. Now, all the movies content on Netflix or iTunes won't play with audio when I output 5.1.

  I have my TV connected to a HDMI/optical splitter so that it can feed my Sonos Playbar. Prior to the update of the audio has been correctly be pulled the HDMI cable and divided optics 5.1 true, as stated in my application of parameters of Sonos. Since the update, I have to stereo to get all the sounds, which is so obviously not true 5.1.

  Someone else had this problem? Any ideas on a solution?

  Thank you.

  Try the Bike ATV power and sound systems. It is working for me with HDMI to TV and optical out to A / V receiver. It has no reason for the software of the ATV to make it different than before.

• TV Toshiba 40L3433DG - not coaxial audio work?

  Hello!
  I'm sorry for my sentence, but English is not my natural language

  I have a problem with a coaxial audio output in TV Toshiba 40L3433DG, which is connected to the home theater LG BH6530T via coaxial converter in French - output optical. Home Theater is not playing the sound of the television but detect a TV - input optical signal is active in home theater settings, after that disconnect the cable TV coaxial, optical entry into a home cinema is inactive. I tried to play sound from TV programs (DVB - C), video from a USB key connected to the TV and YouTube.

  I first thought that the problem is in the coax - optical converter, but I borrowed from my DVD player old parents with coaxial output, I connected the coaxial cable from TV to DVD and home theater has started playing the sound sent from the old DVD drive. In this way, I have eliminated the potential problems with the coaxial cable, converter cable to fiber optics and optical of entry into home theater.

  There's the television... Now my question - does this kind of TV has a special option to activate the digital audio output? In the sound settings, I can choose digital output PCM or compressed. If the TV does not have a special option to activate the output, is the possibility to use a test mode to check the coaxial?

  Posted by bambaja
  

  Hello!
  I'm sorry for my sentence, but English is not my natural language

  I have a problem with a coaxial audio output in TV Toshiba 40L3433DG, which is connected to the home theater LG BH6530T via coaxial converter in French - output optical. Home Theater is not playing the sound of the television but detect a TV - input optical signal is active in home theater settings, after that disconnect the cable TV coaxial, optical entry into a home cinema is inactive. I tried to play sound from TV programs (DVB - C), video from a USB key connected to the TV and YouTube.

  I first thought that the problem is in the coax - optical converter, but I borrowed from my DVD player old parents with coaxial output, I connected the coaxial cable from TV to DVD and home theater has started playing the sound sent from the old DVD drive. In this way, I have eliminated the potential problems with the coaxial cable, converter cable to fiber optics and optical of entry into home theater.

  There's the television... Now my question - does this kind of TV has a special option to activate the digital audio output? In the sound settings, I can choose digital output PCM or compressed. If the TV does not have a special option to activate the output, is the possibility to use a test mode to check the coaxial?

  Hello I have the same problem.
  My tv is 48l5435dg. I tried my Soundbar with a cheaper TV and works very well (so no problems cable or converter).
  I restarted my toshiba repeatedly and sometimes he started working, but just 2 seconds (it loses the signal)
  I don't understand what I have to do!
  All solutions?
  Thank you

• Re: TV Toshiba 46WH08G - no image using a DVD player through receiver

  I have a pioneer DVD PLAYER connected to my Yamaha reeceiver via video cables component and output digital optics.

  Image and sound via 46WH08G TV is very good - no problems.

  I recently bought a new AKAI DVD player to player USD movies.
  I connected the component video output cables and digital optical from the Pioneer to the Akai.
  The sound is perfect, but no image.

  Can someone explain why - it has to do with the scan type.
  Any help would be appreciated.

  Best regards

  Carl

  Hello

  It's a Toshiba laptop computer and accessories for laptop forum and I doubt that anyone would be able to provide some ideas on this theme.
  Ask you for help on some special HiFi forums recommend

• Qosmio F20-137: connection to Hi Fi

  I have attached my Hi Fi laptop using the headphone jack (headphone to phono cable) and the sound is pretty poor. Y at - it another way to to get a better result or will I have to buy Toshiba's own surround speakers to get a decent sound?

  Hello

  As far as I know the S/PDIF audio line is available on this unit.
  This release makes an excellent audio quality. You need a cable S/PDIF optical you can use into the S/PDIF (headphone) jack.

• Install a secondary hard drive

  I have a small form factor and want to install a second hard disk in the optical drive.

  The new Seagate drive came with all the SATA cables. and the optical drive cable usual additional split from him. One of these cards is part of the new drive, but one that goes to the motherboard is too short to reach the appropriate connector. Seems that I just need a very short extension, but when I do my shopping for one I'm overwhelmed by a mess of all sorts of types of plug SATA cables and cable whose pictures are not clear enough for me to recognize exactly what I need.
  
  Can someone advise me please I need re this plug on each end, as well as the extension of better quality? Guidance appreciated.
  
  Clueless in Cableland,
  Rob

  Hi, Rob:

  I don't know what you plug installed on the hard drive, but like I said if it was the biggest power supply sata plug, I think what you need is then the sata data cable.

  One with a female end straight to the motherboard and the other female 90 degrees on the hard drive.

  SATA cable speed ratings do not matter.  Just get one that will reach from the motherboard to the hard drive.

  

• Is it possible to route signals of relaxation between two chassis PXI-1002 with the PXI-8335?

  Hello

  as the subject says, I am interested in the delivery of a signal to trigger between two chassis PXI-1002. At present, these two chassis are connected by a MXI - 3 system using maps PXI-8335. The software is Labview 2010 sp1 and 380 NIScope drivers.

  We want to keep (a PXI-5122 by chassis) scanners supply separated due to the requirements of our measure! The chassis are connected via cable to fiber optic. This explains why I can not just use the shutter release in Star, or connect via 'Trigger' or 'clk' cards (the inputs / outputs to the front of the cards).

  I found a few examples, but they seem to all be designed for use with a chassis only, I'll call later to the examples that inspired me to this point. Each guide explaining the synchronization of several chassis systems seems to use another material or VI is not accesible to me. This makes me wonder if my hardware has the capacibilities I need.

  The first picture shows approximately where I started from (sorry I can't post VI, confidential...):

  Only the middle part is interesting. Two sessions are initialized and manipulated parallel, trigger too. This has led to delays in the signals and should now be fixed. This apart from the VI works fine.

  Goal is to trigger only on one channel but both devices! If possible, the device will trigger must be chooseable.

  I started to rebuild the VI using the "EX Synchronization.vi 5xxx niScope' seeming spontaneity. The result is shown in the following image:

  

  I tried different RTSI lines, but had no positive results. only the main channel has triggered.

  After this first approach, I looked in the "niScope EX .vi multi-Device configured Acquisition (TClk)" and other examples of TClk which seem to work for similar problems. The VI of reconstruction can be seen in the following images:

  

  (Sorry, I had to use two photos..)

  In this case, I didn't have no choice for trigger lines, it would automatically set the VI TClk. I tried to trigger on both devices, though. This second approach seemed promising to me, but it was an error:

  "niTClk Synchronize.vi:1".

  Index (starting at zero) of the session: 1

  The error reported by the pilot of the instrument:

  No registered trigger could be found between the
  devices on the route.

  If you have a PXI chassis, the chassis correctly identify in
  MAX and make sure that it has been configured correctly. If you use PCI
  devices, make sure they are connected with a RTSI cable and that the cable RTSI
  is saved to the MAX. Otherwise, make sure that there is an available trigger line
  the trigger bus shared between devices.

  Source device: PXI1Slot4

  Target unit: PXI2Slot4

  Status code:-89125niTClk Synchronize.vi:1

  Index (starting at zero) of the session: 1

  The error reported by the pilot of the instrument:

  No registered trigger could be found between the
  devices on the route.

  If you have a PXI chassis, the chassis correctly identify in
  MAX and make sure that it has been configured correctly. If you use PCI
  devices, make sure they are connected with a RTSI cable and that the cable RTSI
  is saved to the MAX. Otherwise, make sure that there is an available trigger line
  the trigger bus shared between devices.

  Source device: PXI1Slot4

  Target unit: PXI2Slot4

  "Status code:-89125"

  This error came back even after I've identified this drug as possible to the MAX, as shown in the screenshot:

  

  In some of the textbooks, they showed how to get the MAX trigger lines, but as you can see, there is only booking options in my MAX. Whatever I do, I can't find options to define how to get my trigger signals...

  In principle, it is possible to trigger instruments in different chassis, which is indicated in this Guide and others... the question that remains is can it be done with my set of components?

  I understand that the use of multichassis compromised the integrity of the lines very adjusted as trigger in Star etc., so the configuration should be taken into account in some way, that my approach does not, I knew... But there must be a way to do this? And to start: to get just any signal from one device to the other trigger!

  For any advice on this issue, I would be very thanfull!

  Concerning

  Max1744

  Hi Max,.

  Thanks for the detailed post and explanations of your application and requirements. You're right using TClk, because this is the optimal method to synchronize the 5122 digitizers. The original VI you worked with is unique for some of the legacy scanners and does not directly work with scanners based on the most recent CMS (for example the 5122). The good news is that you can synchronize these cards to separate chassis, but it will use the calendar 66xx and synchronization (T & S) cards in the chassis of the master and the slave, as indicated in the guide that you have accessed. These are needed because a common reference clock must be shared between them as well as a couple of tripping. MXI itself can not handle export triggers and clocks, so there is no way to do this without physically wiring between the chassis with cards T & S. Unfortunately, regardless of what specific method, you use for synchronization, it will take a material extra beyond what you currently have.

  As one of your needs looks like it is necessary to retain wiring between the chassis directly, you may need to consider to synchronize using 1588 or GPS protocols. 1588 Protocol is a system for synchronization on the network while GPS course use antennas and locks for a common wireless signal. Although these synchronization methods may allow you to keep your chassis isolated, they will also require some manual configuration because you would be able to use the TClk synchronization and so the level of synchronization you can get between the cards may not be as good that can physically wire signals between the chassis using T & S cards.

  Hope this helps,

• HP touchsmart iq506 vista 64-bit

  receive blue stop screen, xoooooo7e and iastor.sys address f8 boot in SafeMode white bar informs you that windows is loading files, then past to screen showing windows loading bar, bar moves from left to right and nothing else happens no matter how long wait, also system f11 recovery did shows all the files on the screen at the bottom of the screen and loading It says please wait and nothing happens no matter how long wait, also ran the restore cd I made when I first configure iq506 hear spinning drive and also nothing happens.i can enter the parameter menu-esc stand f10 - f9 diagnostics-diagnostic shows path of cpu and memory all past harddrive cabin - was able to do the test hardware diagnostic tool before you get stuck at the loading bar on all past results - run test of the system to ensure that other hardware components work all passes - now the hp splash screen comes up then windows loading bar and that's it--is not any external equipment connected, do not load any new software or drivers. iq506 is about 2 years old also out of warranty ASSISTANCE

  It's robat1959 answering his own question for help - found problem original my computer to shut down to protect its self (bsod) could not do hard drive due to bsod tried recovery recovery using the disc I did for iq506 disc would spin then stop - went into the bios to change the order of hard drive stand , scanner - when in the bios seen hard but not optical disc drive when I see you stand readers, so I took computer apart and remove all cables from the optical drive - on computer and monitor hp open then sign in screen I enrolled and charge computer starts normally - defective optical drive was originally my bsod what a pain

• stacking n3048

  Hi, I have in my stock 6248 powerconnect, I want to stack if possible with the new template: N3048, is it possible? What cables? modules is necessary for the two models for this particular configuration? Thanks lotan

  Just like model switches can be stacked together. So the 6248 must be stacked with any other switch 6200 and the N3000 with another N3000. The switches must also be on the same firmware.

  part numbers 6200.

  3 meter stacking cable = G519F

  1 meter stacking cable = H798F

  Stacking module = UY108

  http://www.Dell.com/downloads/global/products/PWCNT/en/pwcnt_stacking_switches.PDF

  The N3000 series switches have two connectors for stacking of MINI-SAS fixed to the back.

  Page 176 of the user guide.

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_networking/esuprt_net_fxd_prt_swtchs/networking-N3000-series_Administrator%20Guide3_en-us.PDF

  Hope this information helps some.

  See you soon

• Windows 7 "Playback devices" do not recognize all options of reading?

  Hello

  I just changed my motherboard to a 'Gigabyte Technology Co., Ltd. model EP45-UD3P (Socket 775)"because my previous motherboard my have broken, (now I think that he could have the power supply, go figure).

  In any case, during the installation of the Windows 7 OS it have no sound options connected to the motherboard. The first audio option that I hung has my Philips flat screen TV via a HDMI cable to the video card. This was immediately recognized.

  Since then, I've hung up a Toslink cable to fiber optic to the motherboard to the receiver, this is not recognized at all.

  The only option that appear when you right click on the sound icon raise all the audio options and clicking on the 'reading devices' is the HDMI video card on television.

  Why Windows 7 will not be recognized the Toslink or analog options at the back of the motherboard?

  What can I do to fix this?

  I tried the tool audio Microsoft fixit, but nothing happened. Please, is there a way for it to work properly. Thank you.

  John

  After contacting the seller on eBay and them, which suggests looking in the BIOS I was able to get all the play back option to appear to "activate" the audio option under Advanced options in the BIOS.

  The seller said that this motherboard has already been used in a HTPC (Home Theater PC) and only the HDMI necessary option available.

  Here, the issue is resolved and I am able to listen to my music and movies through the optical audio or Toslink option so I'm a happy camper!

  Now, if only to get the IR to work with the remote for their 2250 Hauppauge TV card.