Adjust margin SNR on Cisco SRP527W-U?

Similar Questions

• Cisco SRP527w cannot find the user management tab

  Hello

  Can someone help me? I just bought a new Cisco SRP527w and I'm all new to this type of material. I can't find the tab for user management that I'm changing the default password.

  Also, I can't access the internet. My rj45 of the ADSL modem is connected to the WAN/LAN port with parameters IP static. What missed here? your help is very appreciated.

  Hi Ronald, if you are clicking on all other tabs and it still seems only the setup of the wizard, you must change your internet browser. Try Firefox or IE. This should solve that.

  -Tom
  Please evaluate the useful messages

• Cisco SRP527W-U feature question

  Hi, I have a configuration issue with respect to the Cisco SRP527W-U.

  We want to set it up as follows, 1) we have a termination ethernet for the WAN 2) we have 2 VLAN different, ranging from 2 different switches.

  Can we have the default gateway for LAN 2 subnets and a default route via a 30 for our WAN. Can I use the 4 switchports for this?

  switchport VLAN 2 (Switch 1 LAN) 1

  switchport VLAN 3 (Switch 2 LAN) 2

  switchport 3 VLAN 4 (link to the data center with 30 switch)

  Kind regards

  Scott

  Hi Scott Brien

  This model works as a layer 3 router, you can route the vlan and routing static, and another making works like

  Static routing

  Routing Information Protocol (RIP) versions 1 and 2

  (GRE) Generic routing encapsulation

  Point to point Tunneling Protocol (PPTP) - taken in charge on the primary WAN interface

  Layer 2 Tunneling Protocol (L2TP) - taken in charge on the first WAN interface

  Based on the routing strategy

  So, you can have the default gateway for your 2 LAN subnets and a default route via a 30 for your WAN

  If this answer is satisfactory to you, please mark it as response.

  Thank you

  Greetings, Johnnatan Rodriguez Miranda

• Cisco SRP527w Firmware/urgent fix

  Hello

  Having used various equipment cisco for years, I thought it would be a good idea to use an ADSL router for a job I'm doing for a client so I bought a SRP527w. I now regret buying it because it crashes regularly and needs a restart of the client which is annoying to say the least. The wireless sometimes stop routing requests to the DHCP server and what they lose connectivity. Also after a period of time the web interface stops responding if the traffic is still passing through the unit.

  Can someone link me please for the latest firmware and how to install it.

  Current firmware is:

  1.01.09 (001) April 7, 2010

  Thank you

  Hello Matt Clifford - the new firmware for the SPR527W is currently at 1.01.19. You can download this firmware on our Cisco.com site.

  I enclose the following link which should bring you to the download page for the new firmware.

  http://www.Cisco.com/Cisco/software/release.html?mdfid=282910822&flowid=797&softwareid=282919993&release=1.01.19&relind=available&rellifecycle=&RelType=latest

  When you download the new firmware save it on your desktop or somewhere where you want. Is the default IP for the SRP527W

  192.168.15.1. I would sign in the router using admin as the user name and password is Admin (there are 2 different users that you can use to connect to)

  This router - you can use cisco as id user and password or admin as password and user id. With the help of admin, you get more options when configuring the router) when you are in the interface of the router go to the Administration tab and you will see the option to upgrade the Firmware.  Navigate to the location where you placed the new firmware and then choose the file and begin the upgrade. After the router performs the upgrade, it is advisable to perform a factory reset on the router. Just hold in the reset button on the router

  for at least 30 seconds. After that, you should be ready to configure your settings and hopefuuly, you should be good to go.

  Thank you

  Rick Roe

• Or is the firmware of the cisco SRP527W please?

  Hello

  Now everything is in the title, indeed after a google search I find this page here: https://supportforums.cisco.com/docs/DOC-13853, I think that it is the privilege downloads Firmware SRP520 but it's 404 error. I'm afraid of being mistaken as the series is not accurate.

  Do I know or is the page of list of firmwares.

  Thanks in advance.

  Yes, those that should be good for the download.

  If you want browsing the Cisco's Web site, you can follow this instruction:

  • Go to www.cisco.com and click support

  

  • Click downloads, and then type SRP520, and then you can choose SRP520 or SRP520-U

  

  • At present, the page is interrupted by error 404

  

  -Tom
  Please mark replied messages useful

• VCS Cisco control / Core Expressway interoperability

  Hello

  I have the fate of unmanageable endpoints on the internal network, functioning as a H323 IP address directly.
  In fact, we had regular meetings as the auto numbering unmanageable endpoint by H323 IP address directly.
  Unmanageable end points would not be registered in the VCS / CUCM.

  1. can I adjust the composition of Cisco driver auto & GST to endpoints VC not saved by its IP address (regular meeting VC > Auto call the IP address internal VC endpoints directly)?

  2. or should I deploy VCS / Expressway to consume the traversal lic. / RMS lic. from autodial URI translate be IP call? Can I just deploy the VCS - C / E motorway in order to reduce the lic. costs?

  You don't need a VCS-E for this.

  Just go to the plan of numbering - Setup and call to unknown IP addresses as Direct. The alternative would be to create a subzone with a membership rule with the IP of your endpoint. Depends on if you want to only allow the call to this particular or to any endpoint IP on your network endpoint.

• Change the margins

  Hello

  I am a newbie. I created a web gallery in flash format.

  I would like to find a way to change the two topics.

  1. How can I adjust the margins surrounding the flash presentation? I would like to reduce the size of the margins to get rid of orders and the menu so I can incorporate this into a web page without taking up all of the extra real estate.

  2. I use the slideshow affecting only and I would firstly the flash presentation to start automatically once the page loads.

  Is this possible? Maybe in the java file?

  Adjust margins, etc in the Flash based Gallery is a bit tricky and more trouble than what it's worth, in my opinion. I would recommend one of the 2 solutions if you want to get into another Flash file.

  1. export the images and build your own gallery in your Flash file. It will give you more control over you want.

  If this isn't an option:

  2. review a few galleries of third party. SlideShowPro (www.slideshowpro.net) is a very popular option for export to Flash with many more options that you get from Lightroom out of the box.

• Questions of implementation of VPN IPSec 887-> srp527

  Hey people,

  I have a few problems to an ipsec tunnel between a cisco 887VA router and a cisco srp527w router.

  I have a few books and some example materials. I worked through many combinations of what I had and I'm still a bit hard.

  I look at the results of debugging and it seems that policies do not correspond between devices:

  05:44:37.759 Jul 23: ISAKMP (0): received packet of 500 Global 500 (R) sport dport XXX.XXX.XXX.XXX MM_NO_STATE

  broute1 #.

  05:44:57.079 Jul 23: ISAKMP: (0): purge SA., his 85247558, delme = 85247558 =

  broute1 #.

  05:45:17.031 Jul 23: ISAKMP (0): received packet of XXX.XXX.XXX.XXX dport 500 sport 500 global (N) SA NEWS

  05:45:17.031 Jul 23: ISAKMP: created a struct peer XXX.XXX.XXX.XXX, peer port 500

  05:45:17.035 Jul 23: ISAKMP: new position created post = 0x8838C3F8 peer_handle = 0x800021CF

  05:45:17.035 Jul 23: ISAKMP: lock struct 0x8838C3F8, refcount 1 to peer crypto_isakmp_process_block

  05:45:17.035 Jul 23: ISAKMP: 500 local port, remote port 500

  05:45:17.035 Jul 23: ISAKMP: (0): insert his with his 87 84664 = success

  05:45:17.035 Jul 23: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH

  05:45:17.035 Jul 23: ISAKMP: (0): former State = new State IKE_READY = IKE_R_MM1

  Jul 23 05:45:17.035: ISAKMP: (0): treatment ITS payload. Message ID = 0

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID seems the unit/DPD but important shift 0

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID is DPD

  05:45:17.035 Jul 23: ISAKMP: (0): no pre-shared with XXX.XXX.XXX.XXX!

  05:45:17.035 Jul 23: ISAKMP: analysis of the profiles for xauth...

  05:45:17.035 Jul 23: ISAKMP: (0): audit ISAKMP transform against the policy of priority 1 0

  05:45:17.035 Jul 23: ISAKMP: type of life in seconds

  05:45:17.035 Jul 23: ISAKMP: life (IPV) 0 x 0 0 x 1 0 x 51 0 x 53

  05:45:17.035 Jul 23: ISAKMP: DES-CBC encryption

  05:45:17.035 Jul 23: ISAKMP: SHA hash

  05:45:17.035 Jul 23: ISAKMP: pre-shared key auth

  05:45:17.035 Jul 23: ISAKMP: default group 1

  05:45:17.035 Jul 23: ISAKMP: (0): free encryption algorithm does not match policy.

  05:45:17.035 Jul 23: ISAKMP: (0): atts are not acceptable. Next payload is 0

  05:45:17.035 Jul 23: ISAKMP: (0): no offer is accepted!

  Jul 23 05:45:17.035: ISAKMP: (0): phase 1 SA policy is not acceptable! (local YYY. YYY. YYY. Remote YYY

  XXX.XXX.XXX.XXX)

  05:45:17.035 Jul 23: ISAKMP (0): increment the count of errors on his, try 1 of 5: construct_fail_ag_init

  Jul 23 05:45:17.035: ISAKMP: (0): could not build the message information AG.

  Jul 23 05:45:17.035: ISAKMP: (0): send package to XXX.XXX.XXX.XXX my_port 500 peer_port 500 (R) MM_NO_STATE

  05:45:17.035 Jul 23: ISAKMP: (0): sending a packet IPv4 IKE.

  05:45:17.035 Jul 23: ISAKMP: (0): the peer is not paranoid KeepAlive.

  05:45:17.035 Jul 23: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (peer

  XXX.XXX.XXX.XXX)

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID seems the unit/DPD but important shift 0

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID is DPD

  05:45:17.035 Jul 23: ISAKMP (0): action of WSF returned the error: 2

  05:45:17.035 Jul 23: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE

  05:45:17.035 Jul 23: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1

  05:45:17.039 Jul 23: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (peer

  XXX.XXX.XXX.XXX)

  05:45:17.039 Jul 23: ISAKMP: Unlocking counterpart struct 0x8838C3F8 for isadb_mark_sa_deleted(), count 0

  05:45:17.039 Jul 23: ISAKMP: delete peer node by peer_reap for XXX.XXX.XXX.XXX: 8838C3F8

  05:45:17.039 Jul 23: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL

  05:45:17.039 Jul 23: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_DEST_SA

  Here is a slightly adjusted version of my run-fig (came out I was sure that no one would need things) and attached are screenshots of IPSec and IKE Policy of the srp527w strategy

  version 15.1

  hostname broute1

  !

  logging buffered 65535

  information recording console

  !

  No aaa new-model

  !

  iomem 10 memory size

  clock timezone estimated 10 0

  Crypto pki token removal timeout default 0

  !

  !

  IP source-route

  !

  !

  !

  !

  VDSL controller 0

  operation mode adsl2 Annex A

  !

  property intellectual ssh version 2

  !

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  lifetime 28800

  ISAKMP crypto key PRE_SHARED_KEY_FOR_IKE (I_THINK) REMOTE_HOST hostname

  !

  !

  Crypto ipsec transform-set JWRE_BW-1 esp-3des esp-sha-hmac

  !

  !

  !

  IPSec-isakmp crypto 10 JWRE_BW-1 card

  defined peer XXX.XXX.XXX.XXX

  game of transformation-JWRE_BW-1

  match address 101

  !

  interface Loopback0

  no ip address

  !

  ATM0 interface

  Description - between node ADSL-

  no ip address

  no ip route cache

  load-interval 30

  No atm ilmi-keepalive

  !

  point-to-point interface ATM0.1

  no ip route cache

  PVC 8/35

  TX-ring-limit 3

  aal5snap encapsulation

  PPPoE-client dial-pool-number 1

  !

  !

  interface Vlan1

  Management Interface Description

  address IP AAA. AAA. AAA. AAA 255.255.255.0

  IP mtu 1452

  IP nat inside

  IP virtual-reassembly in

  no ip-cache cef route

  IP tcp adjust-mss 1420

  !

  interface Dialer1

  Description BETWEEN NŒUD ADSL-

  MTU 1492

  the negotiated IP address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  NAT outside IP

  IP virtual-reassembly in

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP chap hostname ADSL_USERNAME

  PPP chap password 7 ADSL_PASSWORD

  PPP ipcp dns request accept

  No cdp enable

  card crypto JWRE_BW-1

  !

  recording of debug trap

  access-list 101 permit ip 192.168.7.0 0.0.0.255 10.0.1.0 0.0.0.255

  Dialer-list 1 ip protocol allow

  Some specific questions:

  (1) on the PSR in the example I used (and I have a few PRS-> RPS VPN work) I see you enter the pre-shared key, I do not see in the examples I've used something on the IKE pre-shared key on the box of IOS. Does anyone have examples where you use the pre-shared for IKE? I wonder if it is my main problem as clearly says the newspaper there is no pre-shared key :|

  (2) I used a mash of names between different sections mish as on ESP the naming convention is not the same thing; IE: what parts of the IPSEC negotiation come from IKE policy and including the IPSEC policy section section. The names really matter across different ends of the VPN?

  (3) I noticed when I run this command in the(config-crypto-map): #

  defined peer FQDN

  It is converted to:

  defined peer XXX.XXX.XXX.XXX

  Should it? I want the camera to watch the FQDN that this particular host using DDNS and do not use a static IP address.

  I could ask 1 million questions, but I'll leave it for there, if anyone can see anything out (or can answer Q1 in particular) please let me know.

  Thanks in advance for your time and help people.

  B

  The IKE policy doesn't seem to match, you must configure the corresponding IKE policy on the router as follows:

  crypto ISAKMP policy 10

  the BA

  sha hash

  preshared authentication

  Group 1

  lifetime 28800

  For the preshared key, use the address instead of the host name:

  crypto isakmp key address

• with these changes, I can only print a page of print preview ability has been removed I use it all the time when you want to print something on a Web site

  When I was on a website and I tried to print a page, it allows to be a tab that says "FIREFOX" in the upper left corner of my screen, I could click on that tab and I had several options, one was "print" and "print preview". All the time, I use the Preview button before printing to see how the page would look like when I was feeling and how many pages there are. I could then choose to print all or part of an article and adjust it to what I wanted to print. I don't have this tab in the upper right corner. A tab for "open menu" is now in the upper right corner, however, in this menu is only a button 'print '. There is no option for "print preview" and so I can't address that I want to print. I could also adjust margins, etc. of a tab from the view, I can not find too. I really hope there are always options and how I find, where are they located?

  Print this button in Firefox 29 opens in print preview mode first.

• Photosmart 7510: Photosmart 7510 print offset of text to the right

  I use MS Word 2010 and when I print the text it seems 7 mm offset to the right. e.g. fixed left margin at13 mm starts printing at 20 mm, and right margin at19 set stop mm 12 mm printing. The same offset is displayed when you use other applications for example Publisher, Zara, Photoshop etc.

  Top, bottom, header and footer print exactly in the correct position.

  Of course, I can adjust margins to compensate for this error, but it is a bit a nuisanse and offends my sense of! I have had this printer for 3 years and the problem appeared right from the first day. I have other HP printers, but they do not display this problem. My printer is connected directly to the computer via USB.

  Hello @GreatSimms,

  Thanks for getting back to me on this subject. I'm sorry to hear that the steps I have provided could not solve the printing problem. If the impression is always shifted to the right that which usually indicate an alignment as the text is not aligned correctly on the page.

  Could I please have you run an alignment for me just see if that makes a difference.

  1. On the printer control panel, press the Setup icon (), and then tap Tools.
  2. Tap the align printer.
  3. After the compliance, prints an alignment page.
  4. The successful alignment is displayed. Press OK to exit the screen.
  5. Examine the printed alignment page. It should show all models of color - especially the black and blue patterns. The ink must not be streaked or indistinct.

  

  If the printed document appears to be centered, could I please have print you another document on your computer to verify that the problem has been resolved.

  Please let me know the result of the execution of the alignment. If the problem persists, there is an additional discount I have executed him. Good luck!

• HP Officejet Pro 8600 - Paper copy on the glass of the scanner, Officejet tries to copy the ADF

  I'm trying to copy a document on my HP Officejet Pro 8600.  I placed the original face down on the scanner glass.  There is no original in the ADF.  Then, I pressed "Copy" and "launch in black."  the Offficejet then "think" the original is in the ADF file and try to copy a non-existent original.  The Officejet then generates a paper jam «»
  in the ADF file' error message with instructions to clear paper jam and press 'OK' and spews a piece of paper from the paper tray. There is not an option for 'back '.  If I try to humor the Officejet by opening and closing the cover of the ADF and pressing 'OK', the Officeject generates a copy which is covered with black ink.  If I ask preview copy o, the document on the scanner glass is displayed.  I can adjust margins, etc.  When I select then 'copy' and 'Black start', the Officejet is trying to copy a nonexistent document in the ADF and generates the "Paper jam" message again.  Since there is not an option "go back", I turn the printer off, then turn it back on, and then try again.

  How do I train me or the Officejet for copy of the scanner glass when the original is located on the glass of the scanner NOT the ADF?

  Thanks for your help to solve this frustrating problem.

  Hi Knitter507,

  Try to do a hard reset as described in the following link.  Click here

  If that doesn't help, can you print a printer status report and give me the a.) Product # and B.) Version of the firmware of the printer?  To print the report, press on the arrow to the right on the screen of the printer control and then configure / reports / Printer Status Report.

  What is the operating system for your computer?

  You are able to make a hollow photocopy the ADF?

• Different multiple images on 1 Page, selected order.

  I know how to print several different images on 1 page, but I want to place on the page in the order that I chose it IE... 1.2... 9.

  You can try to place all 9 photos in Microsoft Word.  Simply remove/adjust margins to so that all the pictures all go in a photo paper once you print it.

  

  Let us know how it goes.

• SRP527 - Intervlan does not

  Hello

  I wish that my router SRP527 to manage the VLAN 2.

  1 for my whole LAN and WIFI connections to employees, one for external access to Internet by WIFI SSID guest clients.

  -J' have this router Cisco SRP527W acting as a bridge between my network and the Internet.

  -J' have a second router used for VPN between my LAN and 2 external agencies connections.

  -My LAN uses 192.168.0.0 / 255.255.255.0 network

  -External agency 1 uses 192.168.1.0 / 255.255.255.0 network

  -2 external agency uses 192.168.3.0 / 255.255.255.0 network

  The Cisco router using VLAN 2:

  -The VLAN 1 (port LAN 4 and 1 SSID)-> 192.168.0.254 / 255.255.255.0

  -THE VLAN 3 (SSID 2)-> 10.33.0.254 / 255.255.255.0

  The Cisco router uses 2 static routes:

  -Agency 1: 192.168.1.0 / 255.255.255.0-Gateway 192.168.0.249 >

  -Agency 2: 192.168.3.0 / 255.255.255.0-Gateway 192.168.0.249 >

  The VPN router for external agencies is to use 192.168.0.249 / 255.255.255.0.

  When the router SRP527W intervlan routing activated, everything works. I can ping my external agencies. However, external clients using WIFI comments can also ping my internal LAN.

  Intervlan routing separate VLANS and VLAN 1 disable 3 correctly, but I cannot ping my external agencies more and I don't know why?

  Behind my Cisco router:

  -Switch Gigabit HP 1 (servers, router VPN are connected)

  -2 switches (HP and Accton) both related to the gigabit switch and where all of my clients are connected.

  No connection trunk and vlan are defined on my switches.

  The CISCO Hotline has not found the answer. I have the latest version of the firmware. Can you help me determine why disable intervlan routing stop link between my LAN and external agencies?

  Thank you

  Hi Adrien,.

  If intervlan routing is disabled, traffic is allowed only to pass traffic between the LAN and WAN interfaces, not LAN to LAN.

  You want to know that the new product SRP527W-u includes support for wireless access, so it might be more appropriate for your condition.  (The code that enables this feature is not supported by the SRP527W that you have.).

  Kind regards

  Andy

• SRP527 W

  Hello

  On Cisco SRP527w cloning mac address works on Wan?

  my ISP need an address mac specific for adsl2 +.

  Thank you

  Alessio

  Hello Alessio,

  Yes, the SRP527 supports this for the ADSL PVC.

  Kind regards

  Andy

• HP Chromebook 14: Problem printing

  Newbe here - hope I'm in the right forum. Re: HP Chromebook 14 - printer Epson XP-410. When you print a document, it prints with all shifted to the left instead of being centered. Have not been able to adjust margins to fix.

  Olaide wrote:

  Newbe here - hope I'm in the right forum. Re: HP Chromebook 14 - printer Epson XP-410. When you print a document, it prints with all shifted to the left instead of being centered. Have not been able to adjust margins to fix.

  Printing problems Epson to contact Epson support...