AIR-WLC8-K9 configuration guide
I have tried to locate the guide configuration or examples for the NME-AIR-WLC on the OCC, but couldn't find one. Grateful if someone could share this info.
Hi Rohan,
Maybe this will help you get started;
Examples of Configuration of WLAN Controller Module (WLCM)
http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_tech_note09186a00807112e2.shtml
http://www.Cisco.com/en/us/products/ps6730/tsd_products_support_model_home.html
I hope this helps!
Rob
Tags: Cisco Wireless
Similar Questions
-
Red Hat Enterprise Linux Configuration Guide for Dell storage bays Series PS
This configuration guide provides information on the integration of the RHEL 6 and 7 operating environments with the PS Series Dell storage arrays using iSCSI technology. The guide includes tips for working with volumes, using MPIO and some performance tips.
The PDF file is available here:
Kind regards
Don
Hello
With Linux, as any OS, iSCSI is not different from the SAS/SATA or Fibre Channel. No matter how you are connected to a "disk", it looks like a SCSI to the OS disk.
So yes, you use the mount points. That's how Linux as most UNIX operating systems do it. But use any method supported for other iSCSI disks. In Windows, you can use drive letters or mount points.
Kind regards
Don
-
EqualLogic Configuration Guide - delay of the ACK
I see no mention of disabling ACK delayed in VMware ESXi in the EqualLogic Configuration Guide 14.1.
It is more a best practice?
If it is always advisable, what official document of Dell says this?
Thanks in advance :)
Yes, it's always considered best practices. You can view information about this here:
In addition, the KB on the EqualLogic Support site has additional information. Just search for "delay acknowledgement '.
-joe
-
Hello
I would like to set up and test AAA on a Cisco ASA (5505 or 5510).
1 are there any other tools or server required to use this feature? And you have good configuration guides?I already tested a CDA of Cisco. He was able to show users active directory and their IP equivalent.
2. do you have a brief explanation what kind of opportunities I have with this server/tool? It is perhaps usable for the AAA mentioned on the SAA?Thanks in advance
Best regards
1. Yes, you need a Radius like Windows Server NPS or RADIUS server such as Cisco ACS/ISE server.
2. He's just a man in the middle of the ADC, you will always need an AAA server: radius or Ganymede (see # 1).
-
Uplink Ports Fibre Channel - UCS GUI Configuration Guide
Hi all
Could someone please explain which means that what follows in the Configuration of GUI of UCS guide @.
Uplink Ports Fibre Channel
Manage ports Uplink Fiber Channel FCoE traffic between the interconnection of fabric and the next layer of the
SAN storage network. All FCoE network-related traffic is pinned to one of these ports.
By default, the Fibre Channel ports are uplink. However, you can configure them to work as Fibre Channel
storage ports. This is useful in cases where a Cisco UCS requires a connection to a DAS storage
Device (DAS).
My question is, how the FC Port could handle FCoE traffic? My understanding was that FCoE will be lifted and Enthernet connection only.
Thanks for your help
Concerning
Vikas Srivastava
The CF module interconnection fabric is the place where the speration of CF vs. FCoE happen, so it's where the FC frame is extracted in the Ethernet frame.
-
Hello
I have 4 NIC in Server Blade 7 (ESXI 5), would like to dedecate 2 NIC for (Vmnetwork, management and vMotion) & NIC (iSCSI traffic) 2 with equallogic SAN.
I equallogic guide to configure ESXI with it, but how do I configure (Vmnetwork, management and vMotion) with NIC 2, my priority is excellent speed for my virtual machine, and then nothing else.
Then just go for classic switch.
The configuration is a lot depend on existing infra, the trunk, the physical switch for redundant network & balance, 100 or network 1GbE, no.. virtual machines and etc. If there is a new configuration, I suggest you trunk 2 x available vmnic (the vm network) to balance the load and better performance.
-
Basic Test Lab Configuration Guides: Windows Server
Dear all
I'm asking for help for the following
We have just a lab Cisco isolated from our network, we have 5 students and I want to help them with
establishment of a laboratory to test in a virtual environment, the goal is to teach them how to create a network, run the following
DC + 2 workstations
I'm looking for Guides to basic setup and Test laboratories in a virtual environment
Windows Server 2012r2 & Windows 7 Enterprise
Windows Server 2008r2 & Windows 7 Enterprise
Hello
Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.
http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer
See you soon.
-
Please, could you guide me for ASA 5506-X document management?
Thank you
Hello team,
Here are a few reference link which may help you.
http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/5506X/5506...
http://www.Cisco.com/c/en/us/TD/docs/security/firesight/541/firepower-mo...
http://www.Cisco.com/c/en/us/support/security/ASA-firepower-services/Pro...
Note If the post will help you
Concerning
Jetsy
-
Configuration of WiFI AIR-BR1310G-A-K9-R encryption
Aironet model: AIR-BR1310G-A-K9-R
IOS: Cisco IOS Software C1310 (C1310-K9W7-M), JA Version 12.4 (10B), VERSION of the SOFTWARE (fc2)
Hello:
I inherited a WLAN with three AIR-BR1310G-A-K9-R routersconfigured APs as well as two other access points
of a different mfg in the same WI - FI HotSpot. Three Cisco access points have been defined for the WEP encryption
While other than Cisco both were installed for WPA2-Personal. There seems to be no particular reason for the WEP-
differences in encryption WPA2-vs other that this is the default for both, apparently.
My question is, what encryption types supports the Aironet 1300 series, it is only WEP? I have
would like to have more options than WEP just for the BR1310s, is - it possible? When I log in the
HTML of the Cisco router page and look at encryption it shows only WEP in option. I was told that there are no later
version of the IOS, IOS of AP autonomous software - 12.4.25d - JA2, offer WPA or above encryption?
Thanks in advance for your time and your consideration.
Doug
With 12.4.25d - JA2 IOS, you can configure WPA2/AES on 1310 as well. I had a PA model 1310 & I set & checked.
Here's the basic involved config. (I simply configured DHCP on AP it yourself & you can change it in your case)
1310-1 #sh worm
Cisco IOS software, software C1310 (C1310-K9W7-M), Version 12.4 (25 d) JA, RELEASE SOFTWARE (fc1)
DHCP excluded-address IP 192.168.178.1 192.168.178.50
IP TEST dhcp pool
network 192.168.178.0 255.255.255.0
router by default - 192.168.178.1
!
SSID dot11 TEST
open authentication
authentication-key wpa version2 management
Comments-mode
WPA - psk ascii Cisco123
!
interface Dot11Radio0
encryption ciphers aes - ccm mode
SSID TEST
!
interface BVI1
192.168.178.1 IP address 255.255.255.0
% DOT11-6-ASSOC: Interface Dot11Radio0, Station 04f7.e4ea.5b66 associated KEY_MGMT [Wpa2 PSK]
Here's the configuration for this version of IOS guide
HTH
Rasika
Pls note all useful responses *.
-
We use the information provided in the following document: i.dell.com/.../dell-networking-n4000-series-switch-configuration-guide-for-equallogic-sans.pdf
We have two switches of N4032F which are stacked and followed almost word for Word from this document. We do not use DCB. We are trying to set up a SHIFT and follow-up step 2.11 in the document, but it seems that the SHIFT does not work.
Switch 1:
serial interface fortygigabitethernet 1/1/1-2
No spanning tree portfast
active in mode channel-group 1
Switch 2:
interface series fortygigabitethernet 2/1/1-2
No spanning tree portfast
active in mode channel-group 2
However, when it was discovered after changing these settings it shows them as being inactive.
Can someone please help?
Thank you
Jeff
Thanks for the additional information. When the switches are stacked, they act as a logical switch. Then when you plug with an OFFSET you are basically creating a loop and hook up a switch on himself. Desempilement switches and just use the OFFSET for the interconnection of the switch and you should see the GAL go active.
-
Nice day
Can someone point me to a FWSM configuration guide please?
I had a quick glance, but found no one.
Thank you very much
Please look here:
http://www.Cisco.com/univercd/CC/TD/doc/product/LAN/cat6000/mod_icn/FWSM/fwsm_2_3/index.htm
I hope that's what you're looking for...
Please rate if useful.
-
Add AIR-LAP1522AG-E-K9 to the FCC (-) field of regulation
Hello
I would check with you experts, it is possible to register for AIR-LAP1522AG-E-K9 to our existing WLC who has (-A) configuration of FCC?
It is a network of outdoor mesh and all other access points are AIR-LAP1522AG-A-K9 (FCC).
I always get an error that it has an invalid country code, and I couldn't even do a ping it after having acquired an IP address from the DHCP server.
Any help would be appreciated. Thank you.
Hello
You may want to consider this WLC setting;
Version 4.1 or higher.
Configuration of country Codes
Controllers and access points are designed for use in many countries with various regulatory requirements. The radios in the access points are assigned to an area of specific regulation in the plant (e.g.-e for Europe), but the country code allows you to specify a particular country of operation such as (FR for the France) or TO the Spain. A country code Setup ensures that the emission of radio frequency bands, interfaces, channels and transmitting power of levels conform to regulations.
Generally, you configure a country code by the controller, one corresponding to the physical location of the controller and its access points. However, version 4.1 or later of the controller software allows you to configure up to 20 codes of countries by the controller. This support for multiple countries allows you to manage access points in various countries of a single controller.
--------------------------------------------------------------------------------
Note well that the controller supports different access points in the different regulatory domains (countries), it requires all the radios in a single point of access to be configured for the same regulatory domain. For example, do not configure a Cisco 1231 802 access point. 11 b / g radio for the United States (-) regulatory area and its 802. 11A radio for Britain (-E) regulatory area. Otherwise, the controller allows only access point radios to market, according to which regulatory area, you have selected for the access point on the controller. Therefore, make sure that the same country code is set to two radio access point.
The good doc.
http://www.Cisco.com/en/us/docs/wireless/controller/4.2/configuration/guide/c42lwap.html#wp1147748
I hope this helps!
Rob
-
How to configure repeater using aironet 1140?
Hey,.
I have an Air-AP1141N-A-K9 and I want to set up a Repeater bridge. I already have the web interface to the top. I was wondering how to set up as a Repeater for my main router. I think that it only supports 2.4 Ghz
The IP address of my main router is
192.168.1.154
2.4 Ghz channel 2
SSID: Wolf
I was able to set up a Repeater bridge using a dd - wrt installed the router but I can't figure out how to do it with the access point Cisco
Thank you
Hi Josh,.
I assume you are using a CISCO IOS Gateway running as a parent to another access point Repeater running Cisco's IOS cannot associate with
access points to the parents who who are not IOS running.
If you use an access point CISCO as a parent... then make sure that the settings on the Parent and the Repeater exactly except matches IP ADDRESS and the ROLE of STATION...
To set the same as Repeater... Here are the steps...
To the CLI HELP - issue the 'repeater station-role' command under the interface of the AP Radio.
With the HELP of GUI - click network interfaces > int > 802.11 G Radio > settings > here you can > Repeater > click it and apply.
Let me know if that answers your question... Don't forget to mark it as answered if she answered!
Concerning
Surendra
====
Please do not forget to note positions that answered your question and mark as answer or was useful -
Max AIR-LAP1142N-E-K9 Access Point devices
Hello
How many Wifi devices simultaneously press a Point of access AIR-LAP1142N-E-K9?
Thank you
Hello
I hope that you are looking for the maximum clients that supports the TOWER... Here flax kwhich gives you the exact information you're looking for...
http://www.Cisco.com/en/us/docs/wireless/controller/7.0/Configuration/Guide/c70ccfg.html#wp1085099
Let me know if that answers your question...
Concerning
Surendra
====
Please do not forget to note positions that answered your question and mark as answer or was useful -
need urgent help with AIR - LAP - 1242 G-E-K9
Hi all
IM new in the Cisco wireless. I have a Cisco AIR-LAP1242G-E-K9... I don't WLC, I want to use it as standalone AP for wireless access to my users... I took the AP console & got the following msgs!
AP68ef.bde3.3ad4 #.
AP68ef.bde3.3ad4 #.
AP68ef.bde3.3ad4 #.
AP68ef.bde3.3ad4 #.
AP68ef.bde3.3ad4 #.
* 00:18:55.021 Mar 1: % CAPWAP-5-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
Not in a bound State.
* 00:19:05.651 Mar 1: % ADDRESS_ASSIGN-6-DHCP: Interface FastEthernet0 assigned address DHCP 172.10.10.16, mask 255.255.255.0, hostname AP68ef.bde3.3ad4* 00:19:10.524 Mar 1: % 3-CAPWAP-ERRORLOG: white event 29 & combination State 4.
* 00:19:10.524 Mar 1: % 3-CAPWAP-ERRORLOG: SM Manager: failed to process the message of the timer.
* 00:19:10.524 Mar 1: % CAPWAP-3-Journal of ERRORS: do not handle the message from the timer.
* 00:19:10.525 Mar 1: % CAPWAP-3-Journal of ERROR: failed to process the message of the timer.
* 00:19:10.525 Mar 1: % 3-CAPWAP-ERRORLOG: Discovery interval timer Manager time-out failure.
* 00:19:10.587 Mar 1: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 1 Mar 00:19:10.587: bsnInitRcbSlot: slot 1 has NO radio
* 00:19:10.595 Mar 1: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 00:19:10.608 Mar 1: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to
* 00:19:10.609 Mar 1: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
* 00:19:12.606 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.Translate "CISCO-LWAPP-CONTROLLER"... the domain server (255.255.255.255)
* 00:19:21.607 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER* 00:19:30.608 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-LWAPP-CONTROLLER
* 00:20:20.614 Mar 1: % CAPWAP-5-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
Not in a bound State.
* 00:20:31.244 Mar 1: % ADDRESS_ASSIGN-6-DHCP: Interface FastEthernet0 assigned address DHCP 172.10.10.17, mask 255.255.255.0, hostname AP68ef.bde3.3ad4* 00:20:36.117 Mar 1: % 3-CAPWAP-ERRORLOG: white event 29 & combination State 4.
* 00:20:36.117 Mar 1: % 3-CAPWAP-ERRORLOG: SM Manager: failed to process the message of the timer.
* 00:20:36.118 Mar 1: % CAPWAP-3-Journal of ERRORS: do not handle the message from the timer.
* 00:20:36.118 Mar 1: % CAPWAP-3-Journal of ERROR: failed to process the message of the timer.
* 00:20:36.118 Mar 1: % 3-CAPWAP-ERRORLOG: Discovery interval timer Manager time-out failure.
* 00:20:36.183 Mar 1: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 1 Mar 00:20:36.183: bsnInitRcbSlot: slot 1 has NO radio
* 00:20:36.190 Mar 1: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 00:20:36.203 Mar 1: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to
* 00:20:36.204 Mar 1: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
* 00:20:38.202 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.
AP68ef.bde3.3ad4 #.
AP68ef.bde3.3ad4 #.Due to frequent changes in intellectual property, I can't make the console AP...
Can any body tell me what is the problem & solution... & it will be appreciated if any body share the basic configuration guide
Thanks in advance &
Please answer as soon as POSSIBLE...i want to use it as standalone AP for wireless Access to my users
Me bad. Let me explain. You need a PA running an IOS (aka autonomous) autonomous.
*Mar 1 00:18:55.021: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Maybe you are looking for
-
BEC: My screen won't work!
I have a HP computer germinate. Using the touch screen, I slipped left give me some options such as the hours of night. Because I was going to turn down the brightness, I clicked another option, have to do with the different screens (I don't remember
-
"What's NEW" page opens every time you start FF
Hello! After update to 9.0 (9.0.1) whenever FF starts, it opens the page "NEWS". I always close. But it looks like persisted! Please suggest what to do?
-
I created a labview project that contains about 40 vi. Each vi has a joint control panel which is a group of ip address, or address of the port and the parameters that are passed high-level vi at low level vi for the purpose of control and access ou
-
Make sure you have directx9 and video drivers installed BVRP software
-
Cannot get my usb card reader to work because I plugged my new wireless broadband
HI MY PLUG-AND-PLAY DIRECTED BY ABC PRODUCTS USB CARD READER WAS WORKING UNTIL WEEK LAST I CHANGED MY CONNECTION TO BROADBAND CABLE TO CONNECT NEW WIRELESS I UNPLUGGED AND REPLUGED INSIDE BUT STILL DOES NOT? JOHN SOON