AirPort Extreme does not channel 5 GHz

Similar Questions

• I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

  Turn off the new modem for at least 30 minutes. More is better.

  Perform a hard reset on the AirPort Extreme, then it turned off.

  Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

  After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

  Then, turn on the airport and let it run a few minutes

  Set up AirPort Extreme again

  Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

• AirPort Extreme does not appear in the Finder.

  I can't connect to the Internet and the configuration of the AirPort Extreme using AirPort Utility. Yet I can't find the AirPort Extreme on Finder. It gets frustrating because I use a disk external DRIVE plugged into the USB Extreme preferred airport for backups with Time Machine.

  I tried my network power cycle but nothing has been fixed. Any help?

  The base station itself appear not in the Finder. To access a connected drive, use the connection to the server command in the menu go to, provide the IP address of the base station, and where applicable, check the boxes in the general and tabs box preferences from the Finder for her.

  (140347)

• Airport Extreme will not read Time Capsule trying to create network roaming

  I have read all the forums on that alone and became frustrated. I am creating a roaming network for a time at an airport extreme capsule. I followed the directions of countless times without success. Time Capsule is set to DHCP and Nat, while the extreme is in Bridge Mode and has the exact same name and password network settings. Now, I have to say that the ethernet cable connecting is extremely long (well over 100 meters) and I know that the connection will degrade, some, but my lap top is able to capture the signal when I connect it directly to the cable coming from the time Capsule, so I know that the cable works. In fact, this is how I am writing this post right now! My problem is that the Airport extreme will not even read the time capsule at all. Can someone help me please? A friend told me that I might have to configure the router second to accept the connection at a slower pace? I don't know what that means. Sorry to be a pain.

  has the exact same name and password network settings.

  Just to double check that you mean the password and the name of wireless... not the base station name and password the names of base station must be different.

  Now, I have to say that the ethernet cable connecting is extremely long (well over 100 meters) and I know that the connection will degrade, some, but my lap top is able to capture the signal when I connect it directly to the cable coming from the time Capsule, so I know that the cable works.

  To the limit sometimes the gradient exceeds just slower... it does not connect.

  If you check the laptop goes to the Advanced preferences network ethernet to the last tab has the speed dropped to 10Mbit? The extreme is not able to go as low automatically... and unfortunately there is no controls for the later models.

  

  What model is your extreme?

  If it's a Gen5 or an earlier version... you can use older airport utility to set the speed of the wan port. This feature is removed from models later, of course... and the AU later so does she. If you can go try it using full duplex 10mbit. If that works try 100mbit full duplex, but you might find it's too fast.

  

  A friend told me that I might have to configure the router second to accept the connection at a slower pace?

  Your friend has a good idea.

  I would have cut the cable in the middle... and put an end to both ends. Then place a switch on the line (not a router). A switch is a bit like an amplifier. It is to retransmit the signal so it can go another 100M...

  The other issue is on pairs... If you have installed this cable yourself and terminated yourself you were affecting the pairs?

  Ethernet is delicate to the wire because of its origins as the wiring phone... where the Center pair is for the phone.

  MacBook won't connect to the Internet via long cable?

  Here is a very similar problem to yours... was bad ethernet endpoints. Break the pairs at your own risk.

• the Airport extreme appears not on the graphic overview

  the Airport extreme appears not on the graphic overview

  Everything plugged and works

  Unable to connect with the personal network

  By graphical overview, I presume you are talking about airport utility?

  Are you using wireless or ethernet?

  You have run diagnostic wireless on your Mac if you use wireless?

  Use Wireless Diagnostics helps you troubleshoot Wi - Fi on your Mac - Apple Support

• Connected to but the Airport utility does not see the time capsules

  Hi, I have several time capsules.

  I can connect to the web, but the airport utility does not see the time capsules.  I tried to restart the time capsules, router, computer, but I still don't see any of the devices on the network.

  What now?

  Have you tried the airport utility in the iOS version... Download on the App or iTunes store and load... Works better than the Mac version.

  Other than what Mac running what OS do you use?

  This modem you have and how is the installation of TC on the network.

• I lost my WiFi signal after having placed a time Capsule in the system. Now the Airport Extreme will not recognize the system. Any ideas?

  Any ideas on why my Airport Extreme will not recognize the system after the integration of the time Capsule in my system? Continues to have a flashing yellow light after trying all suggestions of technicians from the Apple Store and Internet provider.

  Since we don't know all what has been tried, we will have to start from the beginning if you don't mind.

  What exact models are your AirPort Extreme and Time Capsule? What is the brand and model of your modem Internet? I'll assume that Extreme is your "main" router and is directly connected to the modem by Ethernet... correct?

  Do you have the Time Capsule (TC) connected to the extreme, by wire or wireless? What is your goal for the TC? In other words, will not be used to extend the reach of the extreme wireless?

• Airport utility does not support my Airport - options to change the channel?

  I have an older Airport - extreme, I think, and the utility does not support.  I'm out of luck to change channel?  Time Warner said their modem did not support my newest Airport (? it's TWC) and now the internet keeps smoking at least once or twice a day.

  I suggest that you keep it simple.

  Your airport automatically analyze and choose the best channel to use when it lights up. So, if you have not done for some time, powering to the airport, wait a few seconds and then put it to the top.

  Even if you could change the channel... How would you know which channel to choose?

  Time Warner said that their modem did not support my most recent airport

  Time Warner will only support for a product they have received for you.  But this does not mean that a router from Apple will not work with their service. I've used Apple products for over 10 years with Time Warner.

• Linking New Extreme old Extreme and Express. New Airport utility does not recognize old Extreme/Express

  I had a linear new extreme connection (connected to the wireless model Cat5) related to the old extreme then Express (newish).

  I would have put in place using airport Utility (for example) 4 years ago and has worked well.

  I changed my wireless modem (formerly broken) but cannot now reconnect the old extreme and express to the extreme again.

  The extreme new connects to internet just fine as long as it is in Bridge mode (does not work in DHCP/NAT mode).

  My real question is the utility software Airport now seems not to recognize the Express extreme or old old to get re-connected.

  The manual of Apple still shows configurations using the old utilitarian approach Airport (with each unit sitting on LHS page)

  If you're still using OS X (10.5.8)... as, you enter in your profile information... then the AirPort Utility in this operating system must be able to recognize the old AirPort Extreme and Express.

  However, if you have updated to a new operating system such as the Mountain Lion (10.8.x), Mavericks (10.9.x), Yosemite (10.10.x) or El Capitan (10.11.x)... and... you have more "round" or version 'dome' in the form of AirPort Extreme, and an old version of the AirPort Express A1084... so, the new version of AirPort Utility is not compatible with older airports.

  So, this would help a lot if we could get clarification from your part...

  (1) what operating system you're using now?  If you are not sure about this, click on the Apple icon in the upper left corner of the screen, then click on about this Mac and post back with the Version of OS X number that you see there.

  (2) what version of the AirPort Extreme you may have.  Is it a 'rounder', or 'dome' in the form of version... or... The "flat" or "square" version? If you have flat or square version, the number of model of the device is required. It is on the lower part of the airport, probably integrated in the base of carpet of MOSS. The model number starts with an 'A' follow-up of four digits. Please post back this information.

  (3) what version of AirPort Express you have?  Please look for the model number on the side of the Express. It is difficult to see, with grey lettering in a certain context, so you need to perhaps good lighting and glasses to discern the number of reading.  As extreme, the Express, model number starts with an 'A' followed by four digits. Please post back this information.

  Once we have the information we need, we know more about how to proceed from this point.

• Airport Express does not work

  I need help. I have an Apple Airport Extreme and extend it with an Apple Airport Express. One day I needed to my extreme, which I did, forward port (which was for the xbox, and I followed this: Xbox NAT open (Apple routers)) I then updated my Airport Extreme. Subsequently, my Express glows green but it does not actually give a signal, I stay connected to the extreme, so I tried to use ethernet with the Express, and who won't let me connect to the Internet. So, I need help.

  If the Express was created to connect to the AirPort Extreme using a Wi - Fi connection, and you later connected to an Ethernet cable to the Express... that creates a huge feedback loop that actually blocks the network provided by the Express.

  You will need to restart and reset the Express back to default settings, then set up again.

  If you want the Express to connect permanently at any time to the extreme by using an Ethernet cable, then you must establish this connection before you implement the Express again. The Ethernet cable can never be disconnected.

  If you want to Express to extend the wireless network, then you use an Ethernet cable to the installation.

  If you need more tips, post back to let us know what operating system your Mac is running or you use a PC or an iPhone / iPad to configure things.

• The airPort Extreme is not working after Firmware update

  Hello

  At our office, we have several AirPort Extreme or TimeCapsules and one of them (AirPort Extreme) stop working properly after the update 7.7.7

  The update itself is supposed to be ok and we have updated all our stations but it only seems to not work. I have hard and factory reset and somehow until last month worked more less, but from this week completely stop working and even reset does not work.

  I already ran out of ideas and it seems that Apple wants to charge me $ 30 for a phone call.

  Someone at - it a similar case? Should I take on the Apple Store?

  Thanks in advance for your help.

  You can get it replaced if it is less than one year... That is to say in the warranty or if you have any computer or ipad or apple TV which is covered by the applecare will also cover the airport up to 3 years old if EI is less than 2 years, you can still buy applecare on a product calling... or you can buy say an apple TV and buy applecare for it.

  If Apple do not repair them. only, they will be replaced.

• my airport express does not extend to my network

  Hello to you all guru out there...

  I 5g internet and comes with the router and signal is fantastic in the main lounge, but it is a large apartment and once I get my room the signal decreases considerably.

  I bought an Airport Express and it connects to the wifi perfectly, green light and everything, but it does not extend my wifi network...

  Do I need to have another Aiport Express hooked up to the main router, then extend the Airport Express wifi or should I get an Airport Extreme?

  Any advice or help is greatly appreciated.

  Thank you!

  Do I need to have another Aiport Express hooked up to the main router, then extend the Airport Express wifi

  Yes, the "main" AirPort Express should be connected to your router using a wired Ethernet cable connection, permanently. This Express will be set to "create a wireless network.

  Other Express your distance can then be configured to "extend a wireless network.  In its current form, your existing Express is configured to "join a wireless network.  It will work for AirPlay like that, or allow you to connect a supported USB printer, but it cannot extend a network provided by a third-party router wireless.

  Regarding matching them things, it would make sense to use two airport expresses, or the two extremes of the airport.  The extreme might be your "primary" router if you wanted to, but the Express would not be able to expand the capacity of faster speed to the extreme.

• Airport Extreme is not displayed on the plan of airport utility

  I have just connected an old Airport Extreme 802.11ac but does not appear on my map of Airport utility. I try a soft, hard and factory settings and still not showing not allowed me to set up, so had to use my PC to put in place and work fine, but I still not able to set it up using my MAC and does not appear on the usefulness of the airport; What can I do?

  Make sure that your Mac OS X is up to date.

  Open the App Store, and then select the updates menu.

  It should certainly appear in AirPort Utility window.

  

• AirPort Extreme will not do handshake to connect devices.

  I don't know if my question is related to the Cox IPv6 problem, but here goes...

  I have a signal of quality, checked cable modem and my extreme is the latest generation with the latest version of the installed software package green watch on Internet and the Base Station Airport utility.

  My Network recognize my password, but it does not connect... The box will not be displayed, just the circle of rotation for ever.

  I have hard to restate the modem, I completely rebooted from the base station and deleted and restarted my home network. Everything seems to work!

  Any ideas?

  This modem do you have?

  There are two main issues...

  On Cox IPv6 is a problem... so put IPv6 to post a link-local only in the router and the computer.

  Then the problem is more fundamental... Some modems do not work with the airports of HQ... a single serial port modems SB are the worst offenders, but many others have problems... nothing is apparently not with one of them... but the combo does not work.

  Sometimes it's just easier to buy another router of brand... and connect at the airport bridge purely as WAP... so it has no routing and so very little to go wrong.

• My AirPort Extreme end not implemented with the help of AirPort Utility

  Bought a used AirPort Extreme (Genesis 4) of a person who showed me that he worked at home. When I try to set up as a Wireless extender to my last existing AirPort Extreme, he will not carry out synchronization upward with AirPort Utility. It appears as a new extreme, but get a message 'unexpected error' before or after the name. Have you tried to reset the two while it is powered and turning the as explained in the help.

  When I try to set up as a Wireless extender...

  Gen 4 airport will connect to your existing AirPort Extreme wireless... or... it will connect using wired Ethernet wired, Permanent?

  .. .it will not accomplish the synchronization upward with AirPort Utility.

  Which version of AirPort Utility?  If it's on your Mac... and you don't know what version you have...

  Open AirPort Utility

  Click the AirPort Utility menu in the upper left corner of the screen

  Click on about AirPort Utility

  Report on the version number you see here

  You have an iPhone or a handy iPad that could be used to implement the 4th Gen airport if the problems continue with the help of your Mac?