AnyConnect connection attempt failed

Similar Questions

• Cisco AnyConnect VPN Client (connection attempt failed because the network or pc problem cisco)

  Hi all

  I am trying to connect to my Cisco AnyConnect VPN Client but everytime I try, I get an error (connection attempt failed because the network or pc problem cisco)

  Can anyone help me please with this.

  Thank you

  Zia

  What is the local firewall on your computer?

• The connection attempt failed because the modem (or other connecting device) on the remote computer is out of use. Error 777

  I've always used my blackberry to tether my phone but I get the following error message and I can't solve this problem, any help would be appreciated, thanks!

  The connection attempt failed because the modem (or other connecting device) on the remote computer is out of use. Error 777

  Hello

  It seems that the blackberry is not more.

  Pass the installation attaches on the blackberry and make sure that it is configured properly and work.

• Unable to connect to the host server: a connection attempt failed because

  Hi all

  I install my host ESX server in vmware workstation.  It works fine except when I am creating virtual machines.

  I'm not able to install the operating system on the virtual machine and I get this error that appears inside the virtual machine.

  Unable to connect to the host server: a connection attempt failed because the connected party did not respond after a certain time, or established connection failed because connected host has no

  to answer.  Do you want to retry?

  My ESX server hosts have static IP addresses.

  I've seen a few similar posts on this issue, but their solutions have not worked for me.

  Best regards

  Nathan

  I think we confuse you.  ESX server is running like a machine virtual within the workstation, correct?  If Yes, then you must edit the vmx esx server with these entries monitor configuration file *.  They can go anywhere in the file.  Once those have been added, you should be able to run 32-bit virtual machines within the esx server.

  -KjB

  VMware vExpert

• How to connect success and details of connection attempt failed router to Syslog?

  All,

  How can I configure my router Cisco 837 to log to syslog all successful and attempted connection failed to the router via any interface?  I would like to get very verbose information about attempts to connect (success and failure) as possible, including the source, userid attempted, ip address etc.

  All comments and suggestions would be greatly appreciated!

  James

  Archives
  The config log
  Enable logging
  notify the contenttype in clear syslog
  hidekeys
  opening of session
  192.168.1.1 logging
  block connection-for 60 tent 3 within 60
  connection sur-Echec connect all the 1
  connection on success - open a session every 1

• Connection attempts that have failed maximum AnyConnect on the LDAP Windows database

  Hello

  I can't seem to find the setting for the Web and client Anyconnect set connection attempts that have failed maximum when on the LDAP in Windows database.

  I would say that after that maximum 3 attempts to connect the possebility to connect again times out for 10 minutes.

  Now it is possible to log in as often as you want, which is a big security problem.

  Please, I can use some help to achieve this, thanks in advance.

  Best,

  Orson

  I don't think that this can be configured in AnyConnect or on the ASA. They both rely on the settings on the Windows Server. We can fix this. (reference)

• Unable to connect error headset/Bluetooth Headset: the pairing attempt failed in an unknown error, is the reported error code: 0x80070005

  Original title: Bluetooth headset not connecting

  I have a Plantronics 9xxBackBeat headset, and I'm trying to connect my laptop (HP Pavilion dv6000)

  However, when pairing the headset I gives me the message
  "Device pairing failed.
  Matching attempt failed in an unknown error, is the reported error code: 0x80070005
  Contact the manufacturer of your device. »
  However, there is no driver for the 9xxBackBeat headphones and when I contacted their support, I'm referred my OS manufacturer, but when I talk about Microsoft, they tell me to go to Plantronics.
  Can someone tell me please how to fix this error?
  If it is not a mistake on the side of Plantronic, and if it's not a mistake on the side of Microsoft Windows, and then what happens?

  Hello

  1. are you able to connect other devices via Bluetooth from your computer?

  2 - is this compatible with your operating system device?

  First thing I suggest you to check the manual and if this device is compatible with your operating system.

  I suggest you try the steps mentioned below and check if it helps.

  Method 1: The problems with Bluetooth devices: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-problems-with-Bluetooth-enabled-devices

  Method 2: If the problem persists, then try to update driver:

  a. click the Start button.
  (b) in the search box type devmgmt.msc and then press ENTER.
  c. Select Bluetooth peripheral device and right click on it.
  d. now, select Update.
  e. restart your computer.

  Method 3: Also I suggest to add as peripheral to your Bluetooth computer and later check the required services running on your computer.

  Set up a Bluetooth device:

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Bluetooth-enabled-device

  Change settings for a Bluetooth compatible device:

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-settings-for-a-Bluetooth-enabled-device

  Hope this information is useful.

• Error: "connection attempt timed out, please check the connectivity of the internet" when trying to connect to Cisco AnyConnect 2.5 on Windows 7 x 64 computer with modem usb wireless HSIA.

  Original title: issue with Cisco AnyConnect 2.5 on win 7 x 64 when connecting to the internet using wireless HSIA usb modem.

  I have win 7 x 64 enterprize edition on my laptop.

  I have problems with Cisco anyconnect VPN client. When I'm on my corporate network it works fine.

  But when I connect to internet using HSIA modem usb wireless home form, client AnyConnect VPN will not connect. The error I get is "connection attempt has expired, please check internet connectivity.

  Please help me to solve this problem as soon as possible.

  Hi Manish,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet forums for assistance.

  I also recommend that you contact the VPN support to help:

  https://supportforums.Cisco.com/community/NetPro/security/VPN

• How to find the failed connection attempts at 'check' session is enabled

  How to find the unsuccessful connection attempt to dba_audit_trail when the "audit logon" is enabled.

  Filter your query against dba_audit_trail action_name = 'CONNECTION' with returncode! = 0 (returncode = 0 means that there are no errors - successful connection attempts)

• Monitoring VPN connection attempts

  I would like to be able to use the syslog messages that are detached from the ASA to monitor VPN connection attempts (successful or not). Looking at the posts system there are several codes that relate to this.

  I wonder if anyone has a good way to use syslog to do this? There are some codes that can be used for this information?

  Thank you.

  You can set the ASA to send syslog messages when the user connects and disconnects. There are a few types of 'remote access' as IPsec VPN, webvpn / without client anyconnect/ssl vpn client that you can follow.

  If you are using Clientless SSL VPN syslogs usually begin with 716xxx.  For example the syslog for connect is 716001 and disconnect is 716002.  There is a list of other Clientless VPN SSL related messages here. You can view the specific contents of each journal here:

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logmsg

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logmsgs.html#wp4776913

  If you use SSL VPN Client (SVC1.x, AnyConnect 2.x) syslogs usually begin with 722xxx. For example, the syslog for connect is 722022 and disconnect is 722023. There is a list of other customer VPN SSL related posts here

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logmsg

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logmsgs.html#wp4778697

  If you use the IPSec VPN client, you can follow a success to connect with 713119 (indicates the phase 1 completed), 713049 (indicates the complete Phase2) and disconnect with 113019. There is a syslog ipsec additional 713049 that you can follow for ipsec.

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logmsgs.html#wp4775678

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logmsgs.html#wp4775412 http://www.Cisco.com/en/US/docs/Security/ASA/asa80/System/message/logmsg

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logmsgs.html#wp4769539

  Here are some other notes to keep in mind:

  -You can tell that the logging levels you currently have on the command line ASA with 'show log '.

  -Newspapers that you send to a syslog server are controlled with the commands "Logging Trap". For example 'logging trap information' (level 6) or "trap alerts logging" (level 1)

  -You can tell what level of severity (i.e., alerts, critical, errors, warnings, notifications, informational, debug) each one connects through this link. As you can see by checking the link, those follow-up sign in or out as I've mentioned above are usually information (sev 6)):

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logsev

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/system/message/logsevp.html

  -If you want to create a specific subset of the syslogs to send to a specific device, you can do it with a class or a list of logging:

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/m

  For example (class log):

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/m

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/monitor.html#wp1065253

  class check vpnc informational FRT

  For example (list of logging):

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/monitor.html#wp1065512

  log list mylist message 722022

  log list mylist message 722023

  logging trap mylist

  Don't forget to evaluate the positions that helped you and to mark it as resolved if you question has been answered.

  -heather

• RTMPS connection delayed due to the direct connection attempt

  Hello world

  I have a big problem with the way the RTMPS connections are initiated in flash player.

  One of my customer network infrastructure does not allow direct connections to my server via port 443, but allows connections proxified (using the CONNECT method).

  The problem is that flash player expects the direct connection attempt to fail before trying the proxified... connection and on this direct infrastructure network connection timeout is 20 s (I can't change that).

  Users must wait for this time to connect to the server...

  Is there a way to tell the flash player do not attempt direct connection, or do not wait for this connection Timeout?

  Perhaps a directive in the automatic proxy configuration (.pac) file?

  I already tried every NetConnection proxyType values of parameter without success.

  Any help would be appreciated!

  You mentioned the 'CONNECT' method Have you tried "CONNECTOnly" that requires to initially use the default CONNECTION method and it is not always obey?

  Documentation on NetConnection.proxyType:

  Set the proxyType property before calling the NetConnection.connect() method.

  ...

  If the property is set to "CONNECTOnly", the player first attempts to use the CONNECT method. If this fails, there is no relief.

• Successive connection LDAP fails after the first LDAP authorization: with wrong password

  Hello
  
  I am currently integration Oracle CC & B utility to LDAP (Sun Directory Server java - SunOne), but I made a post here because CC & B delegates the task of authentication to the server Weblogic (I user WLS version 10).
  
  In Weblogic, I configured two authentication providers:
  1. the principal is the LDAP authentication provider (defined as optional control indicator)
  2. secondary education is the default authentication provider (defined as optional control indicator)
  
  Currently, some users of CC & B are stored in LDAP, and some other (more users system) are stored in the default authentication provider.
  
  To help you make the problem more clear, I did the test with followingscenario:
  1. user LDUser2 (stored in LDAP) login with correct passwrod-> success
  2. the sysuser user (stored in the default authentication provider) connect with incorrect password-> access denied (what is good and normal)
  3. the LDUser2 (stored in LDAP) user login with password-> successful OK
  4. the sysuser user (stored in the default authentication provider) connect with correct password-> successful OK
  5. the user (stored in LDAP) LDUser2 connect with the incorrect password-> denied access, which is normal. However, from this point, the problem starts
  6. the user (stored in LDAP) LDUser2 connect with the right password-> rejected access KO is the problem
  7. connection (also stored in LDAP as LDUser2) LDUser1 with the right password of the user-> big problem of access denied KO
  8. the LDUser7 user (stored in the default authentication provider) connect with the right password-> successful access
  9 restart the server resets the situation, but once a user is stored in the LDAP connection with a wrong password (5 point number), attempts by users stored in LDAP fail.
  
  It seems that after the first LDAP authentication with wrong password, all users stored in LDAP connection attempts will fail.
  
  Help, please.
  Thank you.
  
  Jeffry

  Hello

  The connection attempt is made on console weblogic with the same result?

  If I'm not wrong, until WLS 10.3 it is a problem reported where once the user connects with password and username incorrect, all attempts after that results in the failure of the connection.

  The patch is available with up to 10.3 WLS support

  This might be the question however need to check.

• Dynamic JDBC: account blocked after the single connection attempt

  Our database is set up so that user accounts are locked after 3 bad connection attempts, but they're getting locked after only 1 attempt. I would like that it so that any attempt to connect ADF would be only created an Oracle connection attempt.
  I use JDeveloper 10.1.3.4.0 and by default, right click and then run.
  
  Code of the not yet documented Steve Muench ADF application examples at http://blogs.oracle.com/smuenchadf/examples/#14
  which is also described in http://www.oracle.com/technology/products/jdev/howtos/10g/dynamicjdbchowto.html
  
  Looking at the audit trail, I see the database tries to connect 5 times than the user.
  Trying to debug, I see that the doFilter in ADFBindingFilter is also called 5 times.
  
  In my research, I read the proposals that it might be the framework that tries to connect several times. It depends on the connection pooling and application module pooling settings you have.
  But I tried searchign in JDeveloper and don't see not where I set or change anything on reunification.
  
  Thank you
  
  Jeff

  Oracle has finally acknowledged it is a defect of jdeveloper and entered
  Bug 9153659: JDBC DYNAMICS IDENTIFICATION ACCOUNT LOCKS AFTER 1 FAILED CONNECTION information
  And I have no idea how oracle reactive is subject of fixed bugs, but since the last version of jdeveloper 10 numbered fixed iin bugs 5 millions, I guess that this will never be corrected.

• "Connection server failed" constantly popping up on sites popular randomly and unable to use FF on Linux Mint 17.1

  As above, websites at random and many of those that I use, say "Connection server failed" and then I can't even go to the Web site. I use FF 35.01 on Linux Mint 17.1. This has never happened before... Pages work fine on another device or Chrome!

  I found my problem!

  I checked the link you gave me, but none of the error messages that are matched. So, I googled the error message, and he apparently had to do with the date of my computer. The date was one day! And what to do with some https sites... Here is how I fixed / solved my problem:
  http://www.genuinescope.com/blog/sec_error_ocsp_future_response/

  But thanks for helping me narrow my problem!

• I get a 'Secure connection' error failed with google stating "certificate contains the same serial number.

  When I click on a link to a google search, I get the "Secure connection" error failed in Firefox. He says, "please contact the administrator of the server or email correspondent and give them the following information: your certificate contains the same serial number for another certificate issued by the certification authority."

  I followed the instructions here:
  https://support.Mozilla.org/en-us/KB/certificate%20contains%20The%20Same%20serial%20number%20As%20another%20certificate
  and looked at this article:
  https://support.Mozilla.org/en-us/questions/1028103?ESAB=a & As = AAQ

  I uninstalled and reinstalled Firefox, deleted the entire folder profiles and reset Firefox. I see that the older (orphans) article points to my router. However, I have a new router and have updated their software. There is no button to add an exception (as stated in the article), so I can't just work around it. This problem does not occur with IE, so I have a hard time to believe that it is my router.

  How to solve this problem? I really want to change browser.

  Finally, I tracked the issue. The answer was found here:
  https://support.Mozilla.org/en-us/questions/1028985

  It turns out that Avast has a web shield that passes through its own verification of certificate https. Of course, this feature is not quite right and loses track of the certificates. Disable "https scanning" in the settings of Avast resolved the problem.