ASA secondary IP address configuration

Similar Questions

• VPN client with counterpart on secondary ip address on the public interface of the router

  Hello

  On our office LAN, we have a Linux server than it hosting a VPN connection to a remote client.

  Do this to ISAKMP card on our Cisco router port connections to the internal ip address of the Linux host.

  However, we now want to allow our users to establish VPN connections to our local network using the unit of Cisco VPN Client.

  Of course, this would present challenges, as the ISAKMP our router port is mapped through an internal host.

  So, we tried to set up a secondary ip address on the router and VPN clients to connect to that.

  What we see in our newspapers is as follows:

  Phase 1 is very well established, and the VPN Client prompts the user for a user name and password.

  Authentication of the phase 2 starts, but the router says it's is not to receive a proposal of hash of the client.

  185 12:18:06.943 09/03/11 Sev = Info/4 IKE / 0 x 63000014
  RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

  (in this case, where x.x.x.x is the secondary ip address on the public interface)

  After that, the Phase 1 SA is removed and the connection fails.

  My understanding is that the Phase 2 negotiation takes place with the ip address assigned to the client in Phase 1, which suggests that the problem occurs because the client communicates with the main on the interface ip address, and no secondary ip address.

  When remove us the mapping of port isakmp and the VPN client to connect to the primary ip address, everything works fine.

  Question:

  It is possible to establish 2 router VPN Client uses a secondary ip address?

  If not, is there some way I can implement the port mapping so that it occurs, the connection comes from a specific ip address?

  Garreth

  Should be supported on IOS.

  The command is crypto ctcp port...

  Check this link:

  http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6635/ps6659/prod_white_paper0900aecd8061e2b3.html

  Federico.

• ASA 5510 can be configured as bridge mode and always send Netflow information to a collector

  ASA 5510 can be configured as bridge mode and always send Netflow information to a collector?

  We have a PIX connect internal network to the internet. Because PIX does not support NetFlow, as temporary solution, we thought to a 5510 ASA between the PIX and the internet gateway and configure as a bridge so that there will be no problem routing, and the SAA can always send Netflow information to a collector.

  Can someone please advise if this is possible?

  Thank you.

  I have not tried, but as a Netflow service policy should work in routed and transparent mode. Reference.

  Why don't you just replace the Pix with the ASA in routed mode?

• Error message: Ethernet is not a valid ip address configuration and cannot connect to the Internet after installing Windows 8.

  Original title: Internet not working after installing Windows 8. Help, please

  I installed Windows 8 a week before, which had Windows Vista. When I was with Vista, I had no problem with the Internet, I had. But shortly after I installed Windows 8, the problem began. The connection is hardly 2 minutes. In addition, it is not navigate beyond my home page. After troubleshooting the result came as Ethernet is not a valid ip address configuration. It makes me really frustrated. After all, I was looking forward to navigate in windows 8, this problem makes me think really bad. If someone could help me, it will be grateful to you.

  Manorajan respected,

  I too had d same problem but I solved it later on myself.
  Here's how to: -.
  1-make sure you have intel network driver I installed your windows it pc. Download (on any other pc and transfer and install in it) and install it in your pc respective windows 8. Here is the link to download:-http://drivers.softpedia.com/get/NETWORK-CARD/INTEL/Intel-Network-Adapter-Driver-172-for-Windows-8.shtml
  Den DOWNLOAD realtek lan driver here to install http://drivers.softpedia.com/get/NETWORK-CARD/REALTEK/Intel-Realtek-LAN-Driver-80030730-for-Windows-8.shtml..if in the installation of theres no error ignore it... do not panic and reinstall... as it is already installed

  2 - unplug your LAN cable and Wi - Fi

  3 - go to network and sharing den center left side d click on change adapter settings clik left on the network card intel

  4-go to "Ethernet Adapter local area connection' properties and Deselect"Internet Protocol Version 6 (TCP/IPv6) "

  "5 - Select" ""Protocol Internet Version 4 (TCP/IPv4) '

  Press the properties button

  6 - Select "use the following IP address:" option and set this ips

  IP = "ip address".

  subnet mask = 255.255.255.0

  default gateway = your ip from the router (you can recheck all say on any other pc having a successful conection even wid tell by checking the properties of dial-up connection or any smart phone like any iphone or android mobile, if it is used as a wifi too in led staus/properties to your respective wifi name)

  7. in the second section select "use the following DNS server address:"

  Set "Server DNS PreferAlternate:" your router ip that entered u in "default gateway of" this. " pinterested ok and try to connect in wireless lan

• On ASA 5520 SSL certificate configuration

  Hello

  I have an SSL certificate from a third party that shows under the identity of ADSM, howerver analysis of verification of the firewall shows that the SSL certificate is signed with an unknown certification Authority. I installed through primary and secondary certificate from the third party under the authority of certification the SMDA but when I check the SSL certificate it still shows as self-signed. Don't miss what other measures. I have attached a few screenshots.

  Thank you for your help.

  Wo

  Hello

  You have activated the correct trustpoint in Configuration > device management > advanced > component settings SSL? On this screen, there a "Certificates" section where you can select the trustpoint appropriate for each interface.

  The trustpoint will reference the certificate that you imported, and the interface will reference this trustpoint. Until you activate, the ASA will continue to use the self-signed certificate.

  Hope that helps.

  -Mike

• ASA 5505 Split Tunneling configured but still all traffic Tunneling

  Hello

  I installed an ASA 5505 running 8.3.2 and Cisco AnyConnect Client 2.5.2017.

  There are the DefaultRAGroup and a newly configured Group called SplitTunnelNets.

  I have 1 internal subnet (192.168.223.0/24) which has a matching ACL/AS configured on the DefaultRAGroup and the custom group policy called SSLClientPolicy.

  When I start the VPN with the ASA, I can indeed reach internal resources, but when I look at the routing table, I see a new default gateway route 0.0.0.0 / 0-> 192.168.25.2 (that is in the IP pool) with a metric of 2.  The default route before the start of the session AnyConnect now has a higher metric, so the 192.168.25.2 next hop is a priority.

  I don't see the routes in the routing table for 192.168.223.0/24 as I expect to see.  In the diagnosis of AnyConnect, I see that 0.0.0.0/0 is the policy applied to the client.

  Here's my setup.  Please tell me if you see something that I'm missing.

  ASA 8.3 Version (2)
  !
  host name asa

  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.223.254 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP x.x.x.x 255.255.255.240
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  boot system Disk0: / asa832 - k8.bin
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS lookup field inside
  DNS server-group DefaultDNS
  Server name 192.168.223.41
  domain Labs.com
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  vpn-client-net network object
  255.255.255.0 subnet 192.168.25.0
  network of the internal net object
  192.168.223.0 subnet 255.255.255.0
  the DM_INLINE_NETWORK_1 object-group network
  internal-net network object
  network-vpn-client-net object
  the DM_INLINE_NETWORK_2 object-group network
  internal-net network object
  network-vpn-client-net object
  SplitTunnelNets to access extensive ip list allow any 192.168.223.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  mask 192.168.25.1 - 192.168.25.50 255.255.255.0 IP local pool SSLClientPool
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ASDM image disk0: / asdm - 635.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT (inside, all) static source internal-net net internal static destination vpn client vpn client-Net
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Labs-AAA protocol ldap LDAP-server
  AAA-server Lab-LDAP (inside) host 192.168.223.41
  Server-port 636
  LDAP-base-dn dc = labs, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn [email protected] / * /
  enable LDAP over ssl
  microsoft server type
  Enable http server
  http 192.168.223.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto ca trustpoint ASDM_TrustPoint0
  registration auto

  sslvpnkeypair key pair
  Configure CRL
  Crypto ca trustpoint ASDM_TrustPoint1
  ASDM_TrustPoint1 key pair
  Configure CRL
  string encryption ca ASDM_TrustPoint0 certificates

  Telnet 192.168.223.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 192.168.223.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  dhcpd outside auto_config
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP 192.5.41.41 Server
  NTP 192.5.41.40 Server
  SSL-trust outside ASDM_TrustPoint1 point
  WebVPN
  allow outside
  No anyconnect essentials
  SVC disk0:/anyconnect-win-2.5.2017-k9.pkg 1 image
  SVC disk0:/anyconnect-macosx-i386-3.0.0629-k9.pkg 2 image
  Picture disk0:/anyconnect-linux-3.0.0629-k9.pkg 3 SVC
  enable SVC
  tunnel-group-list activate
  internal SSLClientPolicy group strategy
  attributes of Group Policy SSLClientPolicy
  value of server DNS 192.168.223.41
  VPN-tunnel-Protocol svc
  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list SplitTunnelNets

  field default value Labs
  split dns value Labs.com
  the address value SSLClientPool pools
  WebVPN
  SVC Dungeon-Installer installed
  attributes of Group Policy DfltGrpPolicy
  value of server DNS 192.168.223.41
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list SplitTunnelNets
  coyotelabs.com value by default-field
  type of remote access service
  type tunnel-group SSLClientProfile remote access
  attributes global-tunnel-group SSLClientProfile
  CoyoteLabs-LDAP authentication-server-group
  Group Policy - by default-SSLClientPolicy
  tunnel-group SSLClientProfile webvpn-attributes
  allow group-alias CoyoteLabs
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:95b7ff58b54e02948a14b225eec1a990
  : end

  The split tunnel access list must be standard access-list, not extended access list.

  You must change the following:
  FROM: SplitTunnelNets access-list extended ip to allow all 192.168.223.0 255.255.255.0
  To: SplitTunnelNets standard access list allows 192.168.223.0 255.255.255.0

  You should be able to reconnect again and will be able to access the Internet after you set up the standard access-list split tunnel.

  Hope that helps.

• ASA 5520: SSL VPN by using a different IP address that the ASA public IP address

  Hi guys,.

  I'm trying to configure an SSL VPN on a Cisco ASA5520.

  Unfortunately port 443 interface OUTSIDE of the SAA is already used by Microsoft Outlook Web Access and I can not change the configuration of Outlook. This configuration already in place allows me to use the public IP address of the ASA as IP Cisco VPN for the Web page.

  I don't not want to use a different port so to keep life easy for users.

  I have a few available public IPs that I can use so I wanted to use one of them instead of the OUTSIDE of the ASA interface. Any idea how I could do?

  Thank you

  Dario

  Unfortunately you can not use any other public ip address, except the ASA outside IP interface to complete the SSL VPN.

  The only options that you have is to change the Outlook to use another port or the SSL VPN to use a different port.

• ASA 5525 X Anyconnect configuration with ISE 2.1

  I have a new deployment of ISE 2.1 which is used only for the management of the devices at the moment.  The intention is that it will serve as radius for authentication of our VPN server.

  5525 x is a brand new ASA runs the 9.4 code.  I want to configure VPN on the SAA strategy so that each user is assigned a DAP based on their Department.

  I already have the designation of the Department for user accounts assigned in AD through a group membership.  I don't know how to get ISE to belonging to a group at the ASA so that she can associate the user based on this correct in RAP group membership.

  I succumbed to determine how this is supposed to work.  Thanks for any help.

  @Jonathan Harrison ,

  Normally we authenticate and authorize users and then push DACL or allow connection from ISE etc. of such conditions profiles that check results Posture or parts constituting the identity of the user (such as AD or another external identity store belonging to a group).

  There are a couple of good guides to do so, including detailed examples:

  https://communities.Cisco.com/docs/doc-68158

  http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-app...

  http://www.Cisco.com/c/en/us/support/docs/security/AnyConnect-secure-mob...

  While they focus on the case of use of Posture, they can be adapted to add other uses. For example, ISE registration condition may be the result of not only a Posture check also membership in a given group or another if you make it a State.

  I do not think we can specify to the ASA to call a given font of DAP like Hostscan module cannot be used at the same time that the module ISE Posture. However, you should be able to accomplish just about everything you used to depend on the DAP with ISE Posture Module AnyConnect (assuming you have AnyConnect 4.x Apex licenses).

  If you want to stick with the ASA DAP model, you can forgo using policies and module ISE Posture and instead create an authorization profile (result) to send the ASA, a pair of RAY - V based on a correspondence (in the authorization of the ISE policy) with the ad group. He is a "Cisco-VPN-3000" A - V called "PIX7x-members-from' that can be used in ASA dynamic access policies. You can see (and all other pairs A - v supported buy ISE) here:

  https://communities.Cisco.com/docs/doc-67894

• ASA static IP Addressing for IPSec VPN Client

  Hello guys.

  I use a Cisco ASA 5540 with version 8.4.
  I need to assign a static IP address to a VPN client. I saw in the documentation Cisco that this can be done to validate the user against the local ASA and in the user account database, you assign a dedicated IP address, or using the vpn-framed-ip-address CLI command.
  The problem is that the customer never gets this address and it always gets one of the pool in the political group. If I delete this pool, the client can't get any address.
  No idea on how to fix this or how can I give this static IP address to a specific VPN client?
  Thank you.

  Your welcome please check the response as correct and mark.

  See you soon

• MMIC access without IP address configuration. and without having to reboot.

  Hi all.

  Am Yoong.

  I have question for access MMIC.

  In my customer's site, there is a UCSC-M240 server.

  I need to access the CIMC, there is no ip to the MMIC server configuration (maybe we by default)

  I know I should confugration IP of CIMC for UCS restart server, but it may not.

  Because of the desires of the customers.

  How can I access MMIC and get the log file of technical support without setting address IP MMIC?

  Is it possible to configure the IP address on the server?

  Kind regards.

  Yoong huh.

  Yoong,

  If the configuration by default MMIC has DHCP then probably he waits for the server switch DHCP to assign an IP address to it.

  Please go ahead.

  Kind regards

  Saurabh

• How to set the Satellite Pro M10 screen as secondary in a configuration double monitor?

  I tried to use the laptop as a secondary display screen in a dual monitor Setup, but I can not change in display properties. To choose an external monitor like main screen is grayed out. Only option is to use the external monitor as a secondary screen or a clone, but this isn't what I want.
  I tried the things:
  * Laptop computer in a docking station
  * Update the video card drivers
  * Use UltraMon

  Any ideas on that?

  Hi Steen

  Can you please tell me what model of laptop you have? Is this other older or the new brand? As much as I know this option is not available on all Toshiba laptops. On my Tecra I'm not able to use this option, but I know with certainty that on some cell phones, something like this is possible.

• static, lwapp AP ip address configuration

  Is it possible to set the static ip address to lwapp AP? If I changed the ip address of management controller, lwapp AP is not discover and join the controller without DHCP server. right?

  I tried to put the IP lwapp AP by the console, but failed. Is a good idea?

  Hi Yong,

  If you flash sh: you will see a file VAR_ENV. can you try deleting this file and try entering the same command once more.

  Kind regards

  Ankur

• the source for copy tftp address configuration

  Hello

  on cisco, I can define the interface source for tftp transfers.  I can do this on 8024f? or 8132F

  Here are the valid destination URL

  TFTP: / / {IPAddress | hostname} / path/file name
  {SCP://{User@ipaddresss | hostname} / path/file name
  {sftp://{User@IPAddress | hostname} / path/file name
  Flash://filename
  USB://filename/filename

  There is no option for a specific interface.

• Help address IP PIX

  How many subnets can I connect to an interface of a PIX?

  Each interface of a PIX may have one and only one IP address are entrusted to him. This isn't a router that can have multiple secondary IP addresses configured.

• address of the loopback interface or sencondary in ASA

  I have a problem with Server Load balancing feature for firewall load balancing. If want to achieve this, we create an address of the loopback interface or secondary ip address in TWO firewalls (ASA). using hurried SLB mode... Can anyone suggest how this can be accomplished.

  Loopback interface cannot be configured on SAA. For load balancing on refer to the URL

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805fda25.shtml