static, lwapp AP ip address configuration

Similar Questions

• ASA secondary IP address configuration

  Hi Experts,

  Is it possible to configure a secondary IP address in external interface? My need is... my client ISP's going to change. For the migration, so I need to connect to the external interface to the new ISP. If I can set a secondary IP address to the external interface, there is no downtime at all... I searched for this. But I did not have a valid solution. Could someone please help?

  concerning

  Vipin

  No, unfortunately ASA interface does not support the secondary IP address configuration as in router IOS.

  Unfortunately you will not be able to have zero to download when you change ISPS.

  Do not forget also to change the following:

  -ASA outside interface to the new ISP subnet

  -Default route for external interface

  -All the NAT will be replaced by the new addresses of the ISP

  -All the DNS resolution as appropriate to the new address ISP

  -All the ACL will be replaced by the new addresses of the ISP

  -Also notified all of your change of address ISP VPN peers.

• Error message: Ethernet is not a valid ip address configuration and cannot connect to the Internet after installing Windows 8.

  Original title: Internet not working after installing Windows 8. Help, please

  I installed Windows 8 a week before, which had Windows Vista. When I was with Vista, I had no problem with the Internet, I had. But shortly after I installed Windows 8, the problem began. The connection is hardly 2 minutes. In addition, it is not navigate beyond my home page. After troubleshooting the result came as Ethernet is not a valid ip address configuration. It makes me really frustrated. After all, I was looking forward to navigate in windows 8, this problem makes me think really bad. If someone could help me, it will be grateful to you.

  Manorajan respected,

  I too had d same problem but I solved it later on myself.
  Here's how to: -.
  1-make sure you have intel network driver I installed your windows it pc. Download (on any other pc and transfer and install in it) and install it in your pc respective windows 8. Here is the link to download:-http://drivers.softpedia.com/get/NETWORK-CARD/INTEL/Intel-Network-Adapter-Driver-172-for-Windows-8.shtml
  Den DOWNLOAD realtek lan driver here to install http://drivers.softpedia.com/get/NETWORK-CARD/REALTEK/Intel-Realtek-LAN-Driver-80030730-for-Windows-8.shtml..if in the installation of theres no error ignore it... do not panic and reinstall... as it is already installed

  2 - unplug your LAN cable and Wi - Fi

  3 - go to network and sharing den center left side d click on change adapter settings clik left on the network card intel

  4-go to "Ethernet Adapter local area connection' properties and Deselect"Internet Protocol Version 6 (TCP/IPv6) "

  "5 - Select" ""Protocol Internet Version 4 (TCP/IPv4) '

  Press the properties button

  6 - Select "use the following IP address:" option and set this ips

  IP = "ip address".

  subnet mask = 255.255.255.0

  default gateway = your ip from the router (you can recheck all say on any other pc having a successful conection even wid tell by checking the properties of dial-up connection or any smart phone like any iphone or android mobile, if it is used as a wifi too in led staus/properties to your respective wifi name)

  7. in the second section select "use the following DNS server address:"

  Set "Server DNS PreferAlternate:" your router ip that entered u in "default gateway of" this. " pinterested ok and try to connect in wireless lan

• WRT54G static assignment of IP addresses?

  Hello everyone, I have a WRT54G v4 (FW 4.21.1) router wireless and I am trying to configure to assign static IP addresses to my devices.  I have two wired devices, and seven wireless devices and IP addresses are constantly evolving. This is normally no big deal, one of the wired devices is my printer (connected via a cable etherner). The only way I can install this printer to devices is to a standard TCP/IP installation, using the IP address assigned automatically. My question is, can I assign one address of the printer so that I can install it on the rest of devices with an address? Or do I have to assign an address to each machine? And how even statically assign? I know how to connect on the router and am familiar with the integrated navigation page, but I do not see a table of MAC addresses anywhere. I have the latest firmware as well. Thank you in advance for the answers!

  The WRT54G does not support a DHCP reservation. You set a static IP address on the printer. I have not heard a network printer on which you cannot set a static IP address...

• static routes - PIX outside address

  I tried to get a configuration (PIX501) which allows inside customers access to the outside and also allowing outside access to a smtp mail server in-house. From what I tried, it seems that I can't use the external IP address of the pix for the static control (indoor, outdoor). If I do other client access to the outside world is denied.

  So far I couldn't find any documentation about it. Can someone point me in the right direction plse?

  Hi morris,.

  I Don t know what the other guys are talkin´about, but it seems to me that they do not exactly understand your question and provide you with wrong information.

  In my opinion you want to translate all your inside source of addresses to the address of interface outside. It is already well configured, I saw in your config file. Indeed, these two commands are correct:

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  What bothers you is you want your mail server to be accessible from the outside to the inside for SMTP. The command you tried is:

  public static interface (inside, outside) MyServer netmask 255.255.255.255

  And it does not work.

  The command you need is the following:

  public static 25 25 MyServer netmask 255.255.255.255 interface tcp (indoor, outdoor)

  This static creates the translation for tcp port 25 (smtp) outside address to port 25 of your inside the server interface.

  I advice lets you modify the line "access-list permits outside_access_in tcp any any eq smtp" in "outside_access_in of the list of permitted access tcp any host 209.164.3.5 eq smtp".

  Put all together, modifications, you must perform:

  not static (inside, outside) interface MyServer netmask 255.255.255.255

  public static 25 25 MyServer netmask 255.255.255.255 interface tcp (indoor, outdoor)

  no access list outside_access_in not allowed tcp any any eq smtp

  outside_access_in list access permit tcp any host 209.164.3.5 eq smtp

  Finally make a clear xlate and it will work.

  Best regards and good luck,

  Leo

• MMIC access without IP address configuration. and without having to reboot.

  Hi all.

  Am Yoong.

  I have question for access MMIC.

  In my customer's site, there is a UCSC-M240 server.

  I need to access the CIMC, there is no ip to the MMIC server configuration (maybe we by default)

  I know I should confugration IP of CIMC for UCS restart server, but it may not.

  Because of the desires of the customers.

  How can I access MMIC and get the log file of technical support without setting address IP MMIC?

  Is it possible to configure the IP address on the server?

  Kind regards.

  Yoong huh.

  Yoong,

  If the configuration by default MMIC has DHCP then probably he waits for the server switch DHCP to assign an IP address to it.

  Please go ahead.

  Kind regards

  Saurabh

• the source for copy tftp address configuration

  Hello

  on cisco, I can define the interface source for tftp transfers.  I can do this on 8024f? or 8132F

  Here are the valid destination URL

  TFTP: / / {IPAddress | hostname} / path/file name
  {SCP://{User@ipaddresss | hostname} / path/file name
  {sftp://{User@IPAddress | hostname} / path/file name
  Flash://filename
  USB://filename/filename

  There is no option for a specific interface.

• Assigng WRT54G a static IP address

  I recently bought a new WRTG54G2 to replace an old one that died.  I'm trying to set up as the former, but without access to the configs I don't know exactly how I've done it before.  Here's what I have.

  Cable modem--> (192.168.0.1) dedicated firewall/gateway Machine--> switch--> other equipment (for a Visual, you see this link )

  Other equipment is wired to the PC and the wireless router.   The wireless router needs to assign a static IP address of 192.168.0.50.  It must go through the dedicated firewall/gateway (192.168.0.1).  The DHCP Service will be switched off.

  I know that it is possible, however, for the life of me... I can't understand how I've done it before.  In the web interface, I can assign staticlly wireless router an ip of 192.168.0.50 via the automatic configuration (DHCP).  But, if I go to the static IP address configuration, replace the IP 192.168.0.50, it won't work (that is to say, the only "static ip" is the local IP address under Network Setup/router IP).

  Any suggestions for how I can do this?  It makes me nuts to be able to access only the web interface page.

  Thank you muchly

  Jon

  And I managed to solve my problem by following the steps at this site.

• Static NAT configuration

  I have VMWare with Windows 2012 R2 VM installation.  I am installing the VM to have a static NAT (DHCP disabled) address and connect to the internet.  I can't understand why it doesn't work for me.  The virtual computer can connect to the internet fine with DHCP active, but once I change to static, using the same IP addresses, it stops working.

  I have modified the virtual network Editor to use a specific subnet and disabled DHCP

  

  Changed the settings for the TCP/IPv4 virtual machine to use a static address

  

  The only thing I noticed is that the host NIC for VMnet8 continues to change its configuration to default.  Even if I change it to the new subnet that he shouldn't come back to 192.168.21.0.

  I tried many different types of configurations, but I can't understand exactly what I'm doing wrong!  This guide of VNE was not very helpful and many other resources did not help much either.

  try to manually configure DNS settings in advanced NAT settings option and check again

• Ethernet on external device with static IP address

  I'm trying to connect my external station of development (Visual Studio in Windows XP/Fusion on my Mac) for Windows CE device through an ethernet cable crossed for the CE - device debugging.

  This forces me to set a static IP address on the external device and the development station.
  Both must be on the same subnet. How can I do this?
  I tried to use the Bridged (ethernet) mode on the network card and set up a static IP address in windows XP. I also created another static IP address in OSX. Looking at the IP/ethernet side traffic OSX (using Wireshark), messages from the external device IT appears, but glancing Wireshark in merger/Windows XP, I don't see them.
  Am that I on the wrong track here with the Bridged mode?

  First of all you shouldn't have to use a crossover cable as Ethernet adapter of the Mac must Auto-Sensing and automatically process the cross above a straight through cable. (At least this is so on my Mac.)  Secondly, I would not give the host a IP road-able and only set the IP in the - CE device and virtual machine with no gateway/DNS IP address. When you use a NIC jumpered in the Virtual Machine.

  On the host if the Ethernet adapter using DHCP then you will have to wait for it to expire and get a 169.254.0.0/16 address IP or if you want an answer more quickly then manual assign a 169.254.0.0/16 IP address for the host's Ethernet card.  In this way communication is directly between the - CE device and virtual machine using VMware Bridge Protocol.

  If you do what the host itself to have connectivity in this loop, then of course assigns an IP address appropriate with no gateway/DNS IP address.

  Example of IP address Configuration

  CE-IP address: 192.168.3.1/24

  Address Virtual Machine IP: 192.168.3.2/24

  The IP address of the host: 169.254.0.0/16 or 192.168.3.3/24

  No gateway/DNS on any IP address.

• Where to configure the SCAN address?

  Hello
  
  I'm in the middle of the installation of the cluster of grid infrastructure for Oracle 11 g 2 RAC on AIX 6.1
  
  I had defined the public IPs, IPs private and interconnections in the files DNS and hosts. I do not use GNS because we use static IP, no DHCP address.
  
  during installation, I will ask you the address IP SCAN, I prepared and resolved by the DNS, but I don't know where the configuration
  
  SCAN IP address is not the ping requests but can be lookedup and I get the answer that he
  
  When I put it, in the switch in a Rack or will I choose different installation method.
  
  Kindly advice
  
  Kind regards
  C.

  whatever Rajesh mentioned URL. I think it's the perfect way to set up.

  For the time being you can tent to configure only a single IP SCAN address in the file/etc/hosts in all nodes of the Cluster and try to move forward.

  That very sure, it won't ping until the Configuration of the grid is not complete.

  Sumit-

• How to configure an ip address reversed in exchange server 2003

  some my users have rebounded for them because there is no Ip address configuration reversed in Exchange for mail.

  Is there a step by step set up?

  Thank you for visiting the Microsoft Answers site. The question you have posted is related to Windows Server 2003 and would be better suited to the Windows Server TechCenter community. Please visit the link below to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

• Failed to get printer email address on Officejet Pro 8500 a A910a

  Hi HP Support!

  I would like to know how I can get the e-mail address of my printer? My printer model is HP Officejet Pro 8500 A910a. Here's my current installation of the printer:

  1. I've already updated its firmware to include the eprint service.
  2. My printer is already connected to the internet via the wireless network connection.
  3. I am able to print documents using the wireless printing functionality.

  Everything is already OK, except that I can't use the print feature Email Address. Whenever I click the button, it says 'the printer could not connect to the server' (note that I have already activated my Web Services printer). He also says that I need a parameter to connect to the printer of proxy server.

  That's my problem. I already looked for my proxy and there is none. I tried to watch using my Firefox browser and the browser I.E via internet options. I even googled 'what is my proxy setting' and the result says 'no proxy server detected' just my IP address.

  Please help me with this. Thank you!

  Hello

  The steps below a usually resolve the problem you are experiencing:
  
  1. unplug the power cord at the back of the printer.
  
  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).
  
  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.
  
  4. wait for 30 seconds, then plug the printer back and power.
  
  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.
  
  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):
  
  1. tap the wireless at the top of the screen of the printer and note the IP address.
   
  2. Enter the IP address in the address bar of a web browser on a computer and press on enter or click the go button browser.
   
  3. the printer status page must be open.  Click network in the upper part.
   
  4. click on networking on the left.
   
  5. Select the Proxy settings.
  Note: If you are prompted for a redirect, click OK.  If you receive a certificate warning, select the option that allows you to continue anyway.
  If you receive an internal system error, refresh the page until it loads the proxy settings.
   
  6. check that all fields are empty.  If they are not, make them disappear and make sure that the Proxy Server requires authentication is unchecked and click on apply.  You should get a success message.
   
  7. click on the network address (IP) on the left.
  Note: If you only configuring IP address and DNS address with a yellow note Configuration, refresh the page until it loads completely.
   
  8. leave automatic IP IP address Configuration.
   
  9 change the DNS address to the manual DNS Server Configuration.
   
  10. enter manual for the manual preferred DNS Server 8.8.8.8 and 8.8.4.4 for auxiliary DNS.
   
  11. click Apply and you should get a success message.
   
  12. turn off the printer for 30 seconds and then turn it on again to force the new settings take effect.

• 9792 Configuration Error OR

  Hello
  I am a new Member on these forums, I need help with the configuration of the gateway NI 9792.
  First of all, my gateway powered and not in secure mode, the status light will blink twice, I read the factsheet, which implies that the gateway software has an error. Not how to fix the error.
  I managed to configure the IP address of the gateway, but the device is not recognized on remote systems. I use the Ethernet 1 port for these tests.

  If someone could help me with this problem please.

  Thank you for your attention.

  Hello there;

  Therefore the NI 9792 is a remote controller; It will blink twice because that there is no software installed in the system, I recommend to format, set a static ip address, and then install the appropriate software. Don't forget that when you change address IP your PC must be in the same subnet as the device of the RT and you do you need to connect using a crossover cable.

  In order to start using it, it must follow the following process:

  0 check that you installed LabVIEW, NI WSN and LabVIEW RT in your computer

  1. make sure that all the DIP switches on your CompactRIO controller are in the OFF position.

  For DIP switch that switches from left to right, put it on the OFF side.

  2 disable network interfaces secondary, such as card access wireless on a laptop computer and disable your firewall

  3. set the DIP switch; Safe Mode, IP Reset and No App to position IT and restart the device

  4. Expand remote systems

  5 right-click the NI 9792 and select format the drive. This will define the IP address of 0.0.0.0 and formats throughout the system, it may take a few minutes until what you see under devices and interfaces.

  6. change the device IP address to static and the IP address you of the PC to get on the same network. (Control Panel > Network & Sharing Center > Local Area Connection > properties > Internet Protocol Version 4 > properties > set an IP address and the subnet.) Don't forget to put all dip switches to OFF

  7 install the software. Expand the CompactRIO item under remote systems, right-click on the element of software and select Add/Remove programs. Under the version in time real LabVIEW you want, select the OR RIO set currently installed on the development computer. Select the set Add ons software you want to install. Support NI Scan Engine can be selected from this menu.

  There is a guide for the cRIO here, it works exactly in the same

  Good luck

• printer change ip address removed ePrint account cant get back from work

  Photosmart Premium C410 fine woking with e-print. I had to change the IP address and also forgit r = the email address, I want to just start over. I logged into my account eprint and removed the printer. I disabled the webservices on the printer. Now I can not yet enable web services on the printer. Every time I try it tells me that it cannot connect to the server. It is connected wireless and an excellent resistance and printing from PC works fine. I tried resettimng to factory default on the printer, but no change. How to reset a new IP address to an e-printer e-mail address and/or how to enable web services again on the printer?

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. press the network icon at the top of the screen of the printer and note the IP address.
   
  2. Enter the IP address in the address bar of a web browser on a computer and press on enter or click the go button browser.
   
  3. the printer status page must be open.  Click network in the upper part.

  4. Select the Proxy settings.
  Note: If you are prompted for a redirect, click OK.  If you receive a certificate warning, select the option that allows you to continue anyway.
  If you receive an internal system error, refresh the page until it loads the proxy settings.
   
  5. check that all fields are empty.  If they are not, make them disappear and make sure that the Proxy Server requires authentication is unchecked and click on apply.  You should get a success message.
   
  6. click on IPv4 under the good (wired or wireless) connection on the left.
  Note: If you only configuring IP address and DNS address with a yellow note Configuration, refresh the page until it loads completely.
   
  8. leave automatic IP IP address Configuration.
   
  9 change the DNS address to the manual DNS Server Configuration.
   
  10. enter manual for the manual preferred DNS Server 8.8.8.8 and 8.8.4.4 for auxiliary DNS.
   
  11. click Apply and you should get a success message.
   
  12. turn off the printer for 30 seconds and then turn it on again to force the new settings take effect.