Beyond the limits of voltage on USB 6008?

Similar Questions

• How stable is the long term outputs analog USB-6008?

  The USB-6008 datasheet do not specify the stability long term of the analog inputs and outputs.

  I'm looking for stability compared to the ambient temperature and time (several months to a year), mainly for the outputs or the D/A reference voltage.

  Is there any information available?

  Thank you.

  The precision specification takes into account the evolution both because of the temperature and duration (stable).  Thus, for the period of a year that we guarantee these specifications, which list you is correct.  However, apart from the period of one year since the calibration, this specification may be is more inaccurate.

• What happens if we go beyond the limits?

  Hello...
  I want to ask doubts about the limits of the intellectual property of our Xperia family...
  Sony means said he did not overwhelm their devices under water for more than 1.5 meter... And for 30 minutes...
  So I want to ask that would happen if we go beyond 1.5 meter (ex 5-6 meters)... ? Fact our unit has a sensor to know that his goes beyond 1.5 meter?
  2. also, I want to know it is 30 min duration is related to the submerged depth (keep 1.5 m for 30 min)... Or otherwise you can not keep the unit more than 30 minutes even in shallow submerged water?... This is also where any sensor?

  It there any sensors that will tell if you went beyond 1.5meters whether you left your phone longer than 30 minutes, but the water will be disclosed in ultimately damage your phone.

• Measures of true bipolar voltage with USB 6008/6009

  The 6008 or 6009 to make true bipolar (positive and negative voltages referenced to GND) measurements?  If not, what is the solution to purchase cheaper data this feature?

  Thank you.

  The question of unipolar vs bipolar vs bipolar Pseudo-aleatoire also was mentioned in this thread.  The 6008 6009 use bipolar-only mode and load the setting differential input or CSR.  Please note that {unipolar / bipolar / Pseudo-bipolaire} is independent of {differential / CSR / Pseudo-differentiel}.

  The 6008/6009 don't use 'Pseudo-bipolaire', which means that each differential input should be positive with respect to the ground.

  Best regards

• The cursor position can go beyond the limits when programmed with change of position

  I have the VI joint that has 2 buttons on it to move the cursor right and left of an increment when pressed.  (The code works when I replace with another chart of mixed signals with the same data as this one).  For some reason, the cursor will move beyond 608 to 613 to the right and the left.  I have the shows all the parcels market, but it doesn't seem to affect the thing.   Any ideas as to why this is happening?

  I have not studied in detail what is happening in your case, but as the sliders are locked in patches, it seems more reasonable to use the property "cursor index. It sets the index position of the table data where the cursor is locked. Seems to work very well (and without all this only convoluted songs and dances with cursor lists and names of labels).

  Try this:

  

  (I also highly recommend to stay away from coloring Easter egg from the diagram. A Boolean is hard to see on a green background. There is not a single background color that does not interfere unless a color yarn. Don't try to be cute, to focus on the task of encoding instead.

• AO. MaxRate, AO. MinRate, AO. Properties of voltage. RNGs for hardware DAQ USB-6008

  Hello

  in one of my report, I use the AO. Property of Voltage.Rngs to see if the selected DAQ card takes in charge the application voltage range. This works very well for my PCMCIA card as well as a PCI card. Now run the same VI with a USB-6008 device, this property gives all the return values. In addition, the report of AO.max.rate and AO.min.rate of the '0', the output is-200197 error properties. I use DAQmx as it is supposed to support the same functions for all DAQmx devices. Can someone please tell me what wrong here and how can I get around this?

  Best regards

  Gabs

  AO.min.rate and AO.max.rate are 0 and error-200197 back because the USB-6008 case supports the outputs analog hardware timed.  The description of error is "device does not support this property."  There is an entrance to the knowledge base for this question.

  By selecting 'Use Waveform' uses the synchronization of the sample clock.  The waveform data type specifies a delta t, which is used to set the sample clock frequency.  It is not supported on the box USB-6008.  You shouldn't set your calendar of sample type or explicitly assign the "On Demand".

  The DAQmx driver supports hundreds of different devices.  Not all combinations of properties are valid for all devices.

• fiber optical sensor su19 110 115 a 126 vs nor usb 6008

  Hi expert... I am looking for idea or help on my project. I try to get the measure of mention nor USB 6008 sensor output. In fact, I'm new with nor peripheral usb n still study n the search on internet or n. forums I found an idea to connect the sensor by aoi, but I can't seem to get a measurement any. Is the sensor can connect directly to the device usb or need some custom wire diagram between them. Thanks in advance

  First of all, it is useful if you name the manufacturer of the sensor. A single part number means nothing to most of us.  You use the sensor fiber-optic Pepperl + Fuchs? Even better is to display the technical/manual plug of the sensor or links to them.

  The data sheet that I found for the sensor to Pepperl + Fuchs is not very well written, in my opinion. It seems that the outputs are impulses with dependent amplitudes of the voltage and the frequency or the timetable set by the mode of operation.

  If it's the device you use, the only way you have any possibility to decode the outputs with the USB-6008 box is to measure with an analog input and then process the data in the software. According to the supply voltage, you will probably need a voltage divider to reduce the output voltage of the sensor to a level compatible with the DAQ hardware.  You also won't be able to use the high speed of the probe because the heart rate exceeds the Nyquist limit. In standard mode, you mighte be OK, but you can use a single channel of the USB-6008 to stay in the Nyquist limit.

  Lynn

• NEITHER USB-6008 outputs in series to generate 10 V

  We wonder if it is possible to connect the AO0 the AO1 as a series voltage source that generates 5 + 5 Volts?

  The datasheet is not say, do or not, but he says they are independent.

  Worst case being short, one of the outputs short-circuit if the ground is common?

  http://forums.NI.com/T5/Multifunction-DAQ/how-to-combine-two-analog-output-voltage-from-USB-6008/TD-...

• DAQ USB-6008 will be able to power and record voltage for UMS T5 blood pressure at the same time?

  I would use my NI USB-6008 to power my blood pressure monitor UMS T5 (http://www.ums-muc.de/en/products/tensiometer/t5.html) but also to take readings of it, but I don't know if it's possible to do it properly. The power supply for the instrument can be as low as 5V, I can easily get the dedicated + 5V channel. I'm able to feed the instrument and connect it to an analog input on the 6008 and measure a voltage in differential mode. However, when you read the documentation of support for the instrument, I find the following:

  "Potential pitfalls of data acquisition: the pressure transducer is configured in a full Wheatstone bridge, the input voltage and mV signal output can be connected to the same reference (mass)." Therefore, the mV output signal can be measured using a differential voltage measurement. Therefore, do not make an asymmetric measure of pressure transducer mV output. "(http://www.decagon.com/assets/Uploads/MeasuringUMSTensiometerswithnon-UMSControlandDataAcquisitionSystems.pdf)

  My understanding is that the 6008 can take a differential measure if I attach the signal '+' and the signal "-" to the analog inputs of positive and negative terminals. However, it seems that all the ports of ground on the 6008 are grounded to the same reference, which would make my measure of invalid tension according to the above paragraph. So my real question is: if I try to record the voltage with one of the analog inputs on the 6008 in this way, is the valid measurement? Or I need to find a separate power supply, with a different reference field to ensure that the measure is accurate?

  The technical details of this device is very poor. The manual is not much better. Companies that want to sell scientific equipment should publish decent cards or get out of business.

  In section 3.4.3 General requirements the device is described as a "bridge not amplified circuit.  This information along with the impedance of the bridge should be in the specifications, because it is essential to apply the device under any circumstances other than the nominal behavior in 10.6 V.

  The answer to your question is:

  You can use it with the box USB-6008.  The 5 V supply will result in output voltages a little less than half (5/10.6) the voltage specified in nominal conditions. You can use the differential input mode on the box USB-6008.  The absolute input voltages will be approximately 2.5 V with the 5 V power supply. This voltage is in the range of the aircraft. The differences are likely to be less than 100 mV. The resolution of the USB-6008 on the + /-1 V is located about 0.5 mV so your resolution of pressure will be about 1% of full scale. The voltage input impedance and termination of the USB-6008 will present a few errors.  These can be in the order of 5 to 10%. I can't predict much better without the missing bridge impedance specification.  These errors should be relatively constant and systematic. A calibration of the whole system - sensor and together hardware DAQ should allow you to compensate for a large part of this error.

  Lynn

• USB 6008 weird analog voltage reading

  Hello

  I use the USB-6008 to measure a voltage of a Lithium battery, 3.66V.

  the battery come with a blocking diode (in series with the battery) of 1N5820, who have a fall of voltage drop of 0, 1V.

  battery with diodes in series (this is the way in which the battery is shipped with)

  -measure with DDM yield 3.66V without you connect to usb6008

  -measure with DDM yield connected to usb6008 (putting OUT VOLTAGE USB6008) 3.59V

  -able with USB-6008 performance 3.59V connected to usb6008

  battery with diode removed

  -measure with DDM yield 3.66V without you connect to usb6008

  -measure with DDM yield connected to usb6008 (putting OUT VOLTAGE USB6008) 3.66V

  -able with USB-6008 performance 3.66V connected to usb6008

  Thus, it seems that the problem is in the led in the series.  This is why the battery voltage has fallen to 0.07V? the series diode will hurt the USB-6008?

  Maybe people who know the circuits inside the USB-6008 can give me an answer.

  Thanks in advance.

  Hi learnerd,.

  The fall that you see is falling forward in the diode.  As an entry class device, the USB-6008 case has a relatively low input impedance (144kOhm) and thus draws a little current of the device.  Looking at the datasheet of the 1N5820 (http://www.onsemi.com/pub_link/Collateral/1N5820-D.PDF), Figure 7 shows that at 25 ° C, a draw of 50mA will cause a fall front of 200mV.  While the figure does not extend the curve below 50mA, extrapolating the given curve would indicate that a drop of 70mV would cause only a few current microamperes.

  A DMM will have a much greater input impedance (GOhms instead of kohm) and won't draw enough current to influence the measure, that's why you wouldn't see the decline with only the DMM.

  The diode will not harm the USB-6008 somehow.

  Good luck with your application,

  The f

• NEITHER USB 6008 voltage offset using CSR and measurement of diff.

  Hi all

  I am currently trying the NI USB 6008 housing and I'm getting problems when reading voltage analog using CSR or differential.

  So basically, what I want to measure is a PWM signal (0 to 12V), which is divided by a divisor of tension (by two). But instead of measured 0V and 6V

  I am in a position a constant 0.8V and approximately 3V.

  On the side of digital data acquisition, I give you on impulses for the SSR... and it works fine.

  I connect it that way: http://digital.ni.com/public.nsf/allkb/95CC0CB11D7DF3D18625712E000C4ABD?OpenDocument

  Would apreciate any help

  Best regards

  EDIT: Attached graphics acquired are

  What is the impedance of your voltage divider?  The input of the USB-6008 impedance is not very high. If the impedance of the partition is large, it could cause the effect you see.

  Lynn

• Want a ramp of output voltage over time and measure input 2 analog USB-6008

  Hello

  I want to produce an analog voltage output signal that increases over time with a certain slope, which I'll send in a potentiostat and at the same time I want to read voltage and current (both are represented by a voltage signal) that I want to open a session and ultimately draw from each other. To do this, I have a DAQ USB-6008 system at my disposal.

  Creation of the analogue output with a linear ramp signal I was possible using a while loop and a delay time (see attachment). Important here is that I can put the slope of the linear ramp (for example, 10mV/s) and size level to make a smooth inclement. However when I want to measure an analog input signal he's going poorly.

  To reduce noise from the influences I want for example to measure 10 values for example within 0.1 second and he averaged (this gives reading should be equal or faster then the wrong caused by the slope and the linear ramp step size.) Example: a slope of 10 mV/s is set with a 10 step size. Each 0.1 s analog output signal amounts to 1 mV. Then I want to read the analog input in this 0.1 s 10 values)

  Because I use a timer to create the linear ramp and the analog input is in the same loop, the delay time also affects the analog input and I get an error every time. Separately, in different VI-programs (analog input and output) they work fine but not combined. I searched this forum to find a way to create the ramp in a different way, but because I'm not an experienced labview user I can't find another way.

  To book it now a bit more complicated I said I want to measure 2 input analog (one for the voltage of the potentiostat) signals and one for the current (also represented by a voltage signal) and they should be measured more quickly then the bad of the analog signal. I have not yet started with because I couldn't read on channel work.

  I hope someone can help me with this problem

  An array of index. You want to index the columns for a single channel.

• USB-6008 LABVIEW 8.2. SINGLE CHANNEL WITH DBL INPUT VOLTAGE OUTPUT COMPARISON

  I AM WRITING A PROGRAM THAT USES A SIMPLE USB-6008 ANALOG INPUT CHANNEL. I WANT TO READ CONTINUOUSLY THE VOLTAGE FOR 60 SECONDS. I WANT TO COMPARE A TENSION FOR THE PREVIOUS OF THIS SAME CHANNEL VOLTAGE, MAINLY FOR THE PERIOD OF TIME MAX VOLTAGE GIVEN, THEN GET A FINAL VOLTAGE READING. THE OUTPUT OF THE VI IS A DBL. I WANT ONLY TWO TENSIONS OF EXPORT TO EXCEL. TO SAVE TIME, I KNOW HOW TO EXPORT. CAN SOMEONE HELP ME WITH THIS ONE.

  VI needs an register shift related to the Max & Min function. The current value would be the entrance is and the entrance of x is the left shift register. The max value gets wired for the shift register to the right. Don't forget to initialize it. The output of the shift register is the max you would write and the value of the DAQmx Read out of the loop of wire will give you the last reading.

  Your waiting for 45 seconds makes no sense since you said that you wanted to read continuously. You also said that you wanted to read 60 seconds and all this logic is missing. A simple function of time elapsed, it's all you need.

• NEITHER USB-6008 can measure an AC voltage

  Now I am doing a project, but don't know if DAQ can measure an AC voltage or not, the acquisition of data that we use is USB-6008.

  Yes, it can measure AC in the range of +/-10 volts and have a sampling rate of 10kS/s.

  Application engineer OR

• Measurement of voltage USB 6008 ranging from 1mV

  Hi, I'm doing a supply at an angle for an amplifier using the USB-6008. The ranges I look are - 0.5 to 0.5 V and 0.5 to 2.5 V. To generate negative tensions, I use the + 2, 5V for a reading of differential voltage output as a 'ground '. Voltage measures have a delay that varies with the voltage, given this by drawing these variations and set the output to data acquisition there is still a 'noise' of +/-1 mv so that it is clear from this parcel of tension against the sample number:

  

  It seems that at some point the values are being rounded up to the nearest millivolt. I need to get to a resolution of 0.5 mV for my device, it will be possible with the USB-6008?

  The AO USB-600 x has a range from 0 to + 5 V and the 12-bit resolution. 5/4096 = 1.22 mV. Absolute precision is 7 mV typical and 36.4 mV maximum full scale.  The noise of the AO is not specified.

  If you measure the results with THE USB-6008, you have at least 0.5 mV, similar resolution system noise and absolute accuracy of 2.5 mV or more.

  It's probably as good as you will get with the box USB-6008.

  Lynn