Black screen after start - "Video_tdr_failure atikmpag.sys.

Similar Questions

• I have a black screen after start up, but the mouse behaves normally. What's wrong?

  Hi, today I turned on my Pavilion DV9500t off for an hour. It would normally start Windows 7 64-bit (the Welcome screen was during more than usual), but instead of going to my office, the screen went black with the cursor has normally and only flashes do not. No keyboard function works well.

  I started from the install disc and from there I fixed start-up (no problem found) and restored to the previous points several times without success.

  There is no error message and I have not noticed a strange behaviour, with a view to this. Any suggestions as to the cause and the cure are greatly appreciated.

  I suggest you reboot your device and pressing F10 to enter the BIOS. While in the BIOS, I ran the disk hard self test in the diagnostics tab and see what the results are.

• Mac mini black screen after upgrading to sierra

  Hello!

  My probleme:Mac Mini end 2014 black screen to start immediately after the upgrade of Sierra.

  Thanks for your help.

  Kentr0n

  Is there anything on the black screen (boot) at all ever?

• Pavilion 15 - p065tx: Pavilion 15 - p065tx, black screen after BIOS update recommended by HP assistant

  System reboot with black screen after accepting the update of the BIOS recommended by HP assistant this morning. AC power on at least three hours of waiting after the process completed successfully with auto update reboots always.

  Power light is on. Wired broadband light is turned on. Light CAP LOCK keyboard and led speaker hold noway.

  Hard reset has been tried 3 times with no improvement.

  External monitor is connected but no signal has been out of the laptop, screen is black.

  Done a few times this page to reset the BIOS setting blindly:

  http://support.HP.com/us-en/document/c02217843

  BEEPS heard when you press F10 or F5 during procedures. But still black screen.

  What can I try again?  Please advice kindly!

  Hi @ sokw,

  I have read and reviewed the post. Thanks for your reply. It seems that bios is damaged, and that is why the computer does not start. As it cannot be fixed by any software troubleshooting, you will need to contact the HP support by phone for the machine.

  HP technical support are available by clicking on the following link:
  
  http://h22207.www2.HP.com/us-en/?openCLC=true
  
  (1) once the page opens, please select the country in which you are located. Then enter your model of HP on the right number.
  
  (2) then choose "Contact the Support" tab at the top and scroll to the bottom of the page "HP Support - contact" to fill out the form with your details.
  
  (3) Once finished, click the "Show Options" at the bottom right.
  
  (4) Finally, scroll to the bottom of the page and select "Get a phone number." A file number and telephone number will now fill for you.

  I hope this helps. I would like to know how this happens. I really hope that the problem is solved without hassle and the unit works very well. Believe me, I've done everything I can to help by keeping your interests in mind. Please reach out for questions and I'll be there for you help.

  Just to say thank youPlease click the ' Thumbs Up 'button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• Re: Satellite L675-10 t black screen after disassembly problem

  Hi all

  I recently had some problems with my L675-10T overheating, even when I was with a big fan of cooling for the games.

  I realized that the problem resulted from blocked exhaust and dust and it is why, after reading and watching the many tutorials, I opened my laptop computer successfully and all cleaned up.

  The temperature dropped to 20 c and I was happy.

  The next night, however, took my laptop and headed for the living room, and it will stop.
  Black screen and nothing passed. So I ran to the internet and found this solution, it worked btw.

  1. turn off your computer
  2. unplug all wires (including energy)
  3. disconnect the battery from the bottom of the computer.
  4 re - connect the power cable. (the battery should not be in the computer)
  5. turn power on. The screen works. Choose start windows normally. (if you get this screen)

  The thing is, the same thing happened to me this morning as well.
  Twice in 2 days and im a little worried I did something wrong during Assembly of the laptop or something. Any ideas? Or do I keep accountant with the above solution?
  Looks like a mess of power upwards of sorts.

  Thank you in advance.

  Hello

  I assume that this question has not happened before you have disassembled the laptop. Right?
  To be honest this similar issue happened to me to. The portable light not (black screen) after I'm entered in the mode 'sleep'. However, this happened only once

  It s hard to tell why this happened to you it of not impossible that you have damaged something for disassembled the procedure.

  However, the fact is that the warranty is not valid more because you opened the laptop. That is why any approach (especially parts replacement) to solve this problem would cost money.
  So ultimately it s your decision: a technician visit to downtown to see the pieces of equipment or keep your stay with the workaround mentioned above.

• At the end of the factory restore, but black screen after "Windows has set up the computer.

  The model in question is VC863AA #UUW

  I want to get back the computer to the factory condition, so I rebooted and you press F11. Everything went exactly like this: http://support.hp.com/us-en/document/c00814731#N72 (chapter "Start a restore from the hard drive and the computer is off")...

  .. until step 10, which States:

  "The computer restarts and continues in the installation of Windows. Complete the configuration screens and wait until the computer finishes the installation program. "Then turn off the computer, reconnect all devices and turn on the computer.

  Yes, the computer restarts. She continues in the Windows installation (it says "medan windows konfigurerar datorn Vanta", which means roughly "Please wait while Windows configures the computer"). After that which was for about 5-10 minutes, the text disappears and the computer restarts by itself.

  After that, he gives a normal load Windows Vista bar and after that black screen. It seems to be a little bit alive but jammed somehow. If I let it be for several hours, he goes to the standby mode. If I wake up, he still won't. I can plug a USB another keyboard and he will make some access to hard drive (load a driver probably). I can press the sleep button and it will go into sleep mode. But if I press the power button / stop briefly, it will NOT stop.

  So finally, after several hours I forced to shut down (by pressing the power button / stop longer). When I start it, it goes back to behave as explained in the previous paragraph.

  If I press F8 during startup and select Safe mode, it goes in safe mode and I get dialogue indicating in Finnish:

  «Asenna Windows: Windows ei voi suorittaa vikasietotilassa asennusta.» See devam fenetresdans asennusta uudelleen tietokoneen kaynnistamalla. »

  Rough translation:

  "Installation of Windows: Windows cannot complete installation in safe mode." "You can continue the installation by restarting the computer.

  If I restart the computer, it goes back to the black screen after the windows loading bar.

  This suggests that there is something in the installation of Windows who jams it.

  I can install Windows Vista from a Vista DVD, but then I can't use the software included with the computer. (App States installation cannot install on a machine that is unauthorized, then of course they are looking for some OEM HP things.)

  Any suggestions on how to fix jam that continues with installing Recovery Windows or how to install the software on a normal Vista would be very appreciated.

  I solved the problem. Good thing I didn't order the restore disks, because that would not have solved the problem.

  I decided to post it because I don't know there will be others who have HP Pavilion Elite m9754sc and will have to face this problem of a black screen after the restoration.

  The fact is that the restore worked perfectly, but in this display card driver is buggy and it causes the screen to go black.

  I thought that what I installed fresh Vista which worked until I installed the driver from the recovery partition display. I tried VGA, outputs HDMI and DVI on the factory installed GeForce GT220 and none worked.

  A defective display driver should normally be no problem we could go in safe mode and fix it to the it. But as with the recovery goes to pre install state (ask what language to use etc.), safe mode does not work.

  So the solution is to unlock the display of the motherboard connectors and remove the factory installed GeForce GT220. Once the recovery and installation of Windows is finished using the graphics card integrated motherboards, you can reconnect the GeForce GT220 and get a updated driver with safe mode.

• Black screen after startup - Satellite A105-S4334

  It gives me black screen after the display of the logo just after the appearance of the cursor and nothing I can do except hold the button 'Disable' of windows, and then restart again, it shows the menu to make it start in safe mode... network mode... normally or lastest know good windows start...

  When he starts for the second time it works very well, he does it all the time and now I'm reinstalling windows for the 2nd time (factory State) any solution or explanation for that matter?

  Hello

  It is not easy to say why this is happening. Have you standing connected an external device, such as USB, printer or something similar?

• Qosmio X 870-149 - black screen after update to 8.1 win

  After an update to win 8.1, I got a black screen after connection, the only thing I could do was to press zero when starting and make a recovery facility.

  It took 40 hours, I don't know why it took so long, but when it was over, the HARD drive was completely empty, so I installed win 7 instead, because I had not done? a restore CD. The problem now is that I still get black screen between the two, and think it might be a heat problem, I still have the warranty, but I don't know if it applies when I installed win 7 on the machine.

  I still have a warranty on my Qosmio toshiba

  Hello

  Well, the guarantee covers material related problems. It does not any problem with the software.

  Now the question is: why the black screen appears?
  Is - this problem is hardware or software?

  What happens if you access the BIOS?
  You don't see anything on the screen?

  Something is visible on the external monitor?

• HP G60 laptop: black screen after sleep or hibernate Windows10

  Since upgrading from Windows 7 to Windows 10, the laptop displays a black screen after the sleep or hibernate modes.  The system seems to be commissioning (HDD, fan action), but no video.  The system boots normally cold trouble-free starting.  Never, there is this problem with Windows 7.

  Hi @Bobby876,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP G60 laptop and problems with the mode "sleep" after the update to Windows 10. I recommend to restore the default BIOS settings. You could restore the BIOS with this document by selecting the reload the default BIOS settings. In this way, it will look at the hardware installed on your laptop.

  You can try:

  In Device Manager, click the arrow

  next to display adapters to expand this category
  Right-click on the graph, and then select Update driver software if more than 1 graphic adapter do 1 at a time.
  Select search automatically for updated driver software.

  The laptop must find and automatically install the updated driver
  Once the installation is complete, restart your laptop.

  You can try to use the Windows Update Troubleshooter to fix updates that do not come through Windows 10.  Please restart the laptop twice to make sure that all updates are completed!

  Please let me know how it goes.

  Thank you.

• Corrupt BIOS V5 531 Acer black screen after startup, f2 and f12 also. Repairable?

  Hello

  Yesterday I tried to install Win 7 if I could play D & D Neverwinter on Arc after using * nix systems study (looking to start a career as an administrator). I had plugged into a power strip that was, unbeknownst to me, turned off and I went to make coffee and watch some news. When I came back to check the progress of my laptop was powered off and since then I havn't been avle start without being blocked at a black screen after the start page of the bios. The f2 and f12 also leads to a black screen, I can not change the boot device or enter the bios Setup.

  Is - fixable at all? For example, is the a key-combo, I can use it to restore from a backup bios? Or, do I have to bring in a technician who can install a new chip bios or flash this old some how? Or did I brick pemanently my device?

  V1.22 is what you want to be part of a unit of Windows 7.

  The problem is if it crashed during the upgrade process, it will take some special tools clearly on the chip on the MB and recharge it with a new BIOS. I would contact your local support team to see what options are available.

• Pavilion 15-243cl after automatic update of windows 8.1 I get a black screen after the home page.

  recently installed an automatic update of windows 8.1. Now, I get a black screen after the home page. I can load the Task Manager and access the internet. tried to go to the SafeMode to start with f8, but several attempts failed. I updated my graphics driver from AMD today and same black screen. I've also restored sytem to an earlier date using the HP utility with results screen - black even after the home page.

  Hello

  Try the following.

  Boot the computer normally and log.

  Black screen, old the ctrl and alt keys and press delete.

  Select Task Manager.

  Click on file and select the new task.

  Type rstrui - also enter a tick in the box for "create this task with administrative privileges" - and click on Ok.

  When the system restore interface is loaded, choose a restore point at least 48 hours before the opening of session question (IE before the last batch of Windows updates have been applied) occurred initially and then proceed to the system restore.

  Kind regards

  DP - K

• Black screen after the windows login

  Hi, I have a HP Pavilion DV7 notebook with Windows 7 Home Premium installed on it. A problem I've noticed is that, once I connect to windows during a boot, the screen is black for about 1-2 minutes. After awhile, explorer.exe would with desktop, taskbar and icons. I am concerned about this 1 to 2 minutes of black screen after the boot as it did not exist previously. I know I have options such as restoring the computer laptop back to the default state, or by using the system restore. However, I don't want to lose all my stuff, and with respect to the restoration of the system, I'm not sure when the problem happening, as it was some time ago. I have read a Microsoft article, (http://windows.microsoft.com/en-US/windows7/why-is-my-screen-black-when-i-start-windows-7) and tried all the steps with the graphics card and the regestry, but nothing seems to work.

  -Task Manager is able to open when the screen is black (shows explorer.exe running)

  -J' have the drivers on the HP support site

  -laptop is HP Pavilion DV7 3024ca

  You will need to login using the method of trial and error. Please uncheck all of the MSCONFIG Startup tab and restart the system. If the black screen issue is resolved, then check out an application every time and restart the system. This will help you to identify the program interfere.

• T60p Black Screen after startup

  Hi gurus,

  My blackened screen after starting today. I see barely any records and office of shadows. Looks like my LCD or backlight is aging or dying, since I've been see some pink screen occasionally for the last couple weeks.

  Strange thing is, the screen is black with a power cord plugged and without power cord if I turn the clear screen to the maximum level (level 7), but if I keep it under level 5, the blacklight is on and it is always achievable (not good for me though).

  So with that, I have to go to a repair store and replace my LCD set? or just the retro-lighting/inverter? or maybe just the conneting cable? How these possibilities would respectively cost me?

  Type: T60P 2007

  Operating system: XP

  Warranty has expired earlier this year.

  Really appreaciate your entry!

  Evan

  about 700 dollars if you take the laptop to a repair center. If you don't know how to do it you should ask our people to the forum.thinkpads.com, they are few who can do it and much cheaper.

  Get a quote on their part first and see what happens, if you decide to not go through a repair, you can sell the market on forum.thinkpads.com for at least 300-400 USD depending on the conditions and specifications.

• Black screen after the attempt to upgrade to windows 10

  I was trying to upgrade windows 7 on a laptop HP Windows 10. The first attempt was via the white windows logo in the taskbar. This attempt was interrupted, probably accidentally turned off the button wifi trying to move the computer. The second time I tried to use windows ten upgraded Installer. I did the usual download and installed up to 99%. He remained on the installation of 99% during the night and the next morning without change. I turned off the computer and he made a series of updates before shutting down for good. When it starts again, it has a black screen but the cursor is there and movable. I tried in safe mode for the repair and restoration of the system, but it did not work. I tried to reset the BIOS to default, but does not. I try to leave the computer turned off for an extended period of time disconnected from the internet to see if that helps. The last attempt to start, windows 7 seems to start but then ends up on the black screen and I held down the power button to stop it. I'd rather upgrade to windows 10 if possible, but if cannot then if can go back to windows 7 will be enough. It worked great on Windows 7 before trying to upgrade, so there is no problems with the computer.

  Hi Chris,

  I'll be happy to help you with the problem you have with black screen.

  The problem may occur if the video drivers are not updated.

  What is the model of your HP computer?

  I suggest you follow the suggestions by Sharath Srinivasan replied on August 7, 2015, the link below:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-hardware/black-screen-after-upgrading-to-Windows-10/cf3b4559-67d8-40E0-9cf2-ebf4528e1e78

  Please reply with the results, we are happy to help you.

  Thank you.

• Black screen after the failure of the connection - win 10 win7 installation

  Hello

  SYSTEM ERROR
  Cause
  I tried to install win10 on a PC running win7. Installation stalled at 99% and I restarted.
  The problem
  Now he still run win7, but once connected, the screen is completely black except for cursor. Features such as the job-work list as it should and in safe mode, the screen is not black after login.

  PC INFORMATION
  The video card
  My video card is "Mobile Intel (R) 4 Series Express Chipset Family" (driver version: 8.15.10.2202) Driver date: 25/08/2010) and windows tells me that the video card (graphics - in my language) is updated to the latest version.
  The model
  ASUS Pro79I Series. With Windows 7 64 bit

  Mathias, cordially

  Denmark

  Hi Mathias,.

  According to the description of the issue you do not get black screen after login in safe mode. For example, there might be a chance that the display driver is either corrupted or need a update. Please, try the steps to uninstall graphics card in Device Manager, uninstall the drivers of device from the list of programs, and then download the latest drivers from the manufacturer's website.

  Step 1:

  Uninstall the device from Device Manager

  • Open the Device Manager
  • Expand the section of the graphics card .
  • Find the Display card Driver.
  • Graphics Driver right click and choose Uninstall.
  • Select the check box delete the driver for this device.
  • Restart the computer after the uninstall is complete.

  Step 2:

  Uninstall the drivers of device from the list of programs in the control panel

  • Click Start, select Control Panel
  • Now, click on programs and select programs and features.
  • Find the Display card Driver.
  • Display driver card click right and select Uninstall.
  • Restart the computer after the uninstall is complete.

  Step 3:

  Download and install the latest drivers for the graphics card from the Web site of the manufacturer (ASUS)

  Hope it would help. If the problem persists post returns with the required information, the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards