cannot install downloads/impossible restore/recovery

Similar Questions

• Cannot install Office97pro after system recovery using windows XP. System does not seem to recognize the drive.

  After system recovery cannot reinstall dvd office97pro. It seems that windows XP does not recognize the program on the disk.  Tested the dvd on my computer laptop windows 7, charges fine. Help!

  Hi Fred Chandler,.

  1. What happens when you insert the DVD in the drive?
  2. You receive an error message?
  3. You are able to use the other DVDs on the computer?
  4. Do you have any third-party DVD burning software installed on the computer?

  If you are facing a similar problem with all DVDs on the computer, refer to the article below and then try the steps mentioned, check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

  If you face this problem with the Office 97 DVD then I would suggest that you post your request in the forums of Microsoft Office.

  http://answers.Microsoft.com/en-us/Office/Forum

• Portege M400 - cannot install OS or restore an old image

  I have a portege M400 and im hardly set any operating system of windows on them. When it gets to the stage where he asks what hard drive to put in place the windows files to, it does not detect the drives.

  I also have an image on a hard drive that I use a universal driver restore program to restore to any laptop regardless of the make and model and which also blue screens after the logo of windows xp when it starts up. The toshiba is the first laptop that I fell on this issue.

  The BIOS is currently 1.8 I think, I can't even put the hard drive in compatibility mode or AHCI.

  im a little confused about restrictions of this laptop.

  Can someone guide me on what I need to do to install windows on this machine please?

  Timox is right: the RAID driver must be added during the installation of Windows XP.
  During installation, you will be asked to add 3rd third-party drivers. As I m not wrong not you must press F6 to add the RAID driver.

  Very important note: do not format the HARD drive once the RAID driver has been added because this would remove the RAID driver from the HARD drive and installing Windows XP will fail again.

• cannot start windows or restore/recovery

  When I start it, it gives the opportunity to "Startup Repair" or start windows normally.  When I choose "start windows normally", he gets in what concerns microsoft logo, then restarts.  When I choose "startup repair" he said first me "Startup Repair couldn't fix the problem" and I get two options listed. "Microsoft System Restore" and "sytem recovery" (which is opaque and not selectable) when I choose "System Restore" I am able to do as much as you select a restore point, and then it lists the "c:" drive and gives the warning yellow and says sign 'can only restore from a drive that contains Windows', I select 'c:', but the 'next' button is not selectable.  So, I have to go 'back' or 'Cancel', I was able to enter a command promt and look at the directory of the c: drive and only the 'SYSTEM' the d: cottage has all the files because it is a backup.

  Is it possible to boot windows ff drive d: via the command prompt?

  Hello
  1. have you made changes on the computer recently?

  Method 1.
  We can try the last good known Configuration option and check if it helps to resolve the issue.
  Using the last good known Configuration
  http://Windows.Microsoft.com/en-us/Windows7/using-last-known-good-configuration

  Method 2.
  Start your computer in safe mode and then configure your computer for the clean boot and check if it starts successfully. If it starts successfully can be a third-party application or service is causing the problem.
  Troubleshooting in safe mode
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshooting-problems-while-in-safe-mode
   
  We can use the approach 50 / 50 to narrow down the root cause of the problem.
  See the article below for instructions on how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Cannot install download files on the generator on new glassfish

  Hello
  Running Application Express 4.1.0.00.32 on Oracle Glassfish Server 3.2.1. Our new facility is in place and do us our applications up and running for the most but with a weird thing. We cannot transfer all files on the generator of the Apex, for example an image or an export request export. After navigating to the file by clicking 'next' in the Import Wizard generates a message "the file must be selected for upload" and the path specified just disappears from the display.
  
  Sorry to post on the forum of listner, but it "feels" as a kind of a problem of front end with the new facility. Others post similar topics on the forum of the apex and say: there is a bug in glassfish How to transfer files to the apex
  
  This post refers to the other off the coast of the Forum post where you can download a patch of glassfish. But hey, I'm paying for an official Oracle glassfish, I must post an sr for this?
  
  
  
  Thank you
  Steve

  Hi Steve,.

  We have discussed this here even before the thread you referenced: {message identifier: = 10205967}
  Of course, this fix is intended to be used for GF OSE, not the version with support.

  But hey, I'm paying for an official Oracle glassfish, I must post an sr for this?

  That's how you get help for this. Maybe "My Oracle Support" (formerly known as Metalink) has already a bug filed for this and an official patch to download. This forum is not intended to replace or duplicate content published by the official product support.
  On the other hand, your version number seems inaccurate: the most recent Oracle GlassFish Server available today is 3.1.2.2. If you are running on 3.1.2 you must download the Patch 147904-06 (assuming that you are on Linux, get the patch for your operating system if it is different). This will update your GF in 3.1.2.2, which is what Oracle Support will usually ask you to do if you open a service request for a product running on an older patch level.

  -Udo

• Cannot install download for a free trial assistant

  I need to install a trial version of Adobe Acrobat Standard XI. It downloads the companion, but the wizard will not run or install.  I use a Wiindows Vista operating system.

  JHarris955 you can also try the process listed on http://prodesigntools.com/adobe-acrobat-xi-pro-standard-reader-direct-download-links.html to download the software.  Please ensure that you meet the very important Instructions before you scroll to the bottom of the page and click on the download links.

• Bootcamp error: "the startup disk cannot be partitioned or restored to a single partition" and Windows recovery partitions

  I have Setup with Bootcamp Windows 8 and then upgrade to Windows 8.1, and then upgrade to Windows 10.

  When I want to restart the training camp that I got the error message: "the startup disk cannot be partitioned or restored to a single partition.

  According to this page, it is because of Windows recovery partitions added during the 8 to 8.1 migration and 8.1 to 10.

  I check with diskutil and I found 2 partitions of Windows Recovery:

  diskutil list

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 500,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage Macintosh HD 419,4 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 79.1 GB disk0s4

  5: Windows Recovery 471.9 MB disk0s5

  6: Windows Recovery 472,9 MB disk0s6

  / dev/disk1 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD GB + 419,0 disk1

  Logical volume on disk0s2

  C961E459-1E0D-4060-A467-3B4A705264AA

  Unencrypted

  I tried to delete the Windows Recovery 2 partitions with disk utility tools but the button "-" to remove them were leaving is disabled.

  Is it a good idea to remove these partitions? If yes how?

  1. What is the year/model of your Mac?

  2. you are trying to install a new copy of the W10 or remove the existing installation?

  3. do you have the W8 or installation/upgrade W8.1 had problems before the upgrade of the W10?

• Cannot install Windows 7 on Envy 14-1211nr of HP recovery disc sent twice

  Cannot install Windows 7 on Envy 14-1211nr of HP recovery disc sent twice

  The Recovery Manager starts well. He correctly completed the following steps:
  1 format HDD

  2. copy the files from the CD to the drive. It copies all the 3 CD.

  Then he ask the driver (the 4th CD) CD. Once I have this CD, then after awhile I get messge below:

  Contact HP support

  In most cases, recover the hard disk will solve your problems.

  If your problem persists, you may have to contact HP support. Find details of support HO in the documentation of your PC.

  After that I see above meaage the only button I can click is "Finish". Once I click on finish, then in a minute, I get a message that "recovery completed successfully.

  The laptop restarts and displays the message on the screen "Bootmger" not found

  I called HP support and asked to run the hard drive and memory test and he succeeded.

  I can install windows on another CD I have with.

  But I can't install WIndows using the recovery CD, I received from HP. It's the 2nd CD series that I received these don't work or the other.

  I have two identical laptops. Tried installing on both and having the same problem on both.

  Can you please help with this.
  HP sends fake CDs?

  Kind regards

  Hello

  Here is another solution, you can try to see if you can get Windows 7 to install correctly.

  Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

  An example of a COA label can be seen here.

  You can create an installation disk yourself using another PC - just download the good Disk Image ( this must be the version exact same origin supplied with your laptop ) from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is here.  These Images are clean and a well respected source, however there are only limited versions available.

  Windows 7 sp1-iso-official-32-bit-and-64-bit

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  All pilots additional and the software, you may need can be found here.

  Kind regards

  DP - K

• Windows XP32bit SP2 cannot install SP3 beyond the point of restoration

  WindowsXP32 SP2 cannot install SP3 update spent to install point of restoration, never had a problem before.

  WindowsXP32 SP2 cannot install SP3 update spent to install point of restoration, never had a problem before.

  Not much to go...

  Is it a new installation?  Connected to the Internet with Windows Firewall on?  What anti-virus software is installed?  All hardware device drivers (and THE system BIOS) is up to date?

  Search for malware:

  Download, install, execute, update and perform analyses complete system with the two following applications:

  • MalwareBytes (FREE)
  • SuperAntiSpyware (FREE)

  Remove anything they find. Reboot when necessary. (You can uninstall one or both when finished.)

  Search online with eSet Online Scanner.

  Cleaning the components of update on your Windows XP computer

  While probably not 100% necessary-, it is probably a good idea at this time to ensure that you continue to get the updates you need. This will help you ensure that your system update is ready to do it for you.

  Download and run the MSRT tool manually:
  http://www.Microsoft.com/security/malwareremove/default.mspx
  (Ignore the details and download the tool to download and save to your desktop, run it.)

  Reset.

  Download/install the latest program Windows installation (for your operating system):
  (Windows XP 32-bit: WindowsXP-KB942288-v3 - x 86 .exe )
  (Download and save it to your desktop, run it.)

  Reset.

  and...

  Download the latest version of Windows Update (x 86) agent here:
  http://go.Microsoft.com/fwlink/?LinkId=91237
  ... and save it to the root of your C:\ drive. After you register on theroot of the C:\ drive, follow these steps:

  Close all Internet Explorer Windows and other applications.

  AutoScan--> RUN and type:
  %SystemDrive%\windowsupdateagent30-x86.exe /WUFORCE
  --> Click OK.

  (If asked, select 'Run'). --> Click on NEXT--> select 'I agree' and click NEXT--> where he completed the installation, click "Finish"...

  Reset.

  Now reset your Windows with this FixIt components update (you'll use the aggressive version - if requested):
  How to reset the Windows Update components?

  Reset.

  Download Windows XP SP3 full installation program )<-- that="" is="" a="" link),="" save="" it="" to="" your="" desktop,="" reboot="" and="" logon="" as="" an="" administrative="" level="" user="" and="" only="" double-click="" on="" it="" to="">

  Come back - we know the results...

• Can't install downloaded software, receive the message error "Windows cannot access the specified device, file, or the path"

  Cannot install any software downloaded - says "Windows cannot access the specified device, path or file.  You can not have the appropriate permissions to access the item.  This happened after I went on a bad site and downloaded something accidentally and I was not able to do anything after that.  I have avast and avast kept popping up saying I've made to a site with malware and that it would interrupt - well these pop - ups have ceased and I was scanning my computer using windows defender (which did not find anything) - but I still have problems on my computer. Should what steps I take?

  Hello

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  also run the sfc/scannow command.

  http://support.Microsoft.com/kb/929833

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally madeprograms,Accessories, right-clickguest, and then clickrun as administrator. If you are prompted for an administrator password or a confirmation, type the password, or clickallow.
  2. Type the following command and press ENTER:
     sfc/scannow

     The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions

  If SFC detects the main problems it can't fix you may need to borrow a Microsoft dvd vista not an acer, HP etc. recovery disk and do a repair installation

  read the below tutorial on how to perform a repair installation

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

• Satellite 2450-S203 - installed XP SP1 of recovery CD - cannot update

  The hard drive on my Satellite 2450 S203 has not then I replaced and installed XP from the recovery CD. Everything's fine. I now have a PC running XP SP1.

  I tried the update of XP start > all progtrams > Windows update but it failed, the updated software I used was not compatible with the update site or something similar.

  I found a site of Microsoft, who said I had to install SP1a and then put to SP1a update to SP3. I downloaded the SP1a installation tool and it seemed to do things, and I'm guessing that SP1a installed OK.

  When I go to start > all programs > Windows update, the update starts OK but after a few moments, I get an error message on the Microsoft Update Server does not.

  * Question 1: *-anyone have any ideas what I should try next?

  * Question 2: * fact Toshiba have nowhere where I can download a more current version of XP - SP2 or SP3 say - so that I can eventuially happen to SP3 without SP1?

  Any thoughts are welcome!

  > Question 1: someone has any good ideas what I should try next?

  Win XP SP1 is part of SP2. So, you can download the SP2 package from Microsoft or any other Windows pages page just google
  So after installing SP2, you can follow with SP3.

  Before you install SP3, you will need to install SP2 first

  > Question 2: Toshiba has nowhere where I can download a more current version of XP - SP2 or SP3 say - so that I can eventuially happen to SP3 without SP1?

  On the pages of Toshiba, you can download only the drivers and Toshiba tools
  Windows Service Packs are Microsoft products, and you should check the Microsoft pages for this.

• Cannot install Realpalyer downloader

  Help me to install Realplayer Downloader in my computer. I installed this before but it cannot install now after my computer crashed partially after a virus. It seems to be a mismatch. What will I do?

  Hello

  • What happens when you try to install it?
  • You receive an error message?

  You can follow the steps that can help you solve your problem below:

  Step 1: Perform a clean uninstall of disturb RealPlayer.

  Follow these instructions

  Important: Before you reinstall RealPlayer disturb, do step 2 below.

  Step 2: Remove the Windows files and temporary folders.

  1. in the lower left corner of your screen, click Start.

  2. go in programs (or all programs in Vista).
  3. go to Accessories.
  4. go to System Tools.
  5. click on Disk Cleanup.
  6. Select drive c :) , and then click OK.
  7. ensure that the temporary Internet files is selected and click OK again to delete the selected locations.

  Step 3:

  I recommend to configure your computer to boot and then try to install Real player disturb.
  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Note: Ensure that you download the package to correct RealPlayer for your version of Windows.

  Still having trouble?
  If these steps do not resolve the problem, please contact a RealPlayer Customer Support.

• Cannot install Lenovo Onekey Recovery

  I just downloaded the Onekey Recovery for 530 Y, but I can't seem to install it. I accidentally uninstalled the previous, and now I can't get it back. When I tried to install it, I get an error sayinig "this software can only be installed on a Lenovo system", but I use a Lenovo system.

  Extract the files from the EXE with Universal Extractor. Go to the directory where the files were extracted and delete a file called "Custom". You should be able to install it then.

• Cannot install new Norton 360 download

  I bought a Norton 360 3PC.  I uninstalled the Norton 360 has expired and cannot install a new one.  I must not have read the instructions properly because it uninstalled my current Norton but stopped the process.  Now, my DVD player does not work (I tried other CS to check).  The CD says you can load from the internet, but I can't find the download of Norton 360.  I have the product key.

  https://www-secure.Symantec.com/Norton-support/JSP/product.jsp?version=current&product=Norton+360&LG=English&CT=United+States&INID=hho_support_buynorton_en_us&PVID=f-N360-cur

  Personally, I would like to request a refund and then get a better product.
  Microsoft Security Essentials (free)
  eSet NOD 32 Antivirus 5 (IMO, you don't need the extra stuff to a security suite, eSet or Norton).

• Cannot install Microsoft Expression Studio 4 with downloaded SP3. Do you know why?

  Cannot install Microsoft expression Studio 4 with downloaded SP3.

  Try posting your question on the forum of Expressions: http://social.expression.microsoft.com/forums/en-US/web/threads/

  J W Stuart: http://www.pagestart.com