Cannot restart after SP1 cross post w / repair forum

Similar Questions

• Cannot restart after failure of the accident or the power

  I have two Sandisk Ultra II 240 GB SSD and this has happened at a time using Windows 7 and Windows 10. Basically if my laptop is not closed properly - off without shutdown or restart, the laptop completely failed to restart Windows. This has happened on Win 7 and 10, but at least 10 gave me an error message with an error Code 0 x 0000185 and something abut my MSConfig being unreadable file or something. Whenever I have to wipe the hard drive and reinstall Windows and watever I do, this happens again and again and cannot restart the computer. Is this a bug? I tried this with a total of three different Sandisk Ultra II SSD and it happens over and over again. Help?

  Hello

  This could be related to any other equipment that you use on the specific computer, so my suggestion would be to try one of the disks on another computer to see if the problem is in the car.

• Cannot restart after a repair disk Warrior

  I have an iMac 27 "(2010, je pense) running 10.11.2 and a terabyte of hard drive, which is more than half full."  He has been doing progressively slower for some time, so I bought Disk Warrior to rebuild the directory and, hopefully, speed things up.  The whole reconstruction process takes about 24 hours, which seemed a lot of time for me, but, finally, he informed me that everything had been repaired.  However, now when I try to reboot, I get the chime and then the logo apple with progress bar, but who just stops after 5 seconds.  I tried to reset the PMU and NVRAM but no joy. I also tried the disk utility apple recovery mode running to see if there was a problem with the permissions, but no joy there.  Would there be any point in rerunning Disk Warrior?  I had rather not go through another 24 hours without the computer, if there is a faster solution.  Any ideas anyone?

  Try a boot sure try safe mode if your Mac does not end commissioning - Apple Support

  FWIW Disk Warrior is not intended to be used for the purposes of general maintenance. It is mainly to fix problems that disk utility can not and for the recovery of lost files. If your Mac is slow, it is probably caused by material insufficient, intrusive or incompatible software or a problem hardware no software will correct. When you get your Mac running again to run and view a report of EtreCheck and we can give you some suggestions for return to normal http://etrecheck.com/

• Cannot restart after El Capitan put 10.11.6 updated

  I have a MacBook Pro (13-inch, mid 2012) with the OS X10.11.5 (15F34). When the update to 10.11.6, rebooting is not the case, the update is not implemented. Finder and System Information.app do not react. It is impossible to relaunch the Finder or kill the Information.app system. I tried a hard stop, but I come back to the same situation, even after waiting the necessary time to reopen not already running applications. How to do this?

  The only application that I recently installed is Express Scribe, a transcription software I really need and I am reluctant to remove or uninstall. Is there a solution? Thanks in advance for your help.

  Try to boot inSafe Mode and see if the problem persists? This will allow to test if the problem is in your user or system.

  Restart now ' shift '.

  (Wait to take more time to start in this way because it runs a check of directory first. Also give it some time after the start because he runs maintenance routines at the beginning).

  If this does not work, see this topic Support of Apple:

  If your Mac will not turn on - Apple Support

• Cannot restart after optional updates from Microsoft. Down arrows don't work when in the loop boot selection page

  Went to Microsoft Update and downloaded and installed a few optional upgrades, including one about a driver. After installation, will not restart. Arrive at the page Windows XP will then black screen and then the boot selection list. Is "glued" to the normal startup and arrows don't work for go mode without failure or any other option. He just times down, try to reboot and loop. Help!

  Hello

  Have updates you installed?

  You can check the KB number for the update in the update history:

  1. Click Start, click all programs, and then click Windows Update or Microsoft Update.
  2. on the Windows Update Web site or the Microsoft Update Web site, click on view update history.

  Step 1: Unplug the power cable, the keyboard and mouse and then reconnect it back. Now, check if you're able to boot in safe mode (by using the arrow keys) or normal mode. Send back the same.

  Step 2: Alternatively, you can restore the system from the recovery console.

  Reference:
  How do I recover from a corrupted registry that prevents Windows XP startup
  http://support.Microsoft.com/kb/307545

• Cannot restart after the update of XP last night (08/13/09)

  Power the computer off last night, he said "stop after installing updates", so I just left the office.
  Is here this morning, the computer will not re-start in safe mode or safe mode with command prompt.
  I get the "Sorry for the inconvenience" screen
  A ran a chkdsk and rebuild bootcfg
  When I try to start in safe mode, it seems to load takes with several lines of things like:
  "multi (0) disk (0) rdisk (0) partition (1) \WINDOWS\system32\ntoskrnl.exe ' etc, etc.
  then hangs just at a black screen with the last few lines of that on it.
  I can get start menu with f8, I can run the retore console, but I can't get a safe mode prompt to try a system restore from there.
  HELP, I'm stuck.

  And Yes, I know it's a Questionmark XP a Vista forum, but I can't find the XP forum.

  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?DG=Microsoft.public.windowsupdate&cat=en_us_d99bb655-a5d5-4C07-bdb0-90caf9f30c42&lang=en&CR=us

  Microsoft.public.windowsupdate discussions

  Link above is for the focus group you need.

  XP discussion groups:

  http://www.Microsoft.com/windowsxp/expertzone/newsgroups/reader.mspx?DG=Microsoft.public.WindowsXP.General

  Link above is to the XP newsgroups.

  There is a list of groups of discussion XP to the bottom of the left column.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• Cannot restart after the update

  Hi givepaulhelp,

  Since you was not able to continue the analysis as possible you have spyware or virus.  Here are a few options for scanning your system.  No one program can catch them all.

  Virus scan help

  http://windowshelp.Microsoft.com/Windows/en-us/help/5c08774a-6602-490d-ba33-faed5c8939911033.mspx

  Spyware scan help

  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/fa30853d-719a-4265-9e7b-9287567d31e3

  Thank you for using answers Forum. Please let us know how it works.

  Joseph
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  Two more days but I'm getting nowhere other than having may be a better solution on what is false. It seems that, although the Windows Genuine Advantage Validation auditor finds that my copy of Vista Ultimate is valid, it always returns a 0x80070426 error (also an error 0 x 80070002). I can't turn on the software licensing service and various functions do not work (for example control panel, windows update, audio). The report below (now that I finally understood how to generate it) will probably be helpful to someone who knows more about this stuff than me.

  I tried spyware and malware scans of four different programs all came the harmless (other than tracking cookies) empty, so I think that the problem is related to my registry get corrupted when I tried to install an update to Windows (or IE8). My problem looks roughly the same as that for the guy in this link: http://social.microsoft.com/Forums/en-US/genuinevista/thread/5c956fd9-0ade-4841-8383-c53e93d47680 but before I try something stupid, please give me a start. (As I have tried scannow and I can't boot mode safe (only ' disable the drive Signature Enforcement'), the solutions in this link don't work anyway) I think that it all boils down to getting the software licensing service to work and maybe a few other corrupt fixing registry entries. Could a SP2 install on do I cure everything?

  Diagnostic report (1.9.0006.1):
  -----------------------------------------
  Given WGA-->
  Validation status: genuine
  Validation code: 0
  Validation code online: 0x80070426
  Cached Validation code: n/a, hr = 0x80070426
  Windows product key: *-* - VFWRT - JGH7R-R933G
  The Windows Product Key hash: gYrJFhcKVmHMbiVVuoEU7w/jsC0 =
  Windows product ID: 89580-OEM-7332132-00015
  Windows product ID type: 2
  Windows license Type: OEM SLP
  The Windows OS version: 6.0.6001.2.00010100.1.0.001
  ID: {8AD0B022-238E-42BD-A5CF-1328933C5B04} (3)
  Admin: Yes
  TestCab: 0x0
  WGA version: registered, 1.7.59.1
  Signed by: Microsoft
  Product name: Windows Vista (TM) Ultimate
  Architecture: 0x00000000
  Build lab: 6001.vistasp1_gdr.090302 - 1506
  TTS error:
  Validation of diagnosis:
  Resolution state: n/a

  WgaER data-->
  ThreatID (s): n/a, hr = 0 x 80070002
  Version: 6.0.6001.18152

  WGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  File: No.
  Version: N/a, hr = 0 x 80070002
  WgaTray.exe signed by: n/a, hr = 0 x 80070002
  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002
  WGATray.exe signed by: n/a, hr = 0 x 80070002
  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->
  Office status: 100 authentic
  Microsoft Office Standard Edition 2003 - 100 authentic
  OGA Version: N/a, 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->
  Proxy settings: N/A
  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
  Default browser: C:\Program may Explorer\iexplore.exe
  Download signed ActiveX controls: fast
  Download unsigned ActiveX controls: disabled
  Run ActiveX controls and plug-ins: allowed
  Initialize and script ActiveX controls not marked as safe: disabled
  Allow the Internet Explorer Webbrowser control scripts: disabled
  Active scripting: allowed
  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->
  [File mismatch: C:\Windows\system32\Slsvc.exe[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\drivers\Spsys.sys[6.0.6001.16606]
  [File mismatch: C:\Windows\system32\Slcext.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\advapi32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\rpcrt4.dll[6.0.6001.18051]
  [File mismatch: C:\Windows\system32\authz.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\msvcrt.dll[7.0.6001.18000]
  [File mismatch: C:\Windows\system32\samlib.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\ntdsapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\dnsapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\ws2_32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\nsi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\user32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\gdi32.dll[6.0.6001.18159]
  [File mismatch: C:\Windows\system32\msimg32.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\powrprof.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\setupapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\oleaut32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\ole32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\shell32.dll[6.0.6001.18167]
  [File mismatch: C:\Windows\system32\shlwapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\version.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\winmm.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\oleacc.dll[4.2.5406.0]
  [File mismatch: C:\Windows\system32\mmdevapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\wtsapi32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\regapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\crypt32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\msasn1.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\userenv.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\netapi32.dll[6.0.6001.18157]
  [File mismatch: C:\Windows\system32\psapi.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\netrap.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\wldap32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\winbrand.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\iphlpapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\dhcpcsvc.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\winnsi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\dhcpcsvc6.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\gpapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\slc.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\gpsvc.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\sysntfy.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\winsta.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\nlaapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\ncrypt.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\bcrypt.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\mpr.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\credui.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\cryptui.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\wintrust.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\imagehlp.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\dbghelp.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\mssign32.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\normaliz.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\tapi32.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\rtutils.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\rasapi32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\rasman.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\rasdlg.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\mprapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\activeds.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\adsldpc.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\atl.dll[3.5.2284.0]
  [File mismatch: C:\Windows\system32\certcli.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\winscard.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\netplwiz.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\propsys.dll[7.0.6001.16503]
  [File mismatch: C:\Windows\system32\xmllite.dll[1.2.1009.0]
  [File mismatch: C:\Windows\system32\mlang.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\apphelp.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\msiltcfg.dll[4.0.6000.16386]
  [File mismatch: C:\Windows\system32\shunimpl.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\devmgr.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\newdev.dll[6.0.5054.0]
  [File mismatch: C:\Windows\system32\dwmapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\winspool.drv[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\cscapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\uxtheme.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\windowscodecs.dll[6.0.6001.18131]
  [File mismatch: C:\Windows\system32\ntshrui.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\feclient.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\shdocvw.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\browseui.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\imm32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\msctf.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\duser.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\winsxs\x86_microsoft.windows.gdiplus_6595b64144ccf1df_1.0.6000.16386_none_9ea0ac9ec96e7127\gdiplus.dll[5.2.6000.16386]
  [File mismatch: C:\Windows\system32\msi.dll[4.0.6001.18000]
  [File mismatch: C:\Windows\winsxs\x86_microsoft.windows.common-controls_6595b64144ccf1df_5.82.6000.16386_none_87e0cb09378714f1\comctl32.dll[5.82.6000.16386]
  [File mismatch: C:\Windows\system32\comdlg32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\printui.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\cfgmgr32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\puiapi.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\hlink.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\usp10.dll[1.626.6001.18000]
  [File mismatch: C:\Windows\system32\inetcomm.dll[6.0.6001.18049]
  [File mismatch: C:\Windows\system32\msoert2.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\efsadu.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\mfc42u.dll[6.6.8063.0]
  [File mismatch: C:\Windows\system32\odbc32.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\oledlg.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\linkinfo.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\query.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\clbcatq.dll[2001.12.6931.18000]
  [File mismatch: C:\Windows\system32\cabinet.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\scecli.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\w32topl.dll[6.0.6000.16386]
  [File mismatch: C:\Windows\system32\rpchttp.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\fwpuclnt.dll[6.0.6001.18000]
  [File mismatch: C:\Windows\system32\ktmw32.dll[6.0.6001.18000]

  Other data-->
  Office details: {8AD0B022-238E-42BD-A5CF-1328933C5B04}1.9.0006.16.0.6001.2.00010100.1.0.001x 32*-*-*-*-R933G89580-OEM-7332132-000152S-1-5-21-380590955-2360834419-2564638157HP-Pavilion,RP827AV-ABA m7790yPhoenix Technologies, LTD. 5.0820070330000000.000000 + 00051333507018400FA04090409Central Standard Time(GMT-06:00)03HPQOEMSLIC-CPC100100Microsoft Office Standard Edition 2003114A0FF75D558A06A6zOCHSyGe8q22gukGZX7yf5OwMw = 70141 053-0631425-569231

  Content Spsys.log: 0 x 80070002

  License data-->
  Software Licensing service is not working.

  --> HWID data
  Current Hash HWID: LgAAAAEAAAABAAEAAgABAAAAAgABAAEAJJT82Wy11kRwlooj8vT2kSg3rFYqhQ ==

  Activation 1.0 data OEM-->
  N/A

  Activation 2.0 data OEM-->
  BIOS valid for OA 2.0: Yes
  Windows marker version: 0 x 20000
  OEMID and OEMTableID consistent: Yes
  BIOS information:
  ACPI Table name OEMID value OEMTableID value
  HPQOEM APIC-SLIC-CPC
  FACP SLIC-CPC HPQOEM
  HPET SLIC-CPC HPQOEM
  MCFG SLIC-CPC HPQOEM
  SLIC SLIC-CPC HPQOEM
  SSDT HPQOEM SLIC-CPC

• Cannot restart after downloading updates

  He has been working for more than 2 years in a satisfactory way, but has now suddenly stopped working for no apparent reason.

  How to solve the problem please?

  Thanks in advance for any response.

  Try a system restore:

  How to use System Restore in Windows 7 [easy, 5-10 Min]

• Cannot use or restore Vista after SP1 uninstall

  original title: cannot use or restore after uninstalling SP1 Vista - please help.

  In order to perform an upgrade of Vista installation to repair the damage caused by a virus recently, I uninstalled Service Pack 1 (because installation upgrade will not work with SP1). I know there are other things I should have done (a sfc/scannow in theCommandPrompt) or SP1 slipstreamed DVD, but I did not know them at the time, nor did I think there will be problems as a result of an uninstallation of SP1. As the title suggests, I got kind of wrong.

  It all started after uninstallation, which seemed successful. I rebooted, and instead to get Vista without SP1, I get an error code of the variety of the command prompt (just the black screen with white writing). This continues for a couple of times, and after a few remedies attempts that fail miserably, I decide to systemrestore(using the Vista CD, of course) at a point before uninstalling SP1. I think it will work, but the first time, as it gets to the "development of restoration" and how he hung for three hours before, I decided to turn off the computer because he was of course not moveable anywhere. I restart and let the boot from HARD drive upwards to see if maybe something worked, and I get to the login screen of Vista, how I notice none of my devices work. The mouse or the keyboard responds (both are USB) and the attempts with the PS/2 versions don't either. I thought maybe it was a driver problem, so I reinstalled the driver chipset at the disk using my laptop (took thedesktopHARD drive, put in a box outside, then executed the installer of the chipset on my laptop and said to install outside driver), but it could not solve the problem. I also tried other restorations, but invariably they fail after a certain point, which gives me an error message:

  "System restore failed due to an unspecified error. The file could not be opened from a transactional point of view, because its identity depends on the result of a unresolved transaction. (0x80071AA7).

  I googled errormessageand see that most people encounter it while trying to install a service pack, I thought it was a problem with restoring Vista without SP1 to Vista SP1. Thusly, I used the command from theVistaCD command-line option to read my Windows Update log and got the following:

  "2010-07-09 04:44:32:593 664 29 c Misc = logging initialized (build: 6.0.6000.16386, tz:-0800) =".
  2010-07-09 04:44:32:593 664 29 c Misc = process: X:\windows\system32\Rstrui.exe
  2010-07-09 04:44:32:593 664 29 c Misc = Module: X:\Windows\system32\wuapi.dll
  2010-07-09 04:44:32:593 664 29 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 04:44:34:605 664 29 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 04:44:36:617 664 29 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 04:44:38:630 664 29 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 04:44:38:630 664 29 ch. COMAPI WARNING: failed to connect to the service. (hr = 80040154)
  2010-07-09 15:26:30:160 216 12 c Misc = logging initialized (build: 6.0.6000.16386, tz:-0800) =.
  2010-07-09 15:26:30:160 216 12 c Misc = process: X:\windows\system32\Rstrui.exe
  2010-07-09 15:26:30:160 216 12 c Misc = Module: X:\Windows\system32\wuapi.dll
  2010-07-09 15:26:30:160 216 12 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 15:26:32:172 216 12 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 15:26:34:185 216 12 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 15:26:36:197 216 12 c COMAPI FATAL: unable to connect to service (hr = 80040154)
  2010-07-09 15:26:36:197 216 12 ch. COMAPI WARNING: failed to connect to the service. (hr = 80040154)
  2010-07-09 16:04:19:912 356 Misc 3 b 0 = logging initialized (build: 6.0.6000.16386, tz:-0800) =.
  2010-07-09 16:04:19:912 b 356 3-0 Misc = process: X:\windows\system32\Rstrui.exe
  2010-07-09 16:04:19:912 b 356 3-0 Misc = Module: X:\windows\system32\wuapi.dll
  2010-07-09 16:04:19:912 b 356 3-0 COMAPI FATALE: unable to connect to service (hr = 80080005)
  2010-07-09 16:04:19:912 b 356 3-0 COMAPI WARNING: failed to connect to the service. (hr = 80080005)
  2010-07-09 16:18:08:745 532 248 Misc = logging initialized (build: 6.0.6000.16386, tz:-0800) =.
  2010-07-09 16:18:08:745 532 248 Misc = process: X:\windows\system32\Rstrui.exe
  2010-07-09 16:18:08:745 532 248 Misc = Module: X:\windows\system32\wuapi.dll
  2010-07-09 16:18:08:745 532 248 COMAPI FATALE: unable to connect to service (hr = 80080005)
  2010-07-09 16:18:08:745 532 248 COMAPI WARNING: failed to connect to the service. (hr = 80080005)
  2010-07-09 16:25:53:894 976 244 Misc = logging initialized (build: 7.4.7600.226, tz:-0800) =.
  2010-07-09 16:25:53:894 976 244 Misc = process: X:\windows\system32\Rstrui.exe
  2010-07-09 16:25:53:894 976 244 Misc = Module: X:\windows\system32\wuapi.dll
  2010-07-09 16:25:53:894 976 244 COMAPI FATALE: unable to connect to service (hr = 80080005)
  2010-07-09 16:25:53:894 976 244 COMAPI WARNING: failed to connect to the service. (HR = 80080005) »

  I can't interpret it, although it seems to confirm my suspicions the transition from other than the SP1 and SP1 is causing issues. If someone else could interpret this?

  Basically I have a non-functional operating system, I can not restore it to a State of operation, nor access the input devices because it does not work on the login screen. Anyone all proposed solutions to the problem, short of a clean install of Vista? I don't want to reformat unless absolutely necessary.

  This is the forum Vista install.

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/threads

  You can try the repair Forum.

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, Acer, recovery disk/s etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/default.aspx/KB/326246

  'How to replace Microsoft software or hardware, order service packs and upgrades, and replace product manuals'

  See you soon.

  Mick Murphy - Microsoft partner

• Explorer Windows restarts after a minute arriving at log on screen or if I connect quickly the dialogue windows Explorer unhandled 0x00000000 in explorer.exe exception States: after repair of Windows XP running.

  Windows Explorer restarts after a minute arriving at log on screen or if I connect quickly the dialogue windows Explorer States of exception unhandled 0x00000000 in explorer.exe: 0CX0000005: reading location access violation) X 00000000 Code: 0XC0000005, flags: 0 x 00000000 after you run Windows XP repair. Repeated repair Windows now for the third time, repair works OK but always produces the result above!. Initially, ran SFC/scannow, he ran very well modified some files but has not fixed the problem. Now I can't run Sfc/scannow in administrator mode in a repair console or environment (cmd) receive error "Windows file protection could not initialize the scanning of protected files. The specific error code is 0X000006ba [the RPC server is unavailable]. Can not access services through msconfig in safe mode, no available tab. When I click on Control Panel in safe mode, I get an error but control then window opens I can access to the services window, but as soon as I click on any service Windows Explorer plunges a black screen with only the white inscription SafeMode visible in each of the corners. When I try to access the sound module in safe mode, I have an error message and he abandoned me in safe mode desktop. Have no tab restore field in system restore to create a system restore point. In safe mode do not log off, restart or shut down (only windows explore drops leaving the black screen with text in each corner indicating the computer in safe mode, no recorded parameters.) Tried to run scanreg.exe & scanregw.exe run, cmd, mode console repair but command is unrecognized. When I tried to run all these commands using BartePe, the States of error cannot access raw disk. In safe mode, I can access the first level for example my computer folder, but when I double click on the c drive or any other drive nothing happens!

  Access msconfig, run, cmd, Device Manager, uninstall programs etc. in safe mode.

  I can easily re - install a new OS on the C partition, but I like challenges! Is there anyone with the skill out there who can offer suggestions for this mother of all XP flaws? (apart from the installation of a new version of Win XP)

  Hi Semi_Tech,

  Step 1: Start the computer and use the Recovery Console to check for errors
  a. see to start the computer and use the Recovery Console
  b. at the command prompt, type chkdsk /f /r and press to enter.

  Step 2: We recommend that you check if the RPC Server service is running.
  a. Click Start, click Run, type services.msc and click ok.
  b. in the list of services, double-click RPC Server service.
  c. change the startup type to automatic and click on the Start button.
  d. click ok to apply the changes.

  See if the steps mentioned by '- MainFrame -' can help you to:
  See windows SFC file protection could not run a scan of protected system files

  Step 3: Check if you can start the computer in safe mode
  a. see the description of the options course in Windows XP Startup Mode
  b. connection to the administrator user account and check if the problem persists.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Now windows vista SP1 installed, still restarts after hibernation

  Right after the installation of SP1 on windows Vista, the computer restarts after hibernation/locking laptop computer

  Hi Jason & florencedefermartel,.

  You can check the manufacturer's website and try to update the Chipset and drivers display and check.

  You can see the manual of the system manufacturer or contact the system manufacturer for more information on how to make the changes in the BIOS.

  Note: Change to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Check out the link:

  Update drivers: recommended links

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-drivers-recommended-links

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer

• Lenovo T61 - 7663-AY2 uninstall Vista SP1 to SP2 and now cannot restart

  Hello community,

  I did something wrong with my Lenovo computer.

  I tried to upgrade vista SP1 to SP2 in order to continue to receive updates from windows, but I failed to improve.

  I read on a forum that to go if you have some difficulties to move from SP1 to SP2, the best thing to do is to uninstall SP1, in order to re-install again and after the update to SP2 is easy.

  So I uninstalled Vista SP1: KB936330 from my laptop and now it cannot restart. I'm facing the famous! 0xc01a001d! registry error.

  I tried all content restoration factory (MS DOS, restoring from the last restore point), but it cannot restart.

  Is there a usual thing do in this case, before the start in the order, he returned with the factory setting?

  My warranty expired on September 21, 2010, and I bought my computer in France while I am in England now.

  Thanks a lot for your help.

  Mitch

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-67853

  Here is the driver matrix which relates to your T61

• This VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure

  ESXI 4.0 3 running virtual machines.

  600 GB HDD / 8 Gigas of RAM / Xenon QuadCore.

  ESXI 5.5 (I had two).

  Using Raid 01 (1 TB)

  RAM of 64 Gbite

  Hearts CoreI5 Xenon proceso.

  VCenter server deployment with Vmware Storage appliance.

  Problem:

  I've had enough material resources, in fact, I had twice the disk space and memory to four times more in the reception of news

  When migrating virtual machines in ESXI 4 server and get Vcentener turn it on the message "this VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure.  "

  I do not understand because the servers have resources, I can't find what is wrong.

  Should I use another method of migration?

  Once that you have migrated, can solve this problem without re-migration of computers?

  I found this post, but it's no imformation. This VM could not become vSphere protected HA and HA cannot attempt to restart after failure of.

  Thank you

  See:

  Re: This VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure.

• Cannot restart the computer after the deletion of XP SP3

  I had a problem with Outlook Express (he would hang whenever I tried to open it) so I thought I'd install Windows XP Service Pack 3 (I'm currently under SP2).  I downloaded and tried to install it.  It has got 3/4 of the way through the installation, and then become immune.  I hit the button cancel, rebooted and everything was normal with the exception of Outlook Express.  Then I went to add & remove programs to see if something was there that shouldn't be and noticed that XP SP3 had replaced my XP SP2 but, system information showed SP2.  I removed XP SP3 using Add & Remove programs and then restarted.  At the start, my computer is going to happen to the Windows XP start screen, the loading bar will go twice on the screen and then the comp goes in another finally restart promping me to choose the safe mode or normal boot upward.  If I choose normal startup upwards, it does the same thing again.  Safe mode works very well.
   
  I hope that there is an alternative to reinstalling windows (but I doubt that it is).
   
  If I have to reinstall windows, how to back up e-mail and address book files?  Should what type of things I write down to make sure I can reconnect to my e-mail server as soon as I did reinstall it?

  Any help is greatly appreciated.

  I was able to resolve my problem starting by calling Microsoft support.  It ends up being a corrupted video driver that caused my computer to boot the system.  The driver has become corrupted when I canceled the installation of SP3 after he become inadmissible.  Microsoft support said it must have updated the driver and when I uninstalled SP3, it must have corrupted the driver.  After 95 minutes on the phone, we have the problem solved.  My problem with Outlook Express is still not resolved and I posted the problem in the forum proper.  I will try to answer the questions you posted in this forum to better inform you of what we are dealing with.  I'll have to do later as I'm typing this from work.

  Thank you for your help.

• The computer was restarted after a bugcheck. The bugcheck was: 0x0000007f

  Get a BSOD on Windows Server 2008 R2 SP1 with "the computer restarted after an error checking.  "The bugcheck was: 0x0000007f (0 x 0x00000000000006f8, 0 x 0000000000000008, 0000000080050033, 0xfffff800018c3484).

  -a ran the system file without error checking

  -a ran diagnostics material without errors

  -all updated hardware drivers

  -windows update updates

  -a ran chkdsk on drives without errors

  I excluded the material with Dell.

  I have the minidumps available if it lights all but check these in the BSOD Viewer, it shows.

  Bug control chain: UNEXPECTED_KERNEL_MODE_TRAP

  Bug check code: 0x0000007f

  Parameter 1: 00000000'00000008

  Parameter 2: 00000000'80050033

  Parameter 3: 00000000' 000006f8

  Parameter 4: fffff800'018 c 8484

  Caused by the driver: ntoskrnl.exe

  Caused by Adresss: ntoskrnl.exe + 75bc0

  Might try to uninstall the AV as another post suggested - will show the result if all of the changes.

  Any ideas what this could be?

  Crash dump...

  The debugging session: 18:40:29.750 Thu Jul 3 2014 (UTC - 04:00)
  System Uptime: 0 days 20:07:06.256

  Loading the kernel symbols

  BUGCHECK_STR: 0x7f_8

  CUSTOMER_CRASH_COUNT: 1

  DEFAULT_BUCKET_ID: DRIVER_FAULT_SERVER_MINIDUMP

  Nom_processus: ledgers.exe

  CURRENT_IRQL: 1

  LAST_CONTROL_TRANSFER: from fffff800018d0169 to fffff800018d0bc0

  Msinfo32.txt

  07/03/2014 17:22 application Error Faulting application name: Ledgers.exe, version: 1.0.0.0, time stamp: 0x2a425e19
  The failed module name: Ledgers.exe, version: 1.0.0.0, time stamp: 0x2a425e19
  Exception code: 0xc0000005
  Offset: 0x0000ad75
  ID of the process failed: 0 x 8940
  Start time of application vulnerabilities: 0x01cf96bab4486883
  The failing application path: C:\Program Files (x 86) \Client\Ledgers.exe Prophet
  Path of the failing module: C:\Program Files (x 86) \Prophet Client\Ledgers.exe
  Report ID: a9efac34-02d6-11e4-a027-a4badb445132

  28/06/2014 18:53 application Error Faulting application name: Ledgers.exe, version: 1.0.0.0, time stamp: 0x2a425e19
  Name of the failed module: KERNELBASE.dll, version: 6.1.7601.18409, time stamp: 0x53159a86
  Exception code: 0xc0000005
  Offset: 0x00014ab0
  ID of the process failed: 0x21c0
  Start time of application vulnerabilities: 0x01cf92d1ba345f0a
  The failing application path: C:\Program Files (x 86) \Prophet Client\Ledgers.exe
  Path of the failing module: C:\Windows\syswow64\KERNELBASE.dll
  Report ID: 866145fa-fef5-11e3-9b5a-a4badb445132