cDAQ Module Question

Similar Questions

• Device vs. cDAQ Module

  I have an executable I don't unfortunately have the LabView vi source for.  The program is used for data acquisition.  It refers to a defined device NI Max (Dev1 and Dev2).  I've been using the software with a combination of 9162 9234/USB USB.  When it is plugged into the laptop, this combination is presented as a DevX NI Max and therefore was found by the software.  We started recently to replace our 9162 modules with single slot CDAQ 9171 modules.  Unfortunately it is plugged into the laptop the software does not recognize this combination of module.  With the original configuration the module 9234 present only as a DevX.  With the current configuration of the module 9234 is a subset of the carrier 9171.  I think that this, why the software does not recognize the new e-mail.  Is there a way I can create a virtual device that will reference the cDAQ module and simulate the original installation?

  In a Word, NO, you must update the code.

• Find channels and cDAQ modules

  I have looked around the previous messages, but can't seem to find what I'm looking for.

  In most of my experience, I've implemented some DAQ and once the modules and channels are all in place, which is where they stay forever.

  Since I know things will not move, I create tasks in DAQmx.

  I'm working currently on a new installation program, but the problem is that in things cDAQ will not be in the same place every time.

  The application must read a number of strain gauges, which will be connected to the NI 9235 modules.

  It will take place anywhere from 1 to 3 modules attached, and they can be in one of the 8 available cDAQ chassis slots 9172.

  In addition, within a given module, anywhere from 1 to 8 channels will be connected.

  So basically, I guess my questions are running:

  (1) how many modules are connected and where?

  (2) in each module, the number of channels is turned on and how much is empty.

  From there on, I use DAQmx palette to take care of things.

  Thank you!

  So with every new start of the program, you will have a known device (your strain gauge device), but unknown channels. Here's how I attacked only a few years ago...

  • DAQmx create a task to create a job.
  
  
  • Make a constant table of all known possible channels. Say that it is 8 cells and compare that to an array of channels USED, making false tracks off the chains 'Unused' and the names of real channel out of used ones. Under certain conditions to check which ones which is used to remove the appropriate channel and add the DAQmx virtual channels properly. The VI snapshot below goes into the details. I brought not only the channels, channels, such as min/max properties and bridge information. My VI also made bridge removal, under certain conditions, depending on sensor that the user wanted to null (that part is not shown.)

  This code isn't super sleek, but I hope this gives you the ideas come from.

  

• cDAQ module signals from 5 to 2000 Hz genarete

  Hello

  I am looking for an output module of the cDAQ which can generate signals of frequency from 0 to 2000 Hz

  Thank you

  Prashant

  Hello, UPRR.

  As long as the module has a refresh rate higher than 20kS/sec, then you should be fine. so NI 9263, NI 9264, NI 9265 and NI 9269 should be good for you.

  Kind regards

• Sampling Multiple channels of unique cDAQ Module

  Hi all

  I am currently researching the use of cDAQ for a system of analysis of oil, especially the module OR 9201 for voltage GOT.

  We have 6 entries SE located in the voltage/current ratings, although they all need different sampling frequencies.  It is my understanding that the module is capable of 500 kHz, which will be split between entries.

  The sampling frequency should divided equally?  Or could I for example send a 250 kHz channel and split the rest between the other 5.  Synchronous between devices is not necessary.

  Many thanks in advance,

  Peter

  Peter,

  See my replies to each ball:

  • Am I correct in saying that I could taste each module to a different sample rate? Yes
  • If I taste the 9201 to 500kHz/6ch, will I have an effective sampling frequency of ~ 83kHz on a given channel? Yes

• Upgrade to version 6.0 SourceFire Module questions

  We have just implemented SourceFire Module version 5.4.1 on our ASA recently, but want to upgrade to version 6.0. I've been through Notes version 6.0 for the upgrade, which are dated to November 2015, but had a few questions that I was hoping someone here could answer:

  -Our FireSIGHT Management Center is a virtual appliance of 64-bit. Can we install version 6.0 on a virtual appliance VMWare running on EXSi 6.0? The only issue date list 5.1 and 5.5 ESXi ESXi.

  -Should what files I use for the update? The Release Notes say to use "SourceFire_3d_Defense_Center_S3_upgrade - 6.0.0 - 1005.sh. My choice on Cisco's Support site are: asasfr-sys - 6.0.0 - 1005.pkg, asasfr-5500 x-boot - 6.0.0 - 1005.img and Cisco_Network_Sensor_Upgrade - 6.0.0 - 1005.sh. I guess the sys-asasfr - 1005.pkg - 6.0.0 is for CME, and the Cisco_Network_Sensor_Upgrade - 6.0.0 - 1005.sh is for the ASAs.Is that right?

  -How long will the update for FMC and ASAs? The ASA is a 5516 x and the release notes look like they say that the update will take about 41 minutes.

  ESXi 6.0 is not officially supported so that your experience may vary. If you get stuck, you may TAC by telling you that you're on your own.

  "Cisco_Network_Sensor_Upgrade - 6.0.0 - 1005.sh" is used to upgrade the fire ASA power module in the Manager of firepower.

  If you were a fabricated construction or reimage then you would use the boot images and sys respectively.

  41 minutes for CME is right. As mentioned Philip, 2 hours is a better estimate of the ASA module, especially on a smaller area as the X 5516.

• LR CC develop Module questions

  Hi all... I write today as I just ran into this issue with the develop module. I have the photographers of CC version that is installed on my machine main home as well as my laptop to the mobile edition. I got the apps installed and working well for a long time. Recently, I upgraded my laptop with a newer machine (I7 Windows based). I logged into my account on my old laptop and machine at home so that I could log on the new laptop. I connected successfully on my machine at home as well as the new laptop. I even edited photos on both machines. A few days ago, I tried importing and editing photos on my laptop. They have imported and I can see them in all the modules in Lightroom, but module development now as completely pink picture area. I rebooted and registered in and the question remains.

  I have attached an image showing the problem and system information. Any help would be appreciated.

  

  Try turning off the GPU.

  Go to Edit Prerences > Performance and uncheck CPU graph use.

• Two Modules questions: Debug & amp; Events

  Hello
  
  I have a question and a question regarding the Modules:
  
  (1) I use the Mac beta version and for some reason when I build a Module project or select the 'Run the Application' option for the MXML Module file, the debug version of the SWF file is not be compiled. As far as I know, the settings that I currently don't prevent that from happening. Anyone has any idea why? I'm puzzled.
  
  (2) if the events are dispatched via a loaded module, the Application loading it can register listeners for events? I can't find a clear answer to this anywhere in the documentation. You would think that this would be referenced somewhere, whether it is possible or not. I really hope that it is possible.
  
  Thank you
  
  Justin

  Hi Alex,

  Thanks for your response!

  What I was looking for to confirm, is that events sent from a Module will be spread through the Application that loaded. I confirmed it works, at least when the Module is implemented in MXML. I tried the same thing by using a module based on ActionScript and had the opposite effect, but that was before I determined why the debug version of my module SWF file was not compiled bein, who was...

  Apparently the debug version of the SWF file is compiled only if your Module is set as the default Application for a project. It may or may not also be a problem to have that Module value to compile in Flex Modules of the Application Properties dialog box. Once I put my Module as the default application and removed from the Flex Modules dialog box, I had the SWF, I needed to debug. Now I need to test this with a Module based on ActionScript, but given the documents for events, unless my ActionScript Module is on the DisplayList, the event will be distributed directly to the target and the Application will not be aware of the event.

  Your example will be great for cases where I need to make an application aware of the user to interact with the components in the Module. Thank you!

  -justin

• Tecra 8100 memory module questions

  Does anyone know if the ram PC133 144 pin for the Tecra 8200 can be used in the Tecra 8100? I think that the Tecra 8100 usually takes PC100 144 pin but I'm having a hard time getting suppliers to tell me about the PC133 so (probably because it is half the price).

  Hello

  The Tecra 8100 uses these memory modules:
  PC100 256 MB (PA3051U-1NME)
  PC100 128 MB (PA3005U)
  PC100 64 MB (PA3004U)

  Also check this site:
  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=7446&ft=m&St=3

• GPS module question

  I am interested in the mini notebooks with GPS module - I would use the netbook instead of my current GPS (one less thing to carry on a trip), but there is limited info on exactly what this integrated module GPS can/cannot do.

  First, HP Navigator software, it's a service to purchase a monthly subscription to?   I found this on the HP website: "the Navigation is free for a trial period of 30 days and requires paid activation after the trial" what?

  Secondly, this navigator software provide the voice directions 'synthesis' or provide audio or is it simply Visual?

  Thanks for all those who respond

  McHP,

  Navigation in the browser of HP is free for a trial period of 30 days and requires paid activation after the trial. I am not sure the speech synthesis.   Marketing of information is here:

  http://h71036.WWW7.HP.com/HHO/us/en/pclc/articles/navigation-mapping-software.html

  The GPS module will be working with other navigation software.

  -wes

• Develop Module Question

  I am a new user of LR.  I have an iMac, OS 10,10,4 and CC PS and LR CC versions.  I really like quick settings that can be made in the develop module.  When these adjustments are transferred to the original photo or the do, they are transferred.  I make the adjustments in LR and then look at the image in the Finder and nothing has changed with the original and there is no copy of the original...  When I opened the photos in PS, it's like start over with the adjustments.  What I'm doing or not doing correctly?

  Thank you.

  This is the concept of LR - not destructive.

  Your originals stay intact. To view the results with an external program, you need to export, where your changes are "cooked."

  Read here: using Adobe Photoshop Lightroom | Export photos from Lightroom

  And here's how to get to PS from LR to edit and return to LR... https://helpx.Adobe.com/Lightroom/help/editing-Photoshop-or-Photoshop-elements.html

• Retractable module question

  Hi all

  My app has a menu, each menu option call a module as:

  public void itemClickHandler(event:MenuEvent):void {}

  {Switch (Event.Label)}

  case 'Betty ':

  loadModule ("ModuleA.swf");

  break;

  by default:

  break;

  }

  }

  public void loadModule(moduleName:String):void {}

  myModule.unloadModule ();

  moduleName = myModule.url +'? DTS ='+ Horodateur_fichier;

  myModule.loadModule ();

  }

  "< s:ModuleLoader id ="myModule"width ="100% "height ="100% "url =" "Home.swf? _ts =" unload = "chkDirty ()" / >

  This particular Module shrinkage. Other modules is not this problem.

  The module will shrink more each time finishing the remote call in data from a loop.

  Here is my module:

  <? XML version = "1.0" encoding = "utf-8"? >

  " < = xmlns:fx s:Module ' http://ns.Adobe.com/MXML/2009 "

  xmlns:s = "library://ns.adobe.com/flex/spark".

  xmlns:MX = "library://ns.adobe.com/flex/mx".

  creationComplete = "init ()" "

  Width = "100%" height = "100%" >

  < fx:Script >

  <! [CDATA]

  public void init (): void {}

  load styles

  this.styleManager.loadStyleDeclarations("styles/styles.swf",true);

  }

  private void refreshData (): void {}

  arrayLength ++;

  If (arrayLength < 4) {}

  SM_RO. GetData();

  } else {}

  sends the data to the datagrid control

  I try without success:

  this.percentHeight = 100;

  this.percentWidth = 100;

  }

  }

  private void getData_Handler(event:ResultEvent):void {}

  //....

  refreshData();

  }

  []] >

  < / fx:Script >

  < fx:Declarations >

  < mx:RemoteObject id = "SM_RO" destination = "ColdFusion" source = "{cfcPath}" = "multiple" concurrency >

  "< name mx:method ="getData"result =" getData_Handler (event) "fault =" FlexGlobals.topLevelApplication.error_Handler (event) "concurrency"multiple"= / >

  < / mx:RemoteObject >

  < / fx:Declarations >

  < mx:Panel width = "100%" height = "100%" title = "{winTitle}" >

  < mx:ComboBox id = number of lines "rmc_cb" = "15" visible = "false" > < / mx:ComboBox >

  < grids: ExtendedAdvancedDataGrid...

  < / mx:Panel >

  < / s:Module >

  I use FB 4.7 with SDK 4.11. Does anyone have the same problem? Is something like this posted before?

  Any ideas?

  Thank you!

  Change width to transform effectively extends the graphics.  Tramsforms are properties of Flash animation at low altitude.  You must find what Flex widget is the cause of the width of the transformation of change.

  If you look at the width of the transformation of the entire parent chain, I guess that at some point transformation from the top parent widths do not change, as the request and SystemManager for sure.  Regardless of the component is the largest and the lowest to change is two places to begin studying.

• Flex Module questions

  Help, please!
  I was not able to locate my apache configuration file during installation!
  I know it's at/etc/httpd on my mac, but how can I do this during installation. I don't think that there is an option to install with terminal? I don't know how to say file system to look at the root of apache of fins.
  
  Can someone please help me to install it. I'm a newbie only to learn, and this will be useful for me.
  Thank you
  John ([email protected]

  Hello Cristian,
  Thank you very much for your help, I really appreciate your help me through setting up this module flex for my Mac'-'

  If any body has any problems with that, send me an email, and I can help out you. Given that Cristian has helped me a lot, I'd be more than happy to help someone else who is having problems with this.

  John

• Not able to read 4000 samples the analog channels of cDAQ module (module NI 9205)

  Please check the chart bloack (FALSE Structure box state a wait with 20ms function) and attached the code (saved in LabVIEW 2015).

  

  On executing the code and using the button 'Trig', I can see only 1000 samples (for each channel) and not 4000 examples.

  Please help me to understand what I am doing wrong?

  Entry of son "4000" to "samples per channel" Schedule VI DAQmx. The default value when unwired is "1000".

• Prepare the form tool module question

  Hello

  I have Adobe Acrobat Reader with a DC pro subscription. When I try to add the tool shape to prepare for my Add ons, I get redirected to a subscription page. When I try to buy the subscription it tells me that I already have a subscription, but is not clear how to add the shape tool prepare.

  Can anyone help?

  You must use Acrobat DC, not Acrobat Reader DC...