Cisco wap4410n

Similar Questions

• I can not connect Dell Wireless 1390 WLAN Mini Card to WAP4410N

  Hello

  I have dell inspiron 640 m with Wireless 1390 WLAN Mini-Card, and it connects perfectly with any other routers.

  but I can't connect it to the CISCO WAP4410N router! I tried several times but no way.

  I can connect IPAD, Samsung Smart tv, Denon portable radio and toshiba PC but not Imy nspiron computer network.

  I think that my WIFI cannot get th WAP4410N IP address!

  Any expert can help me?

  These products are processed by the Cisco Small Business support community. (URL: https://supportforums.cisco.com/community/netpro/small-business )

• SSLv3 WAP4410N is no longer supported in Chrome, Firefox

  Hi all

  I have a Cisco WAP4410N maintenance a small office for the technicians of the drop-in to connect to our LAN, no heavy traffic or fancy management put in place, they don't see it as a wireless access point can connect to the Internet and access a few Samba Sharing.

  Recently I was making mistakes in Chrome and Firefox that SSL version used by the device is longer supported.

  Chrome (v 40.0.2214.111 m).

  A secure connection cannot be established because this site uses a protocol not supported.
  Error code: ERR_SSL_VERSION_OR_CIPHER_MISMATCH

  Since Firefox (v 35.0.1).

  Firefox cannot guarantee the security of your data on 192.168.128.1, because it uses SSLv3, a broken security protocol.
  Advanced information: ssl_error_no_cypher_overlap

  The device is running version 2.0.7.4 firmware, released January 2014, y at - there no way to bypass this SSL error? So far, I was able to connect to the unit using THE 11, but I'd rather solve the problem causing the error SSL rather than using it as a work-around. Has anyone else had this problem?

  Hi guys,.

  problem is solved in firmware that is never released publicly - 2.0.7.6T1 or 2.0.7.6T2 (the two Beta status). These units are already EoL (which means that no new firmware is planned to be released) I suggest you open the service request to a Small Business Support Center (HWC) and ask the last beta firmware.

  Michal

• SG300 - 28 p: POE power drops every few minutes

  Hi all

  We have a SG300 - 28 p which, at intervals between 5 and 30 minutes or more, lower power to all its ports POE-powered and then immediately restores power. Switch logs nothing when this happens other than to record that the ports went down and back up, even with debug logging enabled. Non - POE ports are not affected.

  When the problem started there were only four POE devices on the switch and we are far under our power budget. (During the test, I added a fifth device, see below.)

  Not all combinations of devices cause the drops occur - specifically, it seems that having devices on ports next to each other causing the drops. When the drops occur, absent the increment of POE devices all counters. I noticed this thread earlier here seemed similar:

  https://supportforums.Cisco.com/thread/2165089

  but in this case, he got no power at all in the adjacent configurations, instead of having to drop all the several minutes.

  I am running

  SW06 #sh worm

  SW version 1.1.2.0 (November 12, 2011 time 23:34:26)

  Start the 1.1.0.6 version (date may 11, 2011 time 18:31)

  HW version V02

  I have the 1.2.2.7.6 ready to go new firmware, I will update this when I get a chance to test it. Unfortunately, it's a switch of production, but it's a with relatively few devices to it so far. If need be, I have a sf300 - 48P I can exchange this sg300 ENJOI trials.

  Thank you for anything you might suggest.

  Here are the details:

  -' Phone' is a phone to IP Avaya 4610SW or 5610SW (class 2)

  -"Watchdog" is an environmental monitor IT Watchdogs Watchdog 100 (class 0)

  -"WAP" is a Cisco WAP4410N (class 3)

  All initially due to lack of combination:

  GI10 phone #1

  gi22 phone #2

  dog guard gi23

  WAP gi24

  would result in the POE power to place on all ports, every 5 to 30 minutes.

  I disabled Green Ethernet completely - no change.

  And then made the following tests:

  1. "power never inline" on gi23 and gi24: problem disappeared

  2. 'inline power auto"on gi23 and gi24: problem is back

  3 ' power inline never' on gi23 only: problem disappeared

  4 ' auto of inline power' on gi23: problem is back

  5 ' power inline never' on gi24 only: problem disappeared

  6. "power inline auto" on gi24: problem is back.

  I left gi23 powered throughout the night and it was stable: it's about 10 hours without any problem.

  This morning, tried the following configs:

  08:54 - worked fine

  IG4 watchdog

  GI10 phone #1

  gi22 phone #2

  WAP gi24

  10:31 - added another phone, the problem came back

  IG4 watchdog

  GI10 phone #1

  gi22 phone #2

  gi23 phone #3

  WAP gi24

  10:43 - inappropriate phone #3 to IG11 (next) - problem continues

  IG4 watchdog

  GI10 phone #1

  IG11 phone #3

  gi22 phone #2

  WAP gi24

  11:00 - moved phone #3 to gi8 - suite problem

  IG4 watchdog

  gi8 phone #3

  GI10 phone #1

  gi22 phone #2

  WAP gi24

  11:31 - moved phone #3 article IG 14 - the problem disappeared

  IG4 watchdog

  GI10 phone #1

  Article IG 14 phone #3

  gi22 phone #2

  WAP gi24

  and that's where we left things now are stable for about four hours.

  The following products are the config more later (11:31).

  SW06 #show power inline

  Power-limit based port mode

  Nominal consumed power unit power use threshold traps

  ---- ------- ------------- ------------------ --------------- ---------

  1 of 180 Watts 18 Watts (10%)         Disable 95

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  Article IG1 Auto search low class0

  IG2 Auto search low class0

  IG3 Auto search low class0

  IG4 Auto on low class0

  IG5 Auto search low class0

  GI6 Auto search low class0

  gi7 Auto search low class0

  gi8 Auto search low class0

  gi9 Auto search low class0

  GI10 Auto on low 2

  IG11 Auto search low class0

  gi12 Auto search low class0

  ig13 Auto search low class0

  IG 14 Auto article on low 2

  gi15 Auto search low class0

  gi16 research Auto low class0

  IG17 Auto search low class0

  gi18 Auto search low class0

  IG19 Auto search low class0

  IG20 Auto search low class0

  IG21 Auto search low class0

  gi22 Auto on low 2

  gi23 research Auto low class0

  gi24 - Auto on low class3

  -watchdog:

  SW06 #show power inline IG4

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  IG4 Auto on low class0

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Absent of meter: 4

  Invalid Signature counter: 0

  SW06 #show interfaces announce IG4

  Port: IG4

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  -Phone:

  #show power inline gi10 SW06

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  GI10 Auto on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 465

  Invalid Signature counter: 0

  #show int adv gi10 SW06

  Port: gi10

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  -Phone:

  SW06 #show power inline article IG 14

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  IG 14 Auto article on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Absent against: 0

  Invalid Signature counter: 0

  SW06 #show int adv article IG 14

  Port: article IG 14

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  SW06 #.

  -Phone:

  #show power inline gi22 SW06

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi22 Auto on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 591

  Invalid Signature counter: 166

  #show int adv gi22 SW06

  Port: gi22

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  --also was the watchdog, now empty:

  SW06 #show power inline gi23

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi23 research Auto low class0

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is disabled - detection is in progress

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 587

  Invalid Signature counter: 0

  -wap:

  SW06 #show power inline gi24

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi24 - Auto on low class3

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 607

  Invalid Signature counter: 3

  SW06 #show int adv gi24

  Port: gi24

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no yes no no no

  Resolution of priority - Yes-

  Other useful bits:

  SW06 active spanning tree #show

  Spanning tree disabled mode (floods BPDU) RSTP

  By default port cost method: long

  SW06 #sh worm

  SW version 1.1.2.0 (November 12, 2011 time 23:34:26)

  Start the 1.1.0.6 version (date may 11, 2011 time 18:31)

  HW version V02

  Hi Rich, reference this photo I just drew is a rough interpretation of how a switch 24 ports has guts. Each + block represents a processor. The numbers below represent the port Bank that corresponds to the transformer. Of course, MODULE POE is clearly identified. Each module 12 POE ports for services.

  I think you have a completely different question. If the POE works for 5 to 30 minutes, it can be a problem of layer 1 (bad son) or a different, perhaps material condition being disturbed. If the switch is at fault, it seems more likely to be defective to a unit of buggy.  I did a lot of research on the operation of the switch ASIC, transformer and modules of POE in the cohesion.

  Quite frankly, I think you should go to the 1.2.7.76 firmware, factory reset the device and test all the ports you want using the same equipment. If maintaining the POE fall every 5 to 30 minutes and you are absolutely positive, that it is not a question of layer 1 or a configuration problem on your products, can I just replace the switch.

  

  -Tom
  Please evaluate the useful messages

• Problem with SG-200 and access point on VLAN

  I'm having some problems with the configuration of VLANS on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is able to access the internet when it is plugged into a port that is on the default VLAN (1 PVID). If I plug it into one of the other VLAN then all clients connected to WiFi to lose access to the internet and can not access on the local VIRTUAL network devices. I've used this configuration with a Cisco WAP4410N of first generation.

  I'm not sure if it's something wrong with the way I configured the switch or a problem with the access point.

  The setup I have is:

  Modem/router ADSL (7800N billion)

  |

  -------------------Port 1--------------------

  |                                               |

  |               SG-200 08 |

  |                                               |

  ---3---port 8 - port

  |                    |

  Access point |

  (TP-Link WA801N).

  |

  SF - 100 D

  The port configurations are

  Port Mode PVID membership

  1 general 1 1U, 7U, 666U

  2 general 1 1U, 7U, 666U

  3 general 7 1U, 7U

  4 General 7 1U, 7U

  5 General 7 1U, 7U

  6 General 7 1U, 7U

  7 general 1U 666, 666U

  8 General 1U 666, 666U

  Iain,

  You have virtual local networks put in place on your router? The subnets that you use on each vlan? The router will give DHCP for each vlan?

  The SG200 isn't a fully managed layer 3 switch, it's just a "smart switch" so you can not actually be able to do simply only switch. A sg300 mode layer 3 would be able to do this because it is a fully managed switch.

  If the router is configured with the VLAN, vlan 1 unidentified, the rest the tag, the router-> SG200 port is trunking and the others as access ports on their vlan respective. Once the router is configured, this video contributor forum albums and Cisco employee David Hornstein is very useful to correctly configure the switch.

  Best,

  David

  Please evaluate the useful messages.

• wireless users

  Hi all

  I have this error message on cisco ISE 3315 when authenticate my wireless users.

  "Dynamic authorization failed: 11213 no response received from the network access device.

  I have a cisco ISE 3315

  and my access point is a CISCO WAP4410N without controller (WLC)

  My access point is to enroll in the ISE NETWORK DEVICES.

  Hello

  Standalone ap nit support cost. If you are profiling devices, you can disable it in the deployment settings. You can also disable coa in the admin under the section profiling settings.

• Question of the list of Interface missing after 1 day

  I had met the lack of network interface list & activated cannot display the list of the interface in FogLight NMS after 1 day.

  Currently, my site uses 30 cisco WAP4410N AP devices, so I tried to install foglight NMS in my PC to monitor the flow of traffic to AP. day 1, I was able to visualize all the information sent by 30 AP, SNMP but 1 day later I had met a list of missing network interface edition & cannot display the list of the interface in FogLight NMS.

  Can someone help me?

  Information:

  Model: Cisco WAP4410N

  Compatible SNMP in 30 AP

  Community = public

  set = public community

  SNMP Trap-community = public

  SNMP = trusted host is set to the IP address of my pc

  Given that your quesiton is Foglight NMS, can you please re post it in the NMS community to http://communities.quest.com/community/nms ? In this way our NMS experts can see and respond?

  Thank you

  Golan

• WAP4410N existing other than Cisco network gateway

  Hello

  I was wondering if someone can quickly answer my question?

  I am trying to use my WAP4410N to create a wireless bridge to an existing network that does not contain any Cisco kit. After reading the manual, I tried the bridge WDS wireless solution, which is my router wireless D-Link & MAC address, but there is no option to put in network WPA2 key, I guess I misunderstood how this feature works, & maybe it works with other products of Cisco wireless?

  Thanks in advance to anyone who can shed light on my question,

  Andy

  Sent by Cisco Support technique iPhone App

  HI Andy,.

  Noramlly that configure you WDS Bridge would need to implement WPA 2 personal option under the wireless part, and then click Security.

  Since the SSID and security must be the same, is that were you would enter information. As to make this set your work with a D-Link wireless router, you'll never miss that probably the question were that this wireless device must support WDS. Even then you might also encounter a question having no match wireless chipsets as well.

  More than likely that this configuration will not work for you. I advise to use an other WAP4410n to establish the connection. Rely on what you are wanting to do a WET200 may also work for you since its just fill a wireless network and only use WDS, but I have never tested this connection with a D-link router so I can't 100% guaranteed if this implementation will work as well or not.

  Hope this helps and let me know if you have any questions.

  Thank you

  -Clayton Sill

• Mesh Local WAP4410N

  We have installed three WAP4410N in a G + 1 Villa (two in ground Flooor) and one on the first floor to cover the entire villa with wifi network. We have created two SSID (VOICE and DATA). The DATA of SSID is Visiable at all and VOICE of SSID is HIDDEN. We connect four phones WIFI SIP (WIP310G2) to the SSID VOICE and SIP register to AVAYA IP OFFICE PBX like SIP Extension. When the people are on the move in the WIFI area is the conversion of phone unplug when switching between AP please guide me to configure the AP (WAP4410N) to work as a mesh Local WIFI for looks two SSIDS sarr

  Hello and welcome to the community at the homepage of Cisco!

  You can also post your question on the WAP4410N in the Cisco Small Business Support Community.

  Cisco Small Business Support community have certified expert Cisco interaction to users and all the products of small businesses like the one you are treated here.

  You will need to create an account in order to post in this community.

• using configuration Repeater WAP4410N

  Hello

  I have a network connected directly to a wap4410n device to allow my laptop to comminucate with her wireless. I need an extra blanket wireless added an another WAP4410 as an additional access point to connect wireless to the original WAP.

  However comes as two separate networks and if I connect to the second WAP it won't comminucate with my network device.

  Network device - WAP4410N--><----WAP4410N--->                   <>

  192.168.1.100 192.168.1.244 129.168.1.243 192.168.1.10

  set as defined as reapeater Access Point?

  with option with MAC & SSID of

  connect the main Repeater access point

  Is there a guide of configuration for this sort of thing. I disabled all the securities that I didn't need and everything has fixed Ip addresses.

  Concerning

  Tony.

  Hello and welcome to the community at the homepage of Cisco!

  WAP4410N is now the Cisco Small Business Support Community.

  You will need to create an account in order to post here.

• There is no communication between devices that are connected to the Linksys WAP4410N Wireless access point?

  Hi all

  I have deployed the new Linksys WAP4410N Wireless Access Point and it works fine. Laptop which is connected to the AP may be able to access the internet. It can communicate with AP and also the gateway IP (IP Router) but it is wireless devices are not able to communicate with each other. In the case of peripheral LAN can communicate with wireless devices. Cannot able to share files between wireless devices.

  Please help me solve this problem. Wat could be the problem here. Stage of Wat I have to take to eliminate this problem.

  Advance thanks.

  Thank you and best regards,

  Chandhuru.M

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  The title of security without thread/how do you have isolation set up wireless?

  Insulation wireless (SSID) on the inside must be disabled to allow the computers associated with the same SSID to see and transfer files between them wireless

  Thank you

  Eric Moyers. : | :. : | :.

  Cisco Small Business U.S. STAC Advanced Support Engineer

  CCNA, CCNA-wireless

  866-606-1866.

  Mon - Fri 09:00 - 18:00 (UTC - 05:00)

  * Please rate the Post so other will know when an answer has been found.

• WAP4410n to WAP351 migration

  Hello

  We use the WAP4410n AP device for a long time, but it was interrupted, and now we have bought a PT WAP351 which gives me problems trying to set up the same way as I did with the 4410n. It doesn t seem to suport of WEP encryption (however I see WEP options on the user manual) and also I m note able to get communication when you use the Wireless Client/Repeater option. I ve attached 4 pictures of what I'm trying to do with the new model compared to the 4410n. Is that possible or we had the wrong model?

  VID PID: WAP351-E-K9 V01

  Firmware version: 1.0.0.39

  WAP4410N AP mode

  4410n_apmode.PNG

  

  4410n_wep.PNG

  

  WAP 351 AP mode? I associated with my hand AP but I communication (ping response) to it. Maybe that's not what I'm looking for. Also my network gets collapsed after a few minutes with this connection.

  wap351_apmode.PNG

  

  wap351_wep.PNG

  

  Thanks in advance.

  Hello

  Thank you for the great question. what you see is the result of some recent wireless incorporated standards. You don't see WEP security is because you have selected as the signal 802.11b/g/n. If you change the 802. 11 b/g you will be able to select WEP as the security type.

  I would caution the use of 'WEP' since it is a hack easy encryption and if you want to use the N signal you will only be able to use WPA or WPA Enterprise.

  Hope this helps you.

  Eric Moyers
  .:|:.:|:. CISCO | Pre-sale technical support of Cisco | Expert on wireless

  Please note the useful messages and let know when your question has been answered.

• WAP4410N-wall access point?

  Hello everyone,

  I have a small question about the WAP4410N access point.

  Is it possible to get this access point to a wall or ceiling?

  Are there tiny "holes" in the back of the access point for editing?

  Or is there a 'fixing' to this access point?

  I already read the technical sheets and documentation related to this access point, but found nothing.

  Thanks in advance.

  Kind regards

  Kevin

  Hi Walter,

  Yes... .it can be fixed to the wall

  http://www.Cisco.com/en/us/docs/wireless/access_point/csbap/WAP4410N/Quick_Start/guide/WAP4410N_QuickStartv1.PDF

  See you soon!

  Rob

• integrated macOS Sierra Cisco IPsec VPN does not work anymore (impossible to validate the server certificate)

  Hello

  I just upgraded to macOS Sierra and built-in Cisco IPsec VPN no longer works. When you try to connect, I get a "cannot validate the certificate of the server. "Check your settings and try to reconnect" error message. I use Cisco ASA with self-signed certificates and everything worked fine with previous versions of OS X.

  Please help me, I need my VPN Thx a lot

  I am having the same problem with StrongSwan and help cert signed with the channel to complete certificates included in the pkcs12 file imported to the keychain. It was working properly in El Capitan, but now broken in the Sierra.

• Cisco VPN does not work in the Sierra

  I just upgraded to OS Sierra and the Cisco VPN, I had the installer does connect more.  The Setup looks right into network preferences. When I click it looks like it is trying but stops without asking for a password.

  Cisco VPN client may need to update or re-installed. If she uses the PPTP Protocol, it will not work. Support for PPTP was ignored, because it is no longer considered as secure.