Computer MAC does not connect to the HP 1200 printer

Similar Questions

• I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet.

  Connected to the new router, but locally only.

  Currently, I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet. The small icon to the left of my screen says only: ACCESS: LOCAL ONLY.
  BASICALLY,.

  I have Windows Vista Home Premium, notebook Compaq (Presario CQ60 to be exact)

  I can connect if I use a cable, but its disadvantages.

  I can connect wirelessly with my PC and Ipad. and Internet access.

  I TRIED:
  Various patches microsoft such as resetting TCP, safe mode with network, reset the router. »

  Thank you in advance and we hope you can answer this soon!

  I use an Atheros AR5007 802. 11 b / g WiFi Adapter(Compaq laptop) for the moment so this is useful. Thanks again!
  Someone suggested that I update my wireless driver. I am open to this idea, if anyone can find a safe and legal site with the download.

  Hi Bryyaan11,

  You can check out the link to HP support and try to download the drivers for your wireless card updated:

  Support HP & drivers

  For more information, you can also consult the following article:

  Updated a hardware driver that is not working properly

  You can also check the following items and try the steps:

  Windows wireless and wired network connection problems

  Solve problems, find wireless networks

  Hope this information is useful.

• Airport utility: green points on the AirPort Extreme & Internet; Mini Mac does not connect to the internet.

  Airport utility shows green points on the AirPort Extreme and the Internet, but my my Mac mini does not connect to the internet. IPhones and 2 portable Windows connect very well, and see all the devices on the home network. The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem. I tried to stop and things start back up as if the installation of the internet for the first time. No joy.

  The airport connects using DHCP in Bridge Mode

  The router address is 192.168.80.1

  Address IPv4 is 192.168.80.2

  DNS server is the same as the router, but grayed out

  Mac Mini IPv4 Address is 192.168.80.3

  IPv6 automatically configures

  Also updated the firmware of the airport; no change.

  ISP guy was friendly but puzzled. He started at the top floor level Tech, so I do not know when I hear back.

  Any ideas to fix?

  Thank you.

  Post edited by: en maschera

  but my my Mac mini does not connect to the internet.

  The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem.

  Hello

  Network preferences may be damaged.

  Open the Finder. In the Finder menu bar, click go > go to folder

  Type or copy paste the following text:

  / Library/Preferences/SystemConfiguration

  Click OK, and then move all files in the SystemConfiguration folder to the trash.

  Restart your Mac. See if that makes a difference.

  Your Mac will generate a new SystemConfiguration folder for you.

  Then open AirPort Utility located in HD > Applications > Utilitiies

  Make sure that both Internet and Extreme are green.

  

• My mac does not connect to the wifi unless I turn on the iphone

  My home wifi works great though I have my wifi enabled on my iPhone. But if I have the wifi turned on on my phone, free wifi does not work half the time, unless I wake up my iPhone. I do not use a personal hotspot, or any other type of phone wifi-centric. Just a normal modem and apple airport extreme router.

  My mac is a model of iMac end 2015 running El Capitan (later). Phone is running last sof

  Any ideas how to solve this problem?

  What exactly do you mean by "does not work? What is going on?

• Mac does not connect to the wifi and keeps crashing

  My macbook pro (end 2013) will not connect to my wifi although each device only. Now he has slow veey hone and continues on crashing, doing simple things like a PDF of scrolling. It all started a week or two after the upgrade to OSX El Capitan

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• After update to Sierra, Mac does not connect to the ReadyNAS device

  I have two Macs at home - an iMac and a MacBook Pro.  I also have a ReadyNAS device, which acts as a time for both Machine.

  I've updated the iMac to macOS Sierra.  The upgrade went smoothly, no error reported.  However, once it was up, I found that the iMac has questions is authenticating with the ReadyNAS via AFP (and / or he would authenticate, then delete the connection) and also not able to connect to the service of Time Machine on the ReadyNAS device.

  To be sure it wasn't the ReadyNAS, I went to my MBP - it still works under OS X 10.11 and shows all the problems.  AFP shares are accessible without problem, and Time Machine works as expected.

  Has nothing changed with Time Machine or AFP protocols under macOS Sierra, which could cause this?

  The ReadyNAS is a ReadyNAS Pro 4, running 4.2.28. firmware, if it is useful.

  Thank you very much for your help!

  AFP is not used by Sierra. Try using SMB instead, if your NAS supports. Or contact the technical support of the manufacturer for assistance.

• HP HPE 180 t does not connect to the Internet at startup

  Hoping someone can help, I had 1 cat and 3 service calls to HP with no luck.  It's a whole new HPE 180 t, 12 GB of RAM, HD 10 000 rpm option, GTX 260 card, etc.  It has Intel 82567V-2 Gigabit controller.  I use a Linksys WRT400N router and a new cable modem of Motorola SB6120.

  On the day of arrival only, HP had problems to connect to internet at startup or wakeup.  No doubt connects 1 on each tent 5-6.  I tried everything - reset the cable modem, router, release and renew the IP address, download the new drivers from Intel, etc.

  Very frustrating - and the thing is, I know that the network is working, because my old Dell 8400 is sitting here and it connects every time. It is connected to the same router, as does my laptop Dell 1545, no connection problems at all.

  HP support was not able to help.  So I have a brand new computer that does not connect to the internet 95% of the time.  Any ideas would be appreciated... THX.

  OK sports fans, keep your fingers crossed.  Come back from Wal-Mart, where I bought a router Netgear WGR614v10 to yestertech on sale for $34.98.  Came home, installed and everything works!  HP connects instantly connects Dell computer Dell laptop connects, works of modem cable Motorola...

  Tried everything on, off tension, different combinations of reboots, etc., in order to give it the toture test and hit the wood, everything works fine.

  Then, the last Linksys WRT400N router apparenly, which isn't on the list of recommended routers Comcast, will not work with this computer.  Now that I did a few Google searches on this subject, I find others who say the same thing.  I called an old friend of mine who is a type of network with the Federales and he said, what Comcast told him specifically NOT to use the router WRT400N Comcast internet service.  So go figure...

  I hope that this case is closed, and thanks for the help and suggestions of everyone and stick with me on this.  I hope that this thread will help others.  The largest that I can give to others is to ensure that you ask your ISP first to see if they have a list of recommended hardware!  Ciao...

• I worked on the Web site of our Church and all of a sudden my computer does not connect to the site. I get a message saying that the connection to the server was reset while the page is loading. Can anyone has any ideas on how I fix?

  I worked on the Web site of our Church and all of a sudden this week, my computer does not connect to the site. I get a message saying that the connection to the server was reset while the page is loading. Can anyone has any ideas on how I fix?

  The error message "the connection was reset" can be caused by a bug for the attack of the BEAST fix (browser exploit against SSL/TLS) that the server does not support.

  • [918127/questions/918127]
  • [918028/questions/918028]

• I just installed a new router and now my desktop running Windows XP computer does not connect to the internet.

  Hello

  I just installed a new router and now my desktop running xp computer does not connect to the internet. I know that it is not the router because I plugged the cable into my laptop running 7 and it works fine. When I try to dhcp I get 169..., when I put manually the IP just get no access to the internet and can not ping to the router address. I tried to run the net work Assistant, emptied my dns, disabled all firewals, still nothing.
  Any suggestions?
  original title: connectivity Limeted

  The zero configuration utility works very well. But it is a desktop computer and on cable. All other wired and wireless PC in the office is working well, then it's definitely this PC. He came out of nowhere, I install a network printer on the PC but that's all.

  Your messages are a bit terse, but if I understand correctly

  • You have a router connected to the Internet and multiple computers connected to the router, some Ethernet cable and others by wireless.
  • All but one of these computers can reach successfully from the Internet via the router.
  • A computer that can't browse the Internet is connected to the router via an Ethernet cable.
  • You disconnected the cable between the router and the desktop problem and connected it to a Windows 7 laptop and the laptop connected to the Internet via the router.
  • You haven't seen any error message (except, perhaps, a message on "Limited or no connectivity").
  • You have installed Windows XP Service Pack 3 (or at least Service Pack 2)

  Assuming that all the foregoing is an accurate summary of the situation, I suggest that you do the following:

  Open a command prompt window (start > run > cmd > OK)
  Type the following lines and press ENTER after each line

  Netsh reset winsock catalog
  netsh int ip reset c:\resetlog.txt

  Close the command prompt window and restart the computer.

• I've updated windows and now my computer does not connect to the wireless network.

  I've updated windows security updates and now my computer does not connect to the wireless network.  Until then, it worked very well and even now it will connect through wired connection but not wireless.

  Hello
   
  You can follow below link that can help you to solve your problem:
  How to troubleshoot wireless network connections in Windows XP Service Pack 2
  http://support.Microsoft.com/kb/870702

• My Explorer Microsoft touch does not connect to the computer (Win 8 and 7 or iMac)

  I bought a touch of Explorer Microsoft wireless mouse and cannot understand why the mouse does not connect. The small usb dongle is recognized and the mouse turns works. The optical light is blue and the touch sensor clicks when I run my finger on it. Nothing happens when I press any button of the mouse (without interaction with the computer). It almost seems like its not even connected to the usb dongle. I tried to find out what's wrong with it or with Windows. The mouse itself doesn't simply plug the usb dongle or on the computer at all. It is not a Bluetooth mouse, so there is no button to connect or sync.

  Hello

  As it seems to be a hardware problem, you can check the link for the Microsoft Hardware supported:

  http://www.Microsoft.com/hardware/en-in/support

• Start the virtual machine and wait for WF, does not connect to the computer virtual for Vds (Windows 2008 R2)

  Hello

  See a strange problem with only a Windows 2008 R2 model. When you use the built-in function "Start VM and wait" workflow to start a virtual machine (after conversion from a template either manually, or through workflow) NIC of the virtual machine (I tried VMXNET3 and e1000 times) does not connect to the problem. Vds can be replicated in a different VCenter, so spreading the vds. I also created several models of Windows 2008 r2 and all have this problem.

  If the model is converted and started outside VRO, it gets an IP from and is connected to the VDS immediately

  Tried add/remove the NIC of the model

  Tried to move the comments on different hosts

  Tried to create a new template from scratch

  NOTE: Windows 2012 R2 doesn't have this problem in the same circles, the only constant is the Windows 2008 R2 being started by VRO.

  Anyone seen this before?

  I found this article and it fixed my problem VMware KB: registration or the deployment of a virtual computer model fails apparently a fix a problem in ESX 5.1, 5.5 (I used the option to get around and things are good)

• Laptop does not connect to the internet, office. Both use the same router. Tried troubleshooting, does not. Help!

  I have a desktop computer and a laptop. Both use the same router. The laptop does not connect to the network, but the office has no problem. My wireless adapter on the laptop is on, I tried troubleshooting. I tried to turn it off for 30 seconds then restart him. But nothing is resolved the problem. Any ideas would be helpful! Thank you

  Hello

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• photosmart HP b210a more does not connect to the server.

  I installed this new printer a few days ago and it works wireless laptop problem, phone and pad. So now all of a sudden I can't print wireless. The printer says does not connect to the server if the wireless works. The wireless working on my computer too. Repeatedly, I installed the installer hp for Lion, I installed the drivers from HP on the Apple site.

  Technical specification:

  iMac running Lion

  Mac Book under Snow Leopard

  iPad

  iPhone 3 g

  AT & T Uverse router

  Thanks to anyone who can help!

  The router rebooted, reinstalled again and it seems to work? Don't know what went wrong.

• Samsung Galaxy S3 does not connect to the DELL laptop

  Hello

  I use the operating system Windows 7 Home Premium 64 - bit with the Intel processor i5-2450 M CPU @2.50 GHz. recently the past 4 months, I have observed that Samsung Galaxy S3 does not connect to the Dell laptop

  We could not see the content of Samsung Mobile in the PC. No Popup message is coming

  I tried the options below

  1. connected with different cable to the laptop, the original cable

  2. try with Samsung Kies

  Can you please help us in this regard that I wasn't sure if the drivers problem.

  We have seen the error in the mobile below.

  "Could not find the software on your computer that can recognize your device.service Pack 3, Windows Media Player, version 10 or greater, for Android File Transfer for MAC OS or Windows XP must be installed.

  You can download and install Kies on your http://www.samsung.com/kies computer to synchronize with your device data, back up the data and upgarde your device (Windows and Mac OS are supported). »

  I use Windows 7 and Media player version 12.0.7601.18150.hence was not, of course, why the Samsung Galaxy S3 does not connect to the DELL laptop

  Thank you

  Kalyan

  Hi Kalyan,

  From my research, this error message indicates that you have an old version of Samsung drivers installed on the computer.

  Several clients are faced with this question after that they have updated the version of Android to 4.3, but the version of the driver is not updated.

  I suggest you uninstall all traces of Samsung is installed in the list programs and then reinstall the device drivers Samsung from the link provided in the previous post.

  To uninstall a program see the link below.

  Uninstall or change a program

  Once you uninstall programs related to Samsung download and install the drivers for Samsung devices.