Computer restarts automatically after selecting the Hibernate mode

Similar Questions

• Computer restarts automatically after closing down

  * Original title: when I shut down my pc automatically restarts it? How can I fix?

  When I shut down my pc automatically restarts it? How can I fix?

  Hello

  1. you get any error message? If Yes, what is the full error message?

  2 has there been recent changes made on the computer before the show?

  Please try to update us with the results and the methods provided below.

  Method 1: Open the power Troubleshooter and check.

  http://Windows.Microsoft.com/is-is/Windows7/open-the-power-Troubleshooter

   

  Method 2: Run the clean boot and check.

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Please note: After troubleshooting, be sure to start your computer in normal mode by following step 7.

  Method 3:

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  Follow these steps:

  a. Click Start, type regedit and press ENTER.

  b. navigate to the following location:

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon

  c. double-click "PowerdownAfterShutdown"

  d. then, change to "0" if it's '1' OR

  Change it to '1' if it is '0' and press ENTER.

  Then, restart the computer and after that it restarts, try to quit again.

  If this does not work, make sure that you change the value in regedit back to what it was originally *.

  For more information, see the article and check.

  Turn off your computer properly

  http://Windows.Microsoft.com/is-is/Windows7/turning-off-your-computer-properly

  Let us know if it helps!

• Why my laptop restarts automatically after shut down when connected or not connected

  Hello Sir, I have HP PAVILION DV4 series laptop. I am currently using WINDOWS 7. But since 1 month it appeared the problem, my laptop automatically restarts after you close when it is connected or not connected. After that I end my laptop shut down normally. Any help would be appreciated.

  Hello

  Thanks for posting your question on the Forums of community of Microsoft.

  I would be grateful, if you can provide us with the following information to help us better understand the question?

  1. have you made changes on the computer before this problem?

  2 you receive error messages or codes to the computer restarts?

  I suggest you to follow the below methods and check.

  Method 1: perform the clean boot.

  Place your system in the clean boot state helps determine if third-party applications or startup items are causing the problem. Check this question in the clean boot state.

  Reference: How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135

   

  Note: After the boot minimum troubleshooting step, read the sections "How to reset the computer to start as usual after a clean boot troubleshooting" in the link provided to return the computer to a Normal startup mode.

  If the problem persists, try Method 2.

  Method 2: System File Checker.

  You can run the System File Checker tool and check if it helps. SFC scan will scan system files corrupted on your computer. You can read the following article to use the appropriate System File Checker tool.

  Use the System File Checker tool to repair missing or corrupted system files.

  http://support.Microsoft.com/kb/929833/en-us

  If the question did not resolve, try Method 3.

  Method 3:

  You can view the steps proposed by cavehermitt in the following link:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/Windows-7-computer-restarts-automatically-after/daeb457a-3509-4BE9-a85b-2935c8c3e108

  Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Hope this information is useful. Please let us know if you need help with Windows.

• I installed the software after installation my computer restarts automatically at the start with on screen start

  I installed the software after installation my computer restarts automatically at the start with on screen start

  Hello

  ·         Do you have what software installed?

  ·         You get the error message?

  Step 1: Try the following steps to disable the automatic restart in case of system error:

  (a) restart your computer and start pressing F8 on your keyboard. On a computer that is configured to start to multiple operating systems, you can press the F8 key when the Boot Menu appears.

  (b) select turn off automatic system failure reboot when the Windows Advanced Options menu appears, and press ENTER.

  (c) Please provide the error if you get one.

  Step 2: Check if you are able to start the computer in safe mode.

  A description of the options to start in Windows XP Mode: http://support.microsoft.com/kb/315222

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Whenever I try to go into safe mode, my PC restarts automatically after a few seconds.

  I use Windows 7 Enterprise edition (64-bit)
  Normal mode/start works fine.

  Hi mcalix,

  It is one of the locations where you will be able to disable the auto restart of the system failure. The other location is, as the computer starts, press F8. In the advanced boot menu, select the disable restart automatic option on the system failure.

  I also suggest you check the exact error message you get to do this in the Event Viewer:

  Event Viewer is a tool that displays detailed information about the events important (for example, programs that don't start as expected or updates are downloaded automatically) on your computer. The event viewer can be useful when troubleshooting problems and errors with Windows and other programs.

  For more information, see:

  What are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  Check out this link to open the event viewer:

  Open event viewer

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

  I also suggest to check if Windows 7 is compatible with your computer hardware.

  Whether your hardware is compatible with Windows

  http://Windows.Microsoft.com/is-is/Windows7/find-out-if-your-hardware-is-compatible-with-Windows

  Windows 7 Upgrade Advisor

  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

  Hope this helps and keep us posted.

• Issue to receive the error message "the system has recovered from a serious error" while working on the computer and the computer restarts automatically.

  Original title: The system has recovered from a serious error-

  The system has recovered from a serious error-

  When you work in windows xp home edition, whenever this programe message and stop running and some auto restart machine.

  What is the solution for this?

  Hi Sandeep,

  Thanks for posting your question in the Microsoft Community forum.
  It seems that you have a problem with the error message "the system has recovered from a serious error," while working on the computer, and the computer restarts automatically.
  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  I may need a few more details to better understand the issue.
  Method 1: I suggest following the steps listed in the article and check if it works.
  Error message: the system has recovered from a serious problem
  http://support.Microsoft.com/kb/316424

  Method 2:
  I suggest you analyze your computer by using the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.
  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
  Important: During the scan of the hard drive if bad sectors are found, the scanner tries to repair this sector, all available on which data may be lost.
  You can see the article for more information:

  A "System has recovered from a serious error" message after every restart.

  http://support.Microsoft.com/kb/317277

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• The value of VM to restart automatically after a power failure

  Hello world

  I'm under vSphere Client 4.1.0 and VMware ESXi 4.1.0. I'm having a problem to find my vSphere client where to change the VM to restart automatically after a power failure. When we have a failure someone must manually start the virtual machine. I want that it automatically starts up on its own. Where can I change this to? I looked around the client with little success...

  Thank you for your time and help

  on the ESXi host go to the tab Configuration - setting Virtual Machine power - properties (top right of the customer)

• My computer restarts automatically when I'm Working.How I stop it?

  my computer restarts automatically directly.

  Please help me

  There are 3 main reason for this.
  1. hardware problems
  2 OS error file / Corruptions
  3. software conflicts

  Right-click on my computer and select Properties
  Click the Advanced tab
  In select United Nations parameters to start recovery, click the automatic reboot Option
  Try to use the computer for some time now. Check if the computer restarts now.

  If the computer restarts always there may be some error in some files. Just try to do a repair installation of Windows XP by using the Windows XP CD.

  If you get a BSOD. (Blue Screen Of Death) there may be some hardware problems also. As RAM / mother board failure.   Not all BSOD due to hardware problems.

• Windows restarts when I select the option to remove the program from the Control Panel files

  Windows 7 Home Premium 64-bit installed. System of the down stops and restarts whenever I select the option to remove programs from the control panel. First of all, the problem occurred when I upgraded the version of iTunes. Restoration has solved the problem. Same thing happened when I upgraded my version of PowerDVD. Restored again to solve the problem. Just installed Office 2010 and the problem came back. I don't seem to be able to install software without this problem. Any help gratefully received.

  Hi Rugger,

  Welcome to the community Microsoft and thanks for posting the question.

  This issue could be happen if system files have been corrupted or any third party application conflicts.

  I would suggest trying the following methods and check if it helps.

  Method 1:

  I suggest you perform a SFC Scan and check if it helps.

  Steps to perform a scan SFC:

  a. click Start, click principally made programs, Accessories, and open the command prompt.

  b. type the following command and press ENTER:

  sfc/scannow

  [The command sfc /scannow. analysis of all protected system files and replaces incorrect versions with appropriate Microsoft versions.]

  Once the scan is finished, close the command prompt window, restart the computer and check.

  Reference: http://support.microsoft.com/kb/929833

  Method 2:

  I suggest you perform a clean boot and check if it helps.

  Clean boot will check if any third-party application is causing the problem, as the clean boot helps eliminate software conflicts.

  How to solve the problem by running the clean boot in Windows 7: http://support.microsoft.com/kb/929135

  Note: once you have completed troubleshooting, perform the steps in the step 3: to reset the computer as usual.

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• How can I get my computer to automatically connect to the internet whenever I turn it on?

  Connect computer to internet automatically switch on

  How can I get my computer to automatically connect to the internet? Currently, I have to press Fn F1 to activate the WLAN - not something huge, but a tad boring. Another computer on the same network will connect automatically in setting in motion.

  It is a 'feature' of the particular computer you are using. Take a look at the manual; It may be a setting in the BIOS to turn on the wireless on startup.

• I'm trying to convert a word doc into a pdf file (which I've done 100 times) but now when I connect and press 'convert' after selecting the file it gives me a error message that says "player doesn't have the ability to access this service?

  I'm trying to convert a word doc into a pdf file (which I've done 100 times) but now when I connect and press 'convert' after selecting the file it gives me a error message that says "player doesn't have the ability to access this service?

  Install and use Acrobat Reader DC. You can not use previous versions more.

• My computer restarts automatically while either my antivirus is running - after some time - and sometimes by opening a large site page. It seems that it restarts if perhaps a high load is placed on the cylinder. I have 2 gig Ram. Any ideas?

  I added some RAM

  Hello Plasma squared,

  Thank you for your message.  We will test your RAM and see if there are problems.  Click HERE to run the Windows Memory Diagnostic.  Please let us know the results.  You can also try to increase the size of your swap file.  Please note, do not follow through with this step if your hard drive is or almost.  You will need at least 3 GB of free to perform this function.
  Click 'Start' > right click on 'My computer' > select 'properties '.
  Select the 'Advanced' tab > in course of execution , select "settings".
  Select the 'Advanced' tab > under virtual memory , select "change".
  Select 'Custom size' replace the first size to 1024 and change the maximum size of 2048.
  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Computer restarts continuously after the message "service windows module installation ended unexpectedly.

  My friend was running Vista sp2 comfortably, but now about 3-5 minutes after you connect on the following message is displayed: header: "You are about to be disconnected," containing the "Windows must now restart because Windows Module Installer Service finished unexpectedly." The machine then automatically restarts. It's a never-ending cycle.

  Is there something to do?

  Hello

  Step 1: Disable automatic reboot and let us know if you get an error code.

  (a) restart the computer

  (b) keep tapping the F8 key during the restart of the computer

  (c) select "Disable automatic restart in the event of system failure" using the arrow key and press to enter.

  Let us know the error code, if you get one.

• PSE 13 Win 8.1 will not be installed, "detects the computer restarts" even after the computer restarts

  PSE 13 Win 8.1 will not, install "detects the computer required restarting" even after restarting the computer.

  The Mac version has installed fine on my desktop.  I now want to put the PC version on my laptop.

  Problem solved.  Seems to have been a combination of HP Support Assistant, eager to check updates and Avast2015 are not satisfied with some aspects of the installation.  Ended up uninstalling Avast, installation of PSE 13 and then re - install Avast.

• Vostro 3500 restart automatically after a

  I have a Dell Vostro 3500 which restarts automatically once I have stop my laptop and unplug the power cord.  I also observed that light scroll in "keyboard and device lights" stays on. The only solution I have is to force the judgment that it restarts and then remove the dough every time.

  Wondering if anyone in the forum also seen this sort of question and have a solution.

  There is no error of this combination LED codes in Vostro™.  I also shot "Automatically restart on error" in the Panel.

  Hi riteshgarg,

  I recommend diagnostics currently running on the computer (restart the computer now the FN and the power button). Let the full diagnosis and Note If you find any error message.

  In addition, check in SafeMode with network. Restart the computer and press F8 on Dell logo and select Safe mode with network. Check to see if the same problem persists.

  Waiting for your answer!