Vostro 3500 restart automatically after a

Similar Questions

• Why my laptop restarts automatically after shut down when connected or not connected

  Hello Sir, I have HP PAVILION DV4 series laptop. I am currently using WINDOWS 7. But since 1 month it appeared the problem, my laptop automatically restarts after you close when it is connected or not connected. After that I end my laptop shut down normally. Any help would be appreciated.

  Hello

  Thanks for posting your question on the Forums of community of Microsoft.

  I would be grateful, if you can provide us with the following information to help us better understand the question?

  1. have you made changes on the computer before this problem?

  2 you receive error messages or codes to the computer restarts?

  I suggest you to follow the below methods and check.

  Method 1: perform the clean boot.

  Place your system in the clean boot state helps determine if third-party applications or startup items are causing the problem. Check this question in the clean boot state.

  Reference: How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135

   

  Note: After the boot minimum troubleshooting step, read the sections "How to reset the computer to start as usual after a clean boot troubleshooting" in the link provided to return the computer to a Normal startup mode.

  If the problem persists, try Method 2.

  Method 2: System File Checker.

  You can run the System File Checker tool and check if it helps. SFC scan will scan system files corrupted on your computer. You can read the following article to use the appropriate System File Checker tool.

  Use the System File Checker tool to repair missing or corrupted system files.

  http://support.Microsoft.com/kb/929833/en-us

  If the question did not resolve, try Method 3.

  Method 3:

  You can view the steps proposed by cavehermitt in the following link:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/Windows-7-computer-restarts-automatically-after/daeb457a-3509-4BE9-a85b-2935c8c3e108

  Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Hope this information is useful. Please let us know if you need help with Windows.

• The value of VM to restart automatically after a power failure

  Hello world

  I'm under vSphere Client 4.1.0 and VMware ESXi 4.1.0. I'm having a problem to find my vSphere client where to change the VM to restart automatically after a power failure. When we have a failure someone must manually start the virtual machine. I want that it automatically starts up on its own. Where can I change this to? I looked around the client with little success...

  Thank you for your time and help

  on the ESXi host go to the tab Configuration - setting Virtual Machine power - properties (top right of the customer)

• Computer restarts automatically after selecting the Hibernate mode

  Title: Can't put my computer in hibernation

  Hello
  After that some windows updates I can't put my computer hibernate more. When I put it into hibernation it will restart automatically, I tried a lot of solutions on the net and finally had to re - install fresh copy of windows 7 and it worked for a while, but after a few updates Windows it is no longer possible and I checked the settings and no change, so if anyone can help please do!

  Specifications of the computer.
  CPU i7-2700
  8 GB RAM
  Windows 7 64-bit
  HARD DRIVE 500 GB

  Hello

  I suggest you to check the BIOS settings to make sure that sleep and Hibernate settings are enabled.
  For reference:
  Check why I can't go back to sleep or Hibernate options on my computer? category and check if it helps.

  Sleep and extended: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions
  Note: Changing the BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
  Hope this information helps.

• Whenever I try to go into safe mode, my PC restarts automatically after a few seconds.

  I use Windows 7 Enterprise edition (64-bit)
  Normal mode/start works fine.

  Hi mcalix,

  It is one of the locations where you will be able to disable the auto restart of the system failure. The other location is, as the computer starts, press F8. In the advanced boot menu, select the disable restart automatic option on the system failure.

  I also suggest you check the exact error message you get to do this in the Event Viewer:

  Event Viewer is a tool that displays detailed information about the events important (for example, programs that don't start as expected or updates are downloaded automatically) on your computer. The event viewer can be useful when troubleshooting problems and errors with Windows and other programs.

  For more information, see:

  What are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  Check out this link to open the event viewer:

  Open event viewer

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

  I also suggest to check if Windows 7 is compatible with your computer hardware.

  Whether your hardware is compatible with Windows

  http://Windows.Microsoft.com/is-is/Windows7/find-out-if-your-hardware-is-compatible-with-Windows

  Windows 7 Upgrade Advisor

  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

  Hope this helps and keep us posted.

• Computer restarts automatically after closing down

  * Original title: when I shut down my pc automatically restarts it? How can I fix?

  When I shut down my pc automatically restarts it? How can I fix?

  Hello

  1. you get any error message? If Yes, what is the full error message?

  2 has there been recent changes made on the computer before the show?

  Please try to update us with the results and the methods provided below.

  Method 1: Open the power Troubleshooter and check.

  http://Windows.Microsoft.com/is-is/Windows7/open-the-power-Troubleshooter

   

  Method 2: Run the clean boot and check.

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Please note: After troubleshooting, be sure to start your computer in normal mode by following step 7.

  Method 3:

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  Follow these steps:

  a. Click Start, type regedit and press ENTER.

  b. navigate to the following location:

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon

  c. double-click "PowerdownAfterShutdown"

  d. then, change to "0" if it's '1' OR

  Change it to '1' if it is '0' and press ENTER.

  Then, restart the computer and after that it restarts, try to quit again.

  If this does not work, make sure that you change the value in regedit back to what it was originally *.

  For more information, see the article and check.

  Turn off your computer properly

  http://Windows.Microsoft.com/is-is/Windows7/turning-off-your-computer-properly

  Let us know if it helps!

• Satellite A110 restarts automatically after each stop

  Hello!

  I have the following problem:
  When to stop the system, my laptop while first goes off completely, as you wish, but 2 seconds later, he again. His behavior differs from a usual restart - then will not turn off, it restarts directly. In addition I can rule out software problems, since I've tested with different operating systems and the behavior is the same everywhere. This problem did not exist before, but suddenly occurred and now is it each time.
  Ah, it is also important if the power adapter is NOT connected (i.e. portable runs only on battery), the problem does not occur. If the laptop works on current alternative, the problem occurs, regardless of whether or not the battery is in Notepad.

  Can anyone help? Each index is very appreciated!

  My laptop is a
  Satellite A110-228
  Part number: PSAB0E-00J007GR

  Thank you very much!

  Hi zaez,

  I doubt that the problem is caused by the OS because it doesn t affect the system when it turn off so there must be another reason of this problem...

  Have you attached external devices?
  They could cause such an automatic start

  I also is advised to disable Wake up on LAN functionality in the BIOS and load the default settings.

• S580 Player restarts automatically after I turned off the tv

  When I turn off my TV, it also turns off my Blu - ray player through a kind of hdmi handshake. but for some reason my s580 is going to restart one or two minutes later. Anyone know what setting I'm supposed to solve? or what I'm supposed to do? I tried going though the menus on the TV and the player, not luck.

  Hello

  Welcome to the community of Sony.

  What is the cable used to connect the BD player to TV? The Blu - ray Disc (BD) player turns off automatically if it is connected using HDMI cables to a TV that has the BRAVIA Sync function and the control for HDMI function is set to ON. The BRAVIA Sync function will turn off the BD drive whenever the TV is turned off.

  Also, make sure that the BD player has updated the firmware in it.

  If my post answered your question, please mark it as an "accepted Solution".

• Vostro 3550 restarts automatically (loop) every 3 seconds

  Dell support,

  I have a problem with a laptop Vostro 3550.

  When I turn on the laptop, it just is not started at all but it auto resarts at the same time, every 3 seconds, the screen is black.  The food, fan button, 3 buttons and also the front power indicator will flash during this period. Its the same thing happens when it's on battery and when the power cable is connected.

  I did it while waiting for the following tests:

  1. remove the battery and the power cable and press the power button for 1 min and try to turn on.

  2 remove the battery cmos for 10 min and make the procedure #1

  3. remove the memories RAM one by one and do the #1 procedure.

  4. measure the voltage on the connector of the power adapter (it was 19.3v)

  5. measure the voltage on the power circuit inside the laptop for any potential problems with the laptop on board power connector and it was ok.

  6. I checked all disconnected Ribbon or the cable, but everything was fine.

  Everyone has ideas, what is the problem or what I am doing wrong?

  Thank you

  Eris

  Hello Eris,

  Please write to us

  When the issue started?

  Would it be possible for you to try another hard drive or the hard drive on another machine?

  What about diagnostic? Please run diagnostics from the f12 (allow) menu and let us know.

  We provide system tag #, e-mail address and your name via private message, by clicking on my name in blue and then select send a private message

  Concerning

• When I shutdown computer after a few minutes his restarts automatically

  When I shutdown computer after a few minutes his restarts automatically

  Try this... you can first unplug your cable ethernet and if it does not restart... here may be the problem. The following has worked for me, but I tried not to disconnect the cable first.

  Open network and sharing Center

  In select it left panel > change map settings

  Right click on Local area connection > properties > configure

  Advanced tab

  The title of the property (listbox):

  Select > Shutdown Wake-On-Lan

  In the value (drop down list): (change) turn off

  I hope that helps!

  Jason

• I installed the software after installation my computer restarts automatically at the start with on screen start

  I installed the software after installation my computer restarts automatically at the start with on screen start

  Hello

  ·         Do you have what software installed?

  ·         You get the error message?

  Step 1: Try the following steps to disable the automatic restart in case of system error:

  (a) restart your computer and start pressing F8 on your keyboard. On a computer that is configured to start to multiple operating systems, you can press the F8 key when the Boot Menu appears.

  (b) select turn off automatic system failure reboot when the Windows Advanced Options menu appears, and press ENTER.

  (c) Please provide the error if you get one.

  Step 2: Check if you are able to start the computer in safe mode.

  A description of the options to start in Windows XP Mode: http://support.microsoft.com/kb/315222

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Vostro 3500 automatic dimming of the display?

  Hi all

  I found that my Vostro 3500 (15.6 WXGA LED display) is, sort of, automatically dimming the brightness of the display when the picture on the screen is dark.

  It is very easy to reproduce this: I just put the paper painted in black, and I can see the brightness gradually dim. When I open a window, mainly white, the brightness increases again.

  Is this a kind of "characteristic" (which I can't find anywhere and so no way to turn it off) and noted someone else?

  Operating system is Windows 7 PRO x 64 with the latest drivers from Dell.

  Interesting note: it seems that this behavior is present when Windows starts and loaded graphics driver. During the startup process, when the screen is black, 90% I did not notice the dimming. This would in my opinion a software about the behavior.

  My next test will try with a live Linux, to see if it's really associated Windows or it is somehow in the firmware of the screen.

  Thanks for any suggestions!

  Concerning

  Giulio

  If anyone is interested, I found the answer.

  This is a feature of the Intel HD Graphics drivers, which can be disabled through the graphics card Intel and multimedia control panel, section "Energy conservation", by not checking the "Balanced" profile when on battery or AC power.

  By default, when a battery this profile is selected the gradation is located.

  Concerning

  Giulio

• Satellite A60 restarts automatically displaying a blue screen

  I have a Toshiba Satellite A60 two years old, recently, I noticed a problem where suddenly the computer restarts automatically, in the first, showing a blue screen with white text for a glimpse of a second. Also what difference does update the BIOS?

  Hi Mustafa

  The blue screen of death appears usually due to hardware failure or serious malfunction of software.
  These two issues are possible on your device.
  Please see this FAQ Toshiba on disabling automatic Windows XP restart after a system failure:
  http://support.toshiba-tro.de/KB0/FAQ5B01770000R01.htm

  If the error message appears again, so you can see all the details of this message and then it should be possible to detect the reason why it happens.

  PS: Extra, you can try to recover the laptop with the restore CD provided. Maybe this will solve this problem.

• Want to m6: 10 Windows my laptop restarts automatically when I click on shut down

  Initially, I had the common problem of my computer stops do not after upgrading windows 10. None of the solutions worked for me, I had no MEI version 11, I got the 9.5 version that does not apply to me. My computer always has a black screen while the power light and fan were still on. After that I followed the suggestsed improvements in the HP support, my computer was blocked is no longer about the closure, but won a new. Whenever I click on the windows, then the power then my laptop stop will be closed for a few seconds and then restarts automatically. I don't want to always hold the power button to turn off my computer. I tried also what does the power of sleep button to stop switching and the problem always arises. I also disabled automatic restart if the computer breaks down. I also tried things release so that they won't wake up the computer. I am very confused and that you can find the older forms of windows 7 and 8 only. I can't find anyone with my problem or a solution. Please help me.

  I tried to find aspecific sollution to your problem, but I could not. However, I found a forum of Windows poston with something similar, only on Windows 8. Maybe you can try and check if the sollution they gave this user works for you

  Here is the link:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-performance/Windows-will-not-shut-down-but-restarts-instead/56b2d6f6-5236-4b06-a386-3452506f549d

• Issue to receive the error message "the system has recovered from a serious error" while working on the computer and the computer restarts automatically.

  Original title: The system has recovered from a serious error-

  The system has recovered from a serious error-

  When you work in windows xp home edition, whenever this programe message and stop running and some auto restart machine.

  What is the solution for this?

  Hi Sandeep,

  Thanks for posting your question in the Microsoft Community forum.
  It seems that you have a problem with the error message "the system has recovered from a serious error," while working on the computer, and the computer restarts automatically.
  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  I may need a few more details to better understand the issue.
  Method 1: I suggest following the steps listed in the article and check if it works.
  Error message: the system has recovered from a serious problem
  http://support.Microsoft.com/kb/316424

  Method 2:
  I suggest you analyze your computer by using the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.
  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
  Important: During the scan of the hard drive if bad sectors are found, the scanner tries to repair this sector, all available on which data may be lost.
  You can see the article for more information:

  A "System has recovered from a serious error" message after every restart.

  http://support.Microsoft.com/kb/317277

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.