Computer stops in 3-5 minutes after startup

Similar Questions

• Windows Vista (64-bit) crashes a few minutes after startup is complete. Difficult to get out of the lock start.

  After a Windows updated 12/09/2009 from my computer stopped working.  It starts (without error) and then freeze a few minutes after loading Windows.

  I removed all the updates of Windows since mid-November, but this has not fixed the problem.  I also tried to boot to the last known successful configuration and has followed the procedures of "clean boot upward" found elsewhere on this forum.  None of these actions resulted in necessary corrections.

  Any other ideas?

  Hi lizseh,

  Welcome to Microsoft Answers Forums.

  I suggest you to restore the system to a previous state where it was working fine and check.

  To restore the operating system to an earlier point in time, follow these steps:

  1. click on start toreduce this includes this image, type System Restore in the Search box, and then click System Restore in the programs list. Collapse this includes this image

  2. If you are prompted for an administrator password or a confirmation, type your password or click continue.

  3. in the System Restore dialog box, click choose a different restore point, and then click Next.

  4. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  5. click on Finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  For more information, please visit the link below,

  http://support.Microsoft.com/kb/936212

  Hope this information helped you.

  Kind regards

  Arona - Microsoft technical support engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• General failure on Ping and TraceRT by WAN IP for 15 minutes after startup

  My Windows 7 64 of Profession will expose this problem.

  After startup, it cannot access anything whatsoever outside the local network.  I can ping, DRC and usually access anything whatsoever on the local network, including the router.  But trying to access what anyone outside the LAN does not work.

  Ping Returns the Timeout on the first response, and then general of failure for the other three.

  Tracert immediately returns a general failure

  I am ping IP address, no domain name, is not a DNS problem.

  After 15 minutes or, the problem resolves, and starting the machine works fine.

  Occasionally (once a day or more), it will return to the problem of General failure for 15 minutes, then return to normal.

  The problem does not occur in safe mode with network.

  The problem occurs whether the user is logged on the machine.

  I have disabled the Windows Firewall to try to resolve, without success.

  I also installed McAfee.

  Thanks for any help that anyone can provide.

  CP71

  I would start by removing McAfee and using MSE at least to test.  You can not just disable McAfee, it should be removed and he is known for this type of problem.

  McAffe often contributes to BSOD

  
  

  I remove and replace it with Microsoft Security Essentials

  
  

  http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  http://www.Microsoft.com/security_essentials/

• Computer crashes to 2 or 3 minutes after startup, sometimes said "not genuine Windows".

  Hello!
  I have a Toshiba Satellite L750D. Windows 7.
  Everything works fine when there is 3 months, I bought the laptop.
  A few days ago, it started to happen:
  The computer starts correctly, Windows starts up, watch the user login screen. Everything works well so far.
  This desktop computer, runs Windows as usual. Two or three minutes later, it becomes terribly slow. So slow that just try to open Explorer takes like 5 minutes... Then the situation becomes unbearable, it's as if the computer crashes.
  Then I have to stop it manually (by pressing button On / Off for 5secs).
  In another time, share this problem, it appears at the bottom right of your desktop that the copy of Windows is not genuine.
  I know that it is authentic, I bought the laptop and I have activated Windows correctly. But hey, this is a minor issue and only happens 1/3 of the time I try to start the computer. The main problem is that Pseudo-gel of infinite of Windows.
  Start in Safe Mode does not change the problem at all. It starts well and like 3 minutes later, becomes terribly slow.
  I can solve the problem somehow (running antivirus, etc.) because I can't throw soft...
  Appreciate your comments on this issue,
  Best regards
  Joel Mollering

  Hello!
  Thank you for the comments, but since the computer is a Toshiba, it has a default System Configuration that allows me to restore the laptop in fabric, without having to start windows.
  I did, I lost a couple of files, but now everything is ok.

  Thank you

• Computer hangs for 15-20 minutes after the start of Windows - WinXP SP3

  Whenever I start my computer, once Windows has started (all the desktop icons have appeared), my computer treats something for 15-20 minutes, but I don't know what it is.  It freezes my computer for 15-20 minutes.  I don't have a lot of many software installed and there is no popup windows saying that some updates are being installed.  I have Win XP SP 3.  Can you help me?

  Hi KMForward81,

  ·         Have updates you installed?

  ·         You get the error message?

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not persist in SafeMode with network, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 2: Run the disk check to check for possible errors.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

  For reference:

  How to make a computer faster: 6 ways to speed up your PC

  Slow PC? Optimize your computer for peak performance

• System freeze about 5 minutes after startup. Can move the mouse, but can't do anything else.

  Computer Compaq laptop turned on updates of Windows, firewall Windows, AVG anti-virus, etc.
  He has suddenly frozen 8 months ago - would not respond other than to be able to move the mouse.
  Does not "left/right mouse click" or "Ctrl + Alt + Del" or "power button."
  After a long waiting, pulled out the battery/power supply.

  Restarted in safe mode, was able to run AVG, but froze again.
  Has helped me select the AVG window and move it autour, but nothing else.
  Was not able to click with the right button on the taskbar to make appear the Task Manager.
  Only way to reboot was to remove the battery/power supply.

  Same thing, it is is happening whenever I start.
  System access for about 5 minutes and then freezes.

  I am able to get into the system at the start restore.
  Have a lot of personal photos on the laptop.
  Please provide a solution so that I can extract the photos and then restore the phone to factory settings.

  Thank you.

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1 in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  http://www.Compaq.com/country/cpq_support.html

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  You can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their way of doing recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• the mouse cursor sticks 5 minutes after startup

  I'm not terrible with my mouse cursor.  I start as usual - all seems to work.  Then after 5 minutes the cursor sticks.  I tried to reset then close down and ty again.  Doing this for two days now.

  Hello

  1. when the question is is produced?
  2. you remember to make changes to your computer before the problem?
  3. are you using a cable or a wireless mouse?

  Follow the steps mentioned below and check if the problem persists.

  Step 1:

  Start your computer in safe mode and check if the problem persists

  Step 2:

   
  If the problem does not persist in safe mode, there must be a third party software that is causing the problem to occur, this is why I suggest you put your computer in a clean boot state.
   
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  
  Note: Put your computer in normal mode (step 7).

• Wireless networks disappear minutes after startup

  I start my desktop PC (Windows 7) and everything works fine. I am connected to my wireless router and have access to the internet.

  Then a problem occurs, sometimes only 2 or 3 minutes later, sometimes around 5 or 6 minutes later.
  The computer loses internet access, but remains connected to the network. After a few seconds, the internet is back.
  After a few times, the computer finally loses the connection to the network, and then the network (as well as other networks that were in the range) is no longer there.
  I am currently link this on my laptop which is right next to my office. My laptop is connected to the router wireless (and internet) without any problem.
  I've been struggling with this for a while now and there are only a few hours, I deleted Norton anti-virus with the Norton Removal Tool. No change.
  Map of TP-Link in the problematic PC wireless network is only about 2 years old. I think my next step is to buy a new card netword, thoughts?
  EDIT - I forgot to mention. I uninstalled and reinstalled the NIC several times. No driver updates available.
  I just thought an idea. Before buying a new card, I'll see if I can install this on my brother's PC. So I'll see what happens.

  Hi Mike,.

  You are facing problems with an internet connection in Windows 7.

  Were there any changes made to the computer before the show?

  Please follow the steps from the link and check that it works very well.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-in/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  For all windows questions do not hesitate to contact us and we will be happy to help you.

• Computer does not recognize USB devices after startup XP

  Computer was working fine.  Moved (by car) to another office.  At present, the keyboard will work until the time starts windows XP (SP3); It can control the it function and has a light illuminated NUMLOCK.  As XP starts, the Numlock light turns off and the keyboard is no longer functional.  It is obvious that the keyboard works, and the USB seems to be OK because he has worked with several installed keyboards until XP load upward.

  Any suggestions are appreciated!

  What type of laptop do you have? In the BIOS make you emulation USB is lit and also make sure that in XP right click on my computer got in the hardware Manager then drive and make sure that there is no '? ' marks in the screen of your driver. Otherwise, this looks like a motherboard might be on the fritz...

• Safari keeps closing in 5 minutes after startup

  Safari keeps closing less than 5 min of launch

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Ask the experts in Apple - Safari

  Apple - Support - Discussions - Safari

  http://discussions.Apple.com/category.jspa?categoryID=169 . for the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• AT100s Wi - Fi freeze a few minutes after startup

  The option check Wi - Fi freezes on "off" by its own. Basically it s turn off and freezing while I m using the Tablet somehow.

  Also the hardware buttons like volume + &-aren t working and the power button won t work unless I force close the Tablet pressing long on it.

  Hello

  Set the default Android system back and factory settings and try again.
  Maybe the system is fucked up due to the installation of some 3rd party applications.

• Computer laptop freezing one minute after I turn it on.

  Original title: the laptop freeze

  my computer freezing guard about a minute after I turn it on, ive tried a bunch of different controls and analyses and even removed several things that were recently installed on my computer, I don't see anything else to do to try to fix it, it works fine in safe mode but freezes even with a clean boot in normal mode

  Start the computer in safe mode with network and download and install Malwarebytes (free version for individuals only), updated definitions and run in safe mode. Disable other security software while you do the analyses.
  http://www.precisesecurity.com/how-to/HT-smodewnet.htm
  http://www.Malwarebytes.org/products/malwarebytes_free
  Download and run SuperAntiSpyware (Free Edition)
  http://www.SUPERAntiSpyware.com/download.html

  Are registry cleaners or optimizers system on the computer?

• Key 3 C often does not work for several minutes after the start, the other keys work fine.

  I got am HP Pavilion 17-e049wm Notebook PC product #E0J75UAR for about 4 weeks now.  I bought it refurbished.  A week ago I started having this problem.  3, e, d and c keys do not work when I first start the computer all of the other keys work.  Nothing happens when they are pressed.   Sometimes I will restart the computer and they work again, other times they won't, but often will start working if I left the computer set for about five minutes after the start.

  The computer is spotlessly clean.  I've only used a dozen times or more.  Nothing has been spilled on the keyboard.

  Sounds like software for me, but what?

  I am running Windows 8.1 and no programs are running at startup, with the exception of a program start button, but the problem began weeks after installing that.

  Any ideas?

  FWIW, I called hp. They believed excluded material and had me do a full system restore. Problem persists... The things you own end up owning you they say... I guess it's doubly true if you own a hp laptop. Full day turned... One day closer to death. Thanks Obama.

• MU computer stops immediately after the start-up or attempts repeated; So sometimes minutes after;

  The computer stops immediately after the start, repeatedly or a few minutes after have managed to start it. The error log showed two evenys:

  (1) the service Acquisition of Image Windows (WIA) suspended at startup; (2) the server {81ED811 A1F4E726-8CF1 - 11 D 1-BF92-00600} is not registered with DCOM within the required time.  After restarting the computer, and after installing all of the updates, I installed the last printer; I unplugged the printer and the computer booted immediately!  Does anyone have suggestions, and if I have to update the drivers (hp Laser jet 5 p & hp scanjet 5370C;) How? Please help, frustration to a max; Thank you very much; HeinrichDS

  HeinrichDS

  Recommendation of the Palcouk of sense what is the operating system and is worth a try.  If you're still having problems, then you need to talk to specialists in XP (because it is a Forum for Vista).  In this case, please transfer your question in the Forums of XP to http://social.answers.microsoft.com/Forums/en-US/category/windowsxp where the XP experts will be happy to help you.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• After the updates of windows, the computer stops responding with a black screen at startup of the system

  Original title: Windows XP does not start after the update, no error message

  Has made no changes to the system, but the last thing that happened was an update of Windows security on stop.

  Now when I boot, the BIOS p.o.s.t. shows good HDs, good DVD-Rom, RAM, but Windows never starts, goes just a black screen, HDs are not accessed.

  -F8 does nothing, can't use the last known good Config or Mode safe

  -Change boot order in the BIOS to boot from the Windows XP DVD, hoping to get the recovery console, but the same thing: black screen, no attempt to spin-up DVD or HDs.

  -Removal of mobo battery to reset the CMOS, no joy.

  -Checked and re checked all connections inside.

  -Stripped devices and added one at a time, no joy.

  -Traded-in an old video card in case it was difficult to generate the higher res gfx, no joy.

  I was construction/upgrade / repair my own PC for 3 decades and can usually solve the problem and fix it myself, but this one me completely baffled.

  Any suggestions?

  Hi Cougarific,

  We recommend that you repair your Windows installation in according to method 2 of this article and check the result.
  See computer stops responding with a black screen when you start Windows XP
  

  Note: When you perform a repair installation, it restores the current installation of Windows XP to the version on the installation DVD. This requires you to reinstall all updates that do not appear in this version of Windows XP disc.

  Visit our Microsoft answers feedback Forum and let us know what you think.