Configuration of the network hosts 4ESXi

Similar Questions

• OfficeJet Pro 8500: Officejet Pro 8500 A910 - unable to access configuration for the network folder screen.

  I can't access my webpage "network folder Setup.

  I can access my page main printer very well using the IP of the printer.   I click on Scan up fine, I then click on "configuration of the network folder" and it tries to load and then goes to a screen "ERR_CONNECTION_TIMED_OUT".

  He warned me the first time that he has been using HTTPS and I approved that.  I currently records on my printer set up awhile back and they work fine but must modify and add a little more.

  I tried multiple computers and devices with the same results.

  Thank you

  Chris Gaines

  MALVERN, AR

  Hello @Cgaines78,

  Thanks for dropping by the HP's Support Forums! I see that you run into issues trying to set up a folder network for your HP Officejet 8500 A910.

  Please continue troubleshooting here: scan to a computer, the e-mail, the device memory or the network folder

  This aid? You are now able to set up a network folder?

  Let me know the results. If this resolves the problem please let others know to mark this message as "accept as Solution".  Just say thank you, please click the ' Thumbs Up ' button. If you need more assistance let me know and I will gladly do whatever I can to help.

• "couldn't find any computers configured on the network" on the use of the Dell printer.

  I have a dell v305 printer which worked fine, but now I get a message 'no computer configured on the network' how can I get this fixed? I use the same laptop I always used. If I set up my laptop again how?

  Hi Regina,.

  Please contact the Microsoft Community.

  You have a problem with the Dell printer. I'll help you solve the problem.

  Please see the troubleshooting in the article steps-

  http://www.Dell.com/support/home/us/en/19/product-support/product/Dell-V305/manuals

  You can also run this fixit as well-

  http://support.Microsoft.com/mats/printing_problems/en-us?WA=wsignin1.0

  Please consult these articles for assistance more-

  http://Windows.Microsoft.com/en-in/Windows-Vista/troubleshoot-network-printer-problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  We know if this helps solve your problem.

• JOINT-2: Tips for the initial configuration of the network?

  Hello team:

  I was asked to do a very basic configuration of a whole new JOINT-2 on a CAT6500. According to the documentation, once in the Supervisor´s CLI, I run a 'session' command to the location where the METHOD.

  Once, I follow the wizard to add the IP, mask and gateway. Having this configured, the management interface of module´s should be visible from the rest of the network, but I do not see how this happens, because the module must use one of VLAN switch´s and I haven´t found how it is configured.

  Question: how will this link JOINT itself for layer 3 engine switch´s? I don't see how its layer 2 will correspond to any VLAN available in the host LAN switch...

  Any help will be greatly appreciated

  Rogelio Alvez

  Argentina

  I think what you need to add a command on the 6500 that puts management of JOINT-2 port in a vlan individual.  For example:

  intrusion detection module 9 management access port - vlan 101

  This places the management for the joint-2 card port 9 slot vlan 101.  The host IP that you set on the map of JOINT-2 itself then be valid for that vlan.

  Steve

• How to set up/configuration of the network on virtual servers?

  We just bought the license for vSphere with two processors. I will put up at least three virtual servers on that host computer. Can someone point me to an instruction step by step on how to set up the network so that each guest operating system will have their own unique IP address and/or MAC address? The server is an HP Proliant DL380 G7 with two NIC standard more map of the ILO.

  Any suggestion is appreciated.

  MAC address of the virtual machine is generated by ESXi host when you first power on the virtual machine and the IP address will be assigned by an existing DHCP server or you can configure it manually. Regardless of the implementation of a server as a virtual or physical machine, you generally EF static IP settings to a server system.

  André

• Configuration of the network card for my installation

  Hello

  Host machine: Windows-7, wireless, wired network card network card

  The computer invited: Oracle Linux 6.1

  I want to install oracle on my guest computer database and access it from the host machine. I do not particularly like about sharing this database with all other machines in the network (other than the host and all guest computers created on this server).

  What network card configuration would work better for me?

  My host computer is a portable computer. I plan on using this laptop at home, as well as the work. At home I have access to the wired network and wireless (DHCP) while at work I have access only to wireless (DHCP) network.

  I tried to adjust my VM as NAT & Host-Only network. My VM guest Gets the IP address but I cannot ping the virtual machine to the host using machine VM name. If I use the IP address of the virtual machine to ping, it works.

  Thank you

  Yogesh

  Welcome to the community,

  with the requirements you mention, I would recommend a host-only configuration. Due to lack of DNS resolution, you can configure the host with a fixed IP address in the Host-Only range and add the Oracle VM to the hosts of your Windows system file.

  Use a fixed IP address between 192.168.x.2 and... 127, above this addresses are used by DHCP.

  André

• Configuration of the network on New Installation

  We recently expanded our install ESX and now would like to implement vMotion with our vCenter Server. I'm just trying to wrap my head around a good network configuration. Each server vsphere has 8 shared between the 2 cards network cards. Here's what I thought where a config, I need just comments if this configuration is good or not:

  • 0 - Service Console (on LAN) interface

  • 1 - VM LAN Access (on LAN) interface

  • Interface 2 - iSCSI (on dedicated iSCSI Switch)

  • Interface 3 - VMKernel (on dedicated iSCSI Switch)

  This configuration duplicate the second NIC 4 ports for failover or load balancing. This configuration works, or what I have to do anything? I went through a lot of technical documents and that is the conclusion I came to, but I want to make sure I'm not in the wrong lane before getting everything that the installer.

  vCenter has no access to the iSCSI network unless it has an iSCSI HBA or you will use an initiator of the host of VC software to access its own iSCSI storage - I

  case of the vmotion netwrok that there not to ride on the same network segment iSCSI - it will be enough to find on its own isolated network segment.

  peut

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Configuration of the network during installation Linux4 update5

  Hi all
  
  I would appreciate if someone could help me with a problem I have.
  
  I want to install Oracle Apps 12.1.1 on update Linux4 5 on my own PC. It would not be any other OS on this system so that the system would not for Oracle applications.
  
  I refer to the following website to know how to install Linux for Oracle.
  
  http://appsdba.info/docs/oracle_apps/RedHat/oel4.PDF
  
  According to this document, I should get a screen to set network configuration which I did not. I thought that it would be not only important to configure the network so I worry when I don't have it. But after installing Linux, I couldn't connect to the Internet. Someone told me about a successful Oracle Linux applications, installation you must have internet working!
  
  Is someone can you please tell me why I don't get the network configuration screen during the installation of Linux? OR if there is no other better way to set up the network? I am a beginner in installation of Linux and Oracle, and need some more will certainly help in the future. Thanks a lot for your help in advance.
  
  Kind regards
  Anshul

  According to this document, I should get a screen to set network configuration which I did not. I thought that it would be not only important to configure the network so I worry when I don't have it.

  Didn't get what? What stage are you talking?

  What is the entry that you have in the file/etc/hosts? What is the output of "ifconfig - a"?

  But after installing Linux, I couldn't connect to the Internet. Someone told me about a successful Oracle Linux applications, installation you must have internet working!

  That's not true, and you don't need to have an internet connection for Oracle EBS work. However, if you install on a virtual machine, you should be able to access the internet from the computer asked if the host computer is connected to the internet.

  Is someone can you please tell me why I don't get the network configuration screen during the installation of Linux? OR if there is no other better way to set up the network? I am a beginner in installation of Linux and Oracle, and need some more will certainly help in the future. Thanks a lot for your help in advance.

  Again, thank you for mentioning the steps you are talking (including the page number).

  Have you reviewed the steps described in the official Oracle EBS Installation documentation?

  Oracle E-Business Suite installation and upgrade version Notes 12 (12.1.1) for Linux x 86-64 [ID 761566.1]
  Installation of Oracle E-Business Suite and 12 (12.1.1) for Linux x 86 version upgrade Notes [ID 761564.1]

  Thank you
  Hussein

• Need help with the configuration of the network

  Hi all

  I'm confused about the installation of small for networking

  The scenario is I have VLAN 1 and 2 VLANS configured on the same switch. VLAN 1 is on ports say 1-10 and VLAN 2 is on Ports 11-20. Now ESX server is connected to port 1 in VLAN 1.

  Two VIRTUAL networks are allowed to talk to each other. On OS the comments residing on the ESX Server, it will accept the IP address of the subnet to VLAN2 if ESX is not connected to VLAN 2 physcially.

  I know linking the physcially to VLAN 2 ESX Server will succeed, but this can be a possiblily, wont switch be smart enough to talk internally to two VIRTUAL networks. BTW, the switch is a dell connect 5448 switch.

  Anil Gupta

  Don't be afraid of change, his constant in life, reduce your footprint... Go green

  If you have found my reply to be useful, feel free to mark it as useful or Correct.

  Looking for a Virtualization Solution, look here...

  http://www.sky-v.com

  I've attached a picture to show the configuration of my ESX laboratory machine. vSwitch0 contains the service console and vmkernel on the first network on the host port. vSwitch1 contains two VLAN with ID 206 and 208 on the second network port. The name I gave (Labb and server) is what identifies these VLANS when you set up a guest vm networking later. If you are unsure about the ESX networking, then it might be best to try this outside hours of office or on a separate machine. If you change the physical or virtual switching configurations you may interrupt the virtual machines (especially if of data warehouses using an iSCSI or NFS) so be careful.

• HP Officejet Pro 8500 A909a USB 3 questions about the configuration of the network - port USB3 problem

  Fujitsu Windows 7 laptop (all USB2)

  used the full software and installed a printer HP Officejet Pro 8500 A909a Series as a network printer.

  The printer installed fine and don't have USB connection

  All the software and scanning twain installed, so I was able to scan the copy etc.

  I could browse and choose my PC from the front panel of the printer

  However, it was Tuesday confirmed to a friend that their printer would work on a new laptop - bought the laptop

  Fujitsu - but more recent model with 3 USB ports

  I have install and then used the same FULL configured driver to be installed (V14)

  selected as a network printer and then, during the installation, I get an error hardware error USB and USB drivers

  All the USB works, that I've used - BUT the printer is networked and no USB used

  tried to download the driver and install it-exactly the same question

  SO I configure using the devices and printers 'add printer' network and installed

  I can print OK

  BUT no analysis facilities

  and on the façade - cannot see the new PC to scan to

  The only real difference, is that this PC has USB3 and only mine has USB2

  DO not know why on a network installation USB even when searching for

  It's a problem because Drivet package not has not been updated for USB3 - y at - it a patch?

  Thanks for any help / advice

  Hi etaf,.

  I guess the short answer is: Yes, the problem with the software and the 3.0 Port.

  The long answer with a possible work around is as follows: first of all, the software looks for minimum requirements. Because the software is older, he doesn't know what a 3.0 port. You are right when you say that it should work since you do not use the USB and use wireless instead, but this is not the case.

  There is something we can try, but I can't guarantee it will work. I thought first we could connect a USB cable and run the software made to force the software to see the USB port, but then the software wouldn't even get far enough because you can't plug the cable to the most later in the installation.

  My second thought and most promising suggestion is to connect the USB cable (although we do normally not until the software prompts us to) and use the installation wizard HP Print to get the insteaad of software to use the CD or download from the printer driver page. Still, I can't say with certainty that it works, but I don't see why it would not be worth a try.

  If it works, and we get the software installed you can convert the USB connection to a wireless connection using the software. Fingers crossed! Download and run the with the following link. Printer HP install wizard for Windows

  If this does not work, or you don't want to bother with it (not worth trying), I might consider getting a new model of the printer. You can even call HP. They might be able to offer a discount on a newer model. If you are in the Canada, U.S. dial 800-474-6836 or you can Contact HP worldwide.

• Cannot install "analysis to the configuration of the network folder.

  I have a HP Office Jet Pro 8600. I'm a network using a router and an ethernet cable. I am connected to a laptop running Windows 7 IBM. Printing works fine on the network. Scanning works fine on a USB device. My problem is when you try to configure the scanning of documents to a network folder. When I run 'save and test' I get the following error...

  Error. Your printer cannot connect to the server. Press 'Back' to correct the server name and address. Make sure that the network discovery and file sharing are turned on. These settings are in the network and sharing settings in the Windows Control Panel on your computer.

  The directory is not set to read only.

  The network discovery and file sharing are turned on.

  I'm not using Norton Antivirus.

  Can anyone help?

  NJU salvation,

  See pages 53 & 54 of the user guide.

  http://h10032.www1.HP.com/CTG/manual/c03026243.PDF

• OfficeJet pro 8600 + scan if there is no configuration for the network folder

  The printer is wireless to my router and I connect to a computer connected to the router with an ethernet cable.  The computer is running Windows 7SP1 Home Premium 64.

  During the original installation of the printer 3 days ago, I used the wizard set up 'scan to a network folder' a record 'scans public '.  He created the 'profile' correctly and worked well the first time I scanned (I scanned the 3 or 4 times with different tweaks to experiment).  However the next day it no longer worked error on the printer was, 'could not connect to \\Computername\Public scan. Check that the remote computer is on. "Obviously, the computer was on, some communication problems only happened from one day to the next day, he was sitting unattended.  Hmmmmm.  Note that the option "Scan to Computer" works very well, so communication is simply no "scan to network folder" option and I really want to scan to a network folder.

  I went in a private "Scans" folder on my account and created a share as 'DadsScans', creating permissions and following all the tips I've come across so far.  Then I tried many times with the wizard to create a new configuration in the profile and all have failed and yes I found the network and turned on file sharing.  Also remember that it worked fine the first night?

  I tried to enter the local path to the folder (C:\users\dad\My analysis) with a share name (DadsScans), but the error message after choosing the option "test and save" was, "error.  Your printer cannot connect to the server.  Press 'Back' to correct the address and the name of the server.  Setting is not saved. »

  I then tried to enter the share name directly in the path of the network folder, like "\\computername\DadsScans", but the error was "error.  Your printer cannot connect to the server.  Press 'Back' to correct the address and the name of the server.  Make sure that network discovery and file sharing are turned on... "Note, I also tried,"\\computer Address\DadsScans IP"and got the same error.

  Finally, I disabled my firewall and my anti-virus in real time and tried again and got the same error messages.

  Once again, my network discovery and file sharing are on and it worked fine the first time I've used suggesting that everything was fine.  What happened during the night, so that the printer and computer sitting idle?  I've changed NOTHING!  Any suggestions would be greatly appreciated!

  Well well, after several hours of attempts to solve the problem, the 'light bulb went on!  The night after that I configured the "scan to network folder" option, we had some difficulties with our network so I reset our modem and DSL router.  Who cleaned the problems of network with devices.  It is apparently broke something with the communications between the scanner and the computer.  A simple re-start the computer tonight and wa - la, the original public scan I configure worked again and I could create new profiles of "scanning to '!

• Access to a virtual computer within a NAT configuration on the network

  Is it supported or not supported methods to access a virtual machine which is within an instance of fusion on the network?

  For example, say that my VM is 192.168.168.34

  I can understand which port is used for NAT translation somehow (i.e.i 4598) and then launch access to this virtual machine across the network using 192.168.168.34:4598?

  Otherwise, any other ideas on how to make this work?

  Hello

  You can redirect the single ports between the host and the VM.

  So if you want access to the X application on your virtual machine, you need to know on which port that the application is listening and forward this port from your host to your virtual machine.

  There was formerly a nat.conf file, located in Library/Preferences/VMware Fusion/vmnet8/in older versions of Fusion, where you can set up port forwarding. Don't know if it's always the right path, as I have no mac here.

  Tim

• "the network is not present or started" after the execution of the configuration of the network. Why?

  I have a laptop that I used it on a network of small business with printers shared running a Microsoft network.   I was able to see the hard drives, printers, files and folders on the other machines for the past year, without problem.

  I recently installed Norton Internet Security Suite and since this operation were not able to connect to the local network< but="" i="" have="" full="" internet="" access. ="" i="" can="" see="" the="" router="" and="" surf="" the="">

  When I click on the already mapped network Drives (Y and Z on my computer) I get the following popup error:

  An error occurred while reconnecting Z: to \\servername\mydirectory

  Microsoft Windows Network: The network is not present or started.

  This connection has not been restored.

  So I tried to debug as follows.

  I called Norton.  They compeltely uninstalled after internet security and reinstalled using smart firewall.
  (It does not)
   
  I disabled Norton and tried to update the drive netowrk / reconnection
  (It does not)

  I disabled Norton and represented the Network Setup Wizard. Rebooted, tried to reconnect
  (Which did not).

  whenever I tried to connect, the error message.

  If the Windows network turned then how can I access the network?

  I don't see all the computers on the network.
  I can not connect to the printer, I was connected previously.
  The drive mappings, I set up back same Netowrk not started error when I click on them.
  There is no other computers on my network
  I have the same workgroup name (MSHOME) as other computers that CAN share resources.

  I use a Compaq Presario M2000 laptop
  Running Windows XP Home Edition (SP 3)
  trying to connect to a Waindows XP Home w / shared desktop printer.

  Thoughts, suggestions?

  Found the answer

  A friend who did the same thing.

  Notes: Microsoft Windows Network: the network is not present or not started

  
  "I started to see this message on a Windows XP SP2 computer, but not on the other in the same room. I couldn't understand why it was happening I was watching the Samba server to connect, and the machine was not connect at all. In addition, this specific message was not really on the Web.

  The answer is quite simple - run services.msc and enable the Workstation . I had turned off, rebooted and forgotten on this subject. »

  found the answer here:
  http://perljam.NET/notes/Microsoft-Windows-network-the-network-is-not-present-or-not-started/

  DOH

  My apologies.  I'm REALLY surprised that I couldn't find the answer on the forum to help here.  But now, it's here.  Hope this helps someone else who has the same problem and cannot find the solution.

• Please advice on the Configuration of the network and possibilities.

  Hello

  I have a small office at home (me, my wife and 2 employees) and I need to improve my network. It's simply not up to the task.

  Which must be supported:

  • 5 PC desktop
  • 2 notebooks private
  • 2 network printers
  • XBOX
  • NAS
  • Many mobile devices
  • ADSL internet connection
  • Connection internet optical fiber (glass)
  • System network audio (Sonos)

  Right now I use a combination of routers/switches of different brands, and I want to spend it again all devices, all from a brand. That's what I want to do:

  • A wired router to handle the traffic internet ADSL and fiber
  • Several access points wireless (1 device with multiple SSID) or multiple devices: a client, a desk, one for home, one for...
  • Home network of offices on a separate subnet from the network
  • Router must be able to act as an OpenVPN client and tunnel specific IP addresses / ports LAN from the intranet to the VPN service provider (it of to hide my IP address, mainly for private use, not for torrenting, right to privacy)
  • Currently, there is no need to be able to Dáil from outside the office, this could change in the future

  I was thinking to buy the following:

  • LRT224
  • 2 * LAPAC1750 (since the home + office is large enough)

  I reuse a switch 8 ports business grade, no need to replace it.

  My setup is as follows:

  ADSL Modem (bridge mode)-\ /-LAPAC1750 for office and clients (2 SSID)

  > - LRT224 -

  Fiber connection-/ |       \--LAPAC1750 for House- + - OpenVPN connection

  |                                |

  Switch 8 ports (company) + - direct connection

  After reading the manual for both devices, I think that the wireless access points are more then adequate for the task. However, I have my doubts about the LRT224. Yes, it has dual WAN, so perfect for the routing of traffic ADSL or fiber. But the OpenVPN part is not what I need. I need something that is offered by the tomato/DD-WRT flashes for all-in-one routers: OpenVPN client build-in and able to route specific traffic through the VPN tunnel.

  My question is: is this, I want to install, possible with devices metntioned, including a tunnel (via AirVPN) OpenVPN implementation to route the traffic/specific devices through, and multiple wireless access points.

  I hope some of you can help me here. I won't buy an all-in-one wireless router, since a problem with these devices lies between offten, and I like the look and feel of Linksys devices.

  Thanks in advance.

  With sincere friendships.

  Sjoerd

  Edit: fixed formatting and some typo

  LRT routers don't tunnel VPN vendors like the Open Source router firmwares.