Connection of customer Cisco VPN to work

I recently picked up 1 billion domestic 7800N router to replace my old netgear which fell signal much.

I seem to have some access to my work via VPN client network problem.  I can't connect the Cisco VPN client to the network ok but I have no access to the email server and exchange. I tested the parameters of the client on my old Netgear and it works fine. That tells me that the management of the router...

I don't have any packet filtering on and I put in place profile of my fixed ip of internal House on the ip of the work to allow any protocol and any port.

I also sent port 500, 4500 and internal 10000UDP to my ip address.

I'm a noob when it comes to networking and I'm a little lost. I feel this topic falls in the middle ground between the client and the seup router if I appreciate draw my having a definitive answer. I can post a copy of the customer logs if this is useful.

I hope someone can point me in the right direction...

Thank you

Neil

Hello

It looks like your home network is using the same ip as your work network range. I recommend you to choose a new range for your home network that is not identified in the routing table updates in your newspapers.

For example: 10.255.255.0/24

Best regards

Ju

Sent by Cisco Support technique iPad App

Tags: Cisco Security

Similar Questions

  • Unable to connect to the Cisco VPN you use native client: El Capitan

    I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."

    When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:

    * connect using the old work VPN connection: without success

    Config: Hand [server address, account name],

    AUTH settings [shared secret, the Group name].

    Advanced [mode to use the passive FTP = TRUE]

    errors:

    "authd [124]: copy_rights: _server_authorize failed.

    "raccoon [2580]: could not send message vpn_control: Broken pipe"

    ...

    * Add new VPN connection using L2TP over IPSec: without success

    Config: Hand [server address, account name],

    Authentication settings [user authentication: password, identification of the Machine: Shared Secret].

    Advanced [send all traffic on the VPN = TRUE]

    errsors:

    "pppd [2616]: password not found in the system keychain.

    "authd [124]: copy_rights: _server_authorize failed.

    ...


    * Add new connection using Cisco via IPSec VPN: without success

    Main config: [server address, account name].

    AUTH settings [shared secret, the Group name].

    Advanced [mode to use the passive FTP = TRUE]

    errors:

    "authd [124]: copy_rights: _server_authorize failed.

    "raccoon [2580]: could not send message vpn_control: Broken pipe"

    VPN server is high and does not work and accepts connections, this problem is entirely on the client side.

    I. Journal of Console app existing/Legacy VPN connection:

    26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics

    26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]

    26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status

    26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.

    26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

    26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

    26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 339 [2580]: connection.

    26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

    26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

    26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.

    26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 405 [2580]: connection.

    26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

    26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

    26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

    26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

    26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

    26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

    26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

    26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

    26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.

    [26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting

    26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).

    26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

    26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

    26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

    [26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no

    26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    $VPN_SERVER_IP

    II. new VPN connection using L2TP over IPSec Console app log:

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856

    26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856

    26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13

    26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent

    26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

    26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

    26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]

    26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status

    26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory

    26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]

    26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller

    26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller

    26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.

    26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.

    26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain

    26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!

    26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!

    26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501

    26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback

    26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback

    26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed

    26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify

    III. New connection of Cisco VPN through IPSec Console app log:

    26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

    26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

    [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]

    [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status

    26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.

    26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed

    26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

    26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

    26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 296 [2576]: connection.

    26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

    26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

    26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 374 raccoon [2576]: connection.

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

    26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

    26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

    26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

    26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

    26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

    26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

    26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

    26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.

    [26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting

    26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).

    26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

    26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

    26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

    [26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no

    26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    It seems that I solved the problem, but I'm not sure it helped.

    After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.

  • Help: Customer Cisco VPN & Split Tunnel but not Internet

    Hi Forum.

    We are faced with this problem: after having successfully open a VPN connection with the Cisco VPN Client to a router Cisco, the rest of the world are not properly available more.

    This is what has been verified / so far attempted to identify the problem on a Windows Vista computer:

    -Router: Split Tunneling is allowed according to sysop

    -On the VPN-Client: "allow Local Lan access" is checked

    -On the Client (statistics): only STI VPN-rout configured listed unter "guarantee routes." "Local Lan routes" is empty.

    -Calling 'http://www.google.com' in IE fails

    -Call ' 74.125.232.116' (IE IP) IE works / ping the IP works.

    -nslookup properly lists the current DNS server

    -nslookup www.google.com resolves correctly the name of intellectual property

    It seems that it is not that the connection with the rest of the Internet is deleted, but DNS resolution fails somehow, even though all signs point to the appropriate DNS server is in force and although the command line can resolve the name.

    does anyone have a tip how to debug this correctly?

    No worries Pat...

    Sent by Cisco Support technique iPhone App

    -Please evaluate solutions

  • Unable to connect via the Cisco VPN Client

    Hello

    I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

    I am not able to connect and watch the journal on the SAA

    ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

    ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

    ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

    What could be the reason.

    Concerning

    Hi, I had this same problem, here is the solution:

    When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

    Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

    Well, change your strategy using MD5 isakmp / OF would do the trick.

  • Unable to connect to the Cisco VPN using the branch line

    Hello

    We use Cisco VPN Client 5.0.07.0290 to connect to our servers. We have a Sonicwall NSA2400 FW and we have 2 ISPS. We have configured load balancing on firewalls in mode 'Spill-Over '.

    So whenever the 1st line is on full charge, it will automatically moves users on the 2nd line.

    The problem that we face here is the users who get 1st line ISP, they can easily connect to the client VPN Cisco IP, but the users who receive the IP of the 2nd line of the ISP, they are not able to connect to the Cisco VPN Client. It's really annoying because everyone should be able to connect.

    It will be really great if someone can help me as well.

    Thank you

    PS: If Exchange us the line of Sonicwall haapens scenario of Vice versa as mentioned above.

    Hello Sam,.

    Correct me if I help you,.

    In your network that is inside the firewall, you are trying to connect to Cisco VPn client resides outside your network/Public network.

    If the above is the question.

    Please check the routes and roads of sonicwall priority.

    example:

    Isps1: the value of the metric as 1 for traffic destined for cisco VPn IP of the gateway and specify to leave traffic isps1 interface

    ISP2: set the metric 1 once again for the traffic to cisco VPn IP of the gateway and specify to leave traffic ISP2 interface

    interface metric 1 source destination

    Kindly, please note the useful messages and.

    Thank you

    Srikanth

  • Error of customer Cisco VPN connection ASA 5505

    I am unable to connect to the vpn I created on my ASA 5505 using the Cisco VPN Client on a Windows machine. The log of the vpn client and the config of the ASA 5505 is lower. Any help to solve this is appreciated.

    CISCO VPN CLIENT LOG

    Cisco Systems VPN Client Version 5.0.06.0160

    Copyright (C) 1998-2009 Cisco Systems, Inc.. All rights reserved.

    Customer type: Windows, Windows NT

    Running: 6.1.7600

    Config files directory: C:\Program Cisco Systems Client\

    1 09:34:23.030 13/04/11 Sev = Info/4 CM / 0 x 63100002

    Start the login process

    2 09:34:23.061 13/04/11 Sev = Info/4 CM / 0 x 63100004

    Establish a secure connection

    3 09:34:23.061 13/04/11 Sev = Info/4 CM / 0 x 63100024

    Attempt to connect with the server "71.xx.xx.253".

    4 09:34:23.061 13/04/11 Sev = Info/6 IKE/0x6300003B

    Attempts to establish a connection with 71.xx.xx.253.

    5 09:34:23.061 13/04/11 Sev = Info/4 IKE / 0 x 63000001

    From IKE Phase 1 negotiation

    6 09:34:23.077 13/04/11 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 71.xx.xx.253

    7 09:34:23.170 13/04/11 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = 71.xx.xx.253

    8 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

    9 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

    Peer is a compatible peer Cisco-Unity

    10 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

    Peer supports XAUTH

    11 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

    Peer supports the DPD

    12 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

    Peer supports NAT - T

    13 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

    Peer supports fragmentation IKE payloads

    14 09:34:23.170 13/04/11 Sev = Info/6 IKE / 0 x 63000001

    IOS Vendor ID successful construction

    15 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000013

    SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) at 71.xx.xx.253

    16 09:34:23.170 13/04/11 Sev = Info/6 IKE / 0 x 63000055

    Sent a keepalive on the IPSec Security Association

    17 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000083

    IKE port in use - Local Port = 0xEB07, Remote Port = 0 x 1194

    18 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000072

    Automatic NAT detection status:

    Remote endpoint is NOT behind a NAT device

    This effect is behind a NAT device

    19 09:34:23.170 13/04/11 Sev = Info/4 CM/0x6310000E

    ITS established Phase 1.  1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

    20 09:34:23.170 13/04/11 Sev = Info/4 CM/0x6310000E

    ITS established Phase 1.  1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

    21 09:34:23.186 13/04/11 Sev = Info/5 IKE/0x6300005E

    Customer address a request from firewall to hub

    22 09:34:23.186 13/04/11 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to 71.xx.xx.253

    23 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = 71.xx.xx.253

    24 09:34:23.248 13/04/11 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

    25 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 172.26.6.1

    26 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.0.0

    27 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 172.26.0.250

    28 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 172.26.0.251

    29 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000000

    30 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000E

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = TLCUSA

    31 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

    32 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000E

    MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc. ASA5505 Version 8.2 (1) built by manufacturers on Wednesday 5 May 09 22:45

    33 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

    34 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = received and by using the NAT - T port number, value = 0 x 00001194

    35 09:34:23.248 13/04/11 Sev = Info/4 CM / 0 x 63100019

    Data in mode Config received

    36 09:34:23.264 13/04/11 Sev = Info/4 IKE / 0 x 63000056

    Received a request from key driver: local IP = 172.26.6.1, GW IP = 71.xx.xx.253, Remote IP = 0.0.0.0

    37 09:34:23.264 13/04/11 Sev = Info/4 IKE / 0 x 63000013

    SEND to > QM ISAKMP OAK * (HASH, SA, NO, ID, ID) to 71.xx.xx.253

    38 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = 71.xx.xx.253

    39 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

    40 09:34:23.326 13/04/11 Sev = Info/5 IKE / 0 x 63000045

    Answering MACHINE-LIFE notify has value of 86400 seconds

    41 09:34:23.326 13/04/11 Sev = Info/5 IKE / 0 x 63000047

    This AA is already living from 0 seconds, setting the expiration to 86400 seconds right now

    42 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = 71.xx.xx.253

    43 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

    44 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO *(HASH, DEL) to 71.xx.xx.253

    45 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000049

    IPsec security association negotiation made scrapped, MsgID = 89EE7032

    46 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000017

    Marking of IKE SA delete (I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8) reason = DEL_REASON_IKE_NEG_FAILED

    47 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = 71.xx.xx.253

    48 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000058

    Received an ISAKMP for a SA message no assets, I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8

    49 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(dropped)="" from="">

    50 09:34:26.696 13/04/11 Sev = Info/4 IKE/0x6300004B

    IKE negotiation to throw HIS (I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8) reason = DEL_REASON_IKE_NEG_FAILED

    51 09:34:26.696 13/04/11 Sev = Info/4 CM / 0 x 63100012

    ITS phase 1 deleted before first Phase 2 SA is caused by "DEL_REASON_IKE_NEG_FAILED".  Crypto 0 Active IKE SA, 0 IKE SA authenticated user in the system

    52 09:34:26.696 13/04/11 Sev = Info/5 CM / 0 x 63100025

    Initializing CVPNDrv

    53 09:34:26.696 13/04/11 Sev = Info/6 CM / 0 x 63100046

    Set indicator established tunnel to register to 0.

    54 09:34:26.696 13/04/11 Sev = Info/4 IKE / 0 x 63000001

    Signal received IKE to complete the VPN connection

    ----------------------------------------------------------------------------------------

    ASA 5505 CONFIG

    : Saved

    :

    ASA Version 8.2 (1)

    !

    ciscoasa hostname

    domain masociete.com

    activate tdkuTUSh53d2MT6B encrypted password

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 172.26.0.252 255.255.0.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address 71.xx.xx.253 255.255.255.240

    !

    interface Ethernet0/0

    switchport access vlan 2

    Speed 100

    full duplex

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    clock timezone IS - 5

    clock to summer time EDT recurring

    DNS server-group DefaultDNS

    domain masociete.com

    access-list LIMU_Split_Tunnel_List note the network of the company behind the ASA

    Standard access list LIMU_Split_Tunnel_List allow 172.26.0.0 255.255.0.0

    outside_access_in list extended access permit icmp any one

    outside_access_in list extended access udp allowed any any eq 4500

    outside_access_in list extended access udp allowed any any eq isakmp

    outside_access_in list extended access permit tcp any host 71.xx.xxx.251 eq ftp

    outside_access_in list extended access permit tcp any host 71.xx.xxx.244 eq 3389

    inside_outbound_nat0_acl list of allowed ip extended access all 172.26.5.192 255.255.255.240

    inside_outbound_nat0_acl list of allowed ip extended access all 172.26.6.0 255.255.255.128

    pager lines 24

    Enable logging

    asdm of logging of information

    Outside 1500 MTU

    Within 1500 MTU

    local pool VPN_POOL 172.26.6.1 - 172.26.6.100 255.255.0.0 IP mask

    ICMP unreachable rate-limit 1 burst-size 1

    enable ASDM history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_outbound_nat0_acl

    NAT (inside) 1 0.0.0.0 0.0.0.0

    static (inside, outside) 71.xx.xxx.251 172.26.5.9 netmask 255.255.255.255

    static (inside, outside) 71.xx.xxx.244 172.26.0.136 netmask 255.255.255.255

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 71.xx.xxx.241 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    GANYMEDE + Protocol Ganymede + AAA-server

    RADIUS Protocol RADIUS AAA server

    Enable http server

    http 172.26.0.0 255.255.0.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5

    Crypto ipsec transform-set transit mode TRANS_ESP_3DES_MD5

    Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

    Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS_ESP_3DES_MD5

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map interface card crypto outside

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd outside auto_config

    !

    no basic threat threat detection

    no statistical access list - a threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal DefaultRAGroup group strategy

    attributes of Group Policy DefaultRAGroup

    value of server WINS 172.26.0.250 172.26.0.251

    value of 172.26.0.250 DNS server 172.26.0.251

    Protocol-tunnel-VPN IPSec l2tp ipsec svc

    value by default-field TLCUSA

    internal LIMUVPNPOL1 group policy

    LIMUVPNPOL1 group policy attributes

    value of 172.26.0.250 DNS server 172.26.0.251

    VPN-idle-timeout 30

    Protocol-tunnel-VPN IPSec l2tp ipsec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list LIMU_Split_Tunnel_List

    the address value VPN_POOL pools

    internal TLCVPNGROUP group policy

    TLCVPNGROUP group policy attributes

    value of 172.26.0.250 DNS server 172.26.0.251

    Protocol-tunnel-VPN IPSec l2tp ipsec svc

    Re-xauth disable

    enable IPSec-udp

    value by default-field TLCUSA

    barry.julien YCkQv7rLwCSNRqra06 + QXg password user name is nt encrypted privilege 0

    username barry.julien attributes

    VPN-group-policy TLCVPNGROUP

    Protocol-tunnel-VPN IPSec l2tp ipsec

    bjulien bhKBinDUWhYqGbP4 encrypted password username

    username bjulien attributes

    VPN-group-policy TLCVPNGROUP

    attributes global-tunnel-group DefaultRAGroup

    address VPN_POOL pool

    Group Policy - by default-DefaultRAGroup

    IPSec-attributes tunnel-group DefaultRAGroup

    pre-shared-key *.

    tunnel-group DefaultRAGroup ppp-attributes

    no authentication ms-chap-v1

    ms-chap-v2 authentication

    type tunnel-group TLCVPNGROUP remote access

    attributes global-tunnel-group TLCVPNGROUP

    address VPN_POOL pool

    Group Policy - by default-TLCVPNGROUP

    IPSec-attributes tunnel-group TLCVPNGROUP

    pre-shared-key *.

    ISAKMP ikev1-user authentication no

    tunnel-group TLCVPNGROUP ppp-attributes

    PAP Authentication

    ms-chap-v2 authentication

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:b94898c163c59cee6c143943ba87e8a4

    : end

    enable ASDM history

    can you try to change the transformation of dynamic value ESP-3DES-SHA map.

    for example

    remove the encryption scheme dynamic-map outside_dyn_map 20 transform-set TRANS_ESP_3DES_MD5

    and replace with

    Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  • Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

    Hello

    I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

    I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

    Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

    Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
    Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

    The router configuration

    IKE policy

    VPN strategy

    Client configuration

    Hôte : < router="" ip=""> >

    Authentication group name: remote.com

    Password authentication of the Group: mysecretpassword

    Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

    Username: myusername

    Password: mypassword

    Please contact Cisco.

    Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

    You can use the PPTP on the RV180 server to connect a PPTP Client.

    In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

  • Unable to connect using the Cisco VPN client

    Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

    I enclose the relevant configuration information in the attachment. Any help is welcome.

    Depending on the version, add...

    ISAKMP nat-traversal

    or

    ISAKMP nat-traversal crypto

    Should be all you need.

  • Is there really a customer Cisco VPN for Linux? _Really? _

    Hello people,

    I finally after almost a brain aneurysm trying to think too hard I have my Cisco 881 - SEC - K9 router configured properly for a multi-point my Amazon Virtual Private Cloud IPSec VPN tunnel, so that the obstacle is finally spent, and I think that it has been a very important step in my life somehow. I never thought I'd see the day, I actually got my hands on a legitimate Cisco non - stink... uh... I mean, non-linksys router. Now I can't find a "client" VPN for Linux program. I am running a Xen Hypervisor environment on openSUSE Linux because it is the only Linux distribution that fills all my laborious requirements in a Linux server environment. It is also the most mature and sure Linux on this planet, making it the most significant Linux distribution for my research needs.  Using NetworkManager is not really an option for a Linux based server environment and OpenVPN is just too complicated to understand for my little tiny head.  I've heard of some mysterious "easy VPN", but after that hours of digging online there is no information on this subject, even the Cisco download link leads to a Page not found error.  I see a Linux VPN API for the AnyConnect program, but is it a real VPN client, or just an API?  It seems to want my money to download it, but I have no money nor I really know what it is because it's all closed, the secret-like source and I can not even find a simple README file on him explaining what it is exactly.  I'm just a developer of off-work software attempts to connect to my home for personal use router and I can not really afford to more than $ 1 million for a single program I will only need to download once in my life that should have been included with the router in the first place of the fork. I have that more volunteer will probably not yet able to understand how to use the program when even because I don't know anything about VPN connections, that's why I bought this router so I can try to figure it all out as part of the open source nonprofit, research, I am currently conducting.  Is there some sort of period of evaluation or trial for personal use? Which would be really good if I could at least know if I will be able to understand or not.  I hate throwing money when it is in such a shortage these days. Is there really no alternative to a Cisco router.  It is an absolute necessity for the things I'm trying to accomplish, so try to settle for something else and past with my life isn't really an option. No, it's something that I just need to raise its head on and finish.

    I may be a little too crazy in me for my own good, but I don't see why it should take so much money just to learn to do something for personal use, it is not really a skill that I would never use otherwise.  Wouldn't be great if Cisco did their VPN client open-source and free for the public to use and modify, improve, learn and to grow and bring the whole world together in a community? Even the source code to the discontinuous old Cisco VPN client could be used as a tool for learning valuable for some poor student hungry or developer of Open Source software somewhere trying to cope with Sauce and Ramen noodles noodles Ramen on toast (don't tell me you've never thought about it).  With the ripple effect, it would significantly improve sales over time, because it would open the door to a whole new market where could those who previously could not afford to participate now. That's the real power of Open Source. It creates a more skilled workforce for the future by contributing openly and share knowledge. What happens if the next big internet technology and the solution to the global tyranny - the solution to end all wars forever - locked in the mind of a software developer to unemployment, which could not afford to upgrade their software to router from cisco or access the software they need because he was source closed and required engage in a costly to download service contract?  It would be just terrible, wouldn't it?  I guess there is no way to ever know for sure. I guess I'd be as happy if a kind soul out there could tell me an alternative easy to use for one always on the VPN connection that is running in the background that does not require NetworkManager or having to spend days days searching in and trying to figure out some really poor or extremely complex documents?  I apologize for all the sentences run on posed as a question, but just a few serious mental exhaustion of this, being unemployed is a few people from hard work. I really could use a vacation.  Maybe a camping on the coast trip is in order after I get this job, that sounds nice, isn't it? Nothing like a summer storm on the beach to the ocean--away from technology - to refresh the mind.

    I won't step in all the discussions in there, but you might want to look into is vpnc and openconnect.

    The two opensource projects that seem to work with devices Cisco, for a long time, I've been a user of vpnc.

    http://www.infradead.org/openconnect/

    http://www.UNIX-AG.uni-kl.de/~Massar/vpnc/

    Looks like some of your questions, concerns should be directed to your Cisco rep.

    There is an AC for Linux client (component the GUI and CLI). If you have problems finding - get it from 'package' (for linux) file, which is essentially a zip.

  • Customer Cisco VPN through PIX

    I have a PIX 501. I would use the Cisco VPN Client through the PIX to connect to a PIX on another site. The client will connect, but there is no traffic through the connection. What can I do?

    On the remote PEER PIX, add the following line.

    ISAKMP nat-traversal 20

    sincerely

    Patrick

  • Customer Cisco VPN not prompt to change the password when the Radius ID is due has expired.

    Hello, I would like to know what is behind a Cisco VPN client software to the user PC invites not to change the password when their password ID RADIUS is expiring/expired. I would also like to know what is the solution to work around him. Thanks in advance.

    Hello

    The "password management" command is configured?

    For the password function - expires to work in conjunction with the ray, that's all you need on the SAA.

    Let me know.

    Thank you.

  • Internet has stopped working when it is connected to the Cisco VPN

    Hello

    I configured IPSec (Ikev1) WHAT VPN remote access in ASA 5520, VPN connects correctly and I am able to access all internal resources but Internet does not work when connected to the VPN. I studied on it and found the problem with the default gateway, I'm ddefault duringVPN gateway connection. I'm surprised in ASA, there is no default gateway configured for the pool of IP VPN remote and remote clients then how can get a default gateway.

    I describe my problem below using image in shootout gave it.

    Thanks in advanve.

    Hi Mukesh,

    Until you specify command below according to your group policy, you will get the default gateway assigned by ASA to the user of your vpn. Please update your config strategy & group of tunnel

    Group XYZ policy attributes

    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value split tunnel

    tunnel of splitting allowed access list standard 172.16.1.0 255.255.255.0

    For anyconnect with split tunnel use below URL help

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080975e83.shtml

    ASA/PIX: Allow the tunneling split for the VPN Clients on the example of Configuration of ASA

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702999.shtml


    HTH

    Concerning
    Santhosh silou

  • This allows the customer Cisco VPN through PIX

    Hello. I seeks to allow the client VPN Cisco of LAN of the company to remote resources.

    It's put PAT in place on the PIX and I'll add the following lines to the ACL in the inside interface to allow access to the customer:

    permit tcp x.x.x.x y.y.y.y eq 50

    permit tcp x.x.x.x y.y.y.y eq 51

    permit udp x.x.x.x y.y.y.y eq 500

    permit udp x.x.x.x y.y.y.y eq 4500

    I have not done something like this before so I don't know if that will be enough to allow the connection of the client to remote resources.

    I have to do something else to make it work?

    That should be good for the local pix, but make sure that nat-traversal is enabled on the remote device.

    ESP and ah protocols, not ports. 50 and 51.

    esp x.x.x.x y.y.y.y permit

    allowed ah x.x.x.x y.y.y.y

    permit udp x.x.x.x y.y.y.y eq 500

    permit udp x.x.x.x y.y.y.y eq 4500

  • WRT1200AC/1900AC WIRED Intermittent connectivity software company (Cisco) VPN - resolved

    I work from a Home Office 24 x 7 as a software engineer supporting the business intelligence world production for a credit/bank card issuer applications - so my 'stuff' has to work.  My components materials network and the machines are "top-shelf."  I recently added a WRT1900AC router and have started to feel the intermittent connectivity WIRED to VPN my company (Cisco AnyConnect Secure Mobility Client).  To be clear, this has nothing to do with the setting of the OpenVPN server is available via the user interface of the Linksys Smart Wi - Fi.  In any case, after many hours of research and changes the configuration on the router (with a significant amount of curse and aggravation), I solved the problem by using the areas of prioritization of media and bandwidth downstream from the HMI.  Question a also experienced, but to a lesser extent, during the wireless connection.  It was confusing, since generally the when router problems occur, they seem to be more related to the Wi - Fi connection rather than wired.  Anyway, I wanted to share this info with other poor souls that might have been ostrasized of their family, friends and colleagues as a result of this almost apocalyptic puzzle.

    You are welcome. Happy holidays! Certainly happy to clarify as needed.

  • RDP connection client for Cisco VPN Windows machine

    Hello

    I am a linux user and because the cisco client is not available for Linux (Kernel 2.6.34 >) my company has installed a machine VMWare Windows7 so I can install the VPN client of our client of my company. For sure, I don't want to use the Windows machine via the vmware client, so I use through a RDP connection.

    Unfortunately, if I set up the VPN, the RDP connection degrades. This seems to be quite common for VPN clients however, it seems to be configurable somehow. I already tried to change the routing table, but it doesn't seem to be a problem with routing. The customer puts a firewall or something like that?

    Thank you

    Kim Neunert

    It really depends on how the VPN server is configured? If it's the tunnel to the VPN server, or it has split the configured tunnel.

    If it is indeed tunnel all to the VPN server, it will certainly break the local RDP session.

Maybe you are looking for

  • Is there an analytical test for the wireless?

    Does anyone know of an analytical test hardware wireless for a MacBook Pro?  I'm having persistent problems with a periodic loss of binding and were able to verify that the router is not the problem, so I need to look at the MB Pro.

  • GF fubar'ed its rocket!

    My FRIEND called me crying cause she couldn't listen to his MP3 player on her evening walk... and then, she said, "he said: [quote] Not enough free space for music DB Please free 90 MB [/ quote] I finally had the time to have a look today, and he use

  • How to map a drive on my computer?

    try to map a drive from x to my computer. What do I need to do?

  • How to create the gallery video lightbox

    I'm trying to get a video gallery lightbox, but what selection videos are grayed out and cannot be selected. what I am doing wrong?

  • Installation of Design Premium: Acrobat won't install

    Everything is outside Acrobat, eveny time I try keep coming with the error message: Exit Code 7?Any ideas?