Customer Cisco VPN through PIX

I have a PIX 501. I would use the Cisco VPN Client through the PIX to connect to a PIX on another site. The client will connect, but there is no traffic through the connection. What can I do?

On the remote PEER PIX, add the following line.

ISAKMP nat-traversal 20

sincerely

Patrick

Tags: Cisco Security

Similar Questions

This allows the customer Cisco VPN through PIX

Hello. I seeks to allow the client VPN Cisco of LAN of the company to remote resources.

It's put PAT in place on the PIX and I'll add the following lines to the ACL in the inside interface to allow access to the customer:

permit tcp x.x.x.x y.y.y.y eq 50

permit tcp x.x.x.x y.y.y.y eq 51

permit udp x.x.x.x y.y.y.y eq 500

permit udp x.x.x.x y.y.y.y eq 4500

I have not done something like this before so I don't know if that will be enough to allow the connection of the client to remote resources.

I have to do something else to make it work?

That should be good for the local pix, but make sure that nat-traversal is enabled on the remote device.

ESP and ah protocols, not ports. 50 and 51.

esp x.x.x.x y.y.y.y permit

allowed ah x.x.x.x y.y.y.y

permit udp x.x.x.x y.y.y.y eq 500

permit udp x.x.x.x y.y.y.y eq 4500

Cisco VPN client, PIX, and proxy

Hi.I have problem in my company. We have users that go through a proxy server located in the DMZ of a PIX to the internet (allowed through the ACL of the DMZ on the outside, etc.). Which works very well.

The problem arises when they use a Cisco VPN client to connect to another company, and they can no longer access the Internet, but may work via VPN to a remote site (client has been authorized by the Cisco PIX). Everything returns to normal when they no longer use the VPN client.

Any ideas why this would happen?

Without the proxy, browsing the internet via the vpn connection, or split tunnel is configured and you are leaving locally. If split tunnel is configured, the ip address of proxy server can overlap with the remote protected network.

Fortunately, it is easy for you to know how the vpn is configured, just check the route details of vpn client statistics tab.

Verify that the routing table local pc will also help you to solve this problem.

Error of customer Cisco VPN connection ASA 5505

I am unable to connect to the vpn I created on my ASA 5505 using the Cisco VPN Client on a Windows machine. The log of the vpn client and the config of the ASA 5505 is lower. Any help to solve this is appreciated.

CISCO VPN CLIENT LOG

Cisco Systems VPN Client Version 5.0.06.0160

Copyright (C) 1998-2009 Cisco Systems, Inc.. All rights reserved.

Customer type: Windows, Windows NT

Running: 6.1.7600

Config files directory: C:\Program Cisco Systems Client\

1 09:34:23.030 13/04/11 Sev = Info/4 CM / 0 x 63100002

Start the login process

2 09:34:23.061 13/04/11 Sev = Info/4 CM / 0 x 63100004

Establish a secure connection

3 09:34:23.061 13/04/11 Sev = Info/4 CM / 0 x 63100024

Attempt to connect with the server "71.xx.xx.253".

4 09:34:23.061 13/04/11 Sev = Info/6 IKE/0x6300003B

Attempts to establish a connection with 71.xx.xx.253.

5 09:34:23.061 13/04/11 Sev = Info/4 IKE / 0 x 63000001

From IKE Phase 1 negotiation

6 09:34:23.077 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 71.xx.xx.253

7 09:34:23.170 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

8 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

9 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer is a compatible peer Cisco-Unity

10 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports XAUTH

11 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports the DPD

12 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports NAT - T

13 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports fragmentation IKE payloads

14 09:34:23.170 13/04/11 Sev = Info/6 IKE / 0 x 63000001

IOS Vendor ID successful construction

15 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) at 71.xx.xx.253

16 09:34:23.170 13/04/11 Sev = Info/6 IKE / 0 x 63000055

Sent a keepalive on the IPSec Security Association

17 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000083

IKE port in use - Local Port = 0xEB07, Remote Port = 0 x 1194

18 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000072

Automatic NAT detection status:

Remote endpoint is NOT behind a NAT device

This effect is behind a NAT device

19 09:34:23.170 13/04/11 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

20 09:34:23.170 13/04/11 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

21 09:34:23.186 13/04/11 Sev = Info/5 IKE/0x6300005E

Customer address a request from firewall to hub

22 09:34:23.186 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to 71.xx.xx.253

23 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

24 09:34:23.248 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

25 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 172.26.6.1

26 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.0.0

27 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 172.26.0.250

28 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 172.26.0.251

29 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000000

30 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = TLCUSA

31 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

32 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc. ASA5505 Version 8.2 (1) built by manufacturers on Wednesday 5 May 09 22:45

33 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

34 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = received and by using the NAT - T port number, value = 0 x 00001194

35 09:34:23.248 13/04/11 Sev = Info/4 CM / 0 x 63100019

Data in mode Config received

36 09:34:23.264 13/04/11 Sev = Info/4 IKE / 0 x 63000056

Received a request from key driver: local IP = 172.26.6.1, GW IP = 71.xx.xx.253, Remote IP = 0.0.0.0

37 09:34:23.264 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > QM ISAKMP OAK * (HASH, SA, NO, ID, ID) to 71.xx.xx.253

38 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

39 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

40 09:34:23.326 13/04/11 Sev = Info/5 IKE / 0 x 63000045

Answering MACHINE-LIFE notify has value of 86400 seconds

41 09:34:23.326 13/04/11 Sev = Info/5 IKE / 0 x 63000047

This AA is already living from 0 seconds, setting the expiration to 86400 seconds right now

42 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

43 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

44 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK INFO *(HASH, DEL) to 71.xx.xx.253

45 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000049

IPsec security association negotiation made scrapped, MsgID = 89EE7032

46 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000017

Marking of IKE SA delete (I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8) reason = DEL_REASON_IKE_NEG_FAILED

47 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

48 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000058

Received an ISAKMP for a SA message no assets, I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8

49 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(dropped)="" from="">

50 09:34:26.696 13/04/11 Sev = Info/4 IKE/0x6300004B

IKE negotiation to throw HIS (I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8) reason = DEL_REASON_IKE_NEG_FAILED

51 09:34:26.696 13/04/11 Sev = Info/4 CM / 0 x 63100012

ITS phase 1 deleted before first Phase 2 SA is caused by "DEL_REASON_IKE_NEG_FAILED". Crypto 0 Active IKE SA, 0 IKE SA authenticated user in the system

52 09:34:26.696 13/04/11 Sev = Info/5 CM / 0 x 63100025

Initializing CVPNDrv

53 09:34:26.696 13/04/11 Sev = Info/6 CM / 0 x 63100046

Set indicator established tunnel to register to 0.

54 09:34:26.696 13/04/11 Sev = Info/4 IKE / 0 x 63000001

Signal received IKE to complete the VPN connection

----------------------------------------------------------------------------------------

ASA 5505 CONFIG

: Saved

:

ASA Version 8.2 (1)

!

ciscoasa hostname

domain masociete.com

activate tdkuTUSh53d2MT6B encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

names of

!

interface Vlan1

nameif inside

security-level 100

IP 172.26.0.252 255.255.0.0

!

interface Vlan2

nameif outside

security-level 0

IP address 71.xx.xx.253 255.255.255.240

!

interface Ethernet0/0

switchport access vlan 2

Speed 100

full duplex

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

passive FTP mode

clock timezone IS - 5

clock to summer time EDT recurring

DNS server-group DefaultDNS

domain masociete.com

access-list LIMU_Split_Tunnel_List note the network of the company behind the ASA

Standard access list LIMU_Split_Tunnel_List allow 172.26.0.0 255.255.0.0

outside_access_in list extended access permit icmp any one

outside_access_in list extended access udp allowed any any eq 4500

outside_access_in list extended access udp allowed any any eq isakmp

outside_access_in list extended access permit tcp any host 71.xx.xxx.251 eq ftp

outside_access_in list extended access permit tcp any host 71.xx.xxx.244 eq 3389

inside_outbound_nat0_acl list of allowed ip extended access all 172.26.5.192 255.255.255.240

inside_outbound_nat0_acl list of allowed ip extended access all 172.26.6.0 255.255.255.128

pager lines 24

Enable logging

asdm of logging of information

Outside 1500 MTU

Within 1500 MTU

local pool VPN_POOL 172.26.6.1 - 172.26.6.100 255.255.0.0 IP mask

ICMP unreachable rate-limit 1 burst-size 1

enable ASDM history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_outbound_nat0_acl

NAT (inside) 1 0.0.0.0 0.0.0.0

static (inside, outside) 71.xx.xxx.251 172.26.5.9 netmask 255.255.255.255

static (inside, outside) 71.xx.xxx.244 172.26.0.136 netmask 255.255.255.255

Access-group outside_access_in in interface outside

Route outside 0.0.0.0 0.0.0.0 71.xx.xxx.241 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

GANYMEDE + Protocol Ganymede + AAA-server

RADIUS Protocol RADIUS AAA server

Enable http server

http 172.26.0.0 255.255.0.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_MD5

Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS_ESP_3DES_MD5

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

crypto ISAKMP policy 30

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH timeout 5

Console timeout 0

dhcpd outside auto_config

!

no basic threat threat detection

no statistical access list - a threat detection

no statistical threat detection tcp-interception

WebVPN

internal DefaultRAGroup group strategy

attributes of Group Policy DefaultRAGroup

value of server WINS 172.26.0.250 172.26.0.251

value of 172.26.0.250 DNS server 172.26.0.251

Protocol-tunnel-VPN IPSec l2tp ipsec svc

value by default-field TLCUSA

internal LIMUVPNPOL1 group policy

LIMUVPNPOL1 group policy attributes

value of 172.26.0.250 DNS server 172.26.0.251

VPN-idle-timeout 30

Protocol-tunnel-VPN IPSec l2tp ipsec

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list LIMU_Split_Tunnel_List

the address value VPN_POOL pools

internal TLCVPNGROUP group policy

TLCVPNGROUP group policy attributes

value of 172.26.0.250 DNS server 172.26.0.251

Protocol-tunnel-VPN IPSec l2tp ipsec svc

Re-xauth disable

enable IPSec-udp

value by default-field TLCUSA

barry.julien YCkQv7rLwCSNRqra06 + QXg password user name is nt encrypted privilege 0

username barry.julien attributes

VPN-group-policy TLCVPNGROUP

Protocol-tunnel-VPN IPSec l2tp ipsec

bjulien bhKBinDUWhYqGbP4 encrypted password username

username bjulien attributes

VPN-group-policy TLCVPNGROUP

attributes global-tunnel-group DefaultRAGroup

address VPN_POOL pool

Group Policy - by default-DefaultRAGroup

IPSec-attributes tunnel-group DefaultRAGroup

pre-shared-key *.

tunnel-group DefaultRAGroup ppp-attributes

no authentication ms-chap-v1

ms-chap-v2 authentication

type tunnel-group TLCVPNGROUP remote access

attributes global-tunnel-group TLCVPNGROUP

address VPN_POOL pool

Group Policy - by default-TLCVPNGROUP

IPSec-attributes tunnel-group TLCVPNGROUP

pre-shared-key *.

ISAKMP ikev1-user authentication no

tunnel-group TLCVPNGROUP ppp-attributes

PAP Authentication

ms-chap-v2 authentication

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

!

global service-policy global_policy

context of prompt hostname

Cryptochecksum:b94898c163c59cee6c143943ba87e8a4

: end

enable ASDM history

can you try to change the transformation of dynamic value ESP-3DES-SHA map.

for example

remove the encryption scheme dynamic-map outside_dyn_map 20 transform-set TRANS_ESP_3DES_MD5

and replace with

Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

Connection of customer Cisco VPN to work

I recently picked up 1 billion domestic 7800N router to replace my old netgear which fell signal much.

I seem to have some access to my work via VPN client network problem. I can't connect the Cisco VPN client to the network ok but I have no access to the email server and exchange. I tested the parameters of the client on my old Netgear and it works fine. That tells me that the management of the router...

I don't have any packet filtering on and I put in place profile of my fixed ip of internal House on the ip of the work to allow any protocol and any port.

I also sent port 500, 4500 and internal 10000UDP to my ip address.

I'm a noob when it comes to networking and I'm a little lost. I feel this topic falls in the middle ground between the client and the seup router if I appreciate draw my having a definitive answer. I can post a copy of the customer logs if this is useful.

I hope someone can point me in the right direction...

Thank you

Neil

Hello

It looks like your home network is using the same ip as your work network range. I recommend you to choose a new range for your home network that is not identified in the routing table updates in your newspapers.

For example: 10.255.255.0/24

Best regards

Ju

Sent by Cisco Support technique iPad App

Is there really a customer Cisco VPN for Linux? _Really? _

Hello people,

I finally after almost a brain aneurysm trying to think too hard I have my Cisco 881 - SEC - K9 router configured properly for a multi-point my Amazon Virtual Private Cloud IPSec VPN tunnel, so that the obstacle is finally spent, and I think that it has been a very important step in my life somehow. I never thought I'd see the day, I actually got my hands on a legitimate Cisco non - stink... uh... I mean, non-linksys router. Now I can't find a "client" VPN for Linux program. I am running a Xen Hypervisor environment on openSUSE Linux because it is the only Linux distribution that fills all my laborious requirements in a Linux server environment. It is also the most mature and sure Linux on this planet, making it the most significant Linux distribution for my research needs. Using NetworkManager is not really an option for a Linux based server environment and OpenVPN is just too complicated to understand for my little tiny head. I've heard of some mysterious "easy VPN", but after that hours of digging online there is no information on this subject, even the Cisco download link leads to a Page not found error. I see a Linux VPN API for the AnyConnect program, but is it a real VPN client, or just an API? It seems to want my money to download it, but I have no money nor I really know what it is because it's all closed, the secret-like source and I can not even find a simple README file on him explaining what it is exactly. I'm just a developer of off-work software attempts to connect to my home for personal use router and I can not really afford to more than $ 1 million for a single program I will only need to download once in my life that should have been included with the router in the first place of the fork. I have that more volunteer will probably not yet able to understand how to use the program when even because I don't know anything about VPN connections, that's why I bought this router so I can try to figure it all out as part of the open source nonprofit, research, I am currently conducting. Is there some sort of period of evaluation or trial for personal use? Which would be really good if I could at least know if I will be able to understand or not. I hate throwing money when it is in such a shortage these days. Is there really no alternative to a Cisco router. It is an absolute necessity for the things I'm trying to accomplish, so try to settle for something else and past with my life isn't really an option. No, it's something that I just need to raise its head on and finish.

I may be a little too crazy in me for my own good, but I don't see why it should take so much money just to learn to do something for personal use, it is not really a skill that I would never use otherwise. Wouldn't be great if Cisco did their VPN client open-source and free for the public to use and modify, improve, learn and to grow and bring the whole world together in a community? Even the source code to the discontinuous old Cisco VPN client could be used as a tool for learning valuable for some poor student hungry or developer of Open Source software somewhere trying to cope with Sauce and Ramen noodles noodles Ramen on toast (don't tell me you've never thought about it). With the ripple effect, it would significantly improve sales over time, because it would open the door to a whole new market where could those who previously could not afford to participate now. That's the real power of Open Source. It creates a more skilled workforce for the future by contributing openly and share knowledge. What happens if the next big internet technology and the solution to the global tyranny - the solution to end all wars forever - locked in the mind of a software developer to unemployment, which could not afford to upgrade their software to router from cisco or access the software they need because he was source closed and required engage in a costly to download service contract? It would be just terrible, wouldn't it? I guess there is no way to ever know for sure. I guess I'd be as happy if a kind soul out there could tell me an alternative easy to use for one always on the VPN connection that is running in the background that does not require NetworkManager or having to spend days days searching in and trying to figure out some really poor or extremely complex documents? I apologize for all the sentences run on posed as a question, but just a few serious mental exhaustion of this, being unemployed is a few people from hard work. I really could use a vacation. Maybe a camping on the coast trip is in order after I get this job, that sounds nice, isn't it? Nothing like a summer storm on the beach to the ocean--away from technology - to refresh the mind.

I won't step in all the discussions in there, but you might want to look into is vpnc and openconnect.

The two opensource projects that seem to work with devices Cisco, for a long time, I've been a user of vpnc.

http://www.infradead.org/openconnect/

http://www.UNIX-AG.uni-kl.de/~Massar/vpnc/

Looks like some of your questions, concerns should be directed to your Cisco rep.

There is an AC for Linux client (component the GUI and CLI). If you have problems finding - get it from 'package' (for linux) file, which is essentially a zip.

Help: Customer Cisco VPN & Split Tunnel but not Internet

Hi Forum.

We are faced with this problem: after having successfully open a VPN connection with the Cisco VPN Client to a router Cisco, the rest of the world are not properly available more.

This is what has been verified / so far attempted to identify the problem on a Windows Vista computer:

-Router: Split Tunneling is allowed according to sysop

-On the VPN-Client: "allow Local Lan access" is checked

-On the Client (statistics): only STI VPN-rout configured listed unter "guarantee routes." "Local Lan routes" is empty.

-Calling 'http://www.google.com' in IE fails

-Call ' 74.125.232.116' (IE IP) IE works / ping the IP works.

-nslookup properly lists the current DNS server

-nslookup www.google.com resolves correctly the name of intellectual property

It seems that it is not that the connection with the rest of the Internet is deleted, but DNS resolution fails somehow, even though all signs point to the appropriate DNS server is in force and although the command line can resolve the name.

does anyone have a tip how to debug this correctly?

No worries Pat...

Sent by Cisco Support technique iPhone App

-Please evaluate solutions

Customer Cisco VPN not prompt to change the password when the Radius ID is due has expired.

Hello, I would like to know what is behind a Cisco VPN client software to the user PC invites not to change the password when their password ID RADIUS is expiring/expired. I would also like to know what is the solution to work around him. Thanks in advance.

Hello

The "password management" command is configured?

For the password function - expires to work in conjunction with the ray, that's all you need on the SAA.

Let me know.

Thank you.

Unable to connect to the Cisco VPN you use native client: El Capitan

I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."

When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:

* connect using the old work VPN connection: without success

Config: Hand [server address, account name],

AUTH settings [shared secret, the Group name].

Advanced [mode to use the passive FTP = TRUE]

errors:

"authd [124]: copy_rights: _server_authorize failed.

"raccoon [2580]: could not send message vpn_control: Broken pipe"

...

* Add new VPN connection using L2TP over IPSec: without success

Config: Hand [server address, account name],

Authentication settings [user authentication: password, identification of the Machine: Shared Secret].

Advanced [send all traffic on the VPN = TRUE]

errsors:

"pppd [2616]: password not found in the system keychain.

"authd [124]: copy_rights: _server_authorize failed.

...

* Add new connection using Cisco via IPSec VPN: without success

Main config: [server address, account name].

AUTH settings [shared secret, the Group name].

Advanced [mode to use the passive FTP = TRUE]

errors:

"authd [124]: copy_rights: _server_authorize failed.

"raccoon [2580]: could not send message vpn_control: Broken pipe"

VPN server is high and does not work and accepts connections, this problem is entirely on the client side.

I. Journal of Console app existing/Legacy VPN connection:

26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics

26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]

26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status

26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.

26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 339 [2580]: connection.

26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.

26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 405 [2580]: connection.

26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.

[26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting

26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).

26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

[26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no

26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

$VPN_SERVER_IP

II. new VPN connection using L2TP over IPSec Console app log:

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856

26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856

26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13

26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent

26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]

26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status

26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory

26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]

26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller

26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller

26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.

26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.

26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain

26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!

26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!

26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501

26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback

26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback

26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed

26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify

III. New connection of Cisco VPN through IPSec Console app log:

26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]

[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status

26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.

26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed

26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:19:56, racoon 296 [2576]: connection.

26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.

26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

26/03/16 10:19:56, 374 raccoon [2576]: connection.

26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.

[26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting

26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).

26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

[26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no

26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

It seems that I solved the problem, but I'm not sure it helped.

After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.

Cisco VPN Client behind PIX 515E,-> VPN concentrator

I'm trying to configure a client as follows:

The user is running Cisco VPN Client 4.0. They are behind a 6.1 PIX 515E (4), and I need to connect to a VPN concentrator located outside of our network. We use PAT for address translation. As far as I know, to allow ipsec through Firewall 1 tunnel, I need to upgrade the pix to 6.3 and activate "fixup protocol esp-ike.

Is there another way to do this? I am also curious to know how much more easy/better this will work if we were dealing with pptp.

You don't necessarily need to fixup protocol esp-ike active. The remote Hub there encapsulation NAT - T enabled so that clients behind the NAT can run?

PIX: Cisco VPN Client connects but no routing

Hello

We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

I enclose the training concerned in order to understand the problem:

interface Ethernet0

Speed 100

full duplex

nameif outside

security-level 0

IP address xx.yy.zz.tt 255.255.255.240

!

interface Ethernet1

nameif inside

security-level 100

172.16.0.1 IP address 255.255.255.0

!

access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

!

access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

!

VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

!

IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

!

NAT-control

Global xx.yy.zz.tt 12 (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 12 172.16.0.12 255.255.255.255

!

internal VPN_clientes group strategy

attributes of Group Policy VPN_clientes

xxyyzz.NET value by default-field

internal VPN_client_group group strategy

attributes of Group Policy VPN_client_group

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

xxyyzz.local value by default-field

!

I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

Thank you very much.

can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

PIX / ASA 7.1 and earlier versions

PIX (config) #isakmp nat-traversal 20

PIX / ASA 7.2 (1) and later versions

PIX (config) #crypto isakmp nat-traversal 20

Cisco ASA5520 facing ISP with private IP address. How to get the IPSec VPN through the internet?

/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

Hello guys,.

I have Cisco ASA5520 facing the ISP with private IP address. We don't have a router and how to get the IPSec VPN through the internet?

The question statement not the interface pointing to ISP isn't IP address private and inside as well.

Firewall configuration:

Firewall outside interface Gi0 10.0.1.2 > ISP 10.0.1.1 with security-level 0

Firewall inside the interface Ethernet0 192.168.1.1 > LAN switch 192.168.1.2 with security-level 100

I have public IP block 199.9.9.1/28

How can I use the public IP address to create the IPSec VPN tunnel between two sites across the internet?

can I assign a public IP address on the Gig1 inside the interface with the security level of 100 and how to apply inside to carry on this interface?

If I configure > firewall inside of the item in gi1 interface ip address 199.9.9.1/28 with security-level 100. How to make a safe lane VPN through this interface on the internet?

I'm used to the public IP address allocation to the interface outside of the firewall and private inside the interface IP address.

Please help with configuration examples and advise.

Thank you

Eric

Unfortunately, you can only complete the VPN connection on the interface the VPN connection source, in your case the external interface.

3 options:

(1) connect a router in front of the ASA and assign your public ip address to the ASA outside interface.

OR /.

(2) If your ISP can perform static translation of 1 to 1, then you can always finish the VPN on the external interface and ask your provider what is the static ip address assigned to your ASA out of the IP (10.0.1.2) - this will launch the VPN of bidirectionally

OR /.

(3) If your ISP performs PAT (dynamic NAT), then you can only start the tunnel VPN on the side of the ASA and the other end of the tunnel must be configured to allow VPN LAN-to-LAN dynamics.

Cisco VPN Client anything cannot access through VPN on an ASA5505 8.4

Hello

Completely new to Cisco ASA and the need to get this working ASAP.

8.4 (1) ASA 5505 is the secondary FW and I need to authorize all out and block everything coming, but for the VPN clients. Since a jerk of Cisco, I used the ASDM and it's sorcerers to make this work, which may explain my situation.

192.168.101.0/24 is the local network

192.168.101.5 is the IP of ASA

192.168.101.2 is the primary FW (and the default gateway for servers, I have to access through the VPN)

10.10.101.0/24 is the VPN IP range (this can be what you want, I'm not married to it somehow)

My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x or service server (tried RDP, telnet, ping, etc.)

Configuration file is attached.

Help pretty please!

Thank you.

Did you add a route for the VPN Pool on the main firewall to the ASA?

Best regards

Peer

Sent by Cisco Support technique iPad App

Allow Cisco VPN Client through the firewall?

Hello

How can I allow a cisco VPN client work from the inside of our network to an external IP address?

We have customers who wish to make use of their Cisco VPN Client companies but our ASA blocks I think?

Also (sorry to ask) a friend in South America is having the same problem but I am not hink they use Cisco, is there a default port used by the client to Cisco? then I can send this info?

Thank you

Generally, the ASA will allow the IPSEC from the inside to outside traffic. This is when you want it came outside and connect to you - this is where it gets creative. You restrict outgoing traffic at all? You deny all ip/tcp/udp outgoing?

But may depend on if the remote end is compaitable NAT - T, and if they have configured. Another question would be how they allow VPN traffic go?

Cisco VPN + Win XP SP2 Firewall

We started to test Windows XP SP2, last week and met with an interesting question. If you activate the XP SP2 Firewall services it will disrupt Cisco VPN to establish a TCP connection. I created an exception to the application, but is not solving the problems.

Note: If you change the UDP/10000 connection it works fine, but IPSec through NAT on TCP/443 will not work.

Using "capture" on my PIX I can compare a successful connection (firewall off) and a failed connection (firewall). On the attempt of the ACK packet between the host and the VPN concentrator is blocked. Unfortunately the debugging of winXP is essentially useless.

Has anyone meet a similar problem? Any help would be appreciated.

Create an exception in the Windows Firewall to allow the 62515/udp port. The scope should be of any computer. It is my understanding that Cisco is working on an updated version of the client which will address this, but it should work in the meantime.

Customer Cisco VPN through PIX

Similar Questions

Maybe you are looking for