Construction 9333 XPS with USB ethernet problem

Similar Questions

• Sony Ericsson W595 USB Ethernet problem...

  I have a Sony Ericsson W595. There is an option in the phone which allows me to use the PC internet on the phone. However, when I use the USB Ethernet mode, can't do internet on the phone. In Network Center, it says 'Public unidentified network'. Using Network Diagnostics, it tells to restart the phone. Even after reboot, I get no Net. Diagnosis shows that "' ' Sony Ericsson HSPA 3.6Mbps ' is not a valid ip configuration". " PLEASE HELP ME!

  Hi Su Haris,

  The question you posted would be better suited in the Sony Ericsson Support. I would recommend posting your query in the Sony Ericsson Support Forums.

   

  Sony Ericsson Support

  http://www.sonymobile.com/us/support/phones/W595/

  Hope this information helps.

• Re: Play Peek-a-Boo with USB - driver problem

  Hello

  So far, I had no problem with my laptop and windows 7 (32 bit), but there was a problem from the start. my system was not able to detect all the drivers, for the moment, I got 2 unidentified "base system devices.

  At least one of them has got to do something with my USBs, when I connect a plug & play carpet dance for my laptop, it plays basically peek-a-boo with me - recognize something was plugged, but without realizing realize that he is.

  One of my friends even phone sex and BONE, he had no such problems.

  When I try to install the utility driver Support page, suitable for my 'edition', it will stop saying that I have not the common module installed on my system.

  Any help possible? As said, some drivers are missing, which are supposed to make my USB hubs identify devices again, but I know who exactly do not exist, or where to get them.

  Thank you for every little trick

  Great! Thanks for letting us share this last info

• OfficeJet Pro 8600 Plus: scans with USB, Ethernet 10 Mbit/s but with 1 Gbps

  I installed my router a Netgear router from 100 Mbps to 1 Gbps router TP LINK Archer C8. I use a printer more Officejet Pro 8600 with scanner. Scanned the fin on the Netgear router, it is not scan with TP link sanner. I get an error "Scanner communication cannot be established. I changed to a USB connection and was able to scan successfully. I noticed the printer only has 10 and 100 a half and full speed duplex settings. The scanner is not compatible with a 1 Gbps puts? I uninstalled and reinstalled several times printing software.

  UPDATE : tried the HP Scan and Capture application in the Windows store. Works very well. Must be some type of problem with the native drivers scan and connections broadband.

• PS3 connected to Windows 7 on laptop with usb ethernet and converter cable. Technician COMPUTER put in place, but the second time I used it it gave me the DNS 80710102 error

  I don't know that it's a quick fix that I'm used to the Macs. Someone please advise

  Hello

  Did recent changes to the computer?

  Follow these steps.

  1 - Open a browser and enter the router's IP address in the navigation bar. For most routers, the default IP address is (192.168.1.1).

  2 - Enter the user name and password to access the router. Press 'OK' and the console application will be displayed in the browser window.

  Tab 3 - Click the "Password". The UPnP settings are located in the same window as the password of the router settings.

  4. Select 'Disable' titled "UPnP" area and click on the Save"" button. Close the console of the router. Start the Playstation machine and connect to the Internet.

  For more information.

  http://community.EU.PlayStation.com/T5/PlayStation-Network-General/unofficial-DNS-error-fix-80710102/TD-p/7903885

  I hope this helps.

• Tecra S5 - slow ethernet with USB 2.0 Port Replicator

  Hello

  I have a Tecra S5 with USB 2.0 Port replicator II. I have 3 ethernet connections all together on my PC: LAN on motherboard, WiFi and the other on the USB port replicator.

  At home, I use WiFi for internet connection and USB to Ethernet to a wired connection to devices with built-in web server.

  My problem is that when the WiFi and USB to Etherenet is active the internet and the connection to the web server works but vey slow.
  If I turn off the WiFi and connect to the web server works properly.
  If I disable USB for Ethernet internet connection works correctly.

  Anyone has same problem and suggestion how to solve?
  I downloaded the latest drivers from the Toshiba support page.
  My OS is XPSP2.

  Concerning
  jballa

  Hello!

  It looks like a network configuration problem. Check the network addresses and configuration in command line with the command ipconfig/all.

  Try using static IP addresses. I think that the DHCP server takes a long time to go send an IP address to each laptop.

  Good bye

• WRT160NL connection with n and USB connection problem

  Hi guys,.

  I have the Linksys WRT160NL router and I have two fundamental problems with that:

  1. I have a laptop HP with n on its wireless card connection. (it's an HP probook 4720 s). So I know that this laptop has ability. n I have the most recent driver vor he 3.1.18. The thing is that my Linksys router does not transmit sound wireless n, just g...

  What should I do to make it work with n as well?

  2. the second issue is that the USB connection is working in a very strange way. I have attached an ADATA with USB 3.0 HDD external, even. He works in 2.0.

  I have a lot of WAV files on it and when I stream to my receiver files pay with much intrerupptions, break ups. MP3 work very well.

  I don't know what to do to solve this 2 problems... Maybe someone could help me...

  Thank you

  Try changing some settings on the router wireless.

  Connect the computer to the router with the Ethernet cable. Open the router configuration page. Go to the wireless tab and the manual value configuration view. Change the channel to 11 wireless. Make sure that the network is set to mixed. Save the settings.

  Go to wireless security sub tab and change the wireless WPA2 with AES security mode. Save the settings.

  Click the tab under advanced wireless settings change the tag to 75 interval, RTS threshold and fragmentation to 2304. Save the settings. Now try to connect to the network again.

• XPS 8500 USB 3.0 Port forward problems

  Ports USB 3.0 on the XPS 8500 give me bad, and from what I can tell, it comes from a physical problem with the port hardware.

  I can acquire and maintain a 3.0 connection when I plug my WD Passport drive or a Rocketfish hub propelled into the ports on the back. Connected to the front, however, I can sometimes 3.0, sometimes only 2.0 and rarely even get no connection at all. Connection I get to the front, if I move to sentence (like touch), the cable or the plug connection can change back from 2.0 to 3.0. Writing on a drive that will prevent mobile 3.0 to the front.

  I noticed that the physical connection of USB plug on the port is more solid at the back than the front. A cable plugged into the rear port 3.0 is able to travel further and the rubber around the contacts of plug of cable on the back of the computer. On the front ports, the connector does not travel in too far, and the rubber of the USB connector is about 1-2 mm of front cover of the computer. A 3.0 cable on the front can move much more than a through the rear hole. I should mention that I have no problem with the USB 2.0 cables or devices in these front ports.

  This isn't a driver problem, it is a problem of the plug 3.0 doesn't not not solid contact in the port. Dell must cease to use the current material in front port and to find a more appropriate part. Then, they can replace all the front ports on the XPS already shipped 8500.

  My problem with USB 3.0 before XPS 8500 ports seems to have been resolved by the new cables. However, my initial assessment of ports before being too loose, making it difficult to get good 3.0 connections still holds upward. To save their customers and themselves from many headaches, Dell needs to find a replacement part for these ports before issues.

  Everything that I had to test this with a WD Passport 3.0 years was HARD and a new Rocketfish powered 3.0 disc hub. Using the cables of original, these devices connected to ports at the back, but not the front. If I held the plug and stuck firmly in a front port, I couldn't sometimes 3.0 connection - although as soon as I let go of the plug I would lose the connection 3.0 and it would immediately reconnect as a 2.0 device.

  I bought a 3.0 a mini-B cable for direct use with the WD drive and a 3.0 extension cable A-male to female for general use. These cables make very positive connections and seem to contribute to compensate ports before release. I can use them in any combination on the front (or back, of course).

  You think that the problem was simply the cables and had nothing to do with the front ports. However, if I plugged the new extension to the front cable, I could then connect the WD drive to that using the original cable that would not connect directly on the front. Which tells me that the strength of the connection of two front port and the original cable was low. Trying to connect these two weaknesses directly was problematic. Solid connectors of the new cable used between two weak points allowed a good connection. This and the fact that the original WD and Rocketfish cables connected to the rear ports 3.0 without problem, points directly to the ports before being part of the problem.

• Satellite M70-190 - problem with USB

  Hello!
  After you uninstall Windows XP and BIOS update, I have a problem with the USB ports. My work does ' t of USB flash drive. Windows also find a USB flash drive, but I can't find it in "my computer".
  If anyone idea about this problem?
  PS, External HARD drive works perfectly, as the USB mouse and USB WiMax modem.
  I m hoping someone out there can help with this problem.

  If I understand you well you don't have problem with USB port, but with a single USB device. Right?

• Portege Z30-A-12N with Port Replicator Port Hi-Speed USB III problems

  Hi all

  I have a big problem with my new Portege Z30-A-12N and Hi-Speed Port Replicator III.

  I connected the power, DVI, LAN, mouse and keyboard to the Port Replicator.
  Power, DVI and LAN are okay, but none will be found if I connect something to the USB Ports 2.0 or 3.0.
  No mouse, no keyboard, and no USB key.

  When I start my Portege I must enter a password after you press the power button.
  These password, I could enter with the external keyboard, but in windows, no keyboard has been found.

  If I connect the keyboard and mouse to the USB Ports of the Portege instead of Port Replicator, the two has been found.

  I ran Windows 7 Enterprise on the Portege.
  BIOS version is 3.30

  Do you have a solution for me?

  Hello

  The HI-SPEED PORT REPLICATOR III PA5116E-1PRP supports 2 x USB 2.0 and 4 x USB 3.0 ports.
  You n t special need Win 7 drivers in order to be able to use the USB ports or other interfaces such as VGA, DVI, audio, etc.

  Sound problems, make sure that the audio device has been selected in the right panel-> sound-> playback tab

  By the way: Win 7 needs USB driver 3.0 which is preinstalled when the laptop was equipped with USB 3.0 ports. My knowledge if your mobile phone does not support USB 3.0, you will be able to use the port replicator USB 3.0 ports.

  Finally and above all devices must be connected before you start the computer. The decision supported and compatible specifications: Portégé R30 - A, Tecra Z40 - A, Tecra Z50 - A, Portégé Z30-A/Z30t-A, Tecra A50 - has

• Satellite M40-307: problem of Audio with USB (pc--> hifi) link

  I have a Toshiba M40 - 307 for a month and a micro stereo system (Philips mc-M570).

  I can link them with USB direct connection to hear the sound from the speakers of Philip pc.

  Only problem: I have several intermittent workers during each session sounds acoustic (movie, game, mp3...)
  I tested it with two other PCs (NEC e DELL) and I didn't have any problem.

  Do you know where the problem may be? USB?
  Thanks for all your replies!

  Hello

  I put t know if this link will help you, because this link contains information on a W2k, but it seems like it might be a Microsoft driver problem.
  http://support.Microsoft.com/default.aspx?scid=KB;%5BLN%5d;817865

  I would recommend to google a bit.

• Big problems with USB devices

  Since I upgraded to El Capitan I have several, serious problems with USB devices:

  1 USB hard drive: everything by watching a video from an external hard drive, the hard drive will be to disassemble all the minutes, the video will be of course hang and it takes 45-60 seconds until the drive reconnects. I also can not boot from any external hard drive more. Booting from a USB key works fine.

  2. I can't transfer my Sunny BT11 of beam data more. The Sunny Beam is a device that records the data of my photovoltaic plant. The overview of the system he sees when connected via USB, however he is not recognized and so I can't transfer data files. Also, it makes not a difference if it is connected via a USB hub or directly, the two versions do NOT work. In the Finder preferences, all devices are controlled to display on the desktop.

  The two scenarios always perfectly work with my Mac mini that has not been updated and uses Mac OS X 10.10.

  Hello Gulliver,

  It seems that if you live with loss of connection of your USB devices since the installation of Mac OS X 10.11 El Capitan, is that correct?

  I suggest that you are troubleshooting by following the steps in this article - OS X El Capitan: If a USB device does not work

  Thank you for using communities of Apple Support.

  Sincerely.

• Problems with USB 3.0

  Hello people!

  I'm here with a need for help to solve a problem that I recently got after reinstalling my windows 7.

  The problem is with USB 3.0 driver, which does not react to any device I plug on two of the ports, and they are not dead I checked that. I tried to re - install USB 3.0 drivers as well and downloaded from HP site for my model, the latest version has failed so I tried with the other older and did not work as well. Only my two USB 2.0 ports work.

  I don't know if there are any other versions or drivers that I could use, those for my model don't work for some reason, and this is the first time I did re-installation of windows for that.

  I would be very grateful if someone could help me solve this problem!

  The laptop model is HP Pavilion dv7 - 6113cl

  Kind regards

  Ed1Ross

  Hello

  Uninstall all the existing USB drivers and then try to install the drivers from this link:

  AMD Chipset drivers

  Restart and check.

• Problems with ports ethernet E4200

  I have problems with my ethernet ports on my router E4200 V1.  I do not get on flow rate of 12 Mbps on a single connected wired computer.  If I replace it with a simple switch 5 port I get 60 Mbit/s using the same cables.  I looked through the creation and cannot come up with any solution.

  Any help would be greatly appreciated.

  Thank you

  Mike

  OK I tore across the network.  Started from scratch and found the problem.  It is quite strange, but everything works fine!

  I discovered through the process of elimination that the cisco router did not like my Panamax Lan UTP.  Cisco is apparently more strict with the signal than the simple switch or refurbished netgear router.  I had the protection on the power strip 6 Max near the iMac.  The totally weird part is that slowed down the entire network.  Streaming is now pending on 60Mbps at each connection to the local network.

  Thank you all for your time I walked through this weird problem.

  Mike

• Problem with USB HUB using Windows 7 on Bootcamp

  I have an iMac when I installed Win 7 with Bootcamp. I have problem with USB hub. If I connect USB devices (printer, iphone... etc...) directly to my computer, it works without any problem. But if I connect them through USB hub, that they do not work properly. The sound instantly invites you, but certain peripheral functions partially and some not at all. I tried several USB hubs... same problem for all. Any solution? Thanks a lot for your answer.

  Hello

  I suggest you to see link and check.

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

  I also suggest you to contact the apple support and check.

  http://www.Apple.com/support/