CP1215 color alignment

Similar Questions

• CP1525nw color alignment is off

  I had my CP1525nw for a few years.  Good summer.  Today, I noticed some colors

  Shading on an image.  To illustrate the problem, I have printed 6 1 "circles;

  Red, green, blue, yellow, cyan and magenta.  The blue circle has a clear magenta

  the shadow of. 05 "in the lower right corner.

  I turned off the printer, deleted and reinstalled the drivers with no improvement.

  I did cleaning and calibration.  I will receive a response.  Thanks, Dave

  I have read that this may be caused by a toner cartridge is low.  Changing the low cartridge can allow alignment complete.

• HP Color LaserJet CP1518ni - color alignment problem

  I'm having a problem with the alignment of different colors with my HP CP1518ni printer. Essentially colors don't print really in the same place, as the impression of Red (Magenta) is never aligned with black / yellow / Blue (Cyan) (so I can have the text in red with a black text shadow 0.5 to 1 mm below or blue with a red shadow of 0.5 to 1 mm at the top for example).

  Troubleshooting always just irritates me to calibrate, but I have many, many times over many months, calibrated and it does not help.

  Does anyone know of other solutions? Or should I buy a new Magenta cartridge and see what happens?

  My cartridges are:

  Magenta - CB543a

  Cyan - CB541a

  Yellow - CB542a

  Black - CB540a

  Make sure that you update to the latest Firmware.   HP recently released a newer version which helped with a more concise calibration with the alignment of color plan.   Many people have reported these problems solved after running the update.

  Update XP (English) can be found here:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=228&LC=en&cc=us&DLC=en&sw_lang=&product=3422472#N841

• Printer laserjet CP1215 color range. Only prints B & W cartridges but the colour.

  I have a color laserjet CP1215 printer. I set the printer to print only black and white and it prints only black and white. Then why my cartridges color short ink? Thank you

  Hello

  Thanks for the post.  I have attached a document below may have useful information regarding about printing with your CP 1215.  Good luck!

  http://support.HP.com/us-en/document/c01416937

• LaserJet CP1215: Color CP1215 print quality - Windows 8.1

  Systematically print very dark colors.  I printed from Word, Adobe PDF viewer and Photoshop all with the same results.   I installed new cartridges and have installed the latest driver.  Since there is no available since Windows 8.1 Toolbox - have not found any way to print the configuration page - hold the results just RESUME button in the gree light of power is flashing but nothing prints.  It seems not to be possible to print a cleaning page.  I'm at a loss what to try to fix this.

  I have downloaded and run the HP print and Scan Doctor 4.6 and everything out OK, the test print that comes out seems OK for me but I don't know what it is supposed to look like.  The cyan block seems a little light.

  Hi dsouleles,

  I see that you have problems with the dark printing. I'd love to help you.

  You can adjust the brightness in the application you are printing from, if this isn't a problem with the hardware with the printer.

  You use windows built in driver or did you download the Plug-and-Play drivers?

  HP Color LaserJet Plug-and-Play package.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Try and print a self-test on the printer hardware to see if it is a hardware or software problem.

  Solving print quality problems. Go to eight Solution: print a configuration page. Is it printed correctly then it would be software related. Let me know the results and how to print the configuration page. Please go well the steps contained in the document. Unfortunately, you'll skip the steps of the box tool.

  If the problem is still related software, you can continue with the following steps:

  Make sure that the correct paper type is selected in the print driver and he is not in default to unspecified.

  Here is a document for the different features in the print driver. Use features in the Windows printer driver.

  What kind of paper do you use?

  Print and Scan doctor, you may have the option in the upper part, in one of the menus to run a diagnostic test, possibly cleaning and calibration of the printer. Try printing Scan Doctor for Windows and HP. Under how to use diagnostic and printer cleaning services?

  Have a great day!
  Thank you.

• Printer HP CP1215 Color Laserjet will reverse only upward when both sides feel

  Recently, I replaced my old Dell XP PC with a new Zoostorm W7x64 Professional OS PC and transferred my HP printer which worked perfectly the new system.  I followed all instructions to update the software and drivers, but now the printer will reverse only upward flanked of printing page even if I chose flip over as my print mode.  I tried the flip up instruction also and it works as it should.  Can I use is no longer my instruction to print two face now that I can't print reports that reads like a book otherwise that manually adjust the paper in the tray.  All solutions, anyone?

  Hi artable ,

  Welcome to the HP Forums.

  I see that you have problems with printing on both sides paper to flip on parameters does not.
  I'll be happy to help you.

  Which driver you have to download and install?

  I download, save and then run the full feature software and drivers if you have installed the Plug-and-Play package to see if that will solve this problem.

  HP Color LaserJet Full Feature software and drivers.

  You change the preference of the printer in the application or in the printer properties window?

  Try another application to see if you have the same problem.

  Please let me know the results.

  Thanks for posting on the HP Forums.
  Have a great day.

• LaserJet CP1215-printing color out of alignment

  Hello

  We have a laserjet CP1215 color and (I think since the replacement of the black cartridge) print colors out of alignment. It seems that only black ink is out of proportion with the other colors. Have tried various recalibration etc, but nothing has worked so far. I've been advised by our IT support company that it's a hardware problem.

  I was wondering if it was just a case of a questionable cartridge that needs to be changed, but we do not have a spare part for the moment so I didn't spend the money on a new if someone could suggest anything!

  I would be grateful for any help or suggestion.

  Thank you

  Rachel

  Hi John,.

  If you are having print quality problems, calibrate the product.

  1 open the HP Color LaserJet CP1210 Series Toolbox.

   

  Open HP Color LaserJet CP1210 Series Toolbox in one of these ways:

  1. In the Windows system tray, double-click the printer icon ().
  2. On the Start menu, click programs (or all programs in Windows XP), HP, HP Color LaserJet

  2. click the Device Configuration file and then click on the page of print quality .

  3. in the field of the color calibration, click Calibrate to calibrate the product immediately.

• HP Officejet Pro 8500 wireless: HP Officejet Pro 8500 W (A909g) 'alignment failed, refer to devicedocumentation for more details'

  I get a lack of alignment. I have replace the printheads and ink cartridges, but it always fails to align...

  The print quality test page print well and seems good... the line calabrate page break will print and look good...

  But when he tries to do the alingment... He quickly spit a page with only a few color line worm at the top of emphasise the full alignment... page after I spit that... He's sitting there for a few minutes... making his usual noise, but said failure.

  I did all three levels of print heads clean... Despite them being new...

  It will print things very well, but I get a monotube color alignment page after each draw with message of misalignment.

  Hey @ataktos,

  Welcome to the HP forums! I hope you enjoy your stay here.

  I see that your Officejet 8500 W gives you alignment failure messages. I can help with that.

  I found a document that can help you with troubleshooting. The document was intended for a slightly different question, but the diagnosis is the same. You can find it by clicking on this link.

  If this still does not resolve your problem, then we can try a factory reset the printer. I will send you a private message on how to reset the printer shortly. If you still have problems after that then the printer will have to be replaced. You can contact the HP Support by clicking this link. If you scroll down on the next page and fill out the form you will find the telephone number of HP.

  I hope this helps and I hope you have a nice day!

• How to print without yellow toner cartridge in a hp CP1215 laser printer. I broke the yellow cartridge.

  I accidentally broke my brand new hp CP1215 Laser printer yellow cartridge. I just want to use only other colors like magenta and cyan etc. But the printer is not printing at all because there is no yellow cartridge.

  Is there a way to print using other colors such as magenta or cyan? I want to type text only (development) using these colors. I use Windows 7 Ultimate and hp CP1215 Color Laser printer.

  I would like to underline a text using magenta or cyan to show important points. I want to use the colors black, magenta and cyan in the text. Changing the settings to print only black and white can not do this.

  Unfortunately, you'll have to buy a yellow toner cartridge to solve the problem.

• Problem with printer color ink large format 7500 has

  Having a problem with the color cartage 920XL

  I tried to print several photos of 4 x 6, where the first is fine and 1/2 way through the other, it starts to print only red

  installed 3 new cartridges, printer head cleaning color, alignment and began to print 4 x 6 photos and the same thing happened.

  Help, please

  I just bought 3 920 new (no large capacity) and was going to try a 3rd time but whated to here from you

  Thanks Mike

  Hi SchneiMB,

  Try the following solutions in the order presented to resolve the issue. When one of the solutions solves the problem, there is no need to continue troubleshooting.

  Troubleshooting print quality problems

• Aligning the print cartridges

  Range of printers all in one HP PSC 1315

  Since receiving Microsoft updates, my computer is no longer offers me HP programs e.g. HP Director, through which I used to do analysis. I can scan with the Microsoft program, so that no problem, but when I change an ink cartridge on the HP, a color alignment page is printed automatically but seems I do not have access to the program that checks the alignment after that I have place the alignment page of color on the plate of the printer. As I am unable to perform this alignment, the printer now prints another page of alignment of color whenever I turn it on.
  How can I make the alignment, or failing that, stop the printer to automatically print a color alignment page whenever I turn it on?
  I can't reload the driver programs or other software that I got when I bought the printer, as they were on diskette, and computers do not have floppy drive.
  Troubleshooting: I checked the control panel for the printer settings.

  Hello

  Thank you very much, it worked.

  This is my first post (second if you include my original request, so don't know not how I "say 'Thank you' by clicking on the star of congratulations in the post who you helped." and "mark the post that solves your problem as"acceptable Solution"", but considered it.)

  Kind regards

  Maurice Wilkinson

• How to change color in CS5 only the font that I pointed out

  Hello

  I am a guardian of the computer, not a web developer. But I know HTML and created my own website using Dreamweaver 8. I just installed Dreamweaver CS5 and am immediately having my first problem:

  I want to change the color of text that I have highlighted on my home page. First of all, the change of the color seems more difficult. In Dreamweaver 8, there was a touch of color in the Properties section on the bottom, but now it seems that I have to click on Format to go through a series of steps, fill out the information. Is in any way simply choose a color (as you would in MS Word)?

  The biggest problem, however, is that when I change the color of the highlight text, half of the text on the page changes color as well. This never happened in Dreamweaver 8. I'm doing something wrong. Is there a way to fix this problem. All I want to do is change a text color without changing the entire Web page.

  If it helps you can consult my Web site home page: http://www.karathecomputertutor.com

  Thank you!

  Kara

  The color is always in the Properties window.  On the left side, the property was split into HTML and CSS.  CSS controls the color, alignment, style, etc., while the HTML controls bind attributes and other actions like that.

  Also, be careful with the CSS classes.  If other elements on the page using the same CSS class it will change the color of these elements as well.

  Unfortunately, because of all the differences in browsers and web design rendering is not as print layout where you can drag-and - drop and just wait until it is.  But like InDesign, you can define the classes (styles in InDesign) to reuse the styles on a page if you need to use more than once which makes it extensible simpler designs while before you need to reselect the same styles of colors/now you can simply assign the class to this piece of code and you're good to go.

• Dynamic text / text entry format font color

  I have a single variable called firstname, and two text fields on the screen, a dynamic text at the top right to display the user name in a small gray font and a larger field of seizure in the middle of the screen. Both have the variable value to firstname, but each field is formatted differently (for example, color, font size, alignment).
  
  When I type the text in the larger field, the size/color/alignment of policies changes abruptly in the smaller field. How can I keep the formatting, but update only the variable?

  Auto Kern has not been verified.

  I didn't know how to get Flash to stop copying of text formatting and the text, but I found a simple solution.

  Do not give the text field variable names. Give them names of instance instead and run this command when you want to update the value of one with the content of the other:

  myTextField1.text = myTextField2.text;

  Which copy the text, not the formatting.

• Text box in iBooks author

  Text imported labour areas Pages normally but created in iBooks author text boxes have a capital font which I could not change.  How can I change the font on a newly created text box?

  Hi Jeff,

  Thank you for using communities Support from Apple. From your post, I understand that you want to change the default font style in the text boxes in iBooks author. I know it's important to work in a way that works best, so I'm happy to provide advice for this.

  Learn about the resources available to us to change the default attributes in iBooks author here:

  iBooks author: change the default attributes for objects

  Digging into the links provided here, I found what seems to be specific to what you are looking for:

  iBooks author: change the font of the text, size, color, alignment and spacing

  Have a great rest of your day, cheers!

• Expression Encoder

  Hello

  I am currently using the application "Expression encoder" for adding subtitles (captions) & markers.
  I need to customize the fonts, the font size, font color, alignment etc. to the legends. I'm not able to find options for this.
  and also I need the option of multiple language subtitles in one video. Is this possible, if so then kindly guide.

  Concerning
  Ankit

  Expression Encoder can be supported in this forum dedicated to Microsoft:

  http://social.msdn.microsoft.com/Forums/en-US/encoder/threads .

  Please repost your question here.

  Thank you.