Dell Precision 5400 - Problema aggiornamento firmware RAID LSI Logic for Dell SAS 6 iR controller

Similar Questions

• DELL new 1 TB drive 6 GB/s SATA is not correctly recognized by DELL SAS 6/ir controller

  I have a Dell PowerEdge R310 with a Raid SAS 6iR controller
  with a SATA 2 x 1 TB drives RAID1 volume.
  The SAS Raid Controller is a LSI1068E chipset.
  Now, I bought a new drive to replace a faulty in the RAID1 volume.
  Has bought the drive with Dell
  400-18614 1 TB SATA 7.2 k 3.5 "HD Hot Plug fully assembled - Kit
  It seems that it is a seagate ST1000NM0033.
  It is a 6GB SATA drive.
  When I replaced the defective drive - the RAID1 game not resync No.
  In fact, the controller has not see the drive. When I plugged the drive
  in another (new), the Bay, and then the controller did see the drive, however,
  it it detected as a virtual disk with only 3950 MB (4 GB)!
  Any idea if this disc is:
  -broken?
  -not compatible with / 3GB SATA?
  -needs jumpers positioned to be compatible?

  Thanks in advance!

  Hi all

  Thanks for the comments.

  However, in my opinion, the disc should work and I shouldn't waste my time at low level

  kind of things. It should be "swap-out/swap-in/resync '...

  So I called the support technique dell that the disc is not good.

  Come back my money - ordered a new one - exactly the same model - and it works very well!

  If the disc was just DOA.

  Thank you all for your time tho.

  Kind regards

  Kurt

• New DELL 1 TB SATA 6 GB not recognized by DELL SAS 6/IR controller

  I have a Dell PowerEdge R310 with a controller Raid SAS 6iR whose volume of SATA 2 x 1 TB RAID1 disks. The SAS Raid Controller is a LSI1068E chipset. Now, I bought a new drive to replace a faulty in the RAID1 volume. A bought the drive with Dell 400-18614 as 1 TB SATA 7.2 k 3.5 "HD Hot Plug PREMONTE - Kit It looks that it is a seagate ST1000NM0033. It is a 6GB SATA drive. When I replaced the defective drive - the RAID1 game not resync No. In fact, the controller has not see the drive. When I plugged the disc in a different (new) bay, while the controller did see the disk, however, it detected as a virtual disk with only 3950 MB (4 GB)! Any idea if this disc is:-broken? -not compatible with / 3GB SATA? -needs jumpers positioned to be compatible? Thanks in advance!

  The drive was indeed defective!

  Come back my money from Dell - élements exact same model and it worked like it supposed to!

  see you soon,

  Kurt

• Failure of Dell SAS 5/ir Firmware update - Precision 690

  I tried to update the firmware on a precision 690 Dell SAS 5/ir and it failed.  I now get the following message when I boot.

  Could not load the LSI Logic Corp. MPT BIOS

  Lack of MRT BIOS 02 h met (XXh, XXh or XXh) PCI adapter

  Fusion-MPT Firmware error code 0706 h

  This machine is the way out of warranty, but works very well.  I have here do anyway to reflash the firmware?

  In case someone else has the same problem.

  Unzip the FIRMWARE. CPE and run the MPTUTIL, then load xxx.fw, then load xxx.rom

  Solved the problem in five minutes

• LSI Logic SCSI Ultra320 RAID Firmware and the BIOS utility. Cannot make the diskettes.

  I downloaded the pack sp29637 for Firmware LSI Logic Ultra320 SCSI RAID and the BIOS utility to my Workstation xw 8200. I'm doing a disk from the downloaded file. I runs the file, but when it tells me to put a floppy disk in the A: drive and I confirm, the window closes and the diskette is not made. Looks like the copy in the file program is corrupted.
  Does anyone have this already developed package files so I can copy them to a floppy disk?
  The files are supposed to be the following:

  Hi Sasi,

  Yes you are right. Then, I realized that I could open these files using Winzip or Winrar. I thank very you much for responding to my post.

• UCS C22 M3 software RAID LSI problem with hard drive

  Hello

  I post here because I searched many hours for a stupid problem.

  I have a Cisco UCS C22 M3 with soft RAID LSI MagicRAID.
  I have two hard disk of 1 TB.
  I create a RAID array with the type 1 (mirror).

  When I run the installation of VMware ESXi 5.1 U1 I see the RAID array, but the two discs.
  I think that it is a driver problem.
  So, I install special with an iso VMware in the VMware Web site for Cisco server.
  I have test with ESXi 5.0 and 5.1, and 5.1 U1 but it's the same problem.

  I try to remove the RAID array and to install esx on disc one monkey. Installation works well, but in the boot menu, I can't boot from a hard disk. I don't know why I search with UEFI and she is disabled.

  I test with windows 2012, and 2008R2 to check if its working but in install I don't see also hard drive or the RAID array.
  I go to Cisco and download the driver of the 2G for VMware Linux and Windows.
  I try inserting the driver in windows install, but does not.
  I think that the driver for a hardware RAID card and software.

  I have try to disable the LSI RAID in the advanced bios "SouthBridge". After I disabled I don't know how I can do to start on the hard drive.
  When I go to the start menu (F6) I see absolutely nothing in drive.

  I test this on two Cisco server.

  I can't know what I can do now. I take a working installation tomorrow and nothing.

  I join you a photo of the boot sequence LSI.

  Thank you very much.

  Sent by Cisco Support technique iPhone App

  Stephane,

  For what I understand, you use the RAID controller integrated, therefore, these drivers will not work you:

  -LSI 92xx

  -LSI 106xE

  -LSI 2008 M

  -INS 3081E-R

  -LSI8708EM2

  -LSI 9201< all="" of="" the="" above="" are="" not="" the="" controller="" you="">

  -CISO 1225 x< this="" is="" for="" the="" vic="">

  -CISCO P81E< this="" is="" for="" the="" 1st="" generation="" of="" vic="" cards,="" so="" definitely="" not="" a="" raid="">

  Pilots are organized into top level by operating system folders, and each folder of OS has a structured series hierarchically who become more specific subfolders so that you can find the exact drivers you need. When you navigate to a folder containing the drivers, it will contain also one or several README files that explains what are these drivers in particular.

  Here is an example of the structure of folder for Windows:

  Windows    ChipSet       vendor          blade-model-number             OS-version-number                All                ia64                Lang (contains language subfolders)                Vista                x64

  You need to look for: /< OS > / storage/Intel/C600 /.< if="" you="" are ="" doing="" the="" installation="" of="" the="" os="" through="" the="" kvm,="" you="" first="" need="" to="" un-mount="" the="" os="" .iso="" image="" to="" mount="" the="" drivers,="" once="" the="" drivers="" are="" done,="" un-mount="" the="" drivers="" and="" mount="" again="" the="" os="" .iso="">

  If it does not, you better open a TAC case that will allow us to put in place an additional troubleshooting Webex meeting.

  -Kenny

• Model of card mother T7500 and configuration of the controller RAID LSI 1068e

  Hi, I just bought a T7500 workstation I would get around mid-December. Because of current prices for HARD drive storage, I decided to go with the 500 GB basic disk up to HEALING of Thailand. Thus, I am limited to basic integrated RAID controller. Because I am not familiar with the RAID configuration, etc. I wanted to read more before I dive in. The starting point would definitely find what was right for the Precision T7500 motherboard. Surprise! I can't find information anywhere. Even Dell people (3 different sales and support representatives) have not managed to tell me it's the Intel 5520 chipset (it looks that they believe that it is the motherboard model...). Well, I'm stuck. I would appreciate if someone could provide me with the model of motherboard and Special Edition, all information on the capabilities of the controller integrated RAID (LSI 1068e) would help me determine what drives should I plan to buy. In addition, one thing that is not clear to me what I inferred from the configuration on the website Wizard is the issue around disks > 2 TB. Of after I read it, I was not able to determine whether the problem was related to the simple readers > 2 TB or if it was related to the management of a storage space > 2 TB (which could be composed of several readers less than 2 TB). What I have in mind (remember that I do not have the machine right now) is to 4 X 1 TB drives in a RAID 0 + 1 (which I'm not sure that the integrated controller supports) configuration that will result in the storage of 2 GB mirrored. The operating system is Win 7 64 bit. Thanks in advance for any info that will help me to prepare my setup (buy hard drives, if I can find cheap ones) and find information on the configuration of the RAID. MrBricole

  I'm sure the T7500 uses an Intel Server Board (since this chipset is located on the Intel site under its motherboards, Dell is essentially correct, even if they didn't know why), but it doesn't matter in the context of your question, because the '' integrated '' RAID controller is not actually on the Board.  It's a card (called "integrated" only because it has a slot on this machine).  Because the functionality of the RAID controller is not on the Board of Directors, Board info will not help you.  Everything you need to know about your Council and the entire system, you can get the T7500 manual.  SAS 6/iR (LSI 1068e) RAID controller information can be found here:

  NOTE from the ADMIN: Broken link has been removed from this post by Dell >

  The SAS 6/iR will not support more than 2 TB of drives, or it will support more than 2 TB of virtual disks.

  It will also only supports RAID 0 OR RAID 1 OR both, but not together (not levels no RAID nested as RAID 10 or 0 + 1).

  So with four 1 TB drives, you can easily do two RAID 1 (called integrated mirror in the controller BIOS CTRL-C)... or you can do two 2-drive RAID 0 (Stripe called integrated in the controller BIOS CTRL-C)... or you can run mode non-RAID, with four individual discs in the operating system.  With this controller, those are your only options with four 1 TB drives.

  If you want / need more features RAID (nested RAID, 2 TB of the VFD above, on board levels, cache, etc.), you must upgrade to the PERC 6 / i.

  Do not buy office records class... Make sure you get enterprise-class drives.  If you decide at some point to go with PERC, not only enterprise class disks will be fundamentally necessary, but certified records would be strongly recommended for stability and performance.

• raid LSI 2308 controller question

  Hi experts

  Someone with experience with the raid LSI 2308 controller? When I look at my card storage in ESX5.5.2 I see. But when I look through cli it says no map found:

  / opt/lsi/bin/sas2flash # / dev-list

  Utility of flashing SAS2 LSI Corporation

  Version 18.00.0.00 (2013.11.18)

  Copyright (c) 2008-2013 LSI Corporation. All rights reserved

  LSI SAS adapters found no! Limited order available!

  ERROR: Command not allowed without an adapter.

  ERROR: Cannot create order-list

  Quit the program.

  / dev #.

  I need to load the firmware first to make it work? Like this guy mentioned here? http://www.yellow-bricks.com/2014/04/08/updating-LSI-firmware-ESXi-commandline/

  I had three SSD that is not at all recognized by ESX and I'm trying to see if the LSI is perhaps what is needed to make it work.

  Thank you

  update the necessary lsi driver. esx5.5.2 removed some less common drivers.

• USRP RuntimeError: Please update the firmware and FPGA images for your device.

  Hello

  I have an Ettus USRP N210 with a surfboard RF WBX running FPGA firmware version 4.

  2009 LabVIEW and NOR-USRP 1.1

  When I try to run one of the USRP VI OR as devices to find it displays the following error code:-1074118627

  "niUSRP Devices.vi finda length or configuration error has occurred."
  Code: 1440
  Details: RuntimeError:
  Please update the firmware and FPGA images for your device.
  See application for USRP2/N-Series notes for instructions.
  Compatibility of the Protocol expected number [7-11], but received 12:
  The version of the firmware is not compatible with the host code generation. »

  I can communicate with unity on Linux using UHD machine and the utility Configuration NI USRP can see the device, but firmware update is not possible, probably because of my IP ending in 221. Latest firmware Ettus was recharged via Linux UHD.

  Looks like my firmware again? I am not allowed to download the old versions of the FPGA firmware.

  Can someone help me with this problem please?

  With respect,

  -Sigurd has.

  Hello Sigurd,

  The NOR-USRP driver requires a specific firmware and FPGA image to be downloaded to the USRP to exploit.

  You can use the utility of Configuration USRP download appropriate firmware and FPGA image to the usrp.

  This knowledge base article will help you: how update the Firmware and FPGAS Images for N2xx and NI 292 x USRP

• Screen resolution signal with Dell E7450 processor and controller. Help!

  Hi All-

  We have some Captivate users who have just received of new computers, touchscreen Dell E7450 processor and controller with WIN8.1 installed.

  We are current users of Captivate 8.

  The issue we encountered is that when attempting to capture using our preferences, screens change resolutions on us.

  Here is what happens...

  1. Changes to the user to screen resolution 1024 x 768 (applys and accepts the change)
  2. Selects to monitor 1, full-screen capture
  3. To start recording; registration ends

  When you look at capturing what we see is that the captured images do not show that 1024 x 768. There are large black borders on one or two sides, and the program that we are captures show left or right raised in a corner.

  When we check the properties, this also shows that the captured resolution isn't what we put on the screen (and still shows). It shows, he changed to 1280 x 960.

  Has anyone else had an experience like that, and if so, how have you solved this.

  We have tried several options, including moving at different resolutions, changing the screen capture to capture the application (which shows the current window too small to see the app), so the addition of an external monitor to see if a capture would work to form it. Nothing seems to work that we can think.

  Any thoughts or resolutions to try would be appreciated that we must make our developers back from work.

  Thanks in advance!

  We managed to find a solution to this problem thanks to Rick Stone...

  The PPP should be set to 100%

  apparently the default dpi has been set at 150% if once we have reset all worked as expected.

• How to: install Windows Server 2008 R2 (64-bit) in ESXi 4.1 - 260247 with controller 'LSI Logic SAS'?

  Hello

  I have a newly installed ESXi 4.1 - 260247 on a Fujitsu - Siemens GROUND RX300 S4 with 2 x Intel Xeon E5420 @ 2.5 GHz with 36 GB of RAM.

  Storage controller is a LSI MegaRAID SAS 1078 6 x 750 GB SATA - drives configured with 3xRAID-1 logical drives. BIOS Version 4.06 Rev 1.04.2519

  Now, I'm trying to install "Microsoft Windows Server 2008 R2 64-bit" in a virtual machine, but fail because the virtual hard disk cannot be found.

  I tried with all Types of SCSI controller, but when running of the "Create Virtual Machine"-magician, he suggests 'LSI Logic SAS'. "." I tried 'LSI Logic parallel' and "VMware Paravirtual" but it did not work. However, I have not tried "Parallel BusLogic", since it clearly says no "recommended for this guest operating system".

  I was unable to find documentation on how and where I can find the "LSI Logic SAS" - pilot to be able to continue the installation. The

  Windows Server 2008 R2 installation is an ISO obtained directly from Microsoft eLicensing.

  I also downloaded the drivers floppy 'pvscsi - Windows2008.flp' and 'vmscsi.flp' from the ESXi server, but the program finds no driver validates the installation of Windows on them.

  I also extracted files "windows.iso' of the ESXi machine, but not drivers there as well.

  So my question is, what model is the "LSI Logic SAS", I guess I can download these LSI directly, I need to know what model?

  Any help appreciated.

  Thank you!

  Kind regards

  Christian

  chrkad,

  I think you have the same problem I had.   Trying to install 2008 R2 and asked for drivers?

  The issue wound up being an ISO corrupt Ms.

  Try to download the ISO using the java-based download manager.  This will tell you if your download is getting disturbed, as mine was.  It will also be the image once completed to ensure you've got the whole thing of checksum.  Just download via HTTP does not.

  I found myself in download the image of the House and burn a DVD and realize that the back of the office,

• New hard drive fails on Windows Server 2008 VM with LSI Logic SAS SCSI controller

  When I try to add a new hard disk to a virtual computer with the cmdlet New-disk hard of a Windows Server 2008 virtual computer, I get the following error:

  New-hard drive: 18/01/2010-14:59:48 New-B8EDFDDF-ACF6-43AC-B111-51D332290FC7 hard drive for the entity vm-315 failed with the following message: "Number of virtual devices exceeds the maximum for a given controller."
  On line: 1 char: 13
  + new hard drive & lt; & lt; & lt; & lt; VM - $vm [5] - capacityKB 4194304
  + CategoryInfo: InvalidArgument: (vm - 315:String) , ViError
  + FullyQualifiedErrorId: Client20_TaskServiceImpl_CheckServerSideTaskUpdates_OperationFailed, VMware.VimAutomation.Commands.NewHardDisk

  When assigning a different virtual machine, for example the parallel LSI Logic Controller, it is not a problem at all. When I add additional disks using the VI Client, there also no problem, regardless of the SCSI controller I use.

  Someone had this problem as well? Y at - it a known solution?

  Hi rengelen,

  I admit that I was pretty murky about when the fix will be available. The thing is that VMware has a policy that employees should not mention liberation time unless we are certain that we can keep his promise of 100%. Hence statemens as 'will be available in a future release.

• Parallel logic LSI, LSI logic SAS, parallel Buslogic (not recommended for the guest operating system), vmware paravirtual

  Infrastructure:

  vSphere

  ESX 4

  Reference Dell R710 Server

  I install WIN 2003 x 64 as a virtual server on ESX 4, when I select LSI logic SAS & LSI logic parallel it does not detect the hard drive, do I need driver if so where can I download?

  For parallel bus logic (not recommended for the guest operating system) & Vmware paravirtual, do I have to select this option for my win 2003 R2 x 64 edition?

  Please help on this issue.

  ~ Rashid

  If you really want to use it for installation, you will need to extract the driver from the VMware Tools ISO and add it to a disk image.

  Dave

  VMware communities user moderator

  New book in town - Start Guide quick vSphere -http://www.yellow-bricks.com/2009/08/12/new-book-in-town-vsphere-quick-start-guide/.

  You have a system or a PCI with VMDirectPath?  Submit your specifications to the unofficial VMDirectPath HCL - http://www.vm-help.com/forum/viewforum.php?f=21.

• Problem installing disktop 800 wireless drivers for windows xp

  Problem installing disktop 800 wireless drivers for windows xp

  Hi Samir,

  I see that you are unable to install the drivers disktop 800 wireless. I'll help you with this problem.

  1. What is the brand and model of the computer?

  2. what security software is installed on the computer?

  3. have you made changes on the computer recently?

  4. What is the error you get when trying to install the driver?

  Please provide us with more information to continue troubleshooting as a result.

  See the link on how to ask questions or help on the Forums.

  Suggestions for a question on help forums: http://support.microsoft.com/kb/555375

  Refer.

  Wireless and wired network problems: http://windows.microsoft.com/en-US/windows/network-connection-problem-help#network-problems=windows-xp&v1h=win8tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• Explorer Windows has encountered a problem and needs to close, sorry for the inconvenience into account only one user. Other user accounts properly.

  This problem deals with only one of my user accounts, where the user accounts function correctly.  When my wife logs in to his user account, it receives the error "windows Explorer has encountered a problem and needs to close, sorry for the inconvenience."  No ICONS or deskbar charge upward; However, my daughter and my user account functions properly.

  I did a system successfully restore to a previous point, but the problem remains.

  If you are still having problems with Windows Explorer crashing, I suggest to consider the suggestion offered by ShadowKat:

  "Hello people, it seems that some guys out there are still having trouble with this random crashes. I have the same problem, except that it happens every time that I go to my media files on my NAS. It seems that there is a bug or something with windows that causes this problem when you access a folder to storage media like mine, especially when the size of the file is very large (archive all my discs of film there for convenience and continuous =), about 1 TB of data). Windows capable of generating thumbnail images for your files and blocks the Explorer as well.

  I solved this by going to my computer > click the "Organize" (upper-left) > folder and search options > view tab check "Show icons, never thumbnails" option and uncheck the "display file on the photos." This prevents windows to generate images and solved the problem for me. Less visually flashy Yes, but at least not need a cloth and restart is).
  Source: http://www.computertooslow.com/windows-explorer-has-stopped-working.asp
  I hope this helps and good luck!
  ShadowKat. »
   
  If you're still having problems after this, I suggest that to start a new thread in the following location:
   
  http://answers.Microsoft.com/en-us/Windows/Forum/performance
   
  I hope this helps.