DeskJet 3052 a: I upgraded my Verizon Jetpack from a MiFi4510 to an EllipsisMHS800L and cannot print.

Similar Questions

• Upgrade RAM P105 satellite from 2 GB to 4 GB and it will not start

  I am trying to upgrade my P105 poles factory PC4300 original 2 from 1 GB to two sticks of 2 GB PNY PC5300.
  The new DDR2 667 Mhz ram according to the web site of Toshiba, however, with the two sticks of the new ram in place (4 GB), my computer does not start.

  With the new ram in place (2 GB) stick, my computer starts very well.
  With two sticks of the original ram (2X1GB) implemented my computer starts very well.
  What gives? Anyone know?

  I read that this laptop supports 4 GB of ram, although only about 3 GB will be mapped for use and this is acceptable to me.
  With 4 GB of ram installed, the BIOS recognizes 640 ram Base and 3 GB of memory.
  Is it possible to get this computer with 2x2gb DDR2 PC5300 ram?

  I am currently running Windows XP Media Center Edition SP3.
  It'd be better if I installed one of the versions the PC 5300 2 GB sticks and one of the original PC 4300 sticks 1 GB?

  Tanks for all help.

  Hello

  In my opinion, the laptop does not start because of the compatibility issue.

  The laptop was equipped with modules PC4300.
  So why you n t using 2 x 2 GB PC4300 modules?
  PC4300 DDR2 533 Mhz modules should run ok.

  If you want to use a PC-5300 and a PC 4300 module, then both modules would go at the same speed as the slower module in your case 533 Mhz.

  This is why they do not since I use a PC5300 and a single PC4300.

  In addition, the module speed depends on the bus (FSB) front.
  If the front side bus support 533 Mhz max then your module would go max to 533 Mhz even if the modules would support higher speed.

• I've upgraded to Windows 7 from Vista on a Tablet PC and have since upgraded to Windows 8. Can I re-use the upgrade of Windows 7 on an another Vista PC?

  I have a Tablet PC originally shipped with Vista installed. I've upgraded to Windows 7 disk 3 license and have since upgraded to Windows 8 with promo code I got when purchasing a new office.

  Can I reuse the license to move an other PC from Vista to Windows 7, since the upgrade to Windows 8 would have been valid for a Vista upgrade?

  Yes, you can transfer the license of Windows 7 on another computer. Why, because the basic license is Windows Vista.

• HP Deskjet 3050 all-in-one a has a deleted document that will not delete. Cannot print anything

  Have a document in the queue of the printer which is "delete", but did not finish the process.  Can't print other documents thereby.  How can I remove the delete document? Thank you

  Hello

  From the desktop, hold down the Windows key and press R.  In the run window, type services.msc and press to enter.

  Scroll down to the print spooler service, right click and select Properties, then click the Stop button.

  Now search for C:\Windows\System32\Spool\PRINTERS, then delete the work inside this folder - you may need to click a command prompt to get the authority to open the PRINTERS folder.

  Restart the computer and you should find that the document has been deleted.

  Kind regards

  DP - K

• HP Pavilion DM4-3105tx: HP Pavilion DM4-3105tx after the upgrade to 1 TB HARD drive won't start not and cannot get into the bios

  Hi all, just need help on my portable DM4 after replace 1TBHDD and unable to start and enter the bios.

  Help, please.

  Thank you & appreciated

  

• OfficeJet 6500 E709n: Cannot print after upgrading Windows 10

  Cannot print. "Doctor print" said there is a software problem.

  Uninstalled the drivers and reinstalled the software complete... twice.

  Capable of printing in color "internal" wireless test page but cannot print a doc and it does not show in the Panel "see what's printing.

  Uninstalled all printers if none showed, in the Panel. When the software has been reinstalled, it showed two Officejet 6500 s on the control panel.

  I tried the post install 'Print sample' with each check printer default and no work.

  Seems that the problem started when I "upgraded" to the new Windows 10.

  Kili2 wrote:
  

  Cannot print. "Doctor print" said there is a software problem.

  Uninstalled the drivers and reinstalled the software complete... twice.

  Hi Kili2,
  
  Try to install your printer via "Open network" - via the window icon or desktop to explore - and choose 'Add devices and printers' (you may need to click the arrow next to the question mark for the top menu show).
  Let the wizard to search for awhile, selcect your printing device, and click 'next'.

  

  After you follow these steps, search for the new installed printer (the name is shown in network for printer and scanner) in "Printers and devices" in the control panel.
  Use this printer as the default printer and you should be able to print over the network cable or wireless.

• HP Deskjet 1051 J410 series: cannot print from HP Deskjet 1051 J410

  I have a HP Deskjet 1051 J410 and cannot print because I updated to Windows 10. I ran the store & under details, he says he detects a problem, but does not say what it is. The printer appears under devices & Printers & said it working properly & has the updated device driver. I have updated the driver from the HP website, but it says driver 1050 instead of 1051. The printer does not appear under Apps > HP anywhere. I removed the

  PRI friendship & reinstalled the HP site I don't have the disk. The USB Port has disappeared after that. So I know that it is not connected to the right port, because it is no longer an option under ports to connect to. A details page of the printer did print at some point, but I can't print from Office, etc. I unplugged the printer from the back & the output. This back in & connected to my laptop HP Presario CQ62 plugged. I restarted my laptop a couple of times. Nothing works. I have also no error message. Can anyone help please?

  Thank you or all of your great suggestions. I ended up doing a repair of Windows 10 installation & that seems to have solved the problem. Thanks again!

• DeskJet 3052 a: could not locate Scan function after upgrade Windows 10

  I have recently upgraded to Windows 10 but I can't find the app when I opened the window to scan for my DeskJet 3052 a.  Windows has a feature to Scan, but I don't want to use it.  I prefer to scan directly to my HP scan window.  Before the upgrade, when I click on the printer series app, I was able to get to the window from there, but now my only option is to add a new printer.   I made the doctor of printing & scanning HP and he added a few updates and analysis of test went well, but I still can't find the scan window.  Help, please!

  Thank you!

  Spoiler (Highlight to read)

   

   

  Hello

  I don't have a printer icon on my desktop.  I have a HP folder only.  He was not yet an option to scan so I clicked on the icon AIO Printer Remote and I was directed to download a Capture & Scan application.  Because I downloaded the application, I now have a separate HP scanning icon.   It is very different from the way it worked in Windows 8, so I don't know if this distance is something different.  However, it works so I am happy.  Thanks a lot for all your help Banhein!

• HP Deskjet 3052 a e-all-in-one: update the printer software

  I have I already know the answer to this question, but I'll ask anyway.  I have a printer HP Deskjet 3052 J611G e-all-in-one has.  My computer is running Windows 7 Home Premium.   I want to upgrade to Windows 10, but the printer I have is not compatible.  I look for updated software for the printer but can't find anything whatsoever.  Is it possible to upgrade my printer software or am I condemned to buy a new printer?

  Thank you for your time

  Spoiler (Highlight to read)

   

   

  Hello

  Your printer is compatible with Windows 10. the drivers can be downloaded from this link:

  http://support.HP.com/us-en/drivers/selfservice/HP-DeskJet-3050A-e-all-in-one-printer-series---J6/4311836/model/5061072

  Don't forget to click on the button to change, and then select Windows 10 in the selection of the BONE at the top.

  Shlomi

• HP deskjet 3052 has works on my wifi after I reset the printer / modem/router - but failed later

  I had my HP Deskjet 3052 a work from PC, MAC, iphone / ipad on my Airlink wifi after a reset on the printer - router - modem.

  It fails when I try to use it later in the day - unless I'm resting again.

  Do I have to reset each time I print?

  New modem/router solved my disconnect problem - but I still cannot connect my imac running Mac OS X 10.5.8.

  I am connected to the wireless - i.e. - accesses the internet, I cannot connect deskjet - is told by the way now I hace a 3520e model - instead of the 3052.

• DeskJet 3052 has

  Print very slowly. Have reinstalled without change. Link on the forum describing the solution is broken. Thank you.

  Welcome to the timmtam forums

  I saw your post on the printing problem slow that you are having with your Deskjet 3052 a. I have a suggestion for you below. Please, try the troubleshooting steps.

  Slow printing

  Let me know the results!

  Have a nice day

• DeskJet 2546 b: Wireless print job stays in queue and poster printer offline after the upgrade to Windows 10

  I write a fix I found for a pretty annoying problem involving 10 Windows and HP wireless printers.

  My Deskjet 2546-b printer was printing OK wireless to the point 8.1 of Windows until that I upgraded my computer to Windows 10. Immediately after I upgraded to Windows 10, I could not scan, so I reinstalled the printer software and has worked for a day or two and then the printer would print not unless I restarted the printer or the computer - sometimes 2 or 3 times. This went on for a few weeks, sometimes it would be nice, sometimes, usually after the computer restarts, he would simply go offline. Once, he went offline 3 times when I was printing about 20 postage labels, recently he went 1 week without any problems.

  Long story short, after a lot of troubleshooting and to help a friend to HP, I found the problem to be associated with the WSD/service Port in Windows 10. My printer still maintains a stable connection with my Netgear router (wireless to the printer light stays on blue) and I was able to scan from the HP software and I could ping the printer... but printing would be just stuck in the print queue (the spooler service) and the printer showed offline in the queue, hardware and windows devices , or when printing from a program like Windows.

  I learned that if I went in devices and printers, until I sent a print job, if the printer showed offline, I could save time by restarting the printer simply and he would come every time (less painful) online.

  

  But it's just a solution and not a solution.

  Nothing worked... not even print and scan doctor. The final fix that worked was to define an IP address manually for the printer, and then I put the print driver to use a standard TCP/IP port.

  Here is the step by step. Your printer must already be connected to your network (solid blue on printer).

  Step 1: Make sure your printer uses a manual IP address

  (1) to obtain the IP address of your printer:

  • If your printer has a control panel with a menu, it's easy... Just look in the settings menu without wire/report and write your printer IPv4 address.
  • If your printer is not a menu of fancy and repower the computer and printer HP Print and Scan Doctor network menu display use (wireless), or you can connect to your router from a web browser (usually 192.168.1.1) and look at attached IPs (like me). Some printers can also print a report of the network when you hold down some buttons everything back up and running, but you will need to search the web site of the Internet or HP to find the process for your printer model - the report displays the IP Address of the printer.

  (2) once you have the IP address of the printer number, type this information in a web browser... like 192.168.1.x (where x is the last number of your printer)

  Web page of the printer should find - otherwise, use another browser (you can use a tablet or iPad if you want). HP has several different forms of printing of web pages (embedded web servers) depending on your printer model, but they all have a large number of parameters.

  (3) since the network tab or section, look for a manual IP address configuration.

  

  (4) suggest an IP address or type in a new.  I've personally used suggest and then replaced by the last number 241. You want to use a high number, something in the order of 240 to 250 to reduce the risk of problems caused by your router assign this number to something else on your network. Note the 4 digits for the new IP address manual, you will use them later.

  5) click apply and close the web page of the printer.

  Step 2: Make the print driver using the manual IP address of the printer

  Open the devices and printers in Windows, right click on your printing device and select printer properties. Follow the prompts to get the WSD port and on a new local port...

  

  1) click on the ports tab.

  (2) add the Port.

  (3) click on after the first screen, and then click new port type.

  (4) enter the IP address of the printer.

  (5) next.

  (6) select the new port.

  7) click OK.

  You have now two pilots displayed in the printers and devices window, you can now print... but you might not be able to scan and the HP printing software may not work as he might want to lets you add a new printer when you open it... If Yes, proceed to step 3.

  Step 3: Remove print devices and install a new one.

  Need to do this to get the software back HP synchronized so you can scan.

  (1) right click 2 print devices listed in the window of your printer and remove them by clicking on remove device.

  (2) open the HP printer Assistant software (from the icon on the desktop or you can search Windows by using the name of your printer).

  (3) installation/add a new printer... go fast and a new device icon is added to the printers and devices window.

  4) return to the printers and devices window and open the properties of the printer again for your printer icon.

  5) go to the ports tab (yet) and you'll see a new selected WSD port, select Port Standard, you created earlier in step 2.

  (6) you have now two print devices in the window (again), but now everything should work.

  These two devices alone from here on out. Do not remove one and everything should work fine. At least it worked for me. I hope it works for you. I'm hoping a Windows update resolves this problem soon, I see many people who cannot print or scan wireless after they upgraded - not just the stuff of HP.

• I'm unable to scan a multi-page document. HP Deskjet 3052 has J611

  I'm unable to scan a multi-page document. I tried everything, re-installed the driver and studied the help settings and there is nothing. Once I scan a page it allows me only to save it and not to add another page to the document. I can't send a pdf CV by attaching two separate pages. I have scanned multiple pages documents other HP scanner and never stumbled on this dilemma. I am running Windows vista and the printer is the printer HP Deskjet 3052 a J611. Help, please.

  Hello

  Don't forget to run the scan of the computer to scan several pages.

  Open the HP software and click on scan a Document or Photo.

  Select the PDF shortcut and if ensure that the dialog box overview checked to be disaplayed.

  Make sure that the resolution set at 300 DPI or lower (any higher resolution does not support multiple pages) and click Scan.

  Use the button to add additional pages until you are finished, and then click Save.

  Shlomi

• Deskjet 3052 alignment failed

  I just installed a new black cartridge on my Deskjet 3052 a. The printer prints the alignment page. I put the alignment on the scanner (right front corner) page and press 'OK '. The printer has worked for a few seconds and then gave me a message that does not have alignment and cartridges have been created for the default settings. Now, whenever I try to print something, I have a message that says that I would get better if I aligned the cartridges. What happened, and what can I do about it?

  Thank you.

  The alignment can fail for several reasons, including black or cyan print does not correctly.  The document here can help solve the alignment failure message.

• How do I do a weird impression & same page with a deskjet 3052

  Is that what I can do to add the functionality to print odd or even pages on my deskjet 3052 a?  This would allow the 2-sided printing.

  Hi Roylrobey,

  Follow the steps below to change the settings for printing for the odd or even pages.

  1. open the printer preferences

  2. click on the paper/quality tab

  3. click on the Advanced button

  4. change the Pages to print the option under the characteristics of the printer