DeskJet 3522 printing scanning copy: hp dj 3522 disconnects wireless network when the printer is turned off

Similar Questions

• J611 3050 has installed on Vista and works very well. Installed on Windows 7 and said always the printer is turned off.

  My Deskjet 3050 a J611 is installed on Vista and it works fine. I then installed on a Windows 7 and the installation went well. No error message came, but when I try to print nothing happens, it just sits in the queue. When I run the diagnostic windows to solve the problem it says the printer is turned off. But it's not far, I can print the Vista machine.

  Download and run this utility on the Win 7 machine: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&jumpid=ex_r4155/en/hho/ipg/forum/network_diag/

  What did he say?

• VERY SLOW (< 200 KB/s) copy between Win7 Machines on wireless network of 300 MB of files

  Hi all

  This problem has been driving me crazy over a week now, and I would really appreciate the help.

  I have a PC under that Win7 Ultimate connected to my Wireless-N 300Mbps network in my office.  This machine connects to the network very well to 104Mbps (limitation of card) and can copy/transfer files to and from our servers of files on this 12-15Mbps n wireless network.  Works perfectly, and I really enjoyed Win7!

  I just added a new ZINO HD (Dell Inspiron 400) with a Dell 1520 802.11 b/g/n wireless NETWORK adapter running Win7 Pro, which will connect to the same wireless n to 216Mbps (according to the "network and sharing Center").  However, all the files that I have copy/transfer to/from the ZINO/from the PC ultimate Win7 or our file servers move at speeds of 54 kbit/s to 972 Kbps and the rate sometimes goes up and down during the copy/transfer.

  I have no problem with the speed of the files uploaded/downloaded from Internet from the ZINO on the same wireless network.  The ZINO has 5 bars on the connectivity.

  I tried to make sure that all of the ZINO drivers are the latest and functioning properly.  I also played with a number of different parameters on the ZINO NIC without change and tried different settings on the router (Linksys WRT150N) without success.  I tested it with the firewall turned on and off and tried a number of other suggestions I found on various forums, all to nothing does not.

  I thank in advance for any help, you may be able to give.

  Hi all

  OK, my team found a solution to our problem.  Here are the steps:

  1. as administrator at the command prompt, type: "netsh int tcp set off heuristic."

  2. follow the instructions that Amrita wrote above.

  First enter: "netsh int tcp set global autotuninglevel = disabled"and restart. "

  Then enter: "netsh int tcp set global autotuninglevel = normal" to give the typical setting.

  3. Finally, go to control panel > programs > turn Windows features on or off > and check ' Simple TCPIP services (echo, day, etc.) so that it is activated. "

  4 restart your system once again, and the file transfer rate should be excellent.

• HP5510 printer hung like a wireless network. How can I turn it go by laptop, on the stairs?

  I have a printer HP5510 hung like a wireless network.  How can I turn it go by laptop, on the stairs?  I always have to go upstairs % turn it on before printing wwill

  You can not, the printer must be turned on to make it work.

• DeskJet 3522 e AiO: how unscrew the head of pint to rinse?

  I found a black movie on youtube on how ti rinse the printhead during printing doesn´t, but it ´s not the same kind of print head. I can't loosen mine.

  It is possible to unscrew the printhead on my deskjet modell 3522nd isn´t.

  So now, we bought a new printer when the printer head is I have included the ink, which was cheeper than to leave the service of the printer.

• Photosmart C8180 All-in-One printer that turns off completely in the middle of printing.

  I have a Photosmart C8180 All-in-One printer that powers completely in the middle of printing, wasting time, paper and ink. It restarts also sometimes more and more and more and sometimes it stops and all the lights blink quickly, show an on-screen error code. During these periods, the power button seems useless. I use the printer with a HP Pavilion dv7 laptop running Windows Vista and an HP / Compaq Presario Windows XP.

  When the C8180 works correctly, it's great. But I can't allow myself to be play roulette of the printer. Help, please. Thank you.

  Thanks to kkcb9395 for your help.

  Unfortunately, I have not found a solution to fix my HP C8180. The 800 number only referred me to another number (866-234-1377) where someone in India tried to sell me a phone support or a new printer. Phone support will not fix a burned capacitor and the new printers HP scan slides. Not to mention the $100. new ink I'll have to eat if I can't solve this problem.

  For anyone who has followed this thread and interested in your own C8180 setting here is a link to a parts list.
  http://www.partshere.com/hppartslist/hpparts.asp?part=L2526A
  If you find a repair manual, let me know.

  I am a customer of HP for HP CEO and longtime who think they have the customer service thing down, I'm on my way to buy an Epson.
  Thanks again for your time.

• OfficeJet Pro 8615: Computer thinks that the printer is turned off

  My computer does not see the printer as being on.  I have the printer connected wireless, but the computer shows it as offline.  When I run the troubleshooter, it tells me to turn on the printer (it's on).  I can scan a document and sends it to the computer but I can not print from the computer to the printer.  I think it's maybe a problem of Windows 10 but I'm not sure.

  Any help would be appreciated.

  I also ran a test network through the printer and everything this past.  Don't know what to do from here.

  I've updated but that does not solve the problem.

  Finish by uninstalling the printer software and reload the drivers.  This seems to have taken care of the issue.  So far so good.

  I think that the combination of the upate and reload the drivers solved.

• F4580, printer: unable to connect F4580 to wireless network after the upgrade of Virgin Media nowhub

  My printer HP F4580 was connected to my network without wire from Virgin Media Superhub. Then I upgraded to the latest Supehub2 of VM (150 MB/s) but the printer does not now connect. We have 2 Macbooks that connect ok for the SSID of 5 Ghz and a cell phone that connects ok for the SSID of 2.4 Ghz. The printer is WPS enabled and therefore the network. I tried to add the printer to the network using the two WPS push and entering the PIN for Client in the VM Supehub Wireless Manager, but neither work. When I get the F4580 to print the wireless network test report prints a WPS PIN and details for the VM in 2.4 GHz network (auth WPS - PSK, AES/TKIP encryption) sees it. The report includes the SSID for my previous network in the configuration summary. I don't seem to have another way to connect elsewhere WPS push or PIN customer WPS.

  In Manager machine virtual Supehub mode wireless 2.4 GHz network is defined as up to 144 Mbs, but it makes no difference if I put it up to 54 Mbit / s. The Security Mode is set to Auto WP, it makes no difference if I put it to WPA2-PSK (AES).  WPS is activated, and push the WPS button on the Supehub flashes when I use WP Push or enter the PIN code of the customer. In both cases, the I pressed the F4580 wireless button so that the indicator wirelss light flashes then than the VM, push the button flashes. Can anyone help?

  I solved the problem of (re-) install the printer on a Windows PC on the same network, using the CD for the printer. The installation allowed me to select the network, and set up the printer for wireless use.

• Wireless connection works only when the printer is turned off

  my desktop computer requires an adapter wireless for internet connection.  installation of this card was problematic and I discovered I mean it was because of my printer - a kodak esp 6150 desktop, which can work wireless.    I can only connect wirelessly when the printer is off on this computer.  However, two other laptops that do not need a separate wireless adapter are able to connect wireless when the printer is on.  any suggestions?   Thank you.

  Hi Moscotty,

  You can read the following article and check if it helps.

  Windows wireless and wired network connection problems

• HP Deskjet 3522 connected wireless but windows 7/8 can't find the printer

  First day, I installed and updated the printer and the software and it worked perfectly, I could print wireless and email with eprint and print it out.

  The day after the computer could not detect the printer,

  Here is what I tried:

  • I tried to uninstall the printer and install again
  • factory reset
  • connect with WPS
  • installed with usb, and then try again to convert wireless
  • I set up the connection manually and also for the software settings to automatically
  • I tried the scan doctor
  • I tried with another computer
  • reset the router.

  and nothing has worked. The printer indicates that it is connected, the only thing I can do, is that it works with the usb and send emails to the printer, then it might print "wireless".

  Hi alex-86. A hard reset is accomplished simply by unplugging the printer while it is on and then with 30 - ish and plug again. I'm not sure that this will solve the problem that you are familiar with. If she works initially then stopped, you can consider power cycling your router as well.

  It is a fairly comprehensive list of measures you should get back up and running. Let me know how it goes.

  http://support.HP.com/us-en/document/c03388454

• How to stop the printer to print the page alignment each time that the printer is turned off?

  I have the HP 2480 all in one printer/copier/scanner. Never understood how to scan to my computer, but it's not my problem. Whenever the printer gets cut and then cut on it automatically prints an alignment page. How can I he stop doing that. I'm tired of wasting paper and ink.

  Hello

  The printed sheet is a part of the process of alignment to align the ink cartridges.

  Make sure you complete alignment by following the steps below, otherwise the printer will keep printing the page because the process was not completed.

  http://support.HP.com/us-en/document/c01764745

  Kind regards

  Shlomi

• Copy, but keep both files is missing when the copy of the Outlook

  Hi all...

  I just found a problem here, in Vista you know when you are about to copy the file it may be an option "copy, but keep both files ' if there is already a file with the same name on this folder.

  But I just found out that if you are about to copy Outlook emails (.msg), this option 3 does not appear. FYI, if you copy outlook emails to win Solution Explorer, the file will be named with the subject of the e-mail, and as you know you will have a lot of emails with the subject even if you had the conversation by using electronic mail.

  Yes, is there anyone can help how to get this 3rd option appear in the copy of the outlook to win explore?

  Hello

  Option "Copy, but keep both files" does not appear when you copy an email from Outlook to Windows Explorer, since it's conception of Microsoft Outlook.

  You can provide feedback to Microsoft on the topic.

  http://mymfe.Microsoft.com/office/feedback.aspx?formid=375

• How can I download a 2nd copy of items 12 to 2nd PC when the download page is not a download now button to click

  I find a page that lists a number of versions of elements whose 12 but when I click on 12 he brings no extra button to start a download

  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If he continues to not try to use a different browser.

  PES 10, 11, 12, 13, 14 - https://helpx.adobe.com/photoshop-elements/kb/photoshop-elements-downloads.html

  PE 10, 11, 12, 13, 14 - https://helpx.adobe.com/premiere-elements/kb/premiere-elements-downloads.html

  You can also download the demo version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  Photoshop/Premiere Elements 12: http://prodesigntools.com/photoshop-elements-12-direct-download-links-premiere.html

• Scan/copy with HP Officejet 8600 pro problems

  I have a desktop HP all-in-one running Windows 7 (64-bit). The printer HP Officejet 8600 pro range is connected to the printer via a USB cable. Scanning/copying is all lines verticle edge edge of the paper. I ran the HP scan doctor software and it showed that everything works. Still no usable copy. Search HP site and the forum of solutions. Tried what I found. Still haven't found a solution. I would set an example of a scan, but I see no abilty to attach a copy of this message. Can someone help me solve the problem?

  The scan looks like the following image?

  

  It s probably a power outage in the lamp.

  1. try to change a different electric recessed contact.

  • 

  2. check the scanner lamp, if he shines a light "BOLD" when the printer is turned on.

  • 

  3. try to start a new search and check the operation of the scanner and how works.

  • If the problem persists, this means that the scanner lamp has a hardware failure.
  • To contact directly to Hewlett Packard to ask the repair options available:
  • Contact HP > http://www8.hp.com/us/en/contact-hp/contact.html

  * Click the stars KUDOS to say thanks

  * also click on the Solution button if your question is answered.

• DeskJet F380 print only page 1 - only when the first powered

  I work under Windows 7. I checked the toner level - not low; cleaning cartridges does not help.  When the power is turned on, the first page prints ok, not strong. The following pages, it acts like it is printing but prints pages white, totally clean.

  Thanks for your suggestions.  I wonder if it's time for a new printer.

  Pablu

  Hi pablu,.

  Welcome to the HP Forums, I hope you enjoy your experience!
  
  I see you are having some problems printing with Deskjet F380.
  I'll be happy to help you.

  I would disable all the start up programs to make sure that something in the background is not cause printing problems.

  Go to start, run, type msconfig, click on the Services tab.
  Click to select the hide all Microsoft Services check box.
  Click Disable all.

  Click on the tab at the top of the page, select Disable all the startup, apply, OK and restart the computer.

  Temporary disable all Antivirus software.

  Then try to print again.

  You will need to go back and allow all when done and turn on the Antivirus software.

  Let me know how it goes and we'll go from there.

  Thanks for posting on the HP Forums.
  Good day.