Directory CUCM EX60/EX90

Similar Questions

• More great series DX vs EX60/EX90

  Have anyone thoughts on these. It is worth now to buy an EX60 above the larger units of office series DX? IF I understand the DX are android where the FORMER are TC based at the base.

  Thanks for your suggestions.

  One of the most important factors to consider is what you will use for call control, CUCM or VCS?

  • EX can use CUCM or VCS.
  • DX can use CUCM only.

  I suspect EX is going anywhere for a while, if they did, then environments based VCS would be left with no end point of office, as the DX are CUCM only endpoints.

• TCS, CUCM, EX90 recording solution

  Dear all

  I need to implement registration between telepresence [EX90, SX20] video endpoint. There is the solution integrated on TCS and CUCM, The SIP trunk between TC and CUCM with the model number of routing TCS.

  Example of

  TC - Extension 9000 [trunk Sip with CUCM]

  EX90 - Extension 1001 [register with CUCM]

  SX20 Extension 0 1002 [register with CUCM]

  Whenever EX90 call SX20., way to trigger the recording to video/voice Trade Commissioner?  

  If I misunderstand the concept., please help give me an opinion.

  Reference: http://www.cisco.com/c/en/us/td/docs/telepresence/tcs/6_2/administration...

  Best regards

  Goal

  If the SX20 or EX90 Multisite option key, one of them can host the Conference.  Any endpoint, it is saying the SX20 must make the appeal out of the TCS.  Suggest you take a look at the sheets and admin guides, they have some information about Multisite.

• Tests EX60 UCM and VCS registration

  Hello

  I did a few test with Cisco EX60 a few days ago a the following infrastructure:

  -UCM 8.6.2

  -Cisco VCS control X7.2.2

  -Cisco EX60 series

  -Csco EX90 series

  -Cisco CPIC

  -Cisco IP Phone

  The goal was to try to save the EX60 in SIP mode with UCM and H.323 mode in VCSC and make some calls with EX60 register in both devices, because I have found no documents where it was stated that only I can save EX60, EX90 in VCS or Complutense University of MADRID, but not in both at the same time.

  I recorded the EX90 in VCS and EX60 in VCS (H.323) and UCM (SIP).

  All calls to H.323 devices EX60 send control VCS and all calls all works fine without any problems. If I try to call EX90 to EX60 in SIP mode, the call will be fails. When the EX90 with EX60 H.323 call is connected, the University Complutense of MADRID and using RTMT I saw that the EX60 was on appeal or in busy state.

  -Audio call of the registered IP phone or CPIC to the AAU to EX60: I saw the call in the call control in the EX60 and RTMT and Complutense University of MADRID, but I did not see the call to the control VCS Cisco. If I try to call to EX90 to EX60 using H.323 right now, I got an EX60 busy tone. Also, if I make an audio call to EX60 for an IP phone I can do another audio EX60 call to an IP phone or an EX90. EX90 try to video negotited but calls finally was audio only.

  -The presence does not work when the EX60 is under appeal with the other end H.323 in the Complutense University of MADRID, too the BLFs do not work and does not appear the call at the Complutense University of MADRID.

  -Si EX60 is videoconferencing with EX90, the EX60 can receive an audio call to UCM get connect and the presence and the BLFs working properly.

  I find no more problems at the moment.

  Kind regards.

  This isn't a Setup program that you want to use, or register them both to the VCSC or

  Let CUCM control your end point, then h323 must be disabled.

• Help to apply the key to unlocking EX90 after upgrade

  Hello

  I upgraded an EX90 to TC5 without adding the key to release first.  After the upgrade, I could still access the web page, but I had to unplug the unit to go home and I contacted TAC for the key to unlocking this morning.

  Now I can't the configuration web page to apply the license key.

  Any ideas what the problem is?

  Ricardo.

  You can hava a computer connected to the same network (same switch, same vlan, same IP range).

  Best have a wireshark running on this computer to see if you get something of the endpoint and tell us what is the result.

  * ping to the endpoint

  * ssh access (e.g. PuTTY)

  * telnet

  * https

  * http

  If it does not lead to you what it is, you can try factrory default reset:

  http://www.Tandberg.com/support/video-conferencing-knowledge-base/FAQ-entries/reset-Cisco-Telepresence-ex60-ex90-factory-settings-628.jsp

  The serial cable would need to have the touchscreen connector,... not sure the pinout.

  If this does not work I would increase it to TAC

• Touch 10 with MX200G2

  Hi, I have a client who has several systems of MX200G1 and just got a new MX200G2 system. They dislike the Touch10 and want to use a Touch8 to maintain consistency. Looking at the specs on the Touch10, it seems that it is designed slightly different from that of the Touch8 (PoE for example). Is it possible to use a Touch8 with the version of the G2 MX200/300?

  The genius of these two devices of contact could resemble a little, but older codecs that use the 8 touch have a different user interface design, then the newer codecs that use the 10 touch, like the latest SX and MX Series have a new user interface.

  Touch 8 is supported only with the following devices:

  • Cisco TelePresence EX Series (EX60, EX90), Cisco TelePresence profile series (42, 55, 65 profile profile profile), Cisco TelePresence MX Series (MX200 and MX300), Cisco TelePresence Integrator C series (Integrator C40, C60, C90) and quick play of Cisco TelePresence SX20.

  Button 10 is supported only with the following devices:

  • MX200/300 second generation and future generations of SX and MX Series.

• Cannot communicate with the server error 11.5 Jabber clients Windows and Mac

  Hi guys,.

  I recently installed CUCM 11.5 (No. Cisco instant messaging and presence) in my lab. Its a simple installation without the LDAP server using the internal directory CUCM to set up customers. I am successfully able to connect to Jabber via my iPhone and iPad on 11.5 Jabber clients or 11.6. I am also able to connect to jabber in windows machine if I use the version of the client Jabber 9.7. However, if I use 11.5 Jabber on the Windows client, it gives me "cannot connect with Server error." On Macbook, I get this error on all the versions I used including old version 9.6.

  The only thing that I noticed that it is option for iPhone Jabber Client forward to put the ip of the CUCM server on option Phone Service only. There are in Windows or Mac Jabber Client 11.6, arrangement for CCM 9 or a later version, where I put my CUCM server IP address.  Am I missing something?

  Kind regards

  S

  Hello

  Just check that you have configured on the system--> the server on cucm entry. If its host name or the FULL domain name, I think your jabber for windows try to solve but unable to do so because of no connectivity to the DNS server or no entry in the DNS server.  Try it below to check if she.

  Change the host file on PC windows from the location below,

  C:\Windows\system32\drivers\etc

  Once you pass on the location and add the cucm entry in the host file, reset your jabber and mention the cucm for connection ip address manually and then check.

• Support for new NAND flash

  Hi all

  As you know, according to the version of the TC TC5.1.4 software, all the codecs of series C/MX/SX/EX newly built have new NAND Flash.

  If some specified software must be applied to them.

  'Series C' means "C20, C40, C60, C90", is this correct?

  It feels strange to me that Quickset has same flash memory with codecs for Integrator as C90.

  Best regards

  Kotaro Hashimoto

  This applies to the C20, C40, C60, C90, EX60, EX90, MX200, MX300 and SX20.

  So yes, you are correct that C-series Endpoint is C20, C40 and C60 C90, but please note this profile include with these endpoint of series C and system.

• Access Cisco profile 42 "Console, syslog and SSH

  Hello

  I profile 42 "with the version of the TCNC 4.2.1265253 software

  I have query on Cisco profile 42 "and 52"

  (1) profile 42 ", I activated the Serial Port Mode 'on '.

  but I am not able to connect to profile 42 "(à l'intérieur de codec peut être c20) the console with onCOM1 rate 38400 baud rate"

  Is it disabled in the profile 42 "code?

  (2) I have configured security-> Audit-> IP server of syslog and logging-> external

  But any change in configuration, I do it on profile 42 "is not loggin to syslog server.

  But other devices such as the VCS and MCU send syslog server syslog message.

  I have attached the profile 42 "screen shot, is there anything else required for syslog?

  (3) profile 42 "with TCNC 4.2.1265253 - SSH software version is not supported?

  even if I enable SSH mode 'on' I'm not able to ssh to the machine.

  (4) we have another point of termination profile 52 "with active encryption version TC4.2.1.265253 software.

  I am able to connect through SSH, but the problem is, it accepts the connection without asking for user name and password...!

  I have attached the profile 42 "GUI config screenshot

  Pls. suggest, if you have the solution to all these questions.

  Thank you

  Rajesh

  Hello

  I tried on my SX20 and I see the messages are sent to the port TCP 514:

  [dderidde-sx20: / var/log/eventlog] $ tcp port 514 - vv x tcpdump

  10:27:03.870003 IP (tos 0x0, ttl 64, id 2654, offset 0, flags [DF], proto TCP (6), length 145)

  DHCP-dgm2-vl300-144-254-13-42.Cisco.com.53345 > drop.cisco.com.514: flags [P.], cksum 0xe629 (correct), seq, ack, 1:94 1, winning 137, the options [nop, nop, Rec. TS 45532890 3096889259 val], length 93

  0x0000: 4500 4000-4006 e792 90fe 0d2a E...^@.@...* 0a5e 0091

  0 0010 x: 0 to 30 a01e d061 0202 dd1b cc8c d 014 3b 09. 0... a... M;.

  0 x 0020: 8018 0089 e629 0000 0101 080 a 02 b 6 c6da...) ..........

  0 x 0030: c7ab 3 38 c b896 363rd 4a 61 3233 2031 6e20... <86>Jan.23.1

  0 x 0040: 303 3 a 31 3236 286th 3720 6529 2073 6f6e a 0:26:17. (none) .s

  0 x 0050: 645 b 7368 3233 3039 345 d 3 has 20 7061 6d5f shd [23094]: .pam_

  0 x 0060: 756 6978 2873 7368 643 a 7365 7373 696f unix (sshd:sessio

  0 x 0070: 3 a 20 7365 and 7373 696f 6e20 636 6e29 c 6f73 n):. session.clos

  0 x 0080: 6564 2066 2075 7365 7220 726f 6f74 ed.for.user.root 6f72

  0x0 0090: a

  I found this DDT which tells me to use the TCP protocol as a "Workaround".

  CSCts98937 - EX60/EX90 and impossible to get work of Syslog C90/C60

  Symptom:

  Not seeing the SNMP or Syslog traffic on port 514 UDP.

  Conditions:

  Normal operation.

  Workaround solution:

  Use port TCP 514...

  Note:

  Make sure you restart the codec after you enable the Syslog.

  Contact the engineering/documentation if TCP is the only mode of transport.

• Any way to see the QoS of packages received in the VC unit?

  Hello

  Is there a way to check or view marking QoS/DSCP of the packets received on a particular unit of VC via GUI or CLI?

  We have a problem of poor audio quality / video in our environment. I'm looking for this to confirm the package QoS (AF41) is unchanged while browsing the network and finally achieve unity of VC.  This will save a lot of time by eliminating the need to make wireshark OCAP.

  Environment:

  Call TMS at the request with the MCU data center

  Different models of VC across the globe - C40, C60, EX60 EX90... etc.

  QoS parameters in MCU and VC unit is checked and they AF41 together.

  Remote sites interconnected through BT MPLS

  The network team has confirmed many AF41 P.C. in remote sites and without releases, errors

  QoS are checked to be good on the network by our team of nw

  Thanks in advance!

  A capture of packets of the endpoint is the only method to display the QoS marking, this can be done via the web interface under Diagnostics > log files, see extended logging.  Make sure that your network switches are not to drop packets or set a low value that is less than the rate of call of the endpoint.

• Directory of CUCM on displayed randomly EX90

  I have a client reporting to me that the list of directories in their EX90 appears randomly. Their systems CTS/TX alphabetical directory display based on the user ID. These EX90s are registered to CUCM 8.6.2a TX5.1.

  Someone at - it experieinced a similar issue or know a way to get the directory to view the entries correctly?

  THX,

  Rob

  HI Rob.  Thank you.  They are mine.  I imported all mine of AD.

  In any case, I took EX60 on TE6 (not yet published) and added to my cucm 8.6.2 (System version: 8.6.2.22900 - 2), and the directory is out of use.

  When I add CUCM 9 (System version: 9.0.1.10000 - 37), the directory is displayed in alphabetical order.

  I "he's double check cop.sgn files and make sure that I loaded everything that he both CUCM, but first glance, ordered (CCM9) and we're not (CCM8.6.2), on the same version of EX60 SW."

  I'll try and reload TC5.1.4 on this unit tomorrow to check on CCM 9 and CCM 8.6.2 too to see what the behaviour is.

  VR

  Patrick

• Can EX60 and EX90 work individually without cucm records

  Hi dear,

  We have a customer need to install EX60 and EX90 without CUCM endpoints.

  : Is my questions really possible to use EX60 and EX90 work individually without CUCM or other registration centralized unit?

  Yes it is possible, the appropriate solution is to have recorded them CUCM or VCS, but you can use them as a standalone endpoint without being registered to a call control server.  See the link in my first reply to an exchange of views on how to set it up as a stand-alone end point.

• EX 60 does not receive the CUCM phonebook directory

  Cisco EX60 is registered on the CUCM, but it does not receive the phone book. IP phones receive the directory.

  Cisco Services for user data is active and running.

  CUCM system version: 9.1.1.20000 - 5

  EX60 software version: TC6.3.1.f768649

  You must mention the URL of the directory on your EX60 in order to extract the CUCM directory.

  EX60 login go to Configuration > server directory > URL and mention of the URL in this format:

  https://: 8443/cucm-uds/users

  First, you can test by opening this URL in a browser to verify if it is correct.

• CUCM LDAP directory

  We have a place that we trunk that has double extensions as connects #3.XXX (with the trunks and dial models) their real extension is in the Active Directory domain IpPhone. We want to show in our so, if we put 3XXX # in the field FAX say or something in AD there at - it means to CUCM map this field? By default, only he only calls and IPPhone.

  Also with regard to the identification of the appellant it shows their true extension and reconstructs a as it is made by their system of course, but is there a way for our system to translate these say Yes if you have a call from them in your call history, that you can remember and it will add the #3 for the extension?

  Mapping of LDAP to CUCM is fixed, you can use only the fields that you get in the drop-down list.

  IP phones do not allocate a unique name to a user directory, you use the fields that you set up with the name as the domain name. Only Jabber made contact resolution against the directory that you are using.

• Cisco Telepresence EX60 records do not in CUCM

  Hello

  Can you help me regarding this issue. Our client has registered in VCS before EX60. Customer decided to registered on CUCM, but before the client has performed a factory reset on the EX60.

  Now, EX60 is not save in CUCM. CUCM version is 9.1.

  And also I already followed the guide for the retail version of CUCM with TC6 firmware.

  Please see attached configuration please. And also attached are the newspapers. And also the error message, we enter.

  Thank you

  The following error may be seen in the papers attached EX60:

  Jun 1 12:47:00.844 ppc appl [2971]: 156,29 SipStack W: [Transaction 32]: got exception SIP_MSG_EXCPT = 8 transport layer
  Jun 1 12:47:00.847 ppc appl [2971]: 156.30 SipReg W: Transport failed to send record (sipexcept: 8 fermΘe by the remote side connection)
  Jun 1 12:47:00.849 ppc appl [2971]: the State of the server SipReg W: SipReg F Unexpected 156.30: 8

  Maybe something closes the TCP on the EX60. Is there a firewall between CUCM and EX60? Can we disable SIP on the firewall inspection and analyze the recording?