DVD player not detected

Similar Questions

• Not getting DVD player not detected in Windows 8

  My DVD from LG drive is not detected in Windows 8.  I started duel with Windows 7.

  As indicated, I typed the following in the admin.

  Reg.exe add "HKLM\System\CurrentControlSet\Services\atapi\Controller0" / f/v EnumDevice1 /t REG_DWORD /d 0x00000001

  In addition it asking me to enter as follows

  Type "REG ADD /?" for usage.

  What should I do now?

  Hello

  Something go right...

  Hover your mouse over the lower left corner of the office. Click right when the start appears, and then select command prompt (Admin)

  Copy and paste this... to avoid typos... and press ENTER.

  Reg.exe add "HKLM\System\CurrentControlSet\Services\atapi\Controller0" / f/v EnumDevice1 /t REG_DWORD /d 0x00000001

  Close the command prompt and reboot.

  This may or may not solve your problem... There are several causes that push lately... but it's a good starting point.

• DVD player not detected, tried a lot of bugs

  Hello

  I would appreciate help. I have the same problem. I worked for a week by applying the fixes without result.  I crossed SpiritX suggestions, but still no solution. I have a HP compaq laptop and the DVD drive (TSST TS-L632H) disappears for no apparent reason. I did a system restore, which reinstalled the settings and the original software factory. The drive reappeared just after the system recovery, but now it appears and disappears randomly. Microsoft Fix It does not set it. There is no higher or lower than the registry filter. Device Manager does not show it. I have Vista Home premium. Sometimes I boot, and there it is. However, later she disappears.

  Once I opened my computer after the reboot. I saw the disc was present, and then then the Green loading bar was moving until the end on the top of the workstation, I saw the disk disappears. I tried to take out the drive and put it in, does not help. If I do the system restore to a time when the player was present, after restoring it is not yet present. I wonder if Windows DVD Maker is causing conflicts. I can't find any other software, not to mention that of Dvd burning. I can't uninstall DVD Maker because it is part of the operating system. Any ideas? Help, please!

  God bless you
  J.

  Hello

  Step 1: You can also check with the manufacturer to check if they have any firmware update that could solve the problem.

  Step 2: If this is not the case, try to connect the CD/DVD drive to another computer and see if the problem still occurs.

• CD/DVD drive not detected in 'my computer '.

  Ok.  That is the problem.  A few weeks ago, I couldn't find my CD/DVD device in 'my computer '.  I read the solution involving the modification of the registry.  Scary stuff, I know, but I did everything very carefully and removed the filters superiors and inferiors, and Wallah, it worked and my CD/DVD device appararurent again and I was able to open a CD and look at the files.  The same thing happened again, but when I look at the registry fix again he has no less and the top filter to remove.  I ran all kinds of diagnostic tools Microsoft Mr. Fix and after execution, gently, he finally tells me "the CD/DVD device not detected.  Well, DOH!  I already knew!  But how to fix it? I have a HP laptop with a build in the drive.  When I put a CD in the tray and close it I hear all the normal whirring etc of the currently playing disc, but nothing happens.  Absolutely nothing - a bit like these emails that promise miracles that if you pass them on to 10 people, absolutely nothing happens.  Please help - in non-technical terms please.  I am a user of the computer, not a grumpy, instructions must be simple.  Oh, I must add, after reading other topics of the forum, my tray works perfectly.  I can load and unload CDs.  Finally, my CD/DVD drive IS NOT doesn't appear in Device Manager if no suggestion re clicking on the disk or drive in Device Manager.  IT is NOT THERE.

  Hello

  You have loaded CD/DVD programs just before this started happening? Often those who will compete
  for resources that load themselves into memory and the interaction parts cause strange problems.

  Check with HP Support, their drivers and documentation online and ask in the forums known HP
  questions.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ------------------------------------

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• DVD player, not visible and detected

  Hello

  I am using windows 7 home 64 bit on HP Pavilion dv4-3031tx laptop. A few months ago I changed my DVD rom HP service center drive as the engraving option did not work. After changing, it was working fine. Now, the drive is not visible when I opened my computer. I installed all the drivers again from the recovery manager supplied by HP recovery disk, but it is still the same. Strange thing is when I insert my recovery disc and restart my boot of seleting for laptop to DVD option, can detect the disc and the approaches for installing the OS. If possible, I want to slove this problem rather than reinstall windows recovery disk I have tons of programs installed in HD. Please give an effective solution. I'm really worried.

  Thanks in advance.

  It's a pretty common problem and there is a Microsoft Autofix to this:

  http://support.Microsoft.com/kb/982116

  You can run the automatic setting, but I had more chance to do manual registry change which is also described on the link.

  This is called the problem of upper/lower case filters and is the very low level driver built-in to Windows.

• CD/dvd drive not detected

  original title: cd/dvd player

  CD/dvd drive is not detected
  one or more specific class filter drivers is missing or damaged

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• DVD RW not detected

  DVD player is not listed in my computer and Device Manager. No upper or lower filters shown in the registry. If I put a disc in the DVD drive, it starts the rotation and then stops. Tried to detect the hardware in the Device Manager, but did not. Tried to install the driver, but the system indicates that the driver is the last. Tried to Fix It, but an error that indicates the CD/DVD drive is not detected. Remember, not all new software installed. How we solve it? Or is this a hardware problem?

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Code 39 CD/DVD drive not detected

  Hi, I had to reinstall Vista because my files were corrupted by using Microsoft e-mail support.  I tried to install Windows service pack 2, but it would not be installed. After repair corrupt Vista files and finally get service Pack2 installed, I have had to reinstall a software disc that came with my computer Dell. The cd/dvd drive makes noise but does not read the disc. I logged on the Dell support site and follow their recommendations without success. I have downloaded the recommended bios and firmware dvd, uninstalled Roxio Creator and dvd driver but the system goes on to say that the drive is not detected. Finally, I called Dell and, of course, only the equipment is under warranty and I can't afford to pay for the software support. My computer is 8 months old and I rarely use the dvd player. It worked fine before these repairs and upgrades. My system is Vista 64-bit with service pack 2. According to Device Manager, my dvd player is number model PLDS DVD +-RW DS - 8A3S. BTW, as part of my purchase last summer that I was sent disk to upgrade to Windows 7 for free. I didn't want to hassle with installation at the time, but after pass by all this... should I go ahead and upgrade to Windows 7 after I receive my dvd player work?

  Hello

  Code 39 means that the driver is corrupted or missing.

  Please make all below even if you have done some before as it is often the total process
  which solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then check the cables
  both ends. Remove and replace, do not just tight. For laptops, you can often clean the
  power and data of the contacts with a pencil eraser.

  --------------------------------------------------------------

  Also check with your system manufacturer to see if there are any updated drivers for your DVD. Or
  even if there is 'old', you can reinstall. However, many use the default Windows drivers
  Some will be more special. Also check the website of the manufacturer of the car.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• DVD player not recognized; error code 10

  Our Museum has a Dell Optiplex 745 on which the XP operating system has been replaced by Windows 7 Professional.  The DVD drive is not recognized, and the error code 10 stipulates that the driver could not be loaded.  I tried upgrading the driver online, but I was told that the driver installed is the right one for this player.  If I remove the drive with the machine on, uninstall the driver, stop and then restart and then restarting to reinsert the DVD, the computer recognizes the drive and install it and it works.  When you restart the computer the next morning, the car disappeared again.  Would appreciate any help I can get!

  Thank you!

  Werner Horlbeck

  Hello

  Read this link which has also a few solutions:

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  --------------------------------------------------------------------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find CMD top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I have a problem with the DVD drive not detected on Windows 7.

  I built a new PC (I've built a few of them).  This time is not considered my ASUS BD player with Windows 7 DVD burner.  It is not in either Device Manager just do not at all recognized.  The BIOS for the ASUS P9X79 of luxury see the SATA drive without problem.  Sometimes after restarting the BD Player looks and functions perfectly, but when the computer goes to sleep or shuts down is usually not there when it is restarted.  Please help me solve this problem :-)

  Original title: optical drive not recognized...

  Hello

  Please contact the Microsoft Community.

  You have a problem with the driver DVD being missing on the computer. It can be difficult when something that is important to you does not work as expected. It's pretty simple and we're here to help you solve the problem. We work as a team and get this sorted out.

  Please answer these questions-

  (1) that you get an error message or error code?

  (2) did you have performed the steps in troubleshooting?

  (3) have you made changes on the computer before the show?

  I would like more information about the issue.

  Method 1-

  I wish that you are running the fixit-

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2-

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.
  Back up the registry - http://windows.microsoft.com/en-US/windows7/Back-up-the-registry

  I would have you look at the article-

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116#top

  Let us know if you have other questions about Windows in the future. We will be happy to help you. We at Microsoft, strive for excellence and provide our customers with the best support.

  Thank you.

• Install on MacBook Air - DVD player not recognized

  Strange problem.

  Just picked up my MacBook Air today and went to install VMWare Fusion.  Plugged in an optical dvd/cd drive and it is recognized by OSX - the disc appears on the desktop and I can navigate it very well.

  I launch Fusion and he sees not the drive - no button continue unless I keep the DVD player.  The second screen does not see the CD/DVD.

  What I am doing wrong?  Seems if OSX saw the disc, it would be the merge.  It's a serious iso on a DVD of MSDN Windows 7 x 64.

  Going along for an hour trying to understand this.  Any help would be greatly appreciated!

  She was told that I need to run vmware, rather than worrying with bootcamp or parallels.

  Thank you!
  JOHN

  HM, test this point, I expected it to work, but in my results, I was not able to make reognized on my MacBook Air.

  I tested and then on one of our test machines (which is a bit outdated, running 10.6.5 and missing the update of the firmware to 2.0 EFI) and it worked.

  We have improved this test to 10.6.6 machine and it no longer works.

  So it seems that Apple has changed something, and who broke our EasyInstall to physical DVD drive detection.

  Therefore, you can create a disk image using disk utility and install using that for now until we work with Apple in order to understand who has bug is.

  Here's our KB for how to do this:

  http://KB.VMware.com/kb/1015406

  Please mention!

• DVD player not working not not on Satellite Pro U400-142

  My DVD player does not work. I insert a disc, you can hear the drive works for some time, but then nothing happens. I checked the Device Manager' - under readers of CD-ROM/DVD-ROM it shows: MAST * A DVD-RAM UJ862AS, but there is a black exclamation point in a yellow circle next to it. I opened the dialog box 'Properties' and under the status of the device, he wrote:

  "Windows successfully loaded the device driver for this hardware, but does not the hardware device. (Code 41)

  I would try try to resolve the problem by reinstalling the driver. I checked Toshiba site for the driver, but can't find it.

  I would be very grateful if someone could give me some ideas on how to sove this problem.

  Thank you

  P

  What you can do is follow:
  Remove the optical drive from Device Manager drive, restart your laptop.
  The reader should be acknowledged and properly installed. If the same thing happens again try it please > http://aps2.toshiba-tro.de/kb0/FAQ8101LA0000R01.htm

• DVD player not working not not since upgrading to Windows 10?

  Improved to win 10 of Win 7 and now cannot get my DVD player to work. Checked info from Device Manager which advises (Windows cannot start this hardware device because its configuration in the registry information is incomplete or damaged (code 19).) I tried to remove and reinstall the DVD player, but the error message still appears. Any ideas of how to solve my problem?
  My last resort would be to roll back to Windows 7 if I can't figure it out. : confused:

  I have the same problem with my SATELLITE A500 - 19(d) is code19 drivers must not be installed correctly.

• DVD player not working not not Satellite Pro A100 - Code 37 error

  Hello

  Someone help on this?

  I have an A-100 and the DVD player has stopped working in XP. I checked the Device Manager and see XP disc but returns this error "Windows cannot initialize the device of this hardware driver. (Code 37) »

  I also noticed that ASAPI.sys is not running in the Task Manager.

  I'm guessing this has something to do with the problem.

  I tried to reinstall the device drivers, but this made no difference. Any suggestions?

  Hello

  Error code 37 means the driver returned failure from its DriverEntry routine.
  You can try to delete the driver from Device Manager and rebooted the new OS should recognize the drive device and initialize the driver again.

  If this is not enough, try this procedure:
  Run REGEDIT and open the following folders:

  HKEY_LOCAL_MACHINE
  -> SYSTEM
  -> CurrentControlSet
  -> Control
  -> Class
  {4D36E965-E325-11CE-BFC1-08002BE10318}

  After you click {4D36E965-E325-11CE-BFC1-08002BE10318} you should see two settings on the right side:
  "Upperfilters".
  'Lowerfilters '.

  Click on each of them, press DELETE, and then click YES.

  Then restart the laptop and see if it was useful.

• DVD player not working not not on Sat 1800-614

  Hello

  I bought a Satellite 1800 614 3 years ago, provided with a DVD player. At this time there is no problem to read the DVD. I did not use it for a while and when I tried to use it I discovered that it does not read new DVD, I can see the movie but the two images and audios are dispersed and disrupted last year. It only works with the old DVD (2001-2002) and DVX and so on...

  I was told that it is because they changed the format of DVD or something like that. Can you help me to fix it? Is it possible to update the BIOS any help? Maybe the firmware? You know the one that I need and where I can find it? I tried to update the drivers for DVD but it seems that he does not accept the change. Do you know how to update the drivers too?

  THANKS TO ANYONE WHO CAN HELP! I HAD THIS DVD PLAYER AND I NEVER GOT TO USE IT!

  Hello

  I put t know if you tried, but you can try to install some beyond news who is responsible for playing movies on dvd (files)